My Satellite notebook shows "Spin retry count" warning

Hi first time user hope I get this write, I am using system mechanic pro latest version and on the hard drive monitor status it is showing a warning for the spin retry count.
My laptop is only 2 months old should I be worried? and have it looked at. Thanks in advance. Operating system is win8.1

In my opinion there is no reason for panic. You are using third part software and they have own rule for reporting S.M.R.T values.
If there is no other problem I think everything is OK.
Open preinstalled PC health monitor and check HDD Status. What is reported there?
I hope Good.

Similar Messages

  • Spin Retry count again (plz help)

    Hi,
         My 11 month old macbook pro (2011) was recently sent under warrenty for Harddisk SPIN RETRY COUNT value increase. They changed the harddisk and installed new Toshiba harddisk. Which ran 100% S.M.A.R.T health for two weeks and now it is showing same Spin retry count problem. I am thinking its not the harddisk but something else is causing the problem( may be power supply problem). I am from nepal so it takes a lot of effort to send it in for repair. Any help on this topic will really appreciated plz. Scaned it with disk radar and Techtool.

    AFAIK, this SMART parameter indicates a mechanical problem. Which would mean that you've experienced two different hard disks with mechanical failure in a row in the same machine. While not impossible, I should expect this to be rather improbable.
    A power supply issue may be the cause, but then I'd expect other symptoms as well. Here's what I'm thinking:
    (1) SATA cable. Problems with SATA cables are common in laptops.
    (2) Alternatively, a long shot: ambient air pressure. You mentioned Nepal. If you're in the Kathmandu Valley, it's not an issue; but if you take your MBP above, say, roughly 3200m, it may become a problem for the hard disk.

  • SMART tests PASS, but my Spin-up Retry Count is in the yellow

    I've had my computer for almost three years. AppleCare is on the verge of expiring. I just toook my MacBook in for a trackpad replacement.
    I use TechTools Pro for my hardware testing. My computer passes all of its tests, but I notice that the test for the Spin-Up Retry Count on the SMART status of my harddrive is not totally in the red, but in the yellow, and even then its closer to green than to red. My computer still works great. It does slow down and Spinning-wheel-of-death alot when I'm doing alot of high-CPU load tasks, but for the most part, it still works great. Is this Spin-Up Retry Count something I should be concerned with? My other tests report no bad sectors, bad blocks, or anything else wrong.

    Back up all data, then uninstall the worthless, time-wasting "TechTool" product according to the developer's instructions. Reboot. Problem solved.
    Oh, that made my day. I actually did that, when I found the Unix tool smartmontools. Set it to perform a full check weekly, and email me if SMART check failed. No use seeing that stuff Techtools shows you.

  • Validation error on retry count for session bean

    Hi,
    In our weblogic-ejb-jar.xml we have configured a retry count for a specific method on a local session bean. When I click on 'Browse' to select a specific method, it only shows '*' as a possible value. When we type the method name by hand, it shows a red cross next to the input field with the error 'Cannot find method "exampleMethod()" in the ExampleBean's Local interfaces'.
    We use EJB 3.0 and OEPE 12.1.1.0.1 with Eclipse 3.7.2
    The weblogic-ejb-jar.xml looks like this:
    <?xml version="1.0" encoding="UTF-8"?>
    <weblogic-ejb-jar xmlns="http://xmlns.oracle.com/weblogic/weblogic-ejb-jar"
            xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
            xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/ejb-jar_3_0.xsd http://xmlns.oracle.com/weblogic/weblogic-ejb-jar http://xmlns.oracle.com/weblogic/weblogic-ejb-jar/1.2/weblogic-ejb-jar.xsd">
        <retry-methods-on-rollback>
         <retry-count>3</retry-count>          
            <method>
                <ejb-name>ExampleBean</ejb-name>
                <method-intf>Local</method-intf>
                <method-name>exampleMethod</method-name>
           </method>
        </retry-methods-on-rollback>
    </weblogic-ejb-jar>The bean looks like this:
    @Stateless(mappedName = MappedName.DONNA)
    @TransactionAttribute(value = TransactionAttributeType.REQUIRES_NEW)
    public class ExampleBean implements Example {
    }And the interface:
    @Local
    public interface Example {
    }Does anyone else have this problem?
    Thanks.
    Pieter

    Hi Pieter,
    This is a known issue and I will keep you posted on the development.
    Thanks for your feedback!
    -Ram

  • Message retry count for the message has been exhausted

    Hi,
    I am using 'Custom Document Over Internet' with HTTPS as transport protocol. I have set the acknowledgement mode to Sync in order to receive the synchronous response. B2B is able to post the HTTP request successfully and in turn it receives a synchronous response and a MDN message. At the initial stage, after posting the request it shows the state as 'WaitForAck' for request message and for response and MDN messages, the state is completed.
    After some time when we check the state of request it is changed to 'Error' with the error message as 'Message retry count for the message has been exhausted'. We have not set the retry count and retry interval and so after retrying for 3 times with an interval of 120 minutes it is showing error state as it is not able to correlate the incoming response to the corresspoding request. We have tried the option of setting the Message id of the request in 'replyToMsgID' parameter of response header and tested the flow. But still I am facing te same issue. Please help me to resolve this issue.

    Hi Anuj,
    The property mentioned by NandaGopal has already been added in tip.properties file. I sent the B2B logs in debug mode and tip.properties file to your mail id. Please have a look into that. The result of opatch lsinventory command is
    Result:
    Installed Patch List:
    =====================
    1) Patch 9234704 applied on Fri Jan 15 16:41:12 GMT 2010
    [ Bug fixes: 8870866 9143036  ]
    [ This patch overlays patches " 8703410 " ]
    [ This patch needs patches " 8703410 "  as prerequisites ]
    2) Patch 8703410 applied on Thu Jan 07 17:56:08 GMT 2010
    Unique Patch ID: 11901808
    [ Bug fixes: 7652646 7497854 7664370 8708445 7661101 7007789 6352814 6802446 7665607 7641078 6496457 6013963 8330151 7305413 8619657 7460584 7529893 7458954 7020996 8393885 8210401 6329207 6740403 7126458 6511970 8783577 7379065 7230993 8704965 6774631 7198642 8309511 8392729 7661769 7605518 7479148 6733262 8349002 6736026 7322333 7242500 7239355 8746561 8344645 8451004 7645440 6747966 6369424 6737334 8339176 6774134 7046561 6412124 7210461 7506319 8630406 8235175 7258882 7184318 6453359 7456866 7673646 6043277 7457597 6769895 7193710 8239170 7668247 8404955 8612841 7261965 7132740 7485790 6518386 7305363 6852370 6433256 7673431 6764239 8360048 7501748 7379153 8281019 7498031 8216457 7046574 6875312 6754906 6656289 6417367 7658271 7556011 7000190 6979467 8594506 8691820 6852308 8475848 8518443 7600385 7211208 6732051 8524862 7461051 8263026 7609467 7379161 7672714 6353293 7157229 7594997 7211287 7034069 7563311 6822375 6640935 7359202 6769261 6919593 8601869 6029507 6974391 7139013 7518641 8605719 6817264 7501903 7496014 7576785 8666761 7130151 7322581 5523563 7680097 8508905 7241737 7660780 8480395 7660781 7191994 6924921 7672723 8432093 6800745 8703404 8540335 8507242 8608121 8217566 7481317 6639030 6200414 7529795 7354853 8475867 7376270 7303860 7016005 7678901 7368610 8992520 6881977 6016128 7033061 6397084 7672730 8703410 7709562 6449656 7045589 8508054 6491068 7378745 7643811 7435853 7615836 8707416 6447557 7379042 6940476 7670634 6950383 6764273 6962327 7478322 8546454 7157324 8871403 8862082 7184219 7672744 7164618 7672745 7230184 7576730 7590301 8746541 7261863 8327427 6769430 8295683 7526186 8298731 6414280 6139955 6646997 7692853 8233048 6794296 7457066 8552373 8225241 7706387 7204022  ]
    3) Patch 4601861 applied on Fri Nov 14 04:24:08 GMT 2008
    [ Bug fixes: 4601861  ]

  • Can a bad download cause my spin retry cycle to suddenly fail?

    Hey everyone,
    So I recently left for a few days on vacation and my younger sibling was using my macbook pro while I was gone. Well, they were downloading something and all of the sudden application stopped and internet cut out. The Internet wouldnt come back for 6 hours (thats how long it took them to fix it!). He was afraid and stopped using my computer (im guessing he was using utorrent or something equally stupid). Well, when i came back and started to use my macbook, it would not stop screen freezing. I get the beach ball of death CONSTANTLY, and its become a terrible hindrance to my university work.
    So after trying everything, I downloaded techtool pro 7. I have used the Smart function, and was astonished to see that everything was perfect except one category. Spin retry cycle is very high, to the point where its almost failing. After smacking my sibling around in anger (kidding), i now come to everyone here for some solutions! I have read that spin retry cycle is a imminent indication to hard drive failure, but I really cant see how this is possible. My macbook was PERFECT before I left. All my sibling did was do the download, have the download suddenly freeze, have the internet cut out for some reason, and then in fear shut down my computer. The freezing started immediately after this "frozen download". Could this spin cycle warning be from something other than hard drive failure? Like I said, this was an overnight thing. Perfect to freezing. Could the download have corrupted a file or fragmented a file to cause this? Is there any possible way other than replacing the whole hard drive to fix this? Will defraging help?
    Thank you so much for your time!!

    If the Safari reset or Font check doesn't help, the issue is either at the software (OS X) or hardware (hard drive) level. In the IT world it all comes down to how much time you want to spend dealing with/fixing the problem.
    This is a shot in the dark, but create a new user account, see how the performance is.
    The last thing in my bag of tricks is to re-install the MacOS.
    Run a Time Machine backup to an external hard drive first.
    Be sure that you have all of your licence keys and installers for any paid software.
    Then boot up in recovery and connect to the internet
    Erase the disk
    Run the MacOS installer.
    Otherwise, if performance is not better with a fresh Lion installation, get a new disk

  • Inbox and Drafts show unread message count of all folders within. Can I get the local folders to do this too?

    I'm filtering mail into folders in the local folder tree. There may be two or three levels, e.g., Local Folders -> Lists -> OS -> MacOSX. Mail that is unread in the MacOSX folder is counted and displayed when the MacOSX folder is visible. However, keeping the entire tree on display is a nuisance and it is long, so I don't see things ate the bottom. I have to scroll to reveal the rest of the items in the folder tree. For these reasons I'd prefer to have the folder tree in its minimal state.
    Is it possible to have the the top level folders display an unread message count for all the enclosed folders?

    when I collapse the folder tree of local folders, it shows the unread count for sub folders.

  • Instead of Retry Count is to 0,file is coming twise in OSB.

    In my OSB project ,the xml file is polling from a folder ,after that it is transformed through Xquery,then it goes to a DB. I have added a route level error handeller ,if any error occurs a file will be generated with this payload and stored in a folder. Everything is working fine.but if any error occurs then all time 2 file is generated.though  retry.count=0 in adapter and business service also,where did i make mistake,please advise..

    Please provide some valuable answer. I am not able to understand why this is happening????
    Thanks!!

  • Will not boot up. Apple shows, spinning wheel shows, a bar comes up on the bottom. It gets to the end of the bar and shuts down.

    Will not boot up. Apple shows, spinning wheel shows, a bar comes up on the bottom. It gets to the end of the bar and shuts down.

    Will not boot up. Apple shows, spinning wheel shows, a bar comes up on the bottom. It gets to the end of the bar and shuts down.

  • I need to play back a video-recording i have taken myself and have it show the time count in seconds on the play back. Can you help?

    I need to play back a video-recording that I have taken myself and have it show the time counter in secs/minutes in the playback. Can anyone help?

    the movie editing app "Avid Studio" displays a time counter, as does the Pinnacle editing app.  Oddly enough, I movie does not.  (unless I have it somehow turned off.)

  • Fault policy and jca.retry.count in 11g

    I have a composite which has the architecture as follows :
    Adapter (File) -- Mediator -- Adapter (FTP)
    The mediator follows sequential routing pattern
    I have configured jta.retry.count = 3 for the FTP adapter.
    Also the composite refers to the fault policy file from the MDS
    In the fault policy file the ora retry action is defined as follows :
    < Action id="ora-retry">
    <retry>
    <retryCount>1</retryCount>
    <retryInterval>5</retryInterval>
    <retryFailureAction ref="ora-rethrow-fault"/>
    </retry>
    </Action>
    We have configured the following rejection handler for the file adapter :
    <faultName xmlns:rjm="http://schemas.oracle.com/sca/rejectedmessages"
    name="rjm:FILE_RD_B2BOutFolder_Files">
    <condition>
    <action ref="ora-ws"/>
    </condition>
    </faultName>
    We get the following message as part of rejection message email notification :
    The adapter has exceeded maximum configured retries. The adapter has exceeded maximum configured retries. The adapter was unable to process "{0}" after having retried for {1} times, now the adapter will reject the message. This exception usually comes due to errors in downstream systems. Please increase the value for "jca.retry.maxRetries" in composite.xml for the inbound service and redeploy.
    I have the following doubts:
    1. When the FTP adapter fails because of a remote fault, which retry will be executed fault policy or jta.retry.count ?
    2. If the jta.retry.count is executed then can I see 3 instances on the EM console or any other entry in the Log file.
    3. where can i configure jca.retry.maxretries property. this property is not available on emconsole.

    Hi,
    Section 12.4.4 and 12.4.5 should answer your questions.
    http://docs.oracle.com/cd/E12839_01/integration.1111/e10224/bp_faults.htm#BABICJAD
    Regards,
    Neeraj Sehgal

  • DB adapter retry count value

    Hi gurus,
    I am using a db adapter for polling options. The option used is 'Delete the row(s) that were read' .
    Here the retry count by default is set to unlimited. Is this the recommended one? In normal db adapter options i see the retry count as '4'
    the property value seen in composite.xml is shown below
    <property name="jca.retry.count" type="xs:int" many="false" override="may">2147483647</property>
    Will this lead to any performance issues? Or what could be the correct retry count value?
    Please let us know.

    Hi,
    We have used the polling options using Logical delete vastly in our project and never faced any performance issues with respect to this property value being set to 'unlimited'.
    I believe there should not be any performance issues with respect to the 'Delete the row(s) that were read' option as well.
    According Oracle documentation:
    In the Auto-Retries section, specify the value for auto-retry incase of time out. In case of a connection related fault, the Invoke activity can be automatically retried a limited number of times. You can specify the following values in the fields in this section:
    To retry indefinitely, type unlimited in the Attempts field.
    Interval is the delay between retries.
    Backoff Factor: x allows you to wait for increasing periods of time between retries. 9 attempts with a starting interval of 1 and a back off of 2 leads to retries after 1, 2, 4, 8, 16, 32, 64, 128, and 256 (28) seconds.
    Thanks,
    Deepak.

  • Retry counts on multi consumer queues in Java

    Is there a way to get the retry count of a message that has been dequeued from a multiconsumer queue? I believe we were able to access the retry count of a message on a single consumer queue, but when dequeuing from a multiconsumer queue, the retry count field is not filled with a value.
    Can this be done?

    Is there a way to get the retry count of a message that has been dequeued from a multiconsumer queue? I believe we were able to access the retry count of a message on a single consumer queue, but when dequeuing from a multiconsumer queue, the retry count field is not filled with a value.
    Can this be done?

  • Retry count and retry Interval fields in Business service (Http protocol)

    Is retry count and retry Interval in OSB business services(Http protocol) defined for retrying the application errors or for communication errors?
    Also even if my connection timeout is 0 I get an error response due to communcation issue in abt 2.5 mins.
    Please explain.

    - There is an explicit configuration on business service called "Retry Application Errors", if enabled application errors will also be retried.
    - If timeout is not set on business service then domain level timeout configuration comes into effect which is by default of 180 sec i.e 3 mins.
    Hope this helps.

  • HELP ! Making a retry counter

    I'm making a retry counter for the logins and I'm using the j_security_check from Tomcat.
    I made a little class that must check if there is a session object.
    if not create one and put the value 1 in it, for the first try.
    If there is a session object, increase the value and put it in the session object.
    Now is my problem that I get a nullpointer exception and I don't know how to fix it.
    This is the code:
    package beans;
    import java.io.Serializable;
    import javax.servlet.http.*;
    import  javax.servlet.jsp.PageContext;
    * @author Sander Stad
    public class LoginCountBean implements Serializable{
         private int count;
         private String loginTries = null;
         private Integer logins;
         HttpSession session;
         HttpServletRequest request;
         PageContext pageContext;
         public LoginCountBean(){
              count = 1;
         public boolean checkSessieObject(){
              boolean retry = true;
              loginTries = (String) pageContext.findAttribute("logins");
              if(loginTries == null){
                   count = 1;
                   logins = new Integer(count);
                   setSessieObject(logins);
              } else{
                   count = Integer.parseInt((String) pageContext.findAttribute("logins"));
                   if(count >= 3){
                        retry = false;
                   } else{
                        count++;
                        logins = new Integer(count);
                        pageContext.setAttribute("logins", logins, PageContext.SESSION_SCOPE);
              return retry;
         public void setSessieObject(Integer logins){
              request.getSession();
              pageContext.setAttribute("logins", logins, PageContext.SESSION_SCOPE);
    }

    How does the bean get the request and pageContext objects?

Maybe you are looking for