My printer no longer connects to wireless router... says it is off-line but the wireless light is on
HP Photosmart C309a
If you reset all settings, that should "forget the network" for you. But when you say that you already tried resetting the settings, were you able to reset them? In other words, were all of the settings reset when you tried it?
Similar Messages
-
I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx, -
Officejet 7310xi All in One Printer no longer connects wirelessly
Hello all,
My Officejet 7310xi All in One Printer no longer connects wirelessly.
The printer does no show up while searching for it wirelessly where it had previously.
In the past it would say that the printer (HP Series 7300) was offline. I would remove the device through the control panel and search again. A printer would be found as HP Series 7300 (Copy 1) . A "ghost" of the original would remain as an offline device. I would default to the new printer icon, Copy 1, and it would work. This happened over the course of a year without any problems.
Now nothing is working. The printer can't be found by my network. I tried downloading drivers, etc. from HP but they either can't download or stop during installation. I don't know if an Windows 8.1 update affected it.
Although the printer has a built in network set up option, it has no installation wizard. I can't find a way to activate the wireless feature/icon. There is no I.P. address either.
I feel like a monkey pulling levers for a banana! I appreciate your help.Hey @Kathlanta ,
Thank you for taking the time out of your day to ask that question on the HP Forums today!
I understand you are having issues with your HP Officejet 7310xi connecting and staying on your network. Going through all of this is making you feel much like this;
By the end of this I want you feeling more like this;
Now let's get to the bottom of this and have some fun doing it! (and no, I have not completely adopted the idea that you are a monkey, but for the time being, seems most fitting LOL )
Ok, so what we are going to start with here is; a full print system uninstall and reinstall and run it through USB to test the printers functionality.
Here is how you uninstall the whole printer software on 8.1 >> Uninstalling The Printer
Here is how you install the drivers offline (use the appropriate links to get your steps) >> Installing HP Printer Software for a USB Connection in Windows 8
You wont need to worry about the wireless right yet until we figure out if the rpinter hardware is ok or not. So sit tight on that portion, I'll get that all back and working later after we figure this stuff out now.
Look forward to hearing back from you! Have a good one!
I worked for HP. -
Would like to print from laptop to printer at home. Printer is ethernet connected to NetGear Router
HP PAvilion dv1000, Windows XP
Would like to print from laptop to printer at home. Printer is ethernet connected to NetGear Router.
I had been able to print wirelessly from laptop to HP 7310 Officejet all-in-one, but now all I get is "document failed to print" message. I can get documents to print on this printer using my smart phone, but not the laptop.
I have used "find printer" button on print screen and can see the printer to select.
Any suggestions?
This question was solved.
View Solution.Figured it out after looking at a few other posts...
Configured port to printer IP Address and now it is printing perfectly.
Thanks for having posts out there to review. -
New Galaxy 5s. Trying to connect to a guest wireless that routes browser to a login screen. The wireless will not connect (gives authentication error), so will not pull up browser window. My previous Android did not have this problem (it would connect and immediately reroute to the login screeen).
Would you please try manually set the DNS address on client NIC to the IP of your server, then try run the connector again?
-
Want to stream Netflix to blueray player via my existing Airport Express wifi. The player finds my wifi but the wireless connection fails - says, " Ensure DHCP server is enabled on router and restart router." I don't think I have a DHCP server. Suggestions anyone?
I can't speak specifically regarding LG, but the Whole Home feature on Direct TV (record a movie on one DVR and watch it on another TV in another location) just won't work with wireless, and I have a strong fast connection at 300 Mbps. Ethernet works perfectly.
Few audio/video products will accept "n" wireless at 5 GHz. I suspect that your LG accepts a 2.4 GHz signal, which would top out at 130 Mpbs.
If you are trying to stream High Definition video, especially at 1080P, my opinion would be that it is unlikely that you will be able to do so reliably using wireless.
Perhaps another user who has figured out how to do this will post with some input. -
Hi
I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?
I have tried reseting the network settings and forgetting my wireless connection and re-connecting to it. I even backed up my phone on itunes and restored it, factory reseted it. Nothing seems to work.
Also after my upgrade to ios 8.1 my personal hotspot option under cellular data has disappeared.
Would you please help me out? I would really appreciate it.Hi..
Restart your router then restart the iPhone to test.
If that doesn't help, try this support article > iOS: Troubleshooting Wi-Fi networks and connections -
Why doesn't my E4200 wireless router show all attached devices when viewing the DHCP Client table?
I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results.
Other than a factory reset, any suggestions to get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago? Thanks!barrysegal wrote:
I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results.
Other than a factory reset, any suggestions to get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago? Thanks!
It is strongly recommended that you upgrade the firmware to a smart wifi, which may resolve lot of bugs. You can also download the firmware here:
E4200v2 Linksys Smart Wi-Fi Firmware11/19/2012
Ver.2.1.39.145204
Download
18.3 MB -
following upgrade to osx 10.8.2 on my mac mini I can no longer connect to icloud, I wouldn't mind so much but I have come to rely on th eicloud services to manage my work and home services, has any1 else experienced this and has any1 any solutions as this is messed up all of my work relations?
Had the same problem this morning after updating to 10.8.2. Mail was finding my dot-mac account as always, but System Preferences popped up and said my iCloud password was incorrect. Did the "forgot password" reset, but still had the same problem. Then I went to icloud.com in Safari, logged in with the new password, it worked no problem. So I went back to the icloud preference pane, signed out of icloud, answered yes to all the warnings about data being deleted from my mac, blah blah blah, then re-signed in to icloud. Everything worked. I did have to set up my icloud account in Mail again, which now lists the account mailbox as "iCloud", and not "mac.com" as it did before. But so far, everything is working (fingers crossed.)
-
I have a net gear wireless router and a APE working great inside the house, but the wireless signal is weak in the backyard, can I get a net gear extender for the back yard and it will boost our wo
Ireless signal and also send my music to the airport express? Or does the airport express work as a stand alone hub?Trust me when I say this coming from 20 years of experience.
Get a powered external drive, format it 1 Partition Option: GUID and OS X Extended Journed as the format in Disk Utility.
Download and install Carbon Copy Cloner, clone internal drive to external drive.
Set a schedule to remind you to do it at least once a week, keep it near your charger.
When you plug your charger in, do plug the clone and power the machine up, set the display to sleep only,
CCC will do the rest.
If you want to boot from it, hold the option/alt and select it Startup Manager.
I've seen many TimeMachine and TimeCapsule nightmares and so far haven't seen a problem from anyone using a bootable clone.
It's simple, it's easy, it's more reliable and more powerful than what Apple does and it only takes plugging in a extra cable.
Make as many clones as you want, keep them time seperated, off site etc. etc.
Cables don't have network issues, clones can be verified in seconds merely by booting from them.
Clones protect your productivity, your up in seconds on a clone despite even the hard drive dying.
Software problem? No sweat, boot of the clone and reverse clone your problems away.
If you want to fuss and muss with half implemented TimeMachine and TimeCapsule network headaches then prepare to suffer.
I don't like to suffer, I bought a Mac not to suffer, but it appears you do with TimeMachine and TimeCapsule.
Most commonly used backup methods -
safari5.1.8 drops off line, but airport stays connected, but window says you are not connected to internet? then a couple minutes later it reconnects. I am on an AT&T wireless.
my mac G4 does not have any problem with this. suspect it is safari, airport never drop off or turn off, just safari
-
Imac works well with ethernet not with wireless - although my other imac work fine w the wireless
imac works well with ethernet not with wireless - although my other imac work fine w the wireless? do i have a prob with a wireless card?
Are the computers in the same place?
You can look around for wireless networks. See:
iStumbler - 98
find AirPort networks, Bluetooth devices, Bonjour services
http://www.versiontracker.com/dyn/moreinfo/macosx/17572
>USB dongle
Newer Technology MAXPower 802.11g/b Wireless USB 2.0 Stick Adapter $15.99 http://eshop.macsales.com/item/Newer%20Technology/MXP2802GU2/
Newer Technology MAXPower 802.11n/g/b USB Adapter. The easiest way to add Wireless Connectivity to ANY computer! 'n' speed is the newest and fastest. $29.99 http://eshop.macsales.com/item/Newer%20Technology/MXP802NU2C/ -
I have the 64bit version of itunes on windows 7. When I connect my iphone5 it says that I don't have the correct software and that I need to install itunes 64bit! And I can go no further! I've uninstalled and reinstalled but it makes no difference. I have no access to other computers so at the moment I don't have a backup for my iphone should anything go wrong.
Please Help!Hello ekbowers,
It sounds like you have installed the 64 bit version of iTunes, but you continue to the get an error message that suggests to download the 64 bit version any time you connect your iPhone 5. I understand that you have already uninstalled and reinstalled iTunes, but sometimes you may need to uninstall additional components related to iTunes to completely remove it from your system.
I recommend following the steps in this article to completely uninstall iTunes:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
http://support.apple.com/kb/HT1923
Once you have completely uninstalled iTunes, you can download the 65 bit version of iTunes for Windows here:
iTunes 11.0.4 for Windows 64
http://support.apple.com/kb/DL1615
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I was in Aussie last month and dropped my iPod Touch (4th Gen) on the road. The screen was cracked on the top left-hand corner (where the wireless area is). The screen got fixed but the wireless stopped working. So I am wireless-less... I bought it last July and its still under warranty, but can I still claim a repair on it?
No because it was physical damage
-
The original 5 meters distance router in WiFi signal is full, but the beginning of the past few days more than 3 meters on the search to the WiFi signal, my own iPhone 5, iPhone 4S received signal is full, only iPad2 searching for less than the signal.
The original 5 meters distance router in WiFi signal is full, but the beginning of the past few days more than 3 meters on the search to the WiFi signal, my own iPhone 5, iPhone 4S received signal is full, only iPad2 searching for less than the signal.
Maybe you are looking for
-
Edition Based Redefinition in Oracle 11g R2
Regarding new feature EBR in Oracle 11g r2 As we all know Editioning view is like a wrapper over the base table which allows each edition to see the table in the form it needs, all data operations will be on editioning view once the view is created.
-
Max. Number of objects in view clusters
Hi, experts: I have a view cluster, which I´m entering several tables related among them in. Point is that when I try to put the table number 16 and activate such view cluster, SAP reports me an error: "Max. number & objects exceeded in view cluster.
-
All but CONTACTS restored. Help!
this is strange. i had synced my phone monday night. on tuesday my phone died and i had to get it replaced with apple they gave me an activated and blank phone, i went home and went to restore it from the backup and after all was said and done it was
-
To "control/select" a group of emails and delete takes forever
when using 'select/control' to group a number of emails for deletion it takes forever to select (7-8 seconds) and to delete takes just as much time. It makes cleaning up email data very troublesome. I have to go to my provider, Windstream, and delete
-
I keep getting a error message "address is not recognized be server"?
I keep getting a error message "address is not recognized be server"?