My signal is strong yet I can't access to the Internet.
I tried all procedure to access my Ipad to the Internet,yetit says I'm not connected. Can somebody tell me how?
Go to Settings > Wi-Fi > Network Settings (right arrow of etwork you want to connect to) and see if you are being assigned an IP address.
Similar Messages
-
IPhone 4s with ios 6 shows full wifi signal but can't access to the internet while other idevice can
Hi everyone,
I updated my iphone 4s to ios 6 a few months ago and there was no problem until I change my sim card to other carriers last two days. This second sim card is the same sim card that I used it earlier this year with no problem. But the problem I face is when my iphone goes to sleep mode I realised that I can't receive any push notification from imessage, Whatsapp, and Line. When the phone is awake the wifi signal is back and I have to go to each application in order to get the message. I have tried the following methods but it didn't work: reset all network settings, restore as new iphone, push home and power button together, switch off my iphone, turn on airplane mode, and even change my router. At the moment I have restored my iphone as new for the 5th times.
Now the problem is worsen, after the phone is sleep for about 5 minutes and when I awake my iphone it shows the wifi signal. But I can't access to the internet at all. It shows no working internet on Whatsapp. Safari can't load any web page, the weather app can't update temperature etc. I have to switch off and switch on wifi in setting menu so that I can use the internet. And when I leave my iphone four about 5 - 10 minuetes then the problem start again. While I can't access to the internet on my iphone 4s, I used my dad's iphone 4s with ios 5.0.1 and it works just fine with the internet. My laptop can also access to the internet with the same wifi network but not my iphone.
Does anybody know what's going on with my iphone 4s? Is it the bug from IOS 6 or my iphone is broken? Please help me.
Thank you.Any update will cause problems for a few users. And those users will rush here and post "the sky is falling" stories about their experience. The 99.99% of people who have no problems after an update won't bother to post here; indeed, most of them don't even know ASC exists. FWIW, I had no problems with iOS 7 on my 4S. Your problem is most likely not related to iOS 6, but you should probably update anyway. For addressing the battery issue see this outstanding article: http://www.overthought.org/blog/2014/the-ultimate-guide-to-solving-ios-battery-d rain
-
My WiFi signal is good but I can't connect to the Internet and it's still loading the server
My WiFi signal is good but I can't connect to the Internet and it's still loading the server. How can I fix this or make the server connect faster?
try:
iOS: Troubleshooting Wi-Fi networks and connections -
Good Morning,
We are getting this error
Outlook Web Access is currently unavailable. If the problem continues, contact technical support for your organization and tell them the following: No Client Access servers
of the appropriate version can be accessed from the Internet
We installed a new Exchange 2007 CAS on Windows 2008R2. Got rid of old CAS on Exchange 2007. Now seeing this error. Does anyone have an idea??Hi,
If the issue persists, I recommend you install Exchange 2007 SP3 RU7 and check the result. Also, ensure that Exchange 2010 SP2 RU1 or later version is installed. Old Exchange version may lead to the CAS-to-CAS proxy incompatibility.
What's more, here are some helpful blogs for your reference.
Exchange 2010 SP2 RU1 and CAS-to-CAS Proxy Incompatibility
http://blogs.technet.com/b/exchange/archive/2012/02/17/exchange-2010-sp2-ru1-and-cas-to-cas-proxy-incompatibility.aspx
OWA Coexistence With Legacy Versions
http://blogs.technet.com/b/sjimmie/archive/2010/07/09/owa-coexistence-with-legacy-versions.aspx
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support -
How can I access to the internet by my mobile ?
I can not access to the internet by my mobile (N95) with wireless
I mean the web icon doesn't open..
Is there any one help me... please.Most smart TVs come equipped with wired network access and an option for wireless as well. Connecting the TV to a Wi-Fi network is similar to connecting any wireless computer. That is, you would need to enter the network name (or SSID), security type, and security password.
In addition, the TV should default to a DHCP client. Meaning that it would try to contact the DHCP server in your router to get its IP address information. That would include an IP address and Gateway IP address. By default, your AirPort Extreme will assign local network clients, including your TV, IP addresses in the 10.0.1.2-200 range. Its Gateway IP is: 10.0.1.1 -
Why is my wi-fi signal is going strong, but I can't connect to the internet?
Before I begin, here's my set-up:
My wi-fi signal (on the top right side of my MacBook) is going strong (with all the bars). And a green light is lit up on my Airport Extreme. For some reason, I still can't connect to the internet/use Apple Mail/use iChat. I don't think that there's anything wrong with my MacBook, as my wife isn't able to connect to the internet with her iPad or with her laptop either.
I'm thinking that I have the strong wi-fi signal showing up on my computer because it actually is connecting to the Airport Extreme, yet the airport extreme somehow isn't connected to or isn't able to connect to the router. Would this be correct? Any ideas of how I might fix this? I tried unplugging and replugging everything for a few seconds. However, whenever I use a hardwire ethernet connection to my MacBook, my internet and everything works.
ALSO, of note, I just purchased an Apple Time Capsule. I just realized that it functions as a wi-fi base. Any chance that my computer, my wife's iPad and laptop are just connecting to the Time Capsule instead of the Airport Extreme?
Any answers would be more than appreciated. Thanks!Deselect Proxies if selected.
Safari > Preferences > Advanced > Proxies:
Click "Change Settings" button
The network preferences window for Proxies will will show up with "Proxies"
tab selected.
Under "Select Protocol", uncheck any box if selected.
Click "OK", then "Apply" -
my ipod worked fine yesterday i could go online. I could facebook and use safari. Today I cannot. It says it is connected. I have tried everything from resarting my router to restoring my ipod. I have rentered the password. i have tried other networks same problem. Does anyone know of anything else to do?
wait a couple of days and see what happens, the ipod might just be in turmoil from something. Just a wait awhile and try every couple of hours, thats all i can do or know of to do. I hope your ipod can connect to the internet again soon. if your ipod is a gen four, it might be the new update.
-
i am trying to connect to my friend's wifi, i have a very strong signal indicated on my ipad, but cannot connect to the internet. Yesterday i connected without any problem, can anybody tell me why i cannot connect today?
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
The wireless symbol is present and indicates a strong signal, but I can not connect to the Internet.
The wireless symbol is present and indicates a strong signal, but I can not connect to the Internet. I'm on my home network and have never had trouble before. My iPad is current on all updates. I have tried to reset the network settings, nothing has worked. I can connect to the internet via my iPhone personal hotspot and all other wireless devices are operating normally on my home wireless network.
I am also having this issue. My boy just got an iPod 4 touch, upgraded to iOS 6. I have a D-Link DGL-4300 108G Wireless Gaming Router. With the iPod I can connect to the router, get an IP address (either DHCP or Static) and even browse through the menu on the router, but I can't connect to the internet.
With a DHCP IP address the iPod give the error "Not connected to the internet" with the static IP address it takes a long time when trying to connect to a website but then it gives the error "server stopped responding".
Clearly the issue is in some setting in the router. I've tried setting up a filter so that the iPod will always have access based on MAC address. I've tried changing the various wireless connection settings, all to no avail. I would greatly appreciate some guidence here. -
Can't connect to the internet in my home yet other devices can. I tried it in other wifi places and it connects without a problem. My home wifi is with ATT Uverse. I cheched the IP address on my laptop and its different than on my Ipod although it on the same network.
Move off WEP to WPA or, preferably, to WPA2 (as recommended by Apple). WEP has been deprecated by the WiFi Alliance since 2004 as insecure (it can be cracked in seconds by any hacker).
Note that each device on a network has a unique IP address but if your address starts with 169 then you did not get a valid IP address assigned to you by your router. If restarting the router did not cure the problem then you should check for a firmware update for your router. -
I have my home wifi working ok, full signal, wifi switched on, on my iPad, but I can not go on the Internet, message, FaceTime, etc. Any thoughts please ???
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I can't seem to enlarge the text on my news apps SI and The New Yorker. Yet, I can touch and expand the test on my mail and websites. How come?
I heard someone once talking about the NY app - it's the best selling one in the publisher's line (Conde Nast?), and they deliberately kept it as simple and "untechy" as possible - the closest in their line to the actual print edition. The discussion was on how it was surprising that the magazine with the least amount of "bells and whistles" was their best seller... and a speculation that it was because it was so simple and uncluttered. Perhaps their decision to remove pinch & zoom was related to that idea.
-
IPad can't get in the internet via a WPA2 Enterprise setup
I've seen some similar posts and no real answers. My Office just got set up with Wireless, it's cisco gear and using RADUIS to authenticate. What they told us to do on the windows boxes was this:
Connect to the SSID
use WPA2 Enterprise Authentication
TKIP Encryption
Use PEAP Authentication
Uncheck the "Validate Server Certificate"
Authentication Method is EAP-MSCHAP v2 on the PEAP properties screen
Following these instructions on Windows 7 I can get on the network.
I tried this on my iPad:
connected to the network
selected WPA2 Enterprise
It Prompted my for my login/password
I entered them....
Then I got a certificate and it asked me to accept/install it, and I did
Then it connects to the access point and gets a signal
Even though I am connected and authenticated I can't get on the internet, and I get no IP address. Not a DHCP issue since other devices work.
Any ideas on alternate configurations, or what I'd need to do with the iPhone Configuration Utility to get this working?"Unsupported" device - I've heard that before, too many times... =)
So after thinking on everything you've tried, it's safe to say that your AP is running PEAPv0 with EAP-MSCHAPv2 for Authentication. This is good news - as it is probably the most widely used Enterprise WiFi configuration, iOS devices should absolutely be compatible with this. Getting a non-domain XP PC connected was a great idea, as I have discovered that Windows XP is kind of "loose" in the way it handles PEAP certificates - it will accept any certificate given to it by a RADIUS server without question. Undoubtedly a big security hole, but it does have the advantage of being "user friendly." I don't think Apple's implementation is quite as loose, so even though you are manually accepting one certificate, you probably need more to complete the chain of trust required for your device to authenticate the server. This is a requirement for PEAP to function.
So at this point, I think your best bet would be to migrate over to the Credentials tab. If you're running the iPhone Config Utility on a PC which connects to the AP, you already have the certificates in your trusted certificate store - so simply hit the add button and add any relevant certificates. For example, if your domain is named "corporate", import any certificates bearing that domain. Once you've done this, head over to the Trust tab under WiFi and check off your newly imported certificates as being trusted for your connection.
In addition, if you can figure out what the name of the RADIUS server on the other end of the AP is doing the authentication, add it under "Trusted Certificate Names" - if you don't know it, you can also add a wildcard like "*.corporate" to trust any servers in your domain. This shotgun approach is probably your best bet for making it go initially.
You will know this is all working when you no longer get the dialog on your iPad to accept the certificate, and hopefully, you get an IP address.
We're truly in the thick of it now, and this is my last idea - so if this does not work, we will need to call on those stronger than I with iOS networking... or, you can call up your IT department and start the conversation off with the words "I bet you can't figure this out" - that always gets IT people going =)
Best of luck!
Sources:
http://howto.techworld.com/mobile-wireless/3451/use-peap-for-wireless-authentica tion/
http://images.apple.com/ipad/business/pdf/iPadDeploymentScenarios.pdf -
Ok. so i did a search and didn't come across any other problems like the one I'm having.
Let me start off by stating that my laptop is an ibook g4 bought feb, '06 (yes the apple care just ran out).
I'm having a problem connecting to the internet on my ibook, running through a d-link wireless router. I'm using my imac to connect to the internet currently (which works fine by the way). It also is connected through the wireless router.
My ibook has a strange ailment. I open up Safari and all I get is a blank screen, the page is trying to load but the status bar is going no where and does the same in Firefox. So first, I opened Network diagnostics, but the computer freezes and I have to do a hard shutdown. (holding the power button). Next, I tried Disk utility. Verified Permissions, Repaired Permissions, everything is fine. I tried to Verify Disk, and again the computer freezes, will not let me force quit and I am forced to do another hard shutdown. I do the thing where you hold down some key while you're starting up to get into the disk utility so I can repair the disk. This returns clean as well. I downloaded techtool off of my Applecare disk. Did the tests, everything passes. So what's the deal?? I've tried to reset the pram. I even did the Apple Hardware test, everything passed.
I thought it could be my Airport card? It recognizes that there is an internet connection in the top right corner, I even have great signal strength (mostly because I've tried this sitting right next to the router). But still, I can't connect to the internet. Any one have any ideas? I don't know what else to try! Please help!so i can't believe i didn't try to connect it directly to the router with the ethernet cord. This actually worked. But it still didn't solve my wireless problem. I'm not willing to let my laptop become a desktop. I'm already wired to a plug b/c the battery is slowly dying and has a life of about 5 minutes. I'm not willing to give up my wireless internet too.
I guess now it's got to be the airport card? how do I confirm this? and if it is how much would a new one cost and can I install it myself?? -
Extreme (b/g/n) can't connect to the internet
my iMac has no problem seeing my airport extreme (b/g/n), but I can't connect to the internet.
I have tried soft / hard reset & factory reset as well, none of them worked. The extreme just keep flashing its amber light.
On my iMac, I have full signal bars, so recognizing the extreme is not a problem. The only thing I find strange is that the IP address (the one assigned by my ISP) is 0.0.0.1.
I tried connecting through an Ethernet cable and it didn't have any problem, so it's not my ISP. The only thing I can thing of is that the extreme somehow is having trouble recognizing that assigned IP and that's why I can't get connect to the internet.
Anyone suggestion? Is my extreme broken? If so, can it be fixed? Please help.Problem solved!
Every time, I feel so stupid once I find out the answer to my problem.
Here it is from another post by 'dwbird':
"Solution: I found that the service name (optional on the setup) may be optional but if your service doesn't require it and you put a service name in the block it prevents the system from working, hence cannot find the PPoE Server and also cannot get an IP address assigned. Guess the moral of the story is that if it is not absolutely required don't fill in any "optional" blocks"
I deleted the name of my ISP and everything works just fine, the stupidest thing is that this is not the first time...
maybe Apple should consider putting a reminder/warning underneath this OPTIONAL service name field.
Maybe you are looking for
-
Suppress Decimals for CURR field in ALV Grid based on condition
Hello All, I am displaying records in ALV Grid. For a Company Code, I get the Currency Code from table T001. If the Currency is JPY, I want to display the value of CURR field without decimals. For example: if the value is 200.00, I want to display on
-
NLS:4: Cannot open message catalog TMADMIN_CAT, Solaris Container
Hello, Can someone please help me ? I have used Tuxedo 8 for many years on Solaris 8 servers, however we have now ported our installation to a Solaris 8 container on a Solaris 10 server. The server was ported using a flar image from the source server
-
Solaris Express Zone install error with SUNWiiimr and SUNWcnetr
Hi all, I got these errors when installing a new zone on a Solaris Express 1/08 (5.11) on a x64 box: Installation of these packages generated errors: SUNWiiimr Installation of these packages generated warnings: SUNWcnetr The zone creation log shows:
-
Sending a script in mail (outside SAP)
Hi, Currently i am sending my mail to ids in SAP. so that i am able to do straightaway by giving device as 'mail'. please check code below. CALL function 'OPEN_FORM' EXPORTING APPLICATION = 'TX' ARCHIVE_INDEX
-
Hi I'll write here too as this is the first time I've done this too. I'm new to ipad and I'm having trouble with icons appearing on my ipad after I have downloaded them. These are all tv based -sky go app, iplayers and on demand. I have installed the