My quilt patterns are printing out 1/16 th of an inch too small according to my 1 inch test blocks.

I have a psc 2410xi Photosmart . If the pattern is not exact it will throw the outcome of my quilt off. All help appreciated.

This document is useful in adjusting print output:
http://www.hp.com/united-states/consumer/digital_photography/print_better_photos/tips/printer-settin...
In particular, on the features tab (mentioned in that document) there is a check box for "Print at actual size" which may help in this case.
The size of the margins can make a difference as well, if you are printing something that basically covers the entire printable area, margins will make it smaller to fit.
Settings can be set in the printer driver and in any software that you are printing from.
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

Similar Messages

My CS2 templates are printing out in reverse.

My CS2 Templates are printing out in reverse. All other programs are printing normally. Can anyone advise to clear this problem. Many thanks

Prints pages from last to first:
or if you're outputting film this flips the pages

8.5x11 pages received via email are printing out 11x17???

As of Yesterday (6/24/08), all PDF's that are being emailed to me are printing as if they are 11x17 pages?
The pages being emailed are portrait landscaped, and are 8.5x11 sheets. My print function is set up to reflect this. However, the "preview" on the print function is showing the pages laid out on an 11x17 sheet, so it is taking 2 sheets to print what SHOULD be one sheet. Is anyone else experiencing this?
I have Adobe Acrobat 7.0 Professional.

Its possible you changed the default page setup in your printer driver. Go into the printer control panel in Windows - and check the preferences on the driver?

When I print out photo thru iPhoto, the result is too dark.

Hi all,
I have a problem with printing a photo via iPhoto recently.
I remember when I used iPhoto 9 to print out some of my photos but at that moment the result was pretty OK to me.
However, I don't know exatly when but I guess it could be since I upgraded to iPhoto 10...
Everytime I tried to print out some of my photos from my iPhoto library, the result is way too dark than its original color.
I am using HP Photosmart device(C410ㅁ) with fuji photo papers.
I tried to change several options like color sync or printing quality but NO use!!
Strange thing is that if I use airprint with my iPhone or iPad, color level seems to be OK.
But again, iPhone airprint doesn't give any options to manage printing quality level, it couldn't mitigate my problem, either.
Is there anyone out there who has the same or similar problem just like me?
Please share your knowledge to solve this issues.
Thanks in advance
Luke.

What is the color profile of the photo?
LN

File printing and icons for folders in Bridge CS5 - too small to read

Got CS5 and am trying to use Bridge. The folders are too small to read and the print with them too small. The slider at the bottom of the page enlarges the space but the files and printing stay the same size. If I open one the images will enlarge with the slider but I don't want to waste time opening each file to see what is in them. I want to be able to read wha the file is and open the right one first try.
Tried calling "tech support" Those jackasses can't speak English. On hold for 3 hours overall after getting someone, getting cut off and having to call again. I hope Pakistan nukes India and solves that problem.
When I finally got through the guy told me my Photoshop copy was not registered. Funny, it was last week when it had problems. Then I try changing the pasword and it says it did it, but won't accept it.
I hate computers.
So, anyone know how to get this damn probram to make the folders and printing big enough to read without my having to get up to the screen with a magnifying glass like Sherlock Holmes? The screen is a 22inch graphic arts monitor and I don't have this problem with any other programs. Not Breezebrowser, Not Auto Pano Pro, not Photo Mechanic. Just Bridge with this overpriced and overhyped photoshiz crap.

Small, and uncustomizable, fonts has been a com
plaint in PhotoShop also.
Send in a bug report, they do read those, and maybe if enough users complain they will modify the program.

Print URL at top/ bottom of page is too small & half off the page

I set it to print URL and Title at top of the page, and Date at the bottom of the page. It attempts to do this but the print is verrry small and 1/2 off the page.
Works fine with Google Chrome.
New WF 2540 printer, test page is good.
Mac 10X
Thanks for your help!
Peter

Hi phstol, entering a value in about:config isn't very technically demanding and takes less than 60 seconds. You just need to take a deep breath when you see that long list of settings and focus in on the ones you want to change. Double-click and you can enter a number like 20 or 25. I'd try the top and bottom print edges first and see whether that makes any difference. (Hopefully you have a PDF printer driver so the experiments don't waste too much paper.) Good luck.

Adobe PDF files are printing out smaller than 8 1/2 by 11; only happens on Firefox not IE.

I downloaded the latest free version of Adobe Reader.
Now on Firefox, the page view is surrounded by a black screen. I can increase the view size, and have the document fill the whole page. However, when I go to print, the document prints smaller than an 8 1/2 x 11 page with black space (almost as if I scanned something without a cover) all around it.
Not only is it difficult to read some files, I'm wasting black ink.
I happened to be on another site using Internet Explorer and when I downloaded a file using that browser, everything was normal. No unusual size dimensions, no problems printing.
Seems to be a Firefox issue.
Any suggestions?

You can change the action for Portable Document Format (PDF) from Preview in Firefox to use the Adobe Reader or to Always Ask.
*Tools > Options > Applications
*http://kb.mozillazine.org/File_types_and_download_actions
You can set the pdfjs.disabled pref to true on the <b>about:config</b> page to disable the build-in PDF viewer and use the Adobe Reader instead.
See also:
*https://support.mozilla.org/kb/view-pdf-files-firefox-without-downloading-them

OUT varchar2 param throwing ORA-06502: variable too small

Here's a cut down version of my procedure:
create or replace procedure x(o_log OUT varchar2)
as
v_log varchar2(2000) := 'Starting this log file...';
BEGIN
---do various commands and append to v_log with the results --
o_log := v_log;
END;
When I execute, it works fine until the string gets too large - however, it is nowhere near 2000 chars yet.
Is there a limit on the size of an OUT parameter? Is there a way to specify length of o_log?
Thanks

Hi,
user7724188 wrote:
Here's a cut down version of my procedure:
create or replace procedure x(o_log OUT varchar2)
as
v_log varchar2(2000) := 'Starting this log file...';
BEGIN
---do various commands and append to v_log with the results --
o_log := v_log;
END;
When I execute, it works fine until the string gets too large - however, it is nowhere near 2000 chars yet.
Is there a limit on the size of an OUT parameter? Is there a way to specify length of o_log?
Thanks
v_log varchar2(2000) := 'Starting this log file...';declares v_log to have a maximum size of 2000 bytes. Depending on your character set, that might be less than 2000 chanracters.
The maximum size allowed is 32,767. For longer strings, use a CLOB.
It's up to the calling routine to make sure o_log is big enough to handle the results. Nothing you can do in procedure x can change the size of a variable declared in procedure y.

A serious problem with AAR 5.0 in printing out a book

I have written a book in MS Word 2000 and I converted it in a PDF file with AR 5.0
Then I tried to print it out as a book.
I rotated the pages and included two A4 pages in one so that an A4 sheet to have 4 pages on both sides.
In order to do this trick, I rotated the horizontal text page
to vertical position on the left side for printing out the page 1 and on the right side for printing out the page 2. This must be done in order to have the 4 pages printed out in a sequence and in an A4 sheet.
The procedure is as follows:
First, I print out the page one (1) while having my PDF text page rotated vertically on the left side and the printing out is successful.
Then I rotate again the page vertically to face on the right side to print out the page two (2) in the same sheet.
Here is where the problem begins.
The page 1 is printed out well BUT its top/bottom margin is different than the page 2, which is printed in a lower position on the A4 sheet.
The margins all around the page look perfect but the two of them are printed out with one line lower that makes one page higher or lower than the other and not in a straight line as it is supposed to be.
I have tried to find out what causes this problem with no success so I am into contact with you requesting an immediate help. I know that it is a small but serious problem particularly for my case as an author and I believe that the solution can be given only by an expert of Adobe Acrobat 5.O
Please, inform me about any adjustment that must be done to solve this margin situation (problem) as I know that AAR 5.0 is an excellent software and can do this work for me.
Regards,
Emmanouel

This has nothing to do with Adobe's OpenType development tools, which is the purpose of this forum. I think you need to post this in the Acrobat Windows forum!
Regards,
T

When I attach a file to email, it prints out instead

I'm running Reader on MacBook -- my attachments to email are printing out instead of attaching. . .?

Edit > Attachments > Insert Attachments at End of Message. If a new message is the active window, the option applies only to that message. If you don't have a new message open, then the option becomes Always Insert Attachments at End of Message.

HT1386 I cannot find how to keep previous photo albums loaded on Ipad when syncing new ones with iTunes. The old ones are wiped out every single time

I cannot find how to keep previous photo albums loaded on Ipad when syncing new ones with iTunes. The old ones are wiped out every single time

If it's not too late, see Recovering your iTunes library from your iPod or iOS device. As long as you have a backup of the device when the device still held your photos you should stand a chance of recovering them using a tool such as iPhone Backup Extractor.
tt2

Songs after 7.0.6 update are grayed out and will not play

After I updated to iOS 7.0.6, some of my songs on my iPhone are grayed out and have a red circle with a small red square to their right (similar to the blue version in the iTunes store). When I select these songs, they skip over that song, and two more before playing another completely different song. If I try to play the songs by pressing the red circle/square, they just gray out completely (nothing plays). Two hard resets and a restore hasn't fixed the problem.
Does anyone know what might be happening?

I had this problem too and my roommate solved it!
Go to 'Settings'
'Music'
Scroll to the bottom and enter your password to log onto your home sharing
Then connect to iTunes and sync!

How to find all routes that are going out an interface in IOS-XR.

Hi all,
So if I have the following set up in IOS:
interface GigabitEthernet7/0/0.265
encapsulation dot1Q 265
ip vrf forwarding test
ip address 1.1.1.1 255.255.255.252
ip verify unicast reverse-path
end
ip route vrf Apollo 2.2.2.0 255.255.255.248 1.1.1.2
I can see all the routes that are going out the interface using show ip cef command:
ios-router#show ip cef vrf test GigabitEthernet7/0/0.265
2.2.2.0/29
nexthop 1.1.1.2 GigabitEthernet7/0/0.265
1.1.1.0/30
attached to GigabitEthernet7/0/0.265
1.1.1.2/32
attached to GigabitEthernet7/0/0.265
In case of IOS-XR (ASR9K 4.3.2 or 4.3.1) the same setup and command shows only
attached routes:
router static
vrf test
address-family ipv4 unicast
   2.2.2.0/29 1.1.1.2
RP/0/RSP0/CPU0:TST_riga-sb7-pe-asr9#show cef vrf test bundle-ether2.265
Prefix              Next Hop            Interface
1.1.1.0/30          attached            Bundle-Ether2.2220333
1.1.1.0/32          broadcast           Bundle-Ether2.2220333
1.1.1.1/32          receive             Bundle-Ether2.2220333
1.1.1.2/32          1.1.1.2             Bundle-Ether2.2220333
1.1.1.3/32          broadcast           Bundle-Ether2.2220333
Is there any command to see all the routes that are going out an interface without complicated parsing
of the configuration, recursive show cef commands etc.?

You can accomplish this with the "show route" command. Here is an example:
P/0/RSP1/CPU0:ASR9006-E#sh route next-hop tenGigE 0/3/0/2
Tue Oct 8 15:34:58.046 UTC
Codes: C - connected, S - static, R - RIP, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - ISIS, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, su - IS-IS summary null, * - candidate default
       U - per-user static route, o - ODR, L - local, G - DAGR
       A - access/subscriber, - FRR Backup path
Gateway of last resort is 172.18.87.1 to network 0.0.0.0
D    10.95.248.1/32 [90/128512] via 10.129.56.210, 4d00h, TenGigE0/3/0/2
C    10.129.56.208/30 is directly connected, 4d00h, TenGigE0/3/0/2
L    10.129.56.209/32 is directly connected, 4d00h, TenGigE0/3/0/2
O    10.242.142.240/30 [110/20] via 10.129.56.210, 3d11h, TenGigE0/3/0/2
                       [110/20] via 10.129.56.214, 3d11h, TenGigE0/3/0/3
D    192.168.1.16/32 [90/128512] via 10.129.56.210, 4d00h, TenGigE0/3/0/2
D    192.168.20.39/32 [90/128512] via 10.129.56.210, 4d00h, TenGigE0/3/0/2
RP/0/RSP1/CPU0:ASR9006-E#
Thanks,
Bryan

How can I get text printed out larger? It prints too small to read.

I have an hp psc 1610 all-in-one printer. When I print articles from the internet the text is too small. The options to change size only seem to affect the screen size, not the printer size. It prints fine in my word processor, etc.

File > Page Setup > '''Scale''' <br />
100% or Shrink to Fit is usually the best.
http://kb.mozillazine.org/Problems_printing_web_pages

Printing too small

Hi all.
My printer that is connected to my AE (cannon pixma 4000) is printing everything too small. This is all documents in Word and images in Photoshop. I preview before printing go into every dialogue box available and make sure they are set correctly and still it is coming up too small. I hate having to save everything and open it on the PC to get it to print properly.
This is a recent thing that happened as it was printing the correct size before.
Any ideas folks?
Thanks Alison.

Hi Ish2,
Have you tried shutting down the computer (not a restart) and then doing a Hard Reset on the printer as described in the next link. Click Here After powering up the computer, is there any difference?
If you do a Print Preview, does the page appear as it should?
What is the scale set on?
If you click on Print from the Print Preview window, does that make a difference?
Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
Please select the "Accept as Solution" button on the post that best answers your question.
I appreciate your input ! ___________________________________ _____
Thank You,
Rich
Expert

My quilt patterns are printing out 1/16 th of an inch too small according to my 1 inch test blocks.

Similar Messages

Maybe you are looking for