My problem is bad color on a HP Designjet 90R (Model # Q6656B)

Prints I made yesterday are way off colorwise. They appear mostly orange where there should be no orange. Parts that should be orange are extremely orange. Blues look somewhat purplish. Greens do not show at all.
I thought it might be a profile problem at first and possibly a Photoshop CS5 problem because I have read there are some printing issues with CS5, (this was the first time I printed with CS5) but I printed using CS5, CS4, and CS3. CS5 and CS4 were on a Vista machine, the CS3 on my laptop with XP. I have tried printing with different profile settings including the one Photoshop has defaulted to for years. All the results were bad.
One thing I discovered while poking around the printer was the printhead cover right side hinge is broken. I am talking about the part you pull towards the front of the printer, lift up and then back to release. It wobbles when released and when latched it appears the left side of the cover sits a bit lower than the right side. Could this cause a printing problem?
I'm not sure what else to tell as I am no expert at this.
I would appreciate any help given.
Thanks.
This question was solved.
View Solution.

This forum is focused on consumer level products. For the Designjet you may have better results posting in the HP Enterprise Designjet forum here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

Problems booting Mac color

Hello
Problems booting Mac color
I'm a Mac Pro models: MD 313
System OS: Lion 1.7.4
My Mac Index (before Apple logo) is blue. I need to be gray?
Or has a problem with my Mac?
Please please help? I'm worried.
Please help with your photos.
Thanks

Does it boot?

Printing to an Epson R2880 results in bad color (only from Adobe SW)

I've had a nice workflow that I've used for years. I'm sure many of you would find it a bit tedious and I won't go into the details of it, but the important part is that I always printed out of Photoshop (CS6 Extended - now at 13.0.3 - yes I have the stupid Trial window bug, but that's another matter). My monitors are profiled (no custom printer profiles, but I've downloaded appropriate profiles from PixelGenius for those times when I've needed them, and with my color management my prints have been fairly accurate. I use and Epson Stylus Photo R2880 and I've been very happy with it. I mainly work on a 24" iMac (2009 vintage). Recently I decided to change my workflow entirely based on some of the tutorial videos I've purchased from LL. I decided I was ready to integrate much more LR into the workflow, especially now that it includes soft proofing. Because of the new workflow I was really looking forward to printing out of LR. That should more or less get you current.
To date, I haven't printed with my new workflow and I'd say I haven't printed anything since 13.0.1 on PS and 4.1 on LR (not that I was printing from LR at the time). Having not printed in a while I knew I'd need a head cleaning (sure enough I did) and, as is my habit, once the head was clean, I printed (from LR) a 4x6 of the image I planned on printing at a larger size. It catches any lingering gunk after a cleaning. The print just didn't look right to me (too dark and the colors were a little off). I've encountered prints with bad colors once before and it turned out to be a driver issue. In the process I found a great image that is indicative of some kind of problem and I keep both good and bad prints of it handy... just in case. I decided to print this image, and sure enough it came out looking like the standard craptastic version I was getting with the bad driver ages ago. Just to check out that it didn't have to do with my new process, I printed the same image from PS (which worked fine last time I printed this image). It too came out all wrong (the same all wrong as LR). Since the bad prints looked just like the old "bad driver" prints, I figured I knew what was going on and worked with Epson to reset my print pipeline and reinstall my printers (I also have a Workforce 845 for "throw away" printing and for my wife to use).
With new installs for my printers in place I went ahead and printed again... and again it came out wrong. I was, to say the least, despondent. As a final sanity check I loaded the image up in Nikon Capture NX2 (version 2.3.1) and did a print. All of a sudden the print came out perfect. It matched my old "good" prints and, just as importantly, was a dead ringer for the image on the screen. This is where I find myself. Apparently color management is broken in my Adobe products, but works fine in my Nikon software. I'm at a bit of a loss. I'm 99.999999999% sure that I'm printing out of LR, and especially PS, correctly. Anyone have any ideas? I'd love to be able to print again. Printing out of Capture NX2 is really not a great option.
Thanks in advance,
David

I agree this whole issue is confusing. I have been on the issue (proper printer driver behavior and proper application behavior) using Apple's new print path for a few years now, so I will try to make an attempt to clear up as much confusion as possible.
If drivers and applications are working (written) properly this is how it is supposed to work.
When printer manages color is selected in an application print dialog then all functions of the printer driver are available.
When applications manages color is selected then Color Matching is grayed out defaulted to ColorSync, and the property written print driver defaults to No Color Adjustment (Epson) or No Color Correction (Canon).
See attached examples of both Epson 9600 driver version 8.19 and Canon iPF driver version 2.14.
Epson can and has definitely gotten it right with their latest drivers.
Canon on the other hand uses a special case file (AppColorMatchingInfo.xml) which list the applications that use Apple's new printing path. New application like Photoshop CS5 will need to be added to this file or the driver will default to color management when application manages color is chosen which results in double profiling.
I see nothing that indicates to me that neither Apple or Adobe have problems or bugs in this printflow. Only drivers (and old drivers) that are not written correctly for Apple's new printing path seem to have these problems with double profiling. That being said, do I agree with Apple's approach regarding the new print path? NO. It appear to be an attempt to idiot proof printing using application manages color printing, although it is claimed to be necessary for 64-bit applications. I personally would prefer to use the old print path (like still available in Indesign) where all options are available in the driver regardless of what CM setting I choose in the application print dialog. But it is what it is.
Doyle

Encoding and compression in After Effects (Problems with some colors and some effects))

Hello dear friends,
I would like to export an openning title video for a movie, which is about 2,45 seconds long and 22 GB (Uncompressed)
The footage is 1920X1080.
There are a lot of effects, such as, alpha chanel clips of smoke, explossions and stuff like this.
When I export it into H264, or Mpeg2,4 or avi or H264(blu ray), I get a bad quality encoding in some parts:
I get bad quality in the glow effect I have attached to the titles.
I get bad quality in the clips of smoke (bad color) (tha alpha chanel of the smoke)
Would you hapen to know why only in some parts I get bad quality and not not in the whole footage?
Is it maybe because I chose to export the project only in RGB and not in RGB+Alpha, since my project contains alpha chanel data?
Even if I export the project using Quicktime Animation codec (which is lossless), I get this bad quality (a little better than the previous encodings of course).
I only get a nice encoding when I export the project with Zero compression, but 22GB for a 2 and a half minute clip, is too much...
If somebody has any suggestions, I would be interested....
Thank you!!
Giannis - Greece.

Hello,
I usally export the project totally uncompressed and then I do the final encoding-compression in Adobe Media Encoder but the problem remains.
I have every preferance to "Best" and "High".
Yes, I get artifacts...
About the Gamma problems, where can I select a color profile? In Adbe Media Encoder?
Thank you!
Giannis

Green menubar & "bad" colors in all apps on G5

This problem surfaced when I first installed 10.5 months ago, & persists after fully erasing disk & reinstalling with 10.5.2 -- and did NOT occur under 10.4.x or before.
I have a blue-green menubar at top (main menubar) since 10.5 was installed -- ALSO
All colors in any image viewed -- i.e, .jpg or other photo images in image-oriented app's such as Preview -- will be badly distorted and altered unrecognizably IF the image is viewed at any size larger than thumbnail. Same for iPhoto and other apps, as I said.
Images viewed over the internet are fine, but will lose proper color if downloaded and viewed! Videoconference images with iChat have good color, same for online with Safari and Firefox. However, anything viewed in Preview will open with colors so altered that the image is useless.
HELP!! This makes my G5 useless for viewing "field visit" photos for my visit or any image that's emailed to me. I can't imagine that I'm the only person with this problem, especially since it persisted AFTER I wiped the drive and reinstalled from original 10.5 family-pack installer dvd.
Any guidance, any hope would be greatly appreciated, even via email. First problem that I couldn't solve, ever, in 20 years of Macs, so I'm baffled.

I post this so anyone else going through this will have a hint on where to go to solve it.
The solution was simple: turns out that the display used for this particular G5 had an odd interaction with the Mac's color prefs (and that same monitor works perfectly with all other Macs!)-- I have NO idea regarding cause or in what the mixup is rooted, so if someone at Apple wants more info, contact me! However, simply having the computer boot ONCE with any other monitor causes something in the Mac to reset, and transferring it back to the original monitor leaves the colors set properly, and the problem disappears.
Something very subtle is happening, here -- and someone with more tech and system-software background than I have might want to put some thought into this. It will rear its nasty little head in other situations, I'll bet on that. Feel free to email me if you want more data.
Problem monitor was ANY projection monitor, and in this case specifically a XR-30X DLP projector. Note that this was NOT a problem with simple color-table or color values - everything displays perfectly, even in complex color depth, just fine EXCEPT the color of the menubar and the colors are totally distorted in any image above thumbnail size in ANY image format in any application displaying photo quality images (that draws its color table from the computer rather than from internet instructions). AND note that the projector handles the colors properly when the VGA cable is transferred to it from another monitor, and afterward, so the miscue is happening on the computer end, not in the projector. Only if the computer was booted from the projector does the interaction occur. Get the drift? Thanks! Let me know if more info is useful, and I'll email it or post it here or as instructed.

Satellite M115-S1061 - display issue - bad colors

According to my daughter, her Satellite laptop running XP-SP2 suddenly went dim. At first I thought it might be the backlight inverter so I obtained a replacement but changing that failed to make any improvement.
Experimenting with the display settings it became apparent that many of the display colors were not what they should have been and I began to think something had happened to the LCD or its cabling causing the loss of one of the primary colors i.e.: blue however, upon rebooting I observed plenty of blue from the diplay until XP fully booted.
While changing themes and setting in an attempt to obtain a mere usable display, it became increasingly obvious that there is some type of video inversion going on.
That said, I can find no setting that would could cause this or any similar report of this malady. I have swept for any virus and gone back several restore points with no findings or imprivement.
The driver has not been updated so there is no ability to rollback to an earlier iteration and a search for an update indicates the current dirver is the latest.
Also, as noted, during initial boot-up the display appears to be of relatively normal brightness and the colors are as they should be...
It is not until the XP desktop launches that things go astray.
Any assistance would be greatly appreciated as school is back in session and I either get this resolved and get a new laptop!
TIA,
Bob

Hi
> Also, as noted, during initial boot-up the display appears to be of relatively normal brightness and the colors are as they should be... It is not until the XP desktop launches that things go astray.
According to your description I believe that this might be a graphic card problem.
I would really recommend connecting an second, external display/monitor to this notebook to check if the same bad colors would be visible on the external monitor.
If the same bad colors would appear at the same time on the second monitor then the issue could be really related to a bad GPU chip
In such case a replacement (motherboard) would be necessary
Bye & Greets

Bad color profiles on B8850

posted in another forum but thought I'd try here before I lose my mind trying to figure this out...
I think perhaps my color profiles are bad? Here's the situation:
1) printed a color wheel image on plain paper to test what colors I'm having problems with, and everything looked fine.
2) printed the same color wheel on photo paper and the oranges are just dead, really grey looking, but the rest of the colors are fine.
So, seems like the question is why are my photos not printing correctly on photo paper but do on plain paper? Any ideas or suggestions? Bad color profiles or something for the HP Photo Paper?
I'm losing my mind trying to figure this out. Any ideas are greatly appreciated.
cheers,
Aaron

Every type of paper accepts ink a little differently. If there is a setting that matches that particular paper right in the driver preferences available, I would try that. However, if that is what you are using, then try a different selection, or go into the color management tab (depending on operating system, drivers installed basic versus full) and adjust colors that way to improve the output on that media.
This might offer some additional help:
http://www.hp.com/united-states/consumer/digital_photography/print_better_photos/tips/printer-settin...
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

Problem in BADI, error message not getting displayed

Hello Experts,
I am facing a strange problem in BADI.
The requirement is that the user should not be allowed to change the plant field
on the screen of standard MM transctions for PO/PR amendment.
I have written the code in separate BADIs for PO and PR.
I am displaying an error message if the user tries to change the field.
For PO, it is working fine.But for PR, the same code is not working.
The control is going over to the BADI for PR and rest of the code is working fine.
But the error message is not getting displayed for PR amendment.
Can anybody please suggest the possible cause of problem and some solution to it.
Thanks in advance.

Hi
See the sample BADI code for PR which raises an exceptions and do accordingly
BAdI Name: ZPUR_RFQ (Implementation name) Purchase Requisitions
Definition Name: ME_REQ_POSTED
Interface Name : IF_EX_ME_REQ_POSTED
Implementing Class: ZCL_IM_PUR_REQ
Method : POSTED
METHOD if_ex_me_req_posted~posted .
DATA : v_mtart TYPE mtart.
DATA l_s_eban TYPE ueban.
LOOP AT im_eban INTO l_s_eban.
 IF l_s_eban-estkz NE 'B'.
 CLEAR v_mtart.
 SELECT SINGLE mtart INTO v_mtart FROM mara WHERE matnr = l_s_eban-matnr.
 IF v_mtart EQ 'ZERS' OR v_mtart EQ 'FHMI' OR v_mtart EQ 'UNBW'.
 MESSAGE e000(zm_msg) WITH 'You are not allowed' 'to create PR for stock items'.
 ENDIF.
 ENDIF.
 IF l_s_eban-knttp NE 'F' OR l_s_eban-pstyp NE '9'.
 IF l_s_eban-knttp NE 'A'.
 IF ( l_s_eban-pstyp NE '9' AND l_s_eban-pstyp NE 'D' )
 AND l_s_eban-matnr EQ space.
 MESSAGE e000(zm_msg) WITH 'You cannot create'
 'a PR without material number'.
 ENDIF.
 ENDIF.
 ENDIF.
ENDLOOP.
ENDMETHOD.
Reward points for useful Answers
Regards
Anji

HI YANN/VADIM...Still having problem in BADIs...please help me out

Hi Yann/Vadim,
Facing a problem in BADI can u please help me out...
I am implementing sourcing dashboard.
I am facing problem while implementing the badi BBP_ECS_PO_OUT_BADI in SRM. and BBP_PO_INBOUND_BADI in R3.
i have written following code in BBP_ECS_PO_OUT_BADI in SRM
method IF_EX_BBP_ECS_PO_OUT_BADI~BBP_B46B_PO_OUTBOUND.
data : ls_item type BBP_PDS_PO_ITEM_D.
data : w_customer_fields type BBPS_IF_CUSTOMER_FIELDS_PI.
move 'POITEM' to w_customer_fields-refobject.
move 'CATALOGID' to w_customer_fields-fieldname.
move ls_item-catalogid to w_customer_fields-container.
append w_customer_fields to ct_bapi_customer_fields.
endmethod.
i have created field zsrmcatalogid field in R3 in EKPO table.and i am now implementing the Badi in R3 for BBP_PO_INBOUND_BADI .....in extended classic scenario.
i have written following code in R3 BADI
method IF_EX_BBP_PO_INBOUND_BADI~BBP_MAP_BEFORE_BAPI.
data : wa_customer_fields type bbps_if_customer_fields,
wa_bapi_te_mepoitem type bapi_te_mepoitem,
wa_bapi_te_mepoitemx type bapi_te_mepoitemx,
wa_extensionin type bapiparex.
data : txt_960(960) type c.
read table bbp_customer_fields into wa_customer_fields with key
refobject = 'POITEM' fieldname = 'CATALOGID'.
if sy-subrc eq 0.
move wa_customer_fields-container TO
wa_bapi_te_mepoitem-zsrmcatalogid.
wa_bapi_te_mepoitemx-zsrmcatalogid = 'X'.
endif.
clear txt_960.
clear wa_extensionin.
write wa_bapi_te_mepoitem to txt_960 left-justified.
wa_extensionin-structure = 'BAPI_TE_MEPOITEM'.
wa_extensionin-valuepart1 = txt_960(240).
wa_extensionin-valuepart2 = txt_960+240(240).
wa_extensionin-valuepart3 = txt_960+480(240).
wa_extensionin-valuepart4 = txt_960+720(240).
append wa_extensionin to bapi_extensionin.
clear txt_960.
clear wa_extensionin.
write wa_bapi_te_mepoitemx to txt_960 left-justified.
wa_extensionin-structure = 'BAPI_TE_MEPOITEMX'.
wa_extensionin-valuepart1 = txt_960(240).
wa_extensionin-valuepart2 = txt_960+240(240).
wa_extensionin-valuepart3 = txt_960+480(240).
wa_extensionin-valuepart4 = txt_960+720(240).
append wa_extensionin to bapi_extensionin.
endmethod.
But its not working...
The PO details are not passed from SRM to R3.......
PLEASE CAN U GIVE ME EXACT CODE FOR CHANGES TO BE MADE IN THIS BADI ..AS IT IS NOT WORKING...
Can anybody help me regarding how to debug the BADI in R3.
Thanks in Advance...

Hi Ravi,
You can transfer the standard SRM catalog ID field to R/3 tracking number field (if not already used for another purpose) in the R/3 PO.
This will avoid to implement the R/3 inbound bapi.
Here is an extract of the code.
The ECS PO badi example was here used to transfer the unlimited delivery flag to R/3 PO for a Z combination of criteria as well as the transfer of catalog ID to tracking number field in R/3 PO :
method IF_EX_BBP_ECS_PO_OUT_BADI~BBP_B46B_PO_OUTBOUND.
update unlimited delivery flag in R3 PO for combination of vendor +
Product Category maintained in the bespoke table ZUD_PC_VNDR ..
LOOP AT ct_bapi_poitem INTO ls_bapi_poitem.
 lv_tabix = sy-tabix.
 IF ls_bapi_poitem-po_item IS NOT INITIAL.
 READ TABLE it_item INTO ls_item
 WITH KEY number_int = ls_bapi_poitem-po_item
 del_ind = ' '.
 IF sy-subrc = 0.
Set Unlimited delivery Flag
 read table li_zud_pc_vndr into ls_zud_pc_vndr
 with key partner = ls_partner-PARTNER_ID
 category_id = ls_item-category_id.
 if sy-subrc eq 0.
 ls_bapi_poitem-UNLIMITED_DLV = 'X'.
 endif.
Set the Dummy catalog.. entry..
 if ls_item-catalogid eq c_dummy.
 ls_bapi_poitem-TRACKINGNO = c_noncat.
 endif.
 ls_bapi_poitem-GR_BASEDIV = ' '.
 modify ct_bapi_poitem from ls_bapi_poitem index lv_tabix
 transporting UNLIMITED_DLV TRACKINGNO GR_BASEDIV.
 ENDIF. "READ TABLE it_item ..
 ENDIF. "IF ls_bapi_poitem-po_item ..
ENDLOOP. "LOOP AT ct_bapi_poitem ..
endmethod.
Kind regards,
Yann
PS : please do reward helpful answers ))

Problems with "no color" in the "Fill and Stroke"

I am having problems with “no color” in the “Fill and Stroke” function of Flash CS4 Pro.
I had been using CS4 for 10 days and everything worked fine. Then I tried experimenting with various color combinations (along with “no color”) for “Fill and Stroke” for a simple button. Suddenly CS4 locked up on me while I was working with the “color panel”. A second color panel appeared in the upper left corner and the program was not responding. All I could do was to end the CS4 task.
After that, whenever I created even a simple rectangle, at first the colors would appear as indicated for “Fill and Stroke”, but when I selected the object to see its properties, either the stroke or the fill color box would have a red slash line, indicating a “no color”, and I couldn’t select the color box to change it using the ink bottle tool, although the other box worked fine.
Rebooting did not help. So I uninstalled CS4 (and didn’t keep the preferences), rebooted, then reinstalled it. The problem was still there. Logging on as another user didn’t help. I tried restoring the Windows system to before I installed CS4 and resinstalling it and that didn’t work. I have a disfunctional CS4 now and I don’t know what to do to fix it. Please help me. Thank you.

Have you updated flash to 10.0.2? Have you played around with a bunch of different selections, objects, and so forth to see if this box is always incorrect? I think there's some particular selection (order of selecting things, and so on), where the color swatches in one location don't work as expected. However, it should not happen all the time and from what I recall it was fairly easy to work around (I can't even figure out what this was - so probably not it, as it seems hard to run into or perhaps now fixed).
Also make sure you have the stroke selected - if you don't have everything selected, either the fill or stroke will show no color and dim depending on the selection.

Bad colors in Vim

Hello,
My problem is that colors for Molokai color-schema in Vim doesn't look exactly the same as in screenshot. Molokai isn't the only color-scheme for me that looks kinda weird and I think that's somehow related to terminal support for 256 colors.
I'm using `rxvt-unicode-256xresources` from AUR instead of official `rxvt-unicode` from repo. I have `set t_Co=256` in `.vimrc`. I have Molokai theme for Vim and for terminal (in `.Xresources`) as well, but still it looks kinda different.
http://i.imgur.com/12w08.jpg
Need advice to fix colors, thanks!
Edit: Screenshot shows all correctly (less or more), but actually it's much worse. Weirdly, but taking screenshots somehow fixed it?
Moderator edit: The included image is too big. Reduced to url.
Last edited by bernarcher (2012-12-15 20:08:05)

There appear to be some big differences, to my eye, between the gui colors and the cterm colors.
:hi Function
Function xxx ctermfg=118 guifg=#A6E22E
Color 118 is #87FF00. The cterm color 154, #AFFF00, is a better match to my eye. I edited a copy of the molokai color scheme, and toned down the electric green with:
:%s/=118/=154/g
I have spent some time coming up with a custom color scheme for vim in xterm and urxvt. I now always add this boiler plate to color scheme files so I don't have to remember these useful tips:
" To test, use
" :so %
" To see the current color setting for an individual syntax item:
" :hi Cursor
" To see all the highlight syntax groups:
" :so $VIMRUNTIME/syntax/hitest.vim
" Useful help pages:
" :he group-name
" :he highlight-groups
" Useful plugin:
" xterm-color-table.vim
" http://www.vim.org/scripts/script.php?script_id=3412
" Usage:
" :XtermColorTable
The XtermColorTable plugin works in urxvt. That plugin shows a table in a vim window with the cterm color numbers next to blocks of the color. The display of RGB values can then be toggled using the mouse to select a color block or with single key commands.
Edited for spelling error correction.
Last edited by thisoldman (2012-12-17 11:21:04)

Export Flash image to Illustrator : bad colors and no transparency

I've tried to export my vector work from Flash to
Illustrator.
The result is bad : colors have faded and transparent colors
became opaque.
It is a shame that Flash doesn't provide a correct export
function to
Illustrator now that Flash and Illustrator are both Adobe's
softwares.
Does somebody know a better way or software to export
Flash/SWF vector
images to Illustrator or PDF?
Thanks.
Henri

You may want to follow this thread–no answer so far, but we live in hope…
http://forums.adobe.com/message/2341411#2341411

Need Help Fixing Bad Color Profile (Leading to Bluish Tint)

Hi folks,
I've been experiencing problems with my late-2011 Macbook Pro for the past several months. Whenever it switches to dedicated graphics, the screen results in a bluish tint.
I believe it's a problem with the color profile on my machine. The diagnostic identifies two problems with the color profile, but the system is unable to fix the problem (see attached photo).
Does anybody know how I can fix this?
EDIT: I should note I'm running the latest version of OSX 10.8.4. I never experienced this problem with 10.7.x.

Header message digest (md5) is missing in Colorsync profiles

I am having a problem changing a color in a selected area. Using the Quick Selection tool I am able to select the area I wish to change. Using the Brush tool, color, color mode and click drag in my selected area, nothing happens, no color changes. I hav

I am having a problem changing a color in a selected area. Using the Quick Selection tool I am able to select the area I wish to change. Using the Brush tool, color, color mode and click drag in my selected area, nothing happens, no color changes. I have viewed some videos and read numerous articles but haven't found the one to help me. Please point me in the best direction. Thank you Vincent TC

For the sake of clarity and to save people time, Todd is asking about the behaviour of the Patch tool when using it to repair the area next to the young lad's head. Todd gets a blurred dark tone pretty much regardless of the options he uses.
IMO that's what I would expect to happen because of the close proximity of the other image elements i.e. the lad's neck and the strong lines of his shirt. I would not choose to use the Patch tool in this situation. Content Aware Fill makes a better stab at it.

I wonder about the colors in the program. When i work and later gonna print the text i have some problem. The color is not the same when im print it. One color on the screen and another when i print it why?

I wonder about the colors in the program. When i work and later gonna print the text i have some problem. The color is not the same when im print it. One color on the screen and another when i print it why?

I wonder about the colors in the program. When i work and later gonna print the text i have some problem. The color is not the same when im print it. One color on the screen and another when i print it why?

My problem is bad color on a HP Designjet 90R (Model # Q6656B)

Similar Messages

Maybe you are looking for