My recording level wont move

when ever i open GarageBand...it records just fine and everything works. but when i try to play back what i have recorded i can not hear it. iv put every volume on the programe and my computer on max except the recording level. the button on the recording level wont move from zero...why not? i assume that is the issue.

brownboy461 wrote:
Every time i change anything to use a device in this case a microphone insted of using the built in one, i cant hear anything when it plays back.
http://www.bulletsandbones.com/GB/GBFAQ.html#usecomputersspeakers
(Let the page FULLY load. The link to your answer is at the top of your screen)

Similar Messages

I plug my usb shure PG27 into garageband but the recording level gos to zero and will not move!

OK please help, I plug my usb shure PG27 into Garageband but the recording level wont budge and looks like its closed off for anyone moving the level!

wyattcba wrote:
I plug my usb shure PG27 into Garageband but the recording level wont budge and looks like its closed off for anyone moving the level!
http://www.bulletsandbones.com/GB/GBFAQ.html#volumesliderdisabled
(Let the page FULLY load. The link to your answer is at the top of your screen)

Need help with recording level!

Hi,
I am writing a tune on Garage Band. I have recorded several tracks. A few with hardware, a few with soft synths. I find I cannot adjust the recording level with the slider now (soft synth parts only). It seriously needs to be reduced, otherwise it sounds terrible. The slider simply wont move. Something must be wrong. Any ideas?
HELP!

Ratty, at some point you must have set a point on the volume curve by accident, that and/or setting a pan curve point are the only two things that will disable the volume (and pan) controls)
Good to hear the issue is no longer a problem. Have Fun --Hang B-)>

Record level lock on SAP ABAP table editing

Hello All,
I have a requirement wherein I need to give users ability to be able to update contents of a table. Currently, there are using maintenance view on the table for adding/editing contents of this table. However, this prevents other users from being able to enter the table and edit contents of other records within the table.
Can anybody please guide me how do I go about giving record level edit lock on the table instead of entire table edit lock.
Appreciate all responses.
Thanks and Regards,
Samta.

Ok
I have had a request like yours, i.e the users could manage the same table in the same time.
The standard behavior avoids it, because a lock of entire table is set.
This was my solution:
A) I've created a maintenance view for my table, and I set the attibute S (for subset) for all fields will be the key I want to lock.
B) I've generated the maintenance table program for the view above.
In this way if it try to manage the view by SM30, it'll be possible only to indicate the values of the fields for the subset, so not all data of the table will be loaded, but only the records satisfying the key.
C) I've created a program to run SM30 for my view, using the fm VIEW_MAINTENANCE_CALL:
.CALL FUNCTION 'VIEW_MAINTENANCE_CALL'
       EXPORTING
            action      = 'S' "Display mode
            view_name   = <table name>
       TABLES
            dba_sellist = tb_sellist
       EXCEPTIONS
            OTHERS      = 14.
As you can see above, the SM30 is always called for DISPLAY only, in this way no standard lock is set
D) I've use the event 19 in order to change the mode and set my lock:
DATA: BEGIN OF MY_LOCK,
          MANDT       TYPE ZPPTA019-MANDT,
          WERKS       TYPE ZPPTA019-WERKS,
          /TRILOG/SE TYPE ZPPTA019-/TRILOG/SE,
          COD_MOD_TAG TYPE ZPPTA019-COD_MOD_TAG,
        END OF MY_LOCK.
DATA: W_SEL_LIST TYPE VIMSELLIST.
DATA: VARKEY TYPE RSTABLE-VARKEY.
FIELD-SYMBOLS: <MY_KEY> TYPE ANY.
LOOP AT DBA_SELLIST INTO W_SEL_LIST
    WHERE VIEWFIELD = 'WERKS'
      OR VIEWFIELD = '/TRILOG/SE'
      OR VIEWFIELD = 'COD_MOD_TAG'.
    ASSIGN COMPONENT W_SEL_LIST-VIEWFIELD
       OF STRUCTURE MY_LOCK TO <MY_KEY>.
    IF SY-SUBRC = 0.
      MOVE W_SEL_LIST-VALUE TO <MY_KEY>.
    ENDIF.
ENDLOOP.
IF SY-SUBRC = 0.
    IF NOT MY_LOCK IS INITIAL.
      MY_LOCK-MANDT = SY-MANDT.
      VARKEY = MY_LOCK.
      CALL FUNCTION 'ENQUEUE_E_TABLEE'
        EXPORTING
          MODE_RSTABLE   = 'E'
          TABNAME        = 'ZPPTA019'
          VARKEY         = VARKEY
        EXCEPTIONS
          FOREIGN_LOCK   = 1
          SYSTEM_FAILURE = 2
          OTHERS         = 3.
      IF SY-SUBRC <> 0.
        MESSAGE ID SY-MSGID TYPE 'S' NUMBER SY-MSGNO
                WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
      ELSE.
        MAINT_MODE = VIEW_ACTION = 'U'.
      ENDIF.
    ENDIF.
ENDIF.
CLEAR OLD_019.
I hope it can help you
Max

Record Level = Speaker Volume

Currently my record level is equal to my speaker volume. When I mute the speakers, the record level is 0. No record level controls are visible. How can I fix this?

Del Capslock wrote:
-r in the shortcut target box made no difference. Still no record level controls
In the Audio Mixer, the slider for speaker volume moves in tandem with the Audition slider. They cannot be controlled independently.
It should be .exe -r (with a space). If you can't get record options at all, then something weird is going on, and we'd need to know more about your particular PC or laptop.

Recording Level Low in Garage Band, Avid mBox mini, NT2

HI there,
I have setup a home studio. I have a MacBook Pro connected to Avid Mbox Mini Soundcard, two speakers and a Rode NT2 condenser mic.
For some reason, the voice or acoustic recording level is very low...I can still record but the sound level is very low and if I increase the input volume then there is a terrible echo...I am sure there is something wrong.
These are the solutions I have already tried:
- System preferences, I put the input as Avid Mini...and activate +48 button to power the mic.
- Garage band, I move track volume to track pan, Monitor ON, 24bits...and the Recording Level is gray-out since I am using an external sound card (I assumed because of what I read).
Any idea on how I can solve this issue, I am sure there is something wrong, the mic and soundcard can record this bad.
Thanks in advance. Mariano

Hi, thanks very much for your reply gjmnz...I finally went to Virgin like 7 times...during the same day...to figure out what was the issue...and here is what I have learnt:
- The memory of the computer is very sensitive to recording, that is why I read some blogs saying that the mic is unstable, some times is picking up and sometimes is not...for instance I was using Torrents at the same time so the pick up was horrible...over time. Because the torrent and internet connection was eating my memory, event though I have 8gb
- The other thing I learnt and I agree with you (thank you) is that you shouldnt be paying much attention to the leds levels in GB...that will miss you, you have to test and try different gain levels.
- The last thing and what solved my problem, was to buy an analog mixer console for the mic to enhance the picking...And now it is working properly to the point that now it makes senses to use the lower of the Dbs...the NT2a has -4 or -8 for ambient noise cancelling...
Conclusion, for me at least...if you bought a Avid Mbox mini and you have a Rode Condenser mic (NT2a or NT1000, I tried both) the only way to enhance the capturing of the mic is to get a mixer console...
This is the one I bought http://www.mackie.com/products/402vlz3/ (it is ok...but works for home recording).
Hope this helps the rest...I read that the low volume issue is being around since 2007...and I saw a lot of question unanswered...
Best, Mariano

Rented a movie and paid for it, cost was deducted but no record of purchasing movie anywhere

rented a movie and paid for it, cost was deducted but no record of purchasing movie anywhere

did you download it? it wont show up unless you do

Record Level Adjust for Audio in Voice Memo or Video Recorder

I would like to request that Apple allow me to adjust the record audio volume level when recording in Voice Memo or Video Recorder modes. Often I find that the audio is distorting and most times I cannot step back far enough to avoid distortion levels. While I love the ability to SEE the audio level in Voice Memo mode, I am hoping that it is only a matter of firmware upgrade to be able to ADJUST the record level.
Also, if it is possible, it would be great to see some indication of audio level when recording video... something simple like a bar graph with green, yellow and red bars with the highest level reached sticking for a few seconds so that I can tell what the level is.
An alternate solution (if none of the above is possible in a firmware update) would be to automatically adjust the recording level to prevent audio distortion.
Thanks for the great iPod and here's hoping for a great firmware update in the near future!

Thanks, I've submitted my recommendation to Apple.

Audigy 4 Pro Low Recording Levels/Master Knob/OSD probl

I purchased a second-hand Audigy 4 Pro. I was not given the software disk but managed to install the latest drivers and get it to play MP3s. I use Adobe Audition to record my old tapes to MP3 and record my attempts at guitar. With my SBLi've I had no problem. I bought the Pro because of the ease of using the breakout box. However I have some quesions about some problems I am having. ) Since I have no Creative software, just Win XP Mixer I don't seem to be able to control the input levels from either the mixer or the box. I have a tape deck using RCA to Line In 3 and an electric and acoustic guitar to Line In 2. The mixer record levels seem to have no effect. I can record but nothing seems to be much more than -20db or so at most. Could this be because Adobe Audition only shows Line In 3 L (ie one channel only)? Could this be because of the much greater dynamic range of the Audigy 4 compared to the SBLi've Value? Do I need additional Creative software and if so what and how to get it please?2) The Master knob on the breakout box just spins round and round without sto
ps.
In other words you can rotate it in either direction ad infinitum. Is this correct? Pushing it in and out does cause the mute to work fine. 3) The help file talks about an On Screen Display associated with the remote. I don't have one when I use the remote, even when I press the Display button. Again, do I need Creative software for the remote? I have a yellow question mark against Multimedia Audio Control in my device list. ThanksMessage Edited by Dunkelmann on 2-23-200607:22 PM
Message Edited by Dunkelmann on 2-23-200607:43 PM
Message Edited by Dunkelmann on 2-23-200608: PM
Message Edited by Dunkelmann on 2-23-200608:5 PM

Wow these forums still suck. You have easy questions and no one bothered to help you out. I registered jsut to answer them for you although you probably already figured it all out. . It seems that loudness is optomized by creatives own drivers. What you described was also true back when you could use the e-mu driver hacks before creative bought e-mu. 2. The master knob indeed spins for infinity, obviously with no effect once you get to either end. This sucks becasue i have OCD and constanly spin this thing all kinds of ways. THey should have used the same system as the line-/mic knob. Only God and the engineer will ever know why they did this. 3 Yes. The on screen display is pat of the creative media player app.
So to solve all your problems, you can get the full software package from creative.com under the support menu. Just follow the menu options for your device. The software requires that you have the hardware which you do so the software is free. One more problem you WILL have. The software doesnt install under XP. You have to enter windows safe mode and install it from there otherwise the whole thing freezes up during the start of the install process. Fun times!

Any option to restrict SE16 record level access based on company code?

Hi All,
I have a requirement to restrict record level access in SE16 based on company code.
Our SAP system has two company codes. The requirement is that users of one company code should not be able to see records of other company code in SE16.
Is it possible through some exits/badis/other methods?
Thanks in advance.
Regards,
Arun Mohan

You could write a small front end that accepts the company code, applies custom authorization code for each value and retains or removes, then calls the transaction and enters the selections the user requested and that your authorization check resulting in "passing".... Of course, you'd have to block those users from "pure" SE16... I once worked in situation similar, users in one country couldn't see USA data, etc. I think someone wrote an entire new program, called by ZSE16, for that.

I have my new music which i downloaded in my itunes library but when i go to move it to my iphone music folder it wont move and a red circle appears?

i have my new music which i downloaded in my itunes library but when i go to move it to my iphone music folder it wont move and a red circle appears? i have tried all different copy and paste but it still doesnt work

Drag and drop only works if "Manually manage music" is selected on the summary tab in iTunes.
Instead, use the Music tab and playlists to manage what content is on the device as described in the User's Guide.

Recording Level Sli

I have the X-Fi Fatality sound card. For some reason, (and overnight), the recording level slider won't function any more. The message in the recording status window says "Follow Mixer Settings". I don't want that!? I want to be able to control the recording level from the player window as I always have. Does anyone know how to turn off the "Follow Mixer Settings" option? Thanks!

Found the answer. For some reason, the "Sound & Audio Devices" in Control Panel didn't have the "Use Only Default Devices" checked. This was because I installed a Logitech HD WebCam, with its own microphone. That little check box somehow got unchecked. Not only did this fix the problem, but it also fixed "Smart Recorder", which was telling me that I didn't have an audio device. Everything's good now.

Line In Recording Level Adjustment

I am recording from a tape recorder to the hard drive. I have done this a lot over the years. Suddenly I am no longer able to adjust the line in recording level. I have always before gone to Control Panel/Hardware and Sound/Sound (recording tab), Click Line In, then click on Levels. When I adjust the level, either lower or higher, it does nothing to change the sound level. Can aynone please tell me why this feature isn't working any longer on my computer. Could some other setting have gotten changed? Where should I look? Thanks!!!!

Have you tried to discuss it with mixer manufacturer?
I mean they know own product very well and have best experiences with it.
I presume they have tested it on different hardware platforms and different operating systems so I believe they are the right address where you can ask for help.
In control panel you have standard options for sound but maybe you need something specific for connected mixer.

Recording Level?

New to Logic, coming from garageband and I have a quick, probably embarrassingly easy question, but in Garageband when recording from an external mic there's a slider that can set the recording level, to prevent clipping. Is there a way to do this when recording into Logic? Thanks.

No. This would only be a problem if you are plugging a mic directly into the computer (you're not doing that, are you?)
Any external audio interface you might use would have a level control. If you have not yet thought about getting an external interface, I suggest you search these forums for suggestions... there are many threads about this. I assume that you have upgraded to logic to have more control over your music than garage band will allow. As part of that process, a decent interface would seem mandatory (and a decent mic, of course... there are also many threads about this)
And in any case, when you're setting the level, you need to do more than just avoid clipping. Assuming you are recording in 24bit mode (you are, aren't you?) it makes a lot of sense to set your levels so that they are peaking at least 6 - 10 db below max. This doesn't look as pretty on the meters, but by the time you put them through a number of plugins and send them all to busses and outputs, that extra headroom will really open up your recordings so they don't sound so digital and squashed. There are also many threads about this.
Welcome to the big bad world!

Change the recording level for recording with Thunderbolt-Firewire-Mixer

Hey,
I just bought a PHONIC Helix Board 24 Universal for recording some music via Firewire.
Because my IMac has no Firewire-slot, I am using a Thunderbolt-Firewire-Adapter and a Firewire 400-800 cable.
If I try to record some music it sounds really horrible.
It seems that the reason is the recording level which can be changed while using the internal micro but not with firewire-Thunderbolt.
The recording level is set on max, resulting in overmodulation and noise.
Is there any way to adujust the recording level?
Thank you in advance!
Kay

Hello Jshen6,
Have you tried looking at the examples in LabVIEW under Hardware Input and Output>>Synchronization? The Analog Input-Synchronization.vi example shows you how to synchronize AI across multiple devices in various configurations and for various types of hardware. Would you mind listing what hardware you are using? Are all three devices taking the same data (voltage, strain, acceleration, etc)?
Jonathan L.
Applications Engineer
National Instruments

My recording level wont move

Similar Messages

Maybe you are looking for