My phone keeps displaying a white screen with the apple, then occasionally flicks to a blue screen, but won't turn on! HELP!!
My phone keeps displaying a white screen with the apple, then occasionally flicks to a blue screen, but won't turn on! HELP!! I have had it on charge all day and have tried plugging it in to my computer to sync.
Restore your software using iTunes.
Turn your device off and connect your cable to the computer, but not the device just yet. Start up iTunes. Now, hold down the home button on your device and plug it in to the cable - don't let go of the button until iTunes tells you it's detected a device in recovery mode. Now you can restore to factory settings.
You should be able to restore your backup file after this procedure. If the problem comes back, you either have corruption in your backup file, or a serious hardware problem that should be looked at by a tech at the Genius Bar (make an appointment first).
Similar Messages
-
Installing IOS 8 on my iPad stuck on white screen with the apple. Help please?
I'm in the process of installing IOS 8 on my iPad 3, and it is still on the white screen with the apple. It has been on this screen for 24 hours now with no change. Can anyone help?
If it has NEVER been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this. -
I have a 4th generation 8GB iPod nano and it will not progress past the blank screen with the white apple logo on it. I have charged it fully and tried to restart it by pressing and holding the menu buttons for 3-7 seconds. The devices screen will turn off and then, after a couple of seconds, the screen with the Apple logo will appear again. This screen will remain lit until the iPod runs out of battery again. I have tried plugging it into my Macbook Pro. I have the newest versions of iTunes software and OS X Mavericks. The computer will not recognize the iPod and the device will not show up in the computers list of devices. I looked up the troubleshooting for the device and found out how to put the device into disk mode. I followed the intructions but the iPod would not go into disk mode. The screen still displayed the Apple logo and would not set into disk mode. I fear that I have run out of options. I have come to this forum in hopes that I can still salvage my device. If there is anything I can do, please loet me know so I can try it. If not, I am affraid I will have to go to an Apple store of authorized retailer and have it repaired or replaced.
Try manually connecting the device to your PC in Disk Mode and then restoring it iTunes.
From http://support.apple.com/kb/HT1363
Putting iPod devices with a Click Wheel into Disk Mode
If necessary, verify that your iPod has a Click Wheel.
Before placing the iPod into Disk Mode, verify that it is charged.
Toggle the Hold switch on and off (set it to Hold, then turn it off again.)
Press and hold the Menu and Select buttons for at least six seconds, until the Apple logo appears.
When the Apple logo appears, release the Menu and Select buttons and immediately press and hold the Select and the Play/Pause buttons until the Disk Mode screen appears.
Connect the iPod to your computer; the screen on the iPod will should say "Do not disconnect".
If you are having difficulty putting your iPod into Disk Mode, set it on a flat surface. Make sure that the finger pressing the Select button is not touching the Click Wheel. Also make sure that you are pressing the Play/Pause button toward the outside of the Click Wheel and not near the center. If you are still unable to put your iPod into Disk Mode, use one finger from one hand to press the Select button, and one finger from the other hand to press the Play/Pause button.
B-rock -
My computer will not start up. It powers up, I get the gray screen with the apple, then the loading progress bar starts loading to about 25% the the screen goes black. what can I try to get my computer up and running?
Carolyn Samit wrote:
iMac, Mac OS X (10.7.1)
Use Command + R for Lion Recovery
Try restarting, when you hear the startup tone hold down the Option key. Then choose the Recovery Partition. -
i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s...
plugged the charger in the wall, it gives me a black screen then the white screen with the apple logo, then repeat....
i tried the dfu thing and now the phone is saying connect to itunes, when i plug the phone outta the wall, the phone goes dead.....
plugging the phone into the laptop NOTHING!!!!!!!!!!!!!!!!!!!!!
the laptop doe read my phone.....
no ding.....
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going onmariidb wrote:
i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s... {snip}
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going on
That's the problem. That's what the **** is going on. -
I bought my 6 plus last night decided to upgrade the IOS 8 like they suggest and now all I see is a white screen with the apple sign in the middle with an occasional flashing red screen. Did my new phone seriously just crash? What do I do now? I left it overnight with the white screen, thinking maybe it'll go away and needs time to upgrade. Woke up this morning, nope still white screen. Very disappointed with Apple. I was so excited to get my phone and can't even use it right now.
First turn the iPhone off and back on and see if it works. If that doesn't work then do a Reset by holding the Sleep / Wake Button (The Power Button) and the Home Button at the same time until the white Apple Logo appears, the release both Buttons and wait until a Full Reset occurs. The iPhone 6 should come back to your Lock-Screen. If that doesn't work then you could connect the iPhone 6 via the Lightning Cable to a Computer with a Current Version of iTunes. Then open iTunes on the Computer and wait until your see a Button that represents your attached iPhone and click on it. This should bring up a Summary Screen on the Computer within iTunes. At that point your can choose Update Software if an Update is available or Restore the iPhone to Factory Settings / New In The Box, or you could try to Restore from your Backup if a current Backup had already been saved from a previous iPhone.
If you don't have a computer with iTunes and you can get the iPhone back on, then go to Settings>General>Software Update and see if the iPhone is still on iOS 8.0 or if it is now on iOS 8.0.2 -
I Mac freeze: When powered on all I get is a blank white screen with the apple logo. No "beach ball" nothing more. Tried all the usual restarts. Help?
Tried all the usual restarts. Help?
Care to share?
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.
===========
Your profile is a complete blank!!!!
When posting in Apple Communties/Forums/Message Boards.......It would help us to know which Mac model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
CLICKY CLICK-----> Help us to help you on these forums
***This will help in providing you with the proper and/or correct solutions.*** -
Hey everyone,
This morning i took my phone out of the charger and everything was normal however, once i got in the car i looked at my phone and realized it was turned off. I tried turning it on again as well but all it does is going to the start up screen (The white screen with the apple logo) and then it turns off again as well. I also put it on the charger but it does the same thing but repeatedly. So it just goes to the white screen and off again. At last i resorted to recovering my phone even if it meant losing all my data. Slow internet connection meant it took all night but in the morning i recovered and everything and got to the last step ( It told me its finished but i should leave my phone connected to itunes and it will pop up there) but all that popped up was an error screen. It still broken but now sometimes when i try to turn it on the same white screen with the logo comes on with a bar under it. this bar fills up a little then the screen goes black again. Is there any other way i can try to fix this?
P.S. There are no apple stores in my area so i took it to one of the phone stores here and even they said they couldnt do anything about itTry:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
my MacBook Pro is crashing and Mac OS stops working sometimes so I have to restart it. And sometimes it stays on the first white-ish screen with the Apple and won't start further.
What to do?
Does that mean that the is the end of my Mac Book 5bought in the summer of 2009) ? Or is there someting to do to fix it?
Thanks
VTry this:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update. -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
i've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?
Look at this support article:
http://support.apple.com/kb/ts2570
Ciao. -
I have a macbook and when I power it on and then select myself as a user...It won't power up. It stays in the white screen with the apple logo. I am online currently under 'guest user'. Is there anything I can do from the keyboard to fix this??? Help!!!
Could you specify the model of MacBook and the OS X it's running, please? Some of the advice or references vary along with the system, so this could be helpful to formulate a reply. I've never used a Guest User selection, but do have more than one User.
If the computer does not have an optical drive, you may be able to boot it into a recovery disk mode or something; in an attempt to see what is wrong and maybe fix it.
Good luck & happy computing! -
I tried to reset my iphone 5 from the phone and not a computer. I have had a blank screen with the apple logo and a full progress bar. I can not get my phone to restart. What can I do?
Sorry i meant iOs5 to ios 5.0.1
-
I have an IPod 2nd generation I bought from a pawn shop. It worked for a day but now when I try to charge it, it keeps switching back and forth from the large full screen icon of a low battery and a lighting bolt below to the blue screen with the apple symbol in the middle. I had it on charge all night but still dead.
Try here.
iPod touch: Hardware troubleshooting
You may have a hardware problem.
Maybe you are looking for
-
N80-best place to repair faulty keys?
My week old N80 has developed a serious fault with the 'menu' and 'right' 'down' navigation keys no longer working. It seems like I have two options. 1)Take it to my local service centre, probably a branch of the carphonewarehouse, none of whom answe
-
How do I join text to shapes in pages?
how do I join text to shapes in Pages?
-
Hi, What are context operators and where should we use? Thanks in Advance
-
Trouble creating custom combobox
I'm building a custom component consisting of a combo box that autopopulates with a list of states. So far it works fine except I can't retreive the selected item from an instance when the user makes a new selection. I've tried setting a custom prope
-
BACKGROUND: In support of the U.S Navy, I've developed an IETM in XML and distributed it as PDF documents (in the Windows XP environment) meeting the current Military standards. My new tasking; However, is to ensure that this project can run on both