My restrictions passcode will not work after downloading the latest update

After downloading the most rescent update, I could not go into my restrictions and make changes.  Passcode failed.

So, you've forgotten your restrictions passcode.  Next step is to reset your device to factory settings.

Similar Messages

  • My itunes stopped working after downloading the latest update.

    what do i need to do to get my itunes working again and how do i get my library back?

    (A) Reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.
    (B) Reset all settings
    Settings>General>Reset>Reset all settings
    Note: Data will not be affected but settings will be reset.

  • HT201263 My computer will not let me download the latest itunes, is there a way to restore ,y ipad2 without the latest itunes version?

    my computer will not let me download the latest itunes, is there a way to restore my ipad2 without the lastest itunes version?

    You don't provide enough info to answer.
    What computer model and what operating system?
    What version of iTunes is currently installed?
     Cheers, Tom

  • After downloading the latest update, my playlists now go into shuffle mode everytime I try to play.  I have turn6ed off shuffle on both my computer and ipod, and even tried recreating a new list, to no avail.  Any ideas as to what may be causing this?

    After downloading the latest update for my Ipod touch, my playlists now go into "shuffle" mode everytime I try to play.  I have turned off shuffle on both itunes and my ipod and even tried recreating the playlist and syncing with no luck.  I don't know what is causing this, because before the last download, it never happened.  Any ideas on how to fix?

    Since this is an XP machine, which version of iTunes do you have installed?  Is it the latest version?
    Have you tried starting iTunes, attach the USB end of the cable, then while holding the home button on the iPod connect the 30-pin connector end of the cable to the iPod...that is the recovery mode but also should make iTunes see the iPod.
    If that doesn't work you may need to take the iPod back and have it tested by the genius bar techs to make sure the connector is not bad.

  • After downloading the latest update IOS.8, for my IPad the Backup

    After downloading the latest update, IOS.8 , for my IPad the Backup  and Storage option under settings is no longer there

    The iCloud backup option has moved - it's now Settings > iCloud > Backup (it's towards the bottom of the list of items to back e.g. photos, mail, contacts, calendars ...  Backup, Keychain, Find My iPad).
    The storage option is Settings > iCloud > Storage (above the list of items to back up)

  • After downloading the latest update my pc has no sound at all, can anyone help?

    after downloading the latest update my pc has no sound at all, can anyone help?

    Try reading the suggestions here: http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/

  • After downloading the latest update I get "an unknown error occurred (-42110)

    After downloading the latest update I get "an unknown error occurred (-42110) does anyone have a clue? I can get to the store just fine. Everything seems to be playing fine. The error comes up everytime I load iTunes.

    Removing the SC Info folder as per the "Error 3001," "-42110," or "5103" section in the Specific Conditions and Alert Messages: (Mac OS X / Windows) section of the following document seems to help most folks reporting the iTunes launch 42110s:
    iTunes: Advanced iTunes Store troubleshooting

  • I get an error message after downloading the latest update. It says to download only and then to install manually. How do I fix this?

    I get an error message after downloading the latest itunes update.  It says to download only and then to manually install. How do I do this?  Or, is there some way to make the download work?  Thank you.

    The message is 'errors have occurred, go to tools>download only and try installing manually'.  BTW, I am using Google Chrome.

  • After downloading the latest update when I sync my phone my contacts don't appear, help!

    After downloading the latest software update I connected my iPhone and afterwards found everything but my contacts transfered over so I don't have my contacts on my phone where I need them! Can anyone help?

    It's a problem with Gmail. There is another thread discussing it, but most would rather whine than try to fix it.
    Nobody has figured out what is causing it, but there have been various suggestions.
    One was to display the All Mail folder if you've hidden it.
    You can delete by opt- delete. I think that will delete it immediately.
    Another person looked in the user/Library/Mail/V2/ folder.  He had duplicate account folders, having a sequence digit suffix.  He deleted the duplicates and it fixed things.

  • Youtube HD won't work after downloading the latest version of Flashplayer (11.9.900.117)

    I have a windows Vista, system: 32 bit, and I downloaded the latest version of adobe flash player (11.9.900.117)
    But since I did this I can no longer watch youtube vids on HD with internet explorer.
    They open with a low quality like 360 and when I want to put them on HD the vid just stops working, however if I go to watch on google chrome it will work normal, why is this?

    Enveena wrote:
    I have a windows Vista, system: 32 bit, and I downloaded the latest version of adobe flash player (11.9.900.117)
    But since I did this I can no longer watch youtube vids on HD with internet explorer.
    They open with a low quality like 360 and when I want to put them on HD the vid just stops working, however if I go to watch on google chrome it will work normal, why is this?
    Chrome has its own Flash Player Plugin ("PepperFlash"). It works independent of the ActiveX Flash Player Plugin in IE.
    See:ActiveX Filtering in Internet Explorer  to make sure that ActiveX controls aren't blocking ANY feature that Flash Player can access.
    If that fails, I'd recommend moving to Firefox, as Chrome is an extreme rexource hog and will eventually grind your system to a halt if you get enough tabs open.

  • HT1338 I am not able to download the latest update or any update period on my ipad2. Please help

    Please help me install the latest update for my ipad2. I have an iPhone 4s so I know how to install and update but I am not able to do the same on my ipad2.

    You posted in the OS X 10.3 forum instead of the iPad forum. To get answers to your question, next time post in the proper forum. See https://discussions.apple.com/index.jspa  I'll request that Apple relocate your post.
    If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 6.1.3. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
    iOS 5: Updating your device to iOS 5 or Later
    http://support.apple.com/kb/HT4972
    How to install iOS 6
    http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
    iOS: How to update your iPhone, iPad, or iPod touch
    http://support.apple.com/kb/HT4623
    If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
    Tip - If connected to your computer, you may need to disable your firewall and anitvirus software temporarily.  Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 6.x, the next update can be installed via wifi (i.e., not connected to your computer).
    Tip 2 - If you're updating via wifi, place your iPad close to your router to preclude getting a corrupted download.
     Cheers, Tom

  • My iphoto will not work after downloading iphoto library upgrader.

    I have a new macbook and just tried to use iphoto and it told me I had to download the iphoto library upgrader or quit. I downloaded it but still can not open iphoto.

    You have to download and RUN the iPhoto library upgrader - if and only if your old version of iPhoto is iPhoto '08 (version 7.x.x or earlier) - and as always backup your iPhoto library prior to any update or upgrade in case of problems
    LN

  • Exchange email will not work after IOS 5.1 update. Anyone else having same problem. Its been three days now I cannot get mail.

    Exchange Email not working on Iphone 4S is anyone else having the same problem and is there a fix for this?

    @ w3nitro
    I'm having the same issues, except only one of my Exchange accounts took a dive after upgrading to iOS 5.1.  My Gmail account (set up as Exchange) works flawlessly but my native Exchange account (work e-mail) stopped working after the update.
    Post update to 5.1:  (work Exchange account) I could view my inbox and view individuals emails in the inbox, but I was unable to send any emails.  Mail started asking for my password after the update (for the affected Exchange account) but once entered, it failed to verify.
    I completley removed the Exchange account and rentered all the account settings but again, failure to verify any information.  I was hoping my password might have changed but it did not.  Also, maybe the IT guy at the office (not very bright) changed some settings but the only difference is the new iOS update.
    And while playing with the iPhone trying to make it work again, I noticed something really weird.  Old emails (2-3 weeks) from multiple email accounts to include the inop Exchange account started showing up again on the pull down notification menu.  I would clear these out of the notificaion menu but they always kept reapearing; very strange. 

  • My serial number will not work after using the trial, I purchased the software from Best Buy.

    Adobe Premiere Elements 11  I have uninstalled and reinstalled, but still will not accept serial number.  Please advise

    lindawhitssitt
    Please use the following link to reach Adobe Chat with your serial number issue. You should get immediate and effective resolution to your issue. After the link opens, click on "I still need more help." and the Adobe Chat pop up will appear.
    http://helpx.adobe.com/contact.html?product=premiere-elements&topic=serial-number-issues-o r-activating-my-product
    Please let us know the outcome.
    Thanks.
    ATR

  • After downloading the latest update, Firefox starts but is not responsivc

    Mac Version
    When I opened Firefox a message appeared that an update was available. Soon there after another message appeared that said and error occurred while attempting to update. It was suggested I download the update manually which I did.
    After the download was complete, I tried to open Firefox and it opened with all of the menu items showing but the browser window was blank. (I had Google as my home page)
    I could click on all the menu items but nothing dropped down.

    It's possible that you are having a problem with some Firefox add-on that is hindering your Firefox's normal behavior. Have you tried disabling all add-ons (just to check), to see if Firefox goes back to normal?
    Whenever you have a problem with Firefox, whatever it is, you should make sure it's not caused by one (or more than one) of your installed add-ons, be it an extension, a theme or a plugin. To do that easily and cleanly, run Firefox in [http://support.mozilla.com/en-US/kb/Safe+Mode safe mode] (don't forget to select ''Disable all add-ons'' when you start safe mode). If the problem disappears, you know it's from an add-on. Disable them all in normal mode, and enable them one at a time until you find the source of the problem. See [http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes this article] for information about troubleshooting extensions and themes and [https://support.mozilla.com/en-US/kb/Troubleshooting+plugins this one] for plugins.
    If you need support for one of your add-ons, you'll have to contact its author.
    If the problem does not disappear when all add-ons are disabled, please tell me, so we can work from there. Please have no fear of following my instructions to the line, as all can be easily undone.

Maybe you are looking for

  • Dynamic SQL Error -ORA-00904: invalid identifier

    Hello! I'm really hoping I can get some fast help on this. In the interest of honesty, this is for a university oracle programming assignment. I've searched everywhere I can for the answer and haven't had any luck. Anyway, the problem in a nutshell.

  • BPM Process and Task Flow association

    Hi, I deployed one BPM process on a partition called "common". It has a human task, so when I am deploying the human task as separate adf ui project, do I need to specify the partition in hwtaskflow.xml as hwTaskFlows xmlns="http://xmlns.oracle.com/b

  • Acrobat X Pro will load one file, but crashes when loading a second file

    This problem has existed since upgrading from Master Suite CS5.5 to Master Suite CS6. It will open a new file, but not a second, any attempt to do so causes it to crash.  Hence, requires it to be exited and restarted and only then will open the desir

  • STO (plant to plant),stock in receiving plant shown in on-order stock

    STO plant1 to plant2 ,I have created PO and done delivery in VL10G ,stock is transferring from  plant 1 unrestricted use stock to plant 2 on-order stock instead of unrestricted use stock.. kindly suggest.. vipin

  • Printing elements of a table

    I've got the printing problem fixed but I'm trying to print elements of an array onto paper. It keeps giving me an unclosed character compiler error. Am I using the wrong method? class PaintCover implements Printable{ Font fnt = new Font("Helvetica-B