My s930 won't charge. need help
i've been using my s930 for 1,5 month when it suddenly wont charge anymore. the red light is on but it wont charge. it just stopped at 4 percent. i tried calibrating the battery but it still wont work. any suggestions? thank you for your time
Faulty battery maybe? Try to replace it with another one and try if the same happens.
Lenovo G550 + Lenovo S930 + Lenovo Yoga Tablet 2 - 10"
Similar Messages
-
MacBookPro Charger Won't Charge. Help?
Okay, so I have had my MacBookPro Laptop for about a year now, and just this last week the charger has been acting up. It charged when I used a different outlet, now it won't work at all. Even when the battery is at 19% it won't charge, and in the corner where the battery is shown, it is probably bugged because it says the power source is the adapter, but when the adapter isn't even in my laptop, it still says it is charging. I don't know what is the problem, but it I need it fixed as soon as possible. Help me please?
Try resetting your SMC;
http://support.apple.com/kb/HT3964
Also, read here:
http://support.apple.com/kb/TS1713 -
Hard Drive icon missing - Desktop folders won't open - Need Help!
I need help! I have a 400 MHz PowerPC G4 with 768 MB SDRAM, no DVD drive - was running OS X 10.3.9 quite happily. We became owners of a new iPod Nano - so we had to upgrade to 10.4.
(I'm writing this on my 800 MHz PowerPC G4 with 768 MB SDRAM, (also no DVD drive) that I upgraded from OS X 10.3.9 to 10.4.11 without incident.)
Installed 10.4 using a FireWire Hard Drive - installed software updates to 10.4.11 - ran Disk Utility - ran MacJanitor - ran DoktorKleaner - everything was working well.
Rebooted and the Hard Drive Icon had disappeared from desktop. Folders on desktop have all lumped together in the top right hand corner of the screen, and refuse to open.
Only programs in the dock still work - clicking on the Finder icon only gives the option to hide. New Finder Window does not work. Programs can be found in Spotlight, but if they're not in the dock they won't open. Trash won't open or empty.
I attempted to reinstall Mac OS X using FireWire, but now the Hard Drive is full and is telling me it will erase and reinstall. I need to save files off this computer now (Sadly no backup exists) before my wife readies divorce papers.
I tried using FireWire Target Disk Mode to copy files - with the 400MHz as Target I just get a spinning Beach Ball any time I click on the Icon. After far too long it opened up an empty window.
With the 800MHz as the target, the 400MHz does not show it on the desktop, so I have no way of copying files to it.
Anyone have some advice that doesn't involve a time machine?Whenever something starts going wrong with the computer I suggest you first boot from the installer disk, select language if applicable, choose utilities, run Disk Utility and verify (and repair if necessary) the drive. Then repair the permissions on your computer. You can also repair permissions from DU on your main drive while booted, but to properly verify and repair your drive you have to run it from a drive other than the boot drive.
[Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
[Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
[Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
From BDaqua (couldn't have said it better):
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Then Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes."
A few questions:
Was this a retail installer disc that you used to do the upgrade?
How much free space do you have on the computer?
Did you use the [PPC Combo updater|http://www.apple.com/support/downloads/macosx10411comboupdateppc.html] to get to 10.4.11?
Did you do all these updates in one single session or restart and check your computer had accepted them okay between each update? It is critical to repair permissions before and after each update otherwise the installers won't install fully and you end up with a mix of versions.
You can set the Finder Preferences, general, to display a hard drive icon, but it sounds like your problems are going beyond that?
You can also try trashing your Users -> home folder -> Library -> Preferences -> com.apple.finder.plist file and see if that clears up the issue. That sets the Finder preferences and if it gets corrupted it will cause Finder problems. -
My iPhone 4 won't charge anymore, Help!!!!
Help!!!! my iPhone 4 won't charge anymore.. my iTunes doesn't even recognise it anymore, I've tried charging it from my computer and from the wall but nothing... don't know what to do. It was charging this morning but then i tried this afternoon and nothing happened, i really don't know what to do
Hey nankhalifa,
These are the recommended troubleshooting steps for when your iPhone isn't charging:
Important: Only original iPhone can be charged from a FireWire-based power source. If iPhone is connected to a computer that's turned off or is in sleep or standby mode, the battery may drain.
Verify that the outlet being used is working.
Try another USB power adapter if available.
If no other USB power adapter is available, try connecting to a high-power USB 2.0 port (not a keyboard). The computer must be turned on and not in sleep or standby mode.
Try another USB cable if available.
Also refer to iPhone and iPod touch: Charging the battery.
Welcome to Apple Support Communities!
Sincerely,
Delgadoh -
Exchange Active Sync won't work need help
I have been reading a few dozen of these post that people are having issues with there iphone sync with exchange. I am TOO!.
For some i can get into owa and from the iphone safaria.
The iphone was able verfy the ssl certificate, but nothing is syncing with mail server
My network infrastructure.
1. Clustered mail server . Running exchange server 2003.
2. firewall- port 443 has been verified to be open and able to acces owa from iphone safari
3. I have NO isa setup in my network.
4. Called SSL verisign company and everything checked out to be fine.
5. virtual folders have been verified to be correct.
6. checked dns report no errors.
7. AD exchange feature mobile services and protcols was verfied to all on.
8. turned off wifi
9. checked all creditals.
And it just won't push anything. I have come to the conclusion that is either IIS or Iphone is using a multiply protocol ports to access the exchange. But i don't know i need HELP
Simple troubleshooting steps to start with:
1. Check your version of Exchange. Must be at least 2003 w/SP2.
2. Check your security certificate. If you go to your "https://webmail.yourdomain.com/owa" or "https://webmail.yourdomain.com/exchange" and receive a certificate error, you may want to look into an external certificate from a recognized CA. I used SBS through my registrar.
3. Check to ensure your "Front-End" and "Back-End" server are not both requiring SSL. That will cause issues with OMA.You don't want to check OWA (Outlook Web Access) as it is a full mail client for a notebook or desktop.
The iPhone uses ActiveSync OMA for syncing. Thus, you want to check https://www.domain.com/OMA (where www.domain.com is the URL to the Exchange server - same URL as the OWA url) with a notebook or desktop. The "s" in https is needed at OMA requires SSL.
You should see a login prompt for username and password followed by a list of Inbox messages. If you don't, the server is not correctly configured for OMA.
Once OMA works from a desktop or notebook, it is an easy procedure to add an Exchange account to a phone. Just follow the iPhone on screen examples and provide only the path to the Exchange server and not the "/Exchange" following.
This information can be found on many threads in this forum using the Search feature. -
My iPhone 4 won't charge. Help!
I took my iPhone4 off charge last night to use it and when I put it back on it only acknowledged that it had been plugged it and vibrated, it didn't actually charge at all. I have tried connecting it to my dock and my MacBook also and it's the same story. I tried to turn it off and on, left it to charge overnight and did the home/sleep button reset. Nothing's worked and now it's completely dead.
Each time I plug it in it will bring up the apple sign and turn on but since it won't charge it shows my home screen for a couple of seconds and turns straight back off. Please help!Pretty certain the battery's dead and can't hold its charge anymore if the phone wasn't physically abused.
Time to take it in for its regular battery replacement. Would recommend to back it up first, but that is gonna be difficult, so good luck and hope you don't lose all your stuff. -
IMac G5 won't bootup, need help, Cap't J is in trouble!
Alright, Cap't J is in trouble, needs a commander.
My iMac G5 won't bootup.
I can hear the fans loud.
need help please!Have you tried http://support.apple.com/kb/TS2094 ?
Also, before going to step 5 and taking a screwdriver to it, try:
Powering up with Option held down
Booting from an install DVD with C or Option held down
Booting from an install DVD into Apple Hardware Test by holding D down -
Updated to Mavericks now my Toshiba External HDD 3.0 won't mount need help what to do
I recently updated to mavericks now my toshiba external hard drive wont connect and i have some important data need help to get drivers im assuming its the drivers but need help to locate the drivers
haha, so now i'm thinking. I'm learning the terminal as fast as i can but there are several lines of codes and commands in there that throws up red flags to me that i don't fully understand. It just looks fishy too me. It would be highly appreciated if someone could just check this out just to tell me that i don't need to worry about it. Or point me in the right direction. I just feel un easy about this. ha.
-
Adapter light GREEN but battery does not charge NEED HELP, PLEASE!
My battery won't charge but the problem is a little different from others I have seen posted. The battery shows 3% charge but the adapter light is green. If the computer adapter is disconnected, the computer shuts down (as we would expect at 3% charge). I used another MacBook Pro cord to plug in and the same thing happens.
This is what the System Profiler shows:
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Battery Information:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 2815
Remaining Capacity (mAh): 87
Amperage (mA): 0
Voltage (mV): 9921
Cycle Count: 62
AC Charger Information:
Connected: Yes
Charging: No
I purchased this 15" MacBook Pro (Oct 2006) from a reputable non Apple Apple dealer but f course this problem started a week or so after it was out of their resale warranty. There is nothing to say "check battery" just that it is not charging. It is a trek to ANY apple dealer or reseller and it is hard for me to get there easily so I was hoping someone might have an idea what is wrong and do what I can from home. Could it just be the battery? It seems more like a problem with the adapter connection. OCCASIONALLY, the light on the adapter will flicker on orange/red for a few seconds before going to green.
THANKS!The only way to tell if you have a hardware problem is to trek on down to your local AS or AASP for them to run some diagnostic tests. If it turns out to be just the battery, you can purchase directly from them. I am assuming you do not have AppleCare....
Not sure if you can run the same tests at home. Hopefully, you have the right tools. Search through the following "do-it-yourself" sites:
iFixit
TakeItApart
Also do a YouTube search. Loads of Macbook Pro +"how to"+ videos.
Good luck! -
my mac doesnt recognize my ipod nano G4, its always worked before. read the trouble shoots, checked all connections. it needs to charge and wont do it.
Try the suggestions in article - iPod not recognized in iTunes and Mac desktop. If the suggestions do not work, more than likely you need a new battery. Take the iPod Nano to an Apple store or an AASP. Whichever is more convenient for you.
-
Usb 1.0 won't work - need help urgently
Happy holidays and hope Santa is working overtime
Got iPod nano for my son and mrs. and can't get them to work properly. Long time mac users, G3 iBook at home (mac 10.3.9), g4 iMac at office but neither have usb 2.0 as older machinese.
For some reason, even after downloading 7.5 iTunes, when we connect new nano with usb connector supplied in box, only get that apple icon popping up; can't connect for some reason, can't see nano on desktop.
Tried it with old Sony Vaio, running WinXP but a gain older model, no usb 2 and only usb 1 ports. Can't read there either.
Funny, when I plug with my old 3rd gen iPod charger, using firewire with common plug, it's charging fine.
Can someone explain if it's the usb port that's a problem? Mrs. leaving to visit mother for few weeks early tomorrow morning and I have appointment with genius bar at 10 am - but too late to help her.Yep, on my iBook, got message finally that needed 10.4.8.
Re-tried with WinXp (not sure if SP2) and got it connected, trying to rip some CD to sync and completed about 5 cd. After ejecting nano, couldn't get it to 'turn-on' which is weird - so i'm leaving it connected to pc to charge (instructions say 3 hrs).
My suspicion is this is a lemon.
Btw, can i charge this generation nano with the 'traditional' firewire charger that came with my old iPod (3rd gen)? If we do get it to work, my wife won't have pc to charge with when traveling and I'd like to give her my charger to take along?
Thanks, -
Please help. It started about a week ago, it was charging fine the day before and then I plugged it in and it didn't charge. Occasionally it would begin to charge, but sometimes not. I've tried different cords, USB ports, wall chargers, and computers but it would barely work. Now, it refuses to charge at all. If it dies, and I won't be able to use it anymore, I won't be able to get a new one. Please help me!
It's still under its original factory warranty, so unless you've damaged it in some way, it should be covered.
First, try giving it a reset. Hold down the sleep and home keys, past when you see the red power down slider and until you see the silver apple. Let it reboot and see if that helps.
if not, contact your local apple store and make an appointment and let them check it out. -
Ipad won't charge -- need to back it up
My iPad will not charge and itunes will not detect it. I called Apple and they sent me a replacement cord but still nothing. I am reading on many sites that they will replace it so I need to get my stuff off my ipad. What is going to be the best way since it will not connect to anything?
As stated in the article itself, it won't affect the library. Back it up anyway.
(70163) -
Husband's iphone won't ring. need help please. thanks
My husband's iPhone 4 won't ring. It will vibrate but ringing has stopped. Can't figure out how to change back to ringing. Thanks for any help.
check on the left hand side, above the volume, there is a global mute switch, see if that is off
-
button element won't submit, need help...
This <button> element is used all throughout our site
http://www.ocp.org flawlessly.
However, on the particular page I'm working on right now it won't
work in conjunction with the drop down menu I'm working with in IE
6 or 7, can anyone help me out? Thanks!
I'm working in a private network so I can't show you a live
version of this page but I've attached the code.<button
onclick='window.location.href='/account/orderHistory''
type="submit">
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"Spencer Hill" <[email protected]> wrote in
message
news:[email protected]...
> This <button> element is used all throughout our
site
http://www.ocp.org
> flawlessly. However, on the particular page I'm working
on right now it
> won't
> work in conjunction with the drop down menu I'm working
with in IE 6 or 7,
> can
> anyone help me out? Thanks!
>
> I'm working in a private network so I can't show you a
live version of
> this
> page but I've attached the code.
>
> <form id="userdata" name="userdata" method="post"
> action="/account/orderHistory">
> <table cellpadding="0" cellspacing="0">
> <tr>
> <?php
> if (isset($accounts)) {
> $num_accounts = sizeof($accounts);
> if ($num_accounts >= '2') {
> echo "<select name=cust_id>";
> foreach ($accounts as $cmid => $value) {
> $name = $value['organization'];
> if ($name == '') {
> $name = $value['name'];
> }
> if ($cmid == $cust_id) {
> echo "<option value='" . $cmid . "' selected>" .
$name . ' (#' . $cmid .
> ")</option>";
> } else {
> echo "<option value='" . $cmid . "'>" . $name . '
(#' . $cmid .
> ")</option>";
> }
> }
> echo "</select><button
>
onclick='window.location.href='/account/orderHistory''>submit</button></tr>";
> }
> else {
> foreach ($accounts as $cmid => $value) {
> $name = $value['organization'];
> if ($name == '') {
> $name = $value['name'];
> }
> }
> echo $name;
> echo "</td></tr>";
> echo "<input type=hidden name='cust_id' value='" .
$cmid . "'>";
> }
> }
> ?>
>
> <!--
> <tr>
> <td>Order Start Date:</td>
> <td><input type='text' value='<?php echo
$start_date ?>'
> name='start_date'></td>
> </tr>
> <tr>
> <td>Order End Date:</td>
> <td><input type='text' value='<?php echo
$end_date ?>'
> name='end_date'></td>
> </tr>
> -->
> </table>
>
> <input type=hidden name=action value=history>
>
> </form>
>
> <form id="userdata2" name="userdata2" method="post"
> action="/account/orderHistory">
> <table class="results" cellpadding="0"
cellspacing="0">
> <tr style="text-decoration: none; font-size: 14px;
color: #fff;
> background-image:
url(/ocpimages/tabs/tabs_dscrptn_bg.gif); font-weight:
> bold;">
> <td style="border-right: solid 1px #999;
padding-right: 0;">Date</td>
> <td style="border-left: 1px solid #ccc; border-right:
solid 1px #999;
> padding-right: 0;">Invoice No.</td>
> <td style="border-left: 1px solid #ccc; border-right:
solid 1px #999;
> padding-right: 0;">Status</td>
> <td style="border-left: 1px solid #ccc; border-right:
solid 1px #999;
> padding-right: 0;">Ship Date</td>
> <td style="border-left: 1px solid #ccc; border-right:
solid 1px #999;
> padding-right: 0;">Tracking</td>
> <td style="border-left: 1px solid #ccc; border-right:
solid 1px #999;
> padding-right: 0;">Details</td>
> <td style="border-left: 1px solid #ccc;
padding-right: 0;">Amount</td>
> </tr>
>
> <?php
> if (isset($orders)) {
> $td_class = 'white';
> foreach ($orders as $i => $value) {
> $entry_date = $value['entry_date'];
> $invoiceID = $value['invoiceID'];
> $order_amt = $value['order_amt'];
> $status = $value['status'];
> $ship_date = $value['ship_date'];
> $tracking_id = $value['tracking_id'];
> $tracking_id = explode('|', $tracking_id);
>
> switch ($status) {
> case ('RTP'):
> $status_desc = "Shipped";
> break;
> case ('RTI'):
> $status_desc = "Shipped";
> break;
> case ('O'):
> $status_desc = "Order Submitted";
> break;
> default:
> $status_desc = "Order Picked";
> }
> if ($invoiceID != '') {
> echo "<tr valign='top' class=' . $td_class . '>";
> echo "<td>". $entry_date. "</td>";
> echo "<td style='text-align: center;'>" .
$invoiceID . "</td>";
> echo "<td>" . $status_desc . "</td>";
> echo "<td>" . $ship_date . "</td>";
> if ($tracking_id != '') {
> $suburl = '';
> foreach ($tracking_id as $key => $val) {
> $track_cnt = $key + 1;
> $suburl = $suburl . "&InquiryNumber" . $track_cnt .
"=" . $val;
> }
> $suburl =
> "
http://wwwapps.ups.com/etracking/tracking.cgi?tracknums_displayed="
> $track_cnt .
"&TypeOfInquiryNumber=T&HTMLVersion=4.0" . $suburl .
> "&track=Track";
> echo '<td><a target="_new" href="' . $suburl .
'">Tracking
> Detail</a></td>';
> } else {
> echo "<td> </td>";
> }
>
> $suburl =
"/account/orderHistory?action=detail&invoiceID=" . $invoiceID .
> "&cust_id=" . $cust_id;
> echo '<td><a href="' . $suburl . '">Product
Detail</a></td>';
> echo "<td style='text-align: right;'>$ " .
$order_amt . "</td>";
> echo "</tr>";
>
> $td_class = $td_class == 'white' ? 'blue' : 'white';
> }
> }
> }
> ?>
> </table>
> </form>
>
Maybe you are looking for
-
My existing object styles are not visible
My existing object styles are not visible in the object style panel- only via quick apply (so I know they exist) Any idea how I can make this panel functional again? Using CS6 Thanks!
-
Tracing / Profiling SQL statements in Sybase
Hi Guys, I would like to capture the SQL statements that have been fired from a web app (bit like SQL Server's profiler). Is there such a tool / facility?Please note that I cannot use dbcc commands like traceon as DBA's wont grant me sa rights (in de
-
Comparison of schemas across different database Instances
Hi All, I need to compare around 8 schemas across 4 different instances. We expect them to be same (atleast constraints and indxes) but we have some exceptions. Don't have any database link. I tried using PL/SQL developer , it gives only changes for
-
Jusat the other day i started getting prompted for Security Information required when trying to download apps. on my Ipodtouvh 4Gen. Typically when I download an app. I get asked for my apple ID and then it will allow the download. This new prompt
-
Can I create a Formula with Multiple Products [ Not Co Products ] ?
hi There, Have a simple question & Doubt. Is it okay to create a Formula with Multiple Products in OPM ? If Yes, how does the Formula behave with respect to Standard Costing Subledger. If not, what are the reasons for not creating formula with Multip