My safari doesn't work sometimes, but I connect with the internet.

my safari doesn't work sometimes, but I connect with the internet. Some of the videos I can't see with the Safari browser, but I can see it with other brower. But my friend can see these videos with her safari. And I can not connect with the app store sometimes.

Before you try to configure the settings on your Router, first thing which you need to do is, Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable...
Connect the Modem to the Linksys Router on the Internet Port and then connect your computer to the Linksys router on the LAN Port 1. On your Computer click on Start - Run - CMD and click Ok... Now in the Command Prompt window type "ipconfig" and hit enter and note down the "IP address, Subnet Mask and Default Gateway" , Now again in the Command Prompt window type "ping default gateway IP" and hit enter and check if you are getting any replies, If yes then you can login to the setup page of the configure all the settings on it from scratch. 
If your Internet Service Provider is Cable follow this link

Similar Messages

  • My WRT350N doesn't work anymore, just stopped connecting to the internet

    I WRT350N was working for a while, I came home from a trip and it was up, I connected to it, but no internet. I went through a series of checks with the cable modem which was working. I swapped out the router and connect back to the internet. I've tried all the procedure for resetting and resetup and no internet.  I found that I was down level on the firmware to I download the latest and follow the instruction to load it. Got to 98% and it failed. Now I can not even access the router. It comes on, I see the light, but now I can't even get an IP from the device.  Any clue?  I can't find my receipt on when I brought the device, I know it was middle of 2009. and the website doesn't provide good information on how to get service.
    (Mod note: Edited post for guideline compliance. Thanks!)
    Message Edited by JOHNDOE_06 on 01-14-2010 08:44 AM

    Before you try to configure the settings on your Router, first thing which you need to do is, Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable...
    Connect the Modem to the Linksys Router on the Internet Port and then connect your computer to the Linksys router on the LAN Port 1. On your Computer click on Start - Run - CMD and click Ok... Now in the Command Prompt window type "ipconfig" and hit enter and note down the "IP address, Subnet Mask and Default Gateway" , Now again in the Command Prompt window type "ping default gateway IP" and hit enter and check if you are getting any replies, If yes then you can login to the setup page of the configure all the settings on it from scratch. 
    If your Internet Service Provider is Cable follow this link

  • We live in motel but my iMac is not connecting with the internet but my cousin has hp laptop that works perfectly fine in my room. So can you help me with this situation?

    We live in motel but my iMac is not connecting with the internet but my cousin has hp laptop that works perfectly fine in my room. So can you help me with this situation?

    Joining an encrypted WEP or WPA Wi-Fi network

  • I am trying to connect to my friend's wifi, i have a very strong signal indicated on my ipad, but cannot connect to the internet.  Yesterday i connected without any problem, can anybody tell me why i cannot connect today?

    i am trying to connect to my friend's wifi, i have a very strong signal indicated on my ipad, but cannot connect to the internet.  Yesterday i connected without any problem, can anybody tell me why i cannot connect today?

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • How to restart base station from airport utility? I used to be able to do it remotely  I currently use a Mac Pro 10.8.4 and have a time machine for wireless 6.3 (630.34). Sometimes I cannot connect to the internet and use network preferences to diagnose t

    How to restart base station from airport utility? I used to be able to do it remotely
    I currently use a Mac Pro 10.8.4 and have a time machine for wireless 6.3 (630.34). Sometimes I cannot connect to the internet and use network preferences to diagnose the issue. This results in being told to restart the wireless. The airport utility includes the drop down option of restarting but is not clickable so I can't choose it.
    With my prior macbook and same time capsule, etc  if i had problems connecting to the internet I would run network diagnostics to help out. This included clicking on the airport utility ---> base station --> restart. This worked most of the time.
    Bottom line, is there something I am missing in not being able to restart the wi-fi remotely? ]
    Thanks in advance

    You are likely forgetting a step.
    Open AirPort Utility
    Click on the Time Capsule icon
    Click Edit in the small window that appears
    Now click the Base Station menu.....top of the screen....not the Base Station "tab" in the center of the screen
    Click Restart

  • I have a Power PC G4 which is running on OSX 10.5.8, it has the AirPort utility but cannot connect to the internet as my iMac can, I think I might need an AirPort Card? Is that the case or do I need something different to connect to a wireless modem?

    I have a Power PC G4 which is running on OSX 10.5.8, it has the AirPort utility but cannot connect to the internet as my iMac can, I think I might need an AirPort Card? Is that the case or do I need something different to connect to a wireless modem?

    Welcome!
    Only one variant of the PowerMac G4 could use the faster Airport Extreme Card. The rest used the original Airport card that is pretty slow.
    To get fast wireless without buying more than one thing, consider this:
    http://eshop.macsales.com/item/Edimax/EW7722IN/
    It goes in an available PCI slot
    There are USB solutions also. However, all PowerMac G4 towers had only slower USB 1.1 ports, so any USB wireless adaptor can only run at about wireless 'B" speeds (slow) unless you also install a PCI USB 2.0 adaptor card. Doing that would allow a USB wireless adaptor to run at its maximum rated speed. These items working together would accomplish that:
    USB wireless "dongle:"
    Newer Technology MAXPower 802.11n/g/b USB Adapter + Plug and play direct or with extension cradle
    USB PCI adaptor:
    http://eshop.macsales.com/Search/Search.cfm?Ntk=Primary&Ns=P_Popularity%7c1&Ne=5 000&N=7069&Ntt=USB+PCI
    Each approach has its advantages. The PCI wireless card is a one-piece solution that takes up no desk space. The USB2 card+USB2 Dongle gives you more fast ports for transferring date from other external USB devices (primarily cameras and external hard drives) at hugely faster rates than can the original ports. I have a USB 2 PCI card in my G4 tower strictly for transferring images from my digital SLR camera in a timely manner.

  • Your Apple TV is connected to your wi fi network but cannot connect to the internet.  Airplay logo not available on ipad3, iPod touch3g and showing intermittently in iTunes on windows laptop.  Switched ISP a few days ago.  Entered pass key info on all.

    I switched ISP a few days ago and had problems with airplay since.  After restarting and reinstalling and updating, re entering pass keys for new wi fi on everything,  Apple TV shows:  Your Apple TV is connected to your wi fi network but cannot connect to the Internet.  Ipad3 and iPod touch 3G have no airplay icon or get one briefly then it disappears again.  Same with itunes on windows laptop.
    Can anyone help?
    Bob

    Welcome to the Apple Community.
    Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
    You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
    Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
    There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment.

  • Apple TV connects to the network but cannot connect to the internet.

    Apple TV connects to the network but cannot connect to the internet. Works on other Apple TV's we have just not this new one. Defective???  Thank you!

    This might help:
    Apple TV (2nd gen.) saw my wireless network but did not accept my password (gave a network error message). It fixed instantly doing this:
    Made a note of the Apple TV's MAC address. Get it by pressing Menu on the remote, then Settings > General > About. It's called "WiFi address."
    Use your browser on a network connected computer to go to your router settings (usually 192.168.1.1).
    Under "Wireless > Wireless MAC Filter" (or something similar) do these steps:
    Enable Wireless MAC filter
    Enable "Permit PCs listed below to access the wireless network"
    Enter the Apple TV's MAC address
    Click "Save Setting"
    When I did this the network connection immediately started working.
    Note: These instructions are based on a Cisco Wireless-N Broadband, model WRT160Nv2, firmware v2.0.02.

  • Firefox 3.5.1 on WinXP automatically switches to "Work Offline" when a connection to the internet drops. User must un-click "Work Offline" for it to work once a connection has been restored. Why?

    Firefox 3.5.1 on WinXP automatically switches to "Work Offline" when a connection to the internet drops. This was not the case with earlier versions. Why is this necessary? Is there an option/preference setting to change this?

    # Yes, if you go to accounts.firefox.org, sign out, you will now be signed out.
    # Sign back in, and you will be asked to save the password you entered.
    # This will save the password and autocomplete if you have this option turned on.
    I am not exactly sure why the menu did not detect the password change or if it was stored incorrectly after you changed it? But after storing the correct password you can manage any duplicate passwords in the password manager.[[Password manager - Remember, delete and change saved passwords in Firefox]]

  • HT5205 I am roaming but cannot connect to the internet?

    I am roaming with my iPad, but cannot connect to the internet?

    I am roaming with my iPad, but cannot connect to the internet?

  • I recently moved into a new apartment and I can connect with the internet by direct connection to the cable/internet modem.  But when I connect my Airport Express, it just blinks with a yellow light and I cannot connect via WiFi.  Any suggestions?

    I recently moved into a new apartment and can connect with the internet by direct attachment to the cable/internet modem.  But when I try to connect the modem to my Airport Express, the Airport just blinks yellow and I cannot get my WiFi.  Any suggestions?

    Try this User Tip from forum expert Tesserax:
                     AirPort - Complete Power Recycle

  • I cannot connect to the internet using apps but im connected to the internet!

    i cannot connect to the internet using apps but im connected to the internet!

    What makes you think that you are connected to the internet then?
    Try:
    - Resetting the iPod. Nothing will be lost.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    - Reset ntwork settings: Settings>General>Reset>Reset Ntwork Settings.
    - iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections

  • The touch screen doesn't work when I'm surfing on the internet.

    The touch screen works correctly but not when I'm surfing on the internet. I can't scroll or do anything else with the screen then. There 's no problem with the internet connection because I can see I've some new e-mails but I 'can't open them because of the screen. can you help me?

    Try resetting yur iPod:
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    However, for many webpages when you want to scroll in a window you need to use two fingers, not one finger.  Also, it appears that you are using webmail, sometimes because of the way the website was designed, it is not fully compatible with iDevices.  Sometimes using a different browser (not Safari) helps but sometimes you just can't fully use webmail.  Wht provider are you using?

  • I just upgraded my operating system and can't get the imessage to work.  I get a message it check my network connection.  But I am able to connect with the internet

    I just upgraded to the new operating system on my iphone 4.  I am trying to connect to imessage but I can't get it to work.  I get a message saying to check my network settings.  I have checked and I can connect to the internet.  Any idea what I need to do?

    If you have updated to iOS 5 then when you want to use messages you need  register by going into settings then go to messages and  then turn it on and use your apple I tunes ID. You can only use it between other  updated devices.

  • Wifi is working but cannot connect to the internet

    I am using windows 8.1
    My wifi is working - my iphone and ipad can use it and my PC is connected to my broadband but I cannot connect to the internet. I have turned everything off and on a number of times.
    I am totally stuck as to how to fix this.

    Presumably you are connecting by Ethernet. Has this just started to happen or have you never been able to connect?
    Have you tried changing the cable, is it plugged in correctly, have you tried plugging it into different ports on the homehub?
    Have you checked that the computers firewall is not set to block connections, see link
    http://windows.microsoft.com/en-gb/windows-8/windows-firewall-from-start-to-finish
    If you are not using the Windows fiewall have you checked to see if your antivirus/firewall is blocking connection?

Maybe you are looking for

  • Disk Repair For A DYI Fusion

    About 4 months ago I purchased a solid state drive and installed it with a regular drive (installed where the optical drive was originally located) in a Macbook Pro OS 10.8.4, 2.8 ghz i7 Core.  I followed directions provided by Other World Computing

  • Logical components for ERP and ERP EnhP 3

    Hello, We have a landscape or ECC 6.0 Systems created in the SMSY.  Those systems were linked to a new logical component Z_ERP60 under product ERP 6.0.  Then  we used that logical component in all the projects. Later on, we upgrade ECC 6.0 to EnhP 3.

  • HP 6300 all in one can't set up for wireless use

    can't set up for wireless use

  • Photo library way too big

    ive delet almost all the photos from my iPad, and yet the photo library is still 4.1GB?  How so?  The deleted photos album is empty - so are my photos being stored somewhere secretly?

  • Is it me or is it Dreamweaver?

    I am attempting to build a website using Dreamweaver 8 and everytime I insert an image into a blank page, table, or existing template, there is a broken image icon that appears. I've tried organizing into folders, defining a site, and even adding ima