My printer display screen blank

My printer display is blank and does not want to come on.  How do I recover the screen

Unplug the printer from the wall outlet and wait 10 mins.  Plug it back an and power on the printer.  Do you have a screen now?
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Similar Messages

  • PRINTER DISPLAY SCREEN ALMOST COMPLETELY WHITE (TOO BRIGHT/FADED/?)

    I cannot read the images on my printer’s display (Product HP Officejet Pro 8600 e-all-in-one printer - N911a). The images are there, but barely discernible. I can't put my finger on whether the screen is too bright or too faint, or the images are too light. The display is NOT blank or black (and the HP Troubleshooting solutions to correct those problems have not corrected my problem, ie Hard Power Reset, updated firmware, and adjusted brightness setting), just too bright or too faint. Even with the screen brightness on the darkest setting, I still cannot make out the images. Interestingly enough, at the end of the day yesterday, the screen self-corrected somehow, and was back to a readable display. However, it reverted back to the problem overnight.  

    Hi busymom51 & otcheryl,
    I understand that your issue is not the same as the title of the troubleshooting guide listed above: The Touchscreen Does Not Respond, however the troubleshooting steps are the recommended steps to attempt the resolution. If you followed the steps and the issue is not resolved, try again to update the firmware.
    If your 8600 is the N911a, try this firmware update: HP Officejet Pro 8600 N911a Firmware. The printer will need to be connected to a Windows computer via USB for the firmware update.
    If the 8600 is the N911g or N911n, use this update: HP Officejet Pro 8600 N911g_n Firmware. The printer will need to be connected to a Windows computer via USB for the firmware update.
    If the firmware update does not help the dim display, contacting HP's Technical Support to see about further options for you would be the best option.
    If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here.
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • My printer display screen is unreadable so i can't connect to my network. is there another way?

    Deskjet 3050
    Was previously connected to network but won't connect again.  Since I can't read the screen to choose the correct options all I can do is print a test page.
    thanks!!
    This question was solved.
    View Solution.

    If you follow Method One: Install the software with the product CD, it does not have you do anything on the printer.  This step is listed further down in the document and everything above it is more or less preparation for this step.
    The step before this has you do a WPS option which does get performed on the printer, but this is not necessary and I highly recommend skipping this step.
    It may be best if you uninsalled the printer software from the computer before performing the steps so that what you experience matches what is in the steps for your printer.
    Assuming the software is uninstalled, the following steps summarizes what needs to be done.
    1.  Connect printer to a PC (make sure the PC is on your wireless network) with USB cable.
    2.  Install the software.
    3.  During the installation it will ask if you want the printer connected through USB or network.  Select network and it will add the Deskjet to the same network as the PC.
    4.  Follow the prompts and it will have you disconnect the USB cable.
    Once all the steps in Method One: Install the software with CD have been completed, your printer will be connected to the wireless network without doing anything on the printer control panel.
    Edited for spelling
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • Do i have to have a eprint app on my printer display screen in order to print from my iphone

    do i have to have a eprint app on my dispay screen on the printer inorder to print from my iphone

    what you need is a wireless router configured to you hp printer.
    then a print & share software available here:
    http://itunes.apple.com/us/app/print-n-share-for-advanced/id301656026?mt=8
    Although I am working on behalf of HP, I am speaking for myself and not for HP.
    Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
    If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
    Happy Troubleshooting : )

  • My HP Officejet Pro 8600 stopped printing and display went blank although machine was on.

    My display screen went blank and printer stopped working.  I followed online troubleshooting instructions and got printer and scan to work again by using computer however the display screen is still blank. The arrows and home button on the sides light up. the only thing I noticed before this all happened is the ink was low. Any suggestions?

    My display screen went blank and printer stopped working.  I followed online troubleshooting instructions and got printer and scan to work again by using computer however the display screen is still blank. The arrows and home button on the sides light up. the only thing I noticed before this all happened is the ink was low. Any suggestions?

  • Adobe reader xi i am running 2 display screens and when i have a file open and go to print the print page opens on my second screen.  How can I get adobe reader to just display on one screen?

    adobe reader xi i am running 2 display screens and when i have a file open and go to print the print page opens on my second screen.  How can I get adobe reader to just display on one screen?
    I want the capability of adobe reader to just run on one screen.

    I had the same problem.
    Try this.
    https://igppwiki.ucsd.edu/groups/publichelpwiki/wiki/a1538/Howto_Disable_Acrobat _as_the_Safari_PDF_Viewer.html

  • My iMac is connected to a Brother printer. I have Snow Leopard 10.7.3 As of yesterday, when I try to print a PDF it prints as a blank black page. Does anyone know how to correct this so that the PDF will print as I see it on screen?

    My iMac is connected to a Brother printer. I have Snow Leopard 10.7.3 As of yesterday, when I try to print a PDF it prints as a blank black page. Does anyone know how to correct this so that the PDF will print as I see it on screen?

    If you are running Mac OS X 10.7.3 then you have Lion installed, not Snow Leopard. It's probably not important to this discussion, but something you should be aware of.
    What application are you printing the PDF files from? Have you tried opening the PDF file using the Preview application that can be found in the Applications folder? Does the issue still occur? Have you tried other PDF files from a different source?
    Another poster in the following discussion thread reported that this method resolved their black blank PDF issue when viewing (and presumably printing) PDF files from Safari.
    https://discussions.apple.com/thread/3890509?start=0&tstart=0
    This solved my question by mcbuffy  on Apr 20, 2012 11:29 AM 
    There's a solution if you want to see the PDF inside Safari's window :
    Go to the folder : Your Hard Drive / Library / Internet Plug-ins.
    If you see a file with PDF in its name drag it to the trash.
    Quit and restart Safari to test with a PDF.
    If it works you can empty the trash.

  • Dialog box display won't update after screen blank or being moved

    I have a modeless dialog box used for status display by a plugin I wrote for Acrobat. Everything works fine until the screen blanks or the user moves the dialog box on the screen, at which point no further updates to the dialog box are displayed. My plugin consumes 100% of CPU for long periods of time so the program can appear dead without this display being updated, but nothing I have tried seems to make any difference. The dialog box is generated with ADM and things I have tried include calling "Update" on the dialog box at regular intervals, the windows "Sleep" function to yield the CPU periodically, and a host of similar tactics.
    I'm guessing all the code will get run together once I click submit, but here is how I create the diaglog box (it was working fine without the "WinAppRegisterModelessDialog", but I saw a reference to it elsewhere and tried it to see if it would help, not sure if it actually serves any useful purpose):
    statWin = sADMDialog->Create(inPluginRef, DIALOG_ID, IDB_DIALOG1, kADMModalDialogStyle, NULL, NULL, 0);
    WinAppRegisterModelessDialog((HWND)sADMDialog->GetWindowRef(statWin));
    infoBox = sADMDialog->CreateItem(statWin, 5, kADMTextStaticType, &coords, NULL, NULL, 0);
    // Status header
    coords.top = coords.bottom + 10;
    coords.bottom = coords.top + 12;
    statHeader = sADMDialog->CreateItem(statWin, kADMUniqueItemID, kADMTextStaticType, &coords, NULL, NULL, 0);
    // Status line
    coords.top = coords.bottom + 10;
    coords.bottom = coords.top + 12;
    statLine = sADMDialog->CreateItem(statWin, kADMUniqueItemID, kADMTextStaticType, &coords, NULL, NULL, 0);
    // Progress bar
    coords.top = coords.bottom + 10;
    coords.bottom = coords.top + 15;
    progress = sADMDialog->CreateItem(statWin, kADMUniqueItemID, kADMProgressBarType, &coords, NULL, NULL, 0);
    sADMItem->SetMinIntValue(progress, 0);
    sADMItem->SetMaxIntValue(progress, totalPages);
    // Set window size, and other attributes
    sADMDialog->Size(statWin, coords.right + BORDER, coords.bottom + BORDER);
    sADMDialog->SetText(statWin, PROD_NAME " - Progress");
    // Set header for status line
    sADMItem->SetText(statHeader, " Page # % Complete Estimated Time remaining");
    // Initialize progress bar
    sADMItem->Update(progress);
    Updates are currently performed with the following code segment. The last two lines are my attempts to get the display to update once the screen blanks:
    // show it
    sADMItem->SetText(statLine, textBuf);
    // Update progress bar
    sADMItem->SetIntValue(progress, pagesCompleted);
    // Force display update/refresh
    sADMDialog->Update(statWin);
    // Yield for display update (in case of screen blank or user changes)
    Sleep((DWORD)100);
    Everything works fine until the window is moved or screen blanking occurs, after that nothing seems to work, all updates to the box cease to be displayed. Any suggestions?

    OK guys here's an update. First I went to BIOS and updated the initial display setting to "LCD panel only" from "Auto". At first I thought it helped, because when I worked at the laptop without the external screen attached, the internal LCD panel resumed normally from off (previously this didn't work).
    But today while I was in the office with my external 19" LCD screen attached, and both of them went off after being idle for 10 minutes, the internal LCD panel didn't resume again. So I've tried the Fn + F5 key combination to switch between modes, and I switched from dualview back to single. The internal LCD panel blinked for a second and then turned off immediately, and from that moment on, I was without picture on both of them. SO I ended up hibernating and resuming again. :( An important note - as soon as the computer began hibernating, the LCD went on and I could see the whole progress of hibernation before it turned off.
    Also another note - when I'm in dualview, I always have keep the internal LCD panel as the primary screen. So unfortunately, when it doesn't resume, I don't have access to the taskbar etc to try more things...
    Any more thoughts?
    Thanks again!
    Rado

  • Safari 7.0.6, using Adobe Acrobat 11.0.10, aren't rendering pdf files in the Print Preview screen.  Additionally, only a single, blank page prints for a multi-page pdf document.  Any ideas?

    Safari 7.0.6, using Adobe Acrobat 11.0.10, isn't rendering pdf files in the Print Preview screen.  Additionally, only a single, blank page prints for a multi-page pdf document.  Any ideas?

    Figured it out.  It had nothing to do with the software levels of Safari or Adobe Acrobat.  Here's the fix:
    Open Finder/Applications
    Search "Internet Plug-Ins"
    Move any Adobe plug-ins to the trash
    Quit Safari
    Launch Safari
    Your pdf document should now render in Print Preview and print properly.

  • Printing Selection-Screen while printing ALV Grid output display

    Hi,
    I have a requirement wherein I want to print the Selection Screen also while printing the output in simple ALV grid Display.
    Currently when I print the ALV output report, only the header and the Body of the ALV is getting printed. But the requirement is that I also want to print Selection screen along with this.
    If anyone has faced a similar situation, plz let me know what needs to be done in order to print the selection screen also while printing the ALV report output.
    Rgds,
    Nitin

    Hi,
    You can use given function module to print your
    selection screen
    RS_REFRESH_FROM_SELECTOPTIONS
    >This will get Current contents of selection screen
    RS_LIST_SELECTION_TABLE
    >This will Generates list according to values in selection table(RSPARAMS)
    Sample
    CALL FUNCTION 'RS_REFRESH_FROM_SELECTOPTIONS'
           EXPORTING
                curr_report     = p_repid
           TABLES
                selection_table = it_int_tab
           EXCEPTIONS
                not_found       = 1
                no_report       = 2
                OTHERS          = 3.
      IF sy-subrc EQ 0.
        WRITE:1  'Selection Criteria'(i19),
             /1  sy-uline(18),
             /1  'Variant Name'(i21),
             23  sy-slset.
    *--  This function module lists the Selection Screen contents
        CALL FUNCTION 'RS_LIST_SELECTION_TABLE'
             EXPORTING
                  report        = p_repid
                  seltext       = 'X'
                  newpage       = space
             TABLES
                  sel_tab       = it_int_tab
             EXCEPTIONS
                  sel_tab_empty = 1
                  OTHERS        = 2.
    Mark all helpful answers

  • Fiori Launchpad displays a blank screen

    My Fiori Launchpad displays a blank screen when running the FioriLaunchpad URL
    https://******/sap/bc/ui5_ui5/ui2/ushell/shells/abap/FioriLaunchpad.html
    I installed Fiori and everything appears to be configured ok.  I then installed the backend components for Leave Requests (GBHCM002 and GBHCM003).  I created a new catalog and group in the launchpad designer and assigned them to my role.
    I activated the ICF services, and launchpad services via /iwfnd/maint_service.  Services are assigned to LOCAL system alias and browser calls are successful and I see no errors when testing via the gateway client.
    ZTRANSPORT
    ZQUICKVIEW
    ZPAGEBUILDER_SERVICE_V_0_1
    ZPAGE_BUILDER_PERS
    ZPAGE_BUILDER_CUST
    ZPAGE_BUILDER_CONF
    ZLAUNCHPAD
    ZINTEROP
    ZLEAVEREQUEST
    The following components are installed and I have a combined frontend and backend system running on SAP ECC 6.0 Ehp7.
    SAP_GWFND     740        0009       SAPK-74009INSAPGWFND
    SAP_UI 740        0011      SAPK-74011INSAPUI
    GBHCM002        600        0014       SAPK-60014INGBHCM002 HCM Employee Requests (Leave)
    GBHCM003        600        0012       SAPK-60012INGBHCM003 HCM Manager Approvals (Time, Training,
    UIX01EAP          100         0005       SAPK-10005INUIX01EAP    UI for ERP Central Applications
    UIX01HCM         100         0005       SAPK-10005INUIX01HCM  UI for HCM Application
    UIX01TRV          100         0004       SAPK-10004INUIX01TRV   UI for Travel Application
    I’ve checked ICM logs, ran the cache jobs and authorisations trace.  I’m not seeing any errors anywhere so finding it impossible to troubleshoot
    Please help!
    Thanks
    Amanda

    For Approve leave requests :
    Business Catalog (Launchpad)
    SAP_HCM_BC_MANAGER_X1
    Business Group (Launchpad)
    SAP_HCM_BCG_MANAGER_X1
    PFCG role for Business Catalog
    SAP_HCM_BCR_MANAGER_X1
    PFCG Role for Technical Catalog
    SAP_HCM_TCR_T_X1
    For Employee :
    Business Catalog (Launchpad)
    SAP_HCM_BC_EMPLOYEE_X1
    Business Group (Launchpad)
    SAP_HCM_BCG_EMPLOYEE_X1
    PFCG role for Business Catalog
    SAP_HCM_BCR_EMPLOYEE_X1

  • Transaction solman_workcenter displays a blank screen

    Hi,
    When I execute transaction solman_workcenter it displays a blank screen. There is no error message.
    Is there some setting that is missing.  Please advice.
    Regards
    Phanidhar

    Hello,
    has your user the acording workcenter roles (SAP_SMWORK*)?
    regards
    Christian

  • App displays a blank screen

    The App screen displays a blank screen and does not respond when searching for apps

    Try searching for the name of one of your videos on the iPad's spotlight search screen - swipe your first homescreen to the right, type in it's name, and if it finds it tap on it to see if it plays.
    If that doesn't work then try closing the Videos app completely : from the home screen (i.e. not with the Videos app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Videos app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
    A third option if the two above don't work is a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • Print Webdynpro Screen---INVOICE DISPLAY

    Hi All,
    We have developed a application to create, display INVOICE.
    What client want is now that on our display screen to have a button by which we can give a print out.
    1. I was thinking how to go about it and then  i tested with CTRL + P button and it can help out as it can be useful
    to print the screen.
    2. But how to use this short key on that button ?
    Also is there any better way to do that ?
    *We dont want to use Adobe as we have almost developed the entire app. and just for one print func. we dont want to
    leverage adobe forms.
    Please give your valuable suggestions
    Regards
    Bhanu

    Hi Bhanu,
    As far as I know if you want to print the webdynpro application, then you have to either create Adobe Forms or SMART FORMS. If you go by standard CTRLP functionality, it will only take printout of the visible screen not the entire screen. So if you invoice fits in one screen or page, then you can try with CTRLP.
    I never tried this before but few weeks back I was going through this link. May be it will help you.[ Printing Web Dynpro ABAP Applications|http://help.sap.com/saphelp_nw70ehp2/helpdata/en/f8/872806981d4411b5ce51a00207ed31/content.htm]
    But I would recommend you to go with Adobe Forms for printing.
    Regards
    Abhinav S

  • Photosmart 6510 Printer error/Blue screen on printer display Code:B864F472

    Hello
    I'm having a reoccurring problem with my HP Photosmart 6510 all-in-one. The printer will stay on for about five minutes, give or take, and proceed to flash a blue screen (on printer display) with error code B864F472
    Next the screen displays a "Printer Error" message followed by "Please turn printer off and then on" with all lights on the printer flashing.
    It will display this until I cycle the power and it repeats the same behavior after about five minutes.
    I've searched extensively for a solution and have tried multiple things. Such as:
    -Unplugging from back of printer and wall, 30 sec wait then plug back in.
    -Clean cartridge and print header contacts.
    -Set static IP.
    -Printed various reports from service mode, No errors, Excellent signal strength.
    -Connected to laptop through USB.
    -Partial reset, Semi-Full reset.
    -Reinstalled drivers on all computers.
    -Updated firmware/software on printer itself.
    -Ran HP Print and Scan Doctor.
    -Reset Router
    I'm at a loss now. The unit is just over a year old. I have two laptops and a desktop on the same network. Two computers running Windows 8.1 64-bit and the other Windows 7 64-bit.
    Any help will be appreciated. Thanks in advance.
    -Lee

    I have the same problem. and no solution
    All seems to work before the 5 minuts (I can print diagnostic page from the PC), then I think it a microcode problem ...

Maybe you are looking for

  • Can't duplicate Final Cut Project to La Cie Rugged Triple (1 Terabyte)

    Ok. So I couldn't share/save project to any blank DVDs, and so I bought a new La cie rugged. Now trying to "duplicate" project, but when I go to select the source as the la cie, as opposed to the hard drive, the rugged does not appear as an option. O

  • Enterprise Managers log off each other if they are open in one IE window?

    Has anyone had the same experience? The background is dbconsole is used to manage 10gr1 and 10gr2 standard edition databases hosted on different severs. On one server two db are installed, so there are two dbconsoles. I log onto one dbconsole on my P

  • Stickies Always Rolls Back on Launch

    Every time I quit Stickies and relaunch it, a couple of old notes that I discarded and closed open up again, and none of my new notes open. What's going on?

  • Displaying Process Step in GP

    I have an application that I want to be able to enter a guided procedure process at the exact step that the user left off from.  This would be similar to clicking on an activity in the user's universal worklist.  I am going to have a view created wit

  • Methods... What to do...?

    1. Describe the structure of a typical method making reference to its accessibility, return value, passed parameters, its begin/end delimiters and the method call itself: public void paint (int x, int y) { paint(100, 100); Explain the benefits of enc