My software on my MacBook Pro won't update?
I have tried to update my software for my computer by going to the apple menu and selecting software update. My computer restarts, but when it turns on, nothing has changed. Does anybody have the same problem or knows what to do about it? Thank you
Upgrading from Snow Leopard to Lion or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99.
If you sign into the App Store and try to purchase Mountain Lion but the App Store says your computer is not compatible then you may still be able to upgrade to Lion per the following information.
A. Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mountain Lion - System Requirements
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
7. Xserve (Early 2009) - Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table - RoaringApps.
For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion.
B. Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.
Similar Messages
-
Macbook pro EFI firmware Update 1.4 won't work, neither will software
I got two probs, not sure how related they are.
#1 is that I can't successfully do the macbook pro EFI firmware Update 1.4. My computer was bootcamped and kept restarting in windows - thus the update was not completed - the completion bar would pop up for an instant - i could not see if it had completed, i don't think so... and then it would flash back to black, and restart again. Upon restart the firmware update was still there as needing to be updated.
I've now taken bootcamp off and restored a single drive. It's doing the same thing and hasn't updated.
#2 is that DVD studio pro will not boot anymore after it has been working with no problems for over a year. Nor will Motion run although it has never worked. I have tried reinstalling multiple times and just today went to delete the preferences. No luck.
Any suggestions or better yet, solution, I'm ever so grateful.
Cheers
-kI have the same problem. It's also important to note that, in my case, I'm running 10.7.2 (11C74), but it's a firmware update, so it shouldn't really matter if I'm running a beta version of Lion, should it?
-
My Macbook Pro won't boot up, only in safe mode!
Help, my macbook pro won't restart, only in safe mode! and it seems that safe mode has plenty of implications for use. my usb memory stick doesn't seem to be recognized while in safe mode. I was doing a cleanup on mackeeper just after I downloaded a trial version of microsoft office mac. The trial wouldn't work properly so I deleted it and decided to do a cleanup with mackeeper. than the mac froze while mackeeper was doing it's cleanup and the screen flashed black a few times. Ever since it won't boot up unless I use safe mode. Also, I downloaded the most recent updates while in safe mode but it doesn't seem to be recognizing that I already downloaded them because software update is still telling me that I have 6 updates. So I am horribly confused at this point. Please help, I need this laptop to do report cards (it's a good thing I got an extension). thanks
Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in safe mode.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
The commands may line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click the line of text below to select it. Copy the selected text to the Clipboard (command-C). Then click anywhere in the Terminal window and paste (command-V).
find /Sy*/L*/Ex* -type f -name Info.plist -exec sh -c '/usr/libexec/PlistBuddy -c "Print :CFBundleIdentifier" "$1" 2> /dev/null | egrep -qv "apple|Accusys|ArcMSR|ATTO|CalDigit|HighPoint|hp-fax|JMicron|print|SoftRAID|stex" && echo ${1%*.kext/*}.kext' {} {} \;
Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
Step 2
Repeat with this line:
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 3
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, these steps are all copy-and-paste — no typing. Also remember to post the output.
You can then quit Terminal. -
Macbook Pro won't print the first page of any file in any application.
Problem: My Mid-2009 Macbook Pro won’t print the first page in Microsoft Word, Sibelius 6, or in Adobe Reader. My printer is an old Canon MP480 that’s worked for almost 2 years perfectly. As well, the “print to pdf” function results in the same error. However, if I open a new user account it all works fine. To change user accounts would be an extreme hassle though so, if possible, I would like to first remedy this one.
Recent changes: the motherboard of my computer was replaced about a week and a half ago. I printed a lot of stuff from Word two days ago and that worked fine but, already then the print to pdf function was cropping off the first page. At the time, though, I accredited the issue to the word documents being filled with pictures of sheet music that I was printing instead of text.
Things I have tried:
Updated Mac software
Repaired Disc Permissions in Disk Utility
Checked for new printer drivers/firmware
Reset the PRAM (http://support.apple.com/kb/ht1379.)No but it's not a printer-related issue because the "Print to PDF" function also leaves out the first page.
-
My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Macbook pro won't boot after installing update 10.9.3
macbook pro won't boot after installing update 10.9.3
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test. -
MacBook Pro won't start after I completed my first backup using TimeMachine
Hello,
My MacBook Pro won't restart after I did my first TimeMachine backup. I tried in SafeMode but no luck. My MacBook Pro is a 2009 early version running Snow Leopard. Please help.
Thanks,
SereyI have managed to get into my computer through the OS X install disk but now my wi fi hardware is gone. Ie no airport.
When I try to re install the airport extreme wi fi base station software it tells me it can't be installed as this version of Mac OS X (Lion) on is volume is not supported.
Not even an Ethernet cable gets me on line. In system preferences when I do a network diagnostic all I get is the spinning disk. Again, any ideas how to get around this?
Thanks -
Macbook Pro won't start properly... keeps restarting without chime!
Macbook Pro won't start properly... keeps restarting without chime!
Late 2007 Macbook pro. OS upgrade worked great for me.
I have had this problem on and off for a month or so. I simply cannot figure out what the issue is. I have tried poerup with and without AC power and with/without battery installed.
Starting in Safe mode does not help.
Trying to start with a disk does not help.
It sort of seems like it might be an internal power issue or GPU issue.
It also feels sort of like a software compatibility issue since my Macbook Pro gets reallly slugish for no apparent reason sometimes and IU have to restart.
I have three different anti-virus programs so I doubt it is a virus issue.
I noticed all this start after I did a Mountain Lion upgrade and then tried to start up VMware Fusion. Fusion seemed to just bog down the computer horribly but did not cause a system crash.
I need to edit an important sequence on Final Cut Pro and don't want it to freeze me out!
Anyone who has had this problem and resolved it please let me know
God blessSystematically run through this list of fixes.
..Step by Step to fix your Mac
If it doesnt chine it doesn't mean much, the mute could be on or you installed a anti-chime software. -
My Macbook Pro won't print with my HP Photosmart 7515. I get the following message, " Print file was not accepted" Printer does work with our PC?? Checked for software updates and are none. Talked with HP help and they say it's an Apple problem
I noticed that you said you uninstalled the printer, but you didn't mention resetting the print system. Resetting the print system will reset the drivers the Mac has installed and make them work like they should. Give this a try and see if it gets the printer working like it should. The document below will expalin more about doing this.
Basic Printer Troubleshooting Steps for Mac
If that doesn't help, see if you are using the AirPrint driver, or the printers driver. By default 10.8 uses the AirPrint driver if the printer supports it, so I'm betting that's the driver you're using. If it is, try using the driver for the printer itself. To do this, access Print and Scan. Click the + sign to add a new printer. Select the printer from the list. Click the dropdown next to Use and select the 7515's driver. Let me know what happens.
I am a printer tech for HP. -
Attn: macbook pro won't start up past grey screen NO MATTER WHAT
my macbook pro won't start up past the grey screen, NO MATTER WHAT I DO. i've searched all the discussions on this, and NOTHING WORKS. nothing caused this either - i was just browing the internet and using ichat, and my computer shut down, and that is when this started.
I am EXTREMELY disappointed with this bullstein. My computer works great, etc., and I support mac and apple to the nth degree, but then some stupid crap like this happens and I can't use my computer at all. I have to use my sister's **** ibook g3 to even do this.
PLEASE HELP. do NOT post what you have already posted in the other discussions, and i've already been welcomed to the boards. I can't go to an apple store because i'm on vacation in new mexico for the summer, and there no stores anywhere near here. is there any real advice around here? I need to use my computer. That is why I spent close to $4,000 for it with upgrades and software.where can i get an install disc for the macbook pro?
You really need to use the one that came with your MBP. If you don't have it, a retail Tiger OS X disc should work.
also, could an archive/install potentially free up some harddrive space on my computer?
No, it will actually use more space, so you will need at least 6G of free space. To clean your hard drive, use WhatSize.
WhatSize >>
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
An Apple User Group -
My MacBook Pro won't turn on, what's wrong?
My MacBook Pro won't turn on. What's wrong?
gobetty wrote:
My MacBook Pro won't turn on. What's wrong?
Depends upon what you mean by it not turning on, there are various causes.
Is the power button pressed and nothing happens? Disconnect all other devices, then a SMC and NVRAM reset.
Is there a white screen and nearly nothing? A hosed EFI firmware.
Is there a grey screen and a loading bar that gets stuck? Either a failed firmware update or corrupted drive/OS X.
Is there a grey screen with a spinning wheel? Bad third party or Apple at boot kext file.
Are you loading but not able to log in? Possible corrupt third party software designed to startup upon login.
..Step by Step to fix your Mac -
My MacBook Pro won't load any websites on Safari (except this site, Facebook and Google). Opera and Mozilla Firefox won't load any sites whatsoever. I already did the "Reset Safari" several times, restarted the computer half a dozen times, and I can't find this alleged "caches.db" file to delete. I virus scanned the computer with Sophos, Avast, and iAntiVirus and it looks clean.
Is iAntiVirus the best virus protection to use for a MacBook?
The best anti-virus protection is your own common sense, and what you already bought and paid for with your Mac. Third party products such as "iAntiVirus" convey no additional benefit, and as you already determined are very capable of causing trouble.
OS X already includes everything it needs to protect itself from viruses and malware. Keep it that way with software updates from Apple.
A much better question is "how should I protect my Mac":
Never install any product that claims to "speed up", "clean up", "optimize", or "accelerate" your Mac. Without exception, they will do the opposite.
Never install pirated or "cracked" software, software obtained from dubious websites, or other questionable sources. Illegally obtained software is almost certain to contain malware.
Don’t supply your password in response to a popup window requesting it, unless you know what it is and the reason your credentials are required.
Don’t open email attachments from email addresses that you do not recognize, or click links contained in an email:
Most of these are scams that direct you to fraudulent sites that attempt to convince you to disclose personal information.
Such "phishing" attempts are the 21st century equivalent of a social exploit that has existed since the dawn of civilization. Don’t fall for it.
Apple will never ask you to reveal personal information in an email. If you receive an unexpected email from Apple saying your account will be closed unless you take immediate action, just ignore it. If your iTunes or App Store account becomes disabled for valid reasons, you will know when you try to buy something or log in to this support site, and are unable to.
Don’t install browser extensions unless you understand their purpose. Go to the Safari menu > Preferences > Extensions. If you see any extensions that you do not recognize or understand, simply click the Uninstall button and they will be gone.
Don’t install Java unless you are certain that you need it:
Java, a non-Apple product, is a potential vector for malware. If you are required to use Java, be mindful of that possibility.
Java can be disabled in System Preferences.
Despite its name JavaScript is unrelated to Java. No malware can infect your Mac through JavaScript. It’s OK to leave it enabled.
Block browser popups: Safari menu > Preferences > Security > and check "Block popup windows":
Popup windows are useful and required for some websites, but popups have devolved to become a common means to deliver targeted advertising that you probably do not want.
Popups themselves cannot infect your Mac, but many contain resource-hungry code that will slow down Internet browsing.
If you ever see a popup indicating it detected registry errors, that your Mac is infected with some ick, or that you won some prize, it is 100% fraudulent. Ignore it.
Ignore hyperventilating popular media outlets that thrive by promoting fear and discord with entertainment products arrogantly presented as "news". Learn what real threats actually exist and how to arm yourself against them:
The most serious threat to your data security is phishing. To date, most of these attempts have been pathetic and are easily recognized, but that is likely to change in the future as criminals become more clever.
OS X viruses do not exist, but intentionally malicious or poorly written code, created by either nefarious or inept individuals, is nothing new.
Never install something without first knowing what it is, what it does, how it works, and how to get rid of it when you don’t want it any more.
If you elect to use "anti-virus" software, familiarize yourself with its limitations and potential to cause adverse effects, and apply the principle immediately preceding this one.
Most such utilities will only slow down and destabilize your Mac while they look for viruses that do not exist, conveying no benefit whatsoever - other than to make you "feel good" about security, when you should actually be exercising sound judgment, derived from accurate knowledge, based on verifiable facts.
Do install updates from Apple as they become available. No one knows more about Macs and how to protect them than the company that builds them.
Summary: Use common sense and caution when you use your Mac, just like you would in any social context. There is no product, utility, or magic talisman that can protect you from all the evils of mankind. -
My MacBook Pro, won't start up / log in... Help!!
My MacBook Pro, won't start up. Takes ages to turn on, eventually the password screen comes up, I enter my password (which is correct and hasn't changed) press return, and looks like it will load, then goes back to the login screen... Help!!
Run through this massive list of user capable fixes tailored to isolate and identify where your problem(s) are, get your machine working again or call a local PC/Mac software repair and data recovery shop, if it's hardware problem, take it to Apple.
Step by Step to fix your Mac -
MacBook Pro won't stay asleep with external monitor attached. When sleep is selected from the Apple menu the computer will go to sleep only to continually wake up...go back to sleep...wake up...etc. every few seconds. This only happens when using the external monitor. Does anyone have any suggestions?
Mine does that too. The worst thing is when it goes to sleep, then wakes up and keeps running while the lid is closed and it is wrapped up in a case. I am afraid when the hot weather comes it is going to burn up. I am hoping Apple fixes it in the software or they may have a melted MBP to replace.
Then when I open the lid it is crashed running at fill tilt, pumping out heat to beat the band. I am forced to hold the button down and reboot.
I wiped my hard disk and reinstalled my OS, but it didn't help. I reversed my OS to 10.5.0 and it solved the DVI problem but still won't sleep. This post will probably be deleted by Apple, they did it a few days ago. I just don't know what to do, and I consider myself a real Apple expert. Just hoping you realize you are not the only one. -
Macbook Pro won't connect to wireless printer anymore suddenly
Suddenly my Macbook Pro won't connect to my HP Photosmart B210e Printer. I have tried adding it via IP address, it worked but I can't print anything. It says the printer is busy and idle? I updated the software and drivers. All other computers and devices in my home connect just fine. It is connected to our wireless router as is my laptop.
I have searched online and done all the solutions I could find and nothing is working. VERY frustrated as I have to log onto my Dell to print anything.
Thanks in advance for any help!
Kim"It says the printer is busy and idle?"
System Preferences>print and Scan. What is the staus of the printer? Green light for idle or yellow light for in busy? Have you tried power down the printer and paowering it back up?
Maybe you are looking for
-
How to use your credit to buy music
Hello Everyone, this is more than the answer to a question I had and unsuccessfully finding answers that did not resolve my problem. I made a couple of comments one some of those answers basically complaining as how poor Apple Support was by leaving
-
My new computer is 64-bit running Windows 7 pro, SP1 and Microsoft Office 2010 Pro Plus 32-bit My phone is a 4S runing iOS 6.1.3 Very frustrated now that I have recently installed itunes and outlook on this new computer. Everything worked perfectly
-
Event firing at item added and item updated in event receiver?
Hi All, I have created event receiver on item added & item updated on document library. 1) On Item Added i am updating document library Title column with document Name and i have metadata for the file. 2) On Item Updated i am move that file with meta
-
Thumbnails Broken in Elements 11 (Mac User)
I installed Photoshop Elements 11 (with Camera Raw 7.4 update) onto my Mac (OS 10.7.5). Thumbnails do not display correclty. Some display just a generic image. Even new photos (from Canon T5i) do not display thumbnails correctly. The thumbnails f
-
HT1331 Please help Windows user find disk on network...I'm stumped
I'm running Windows Vista and Windows 7 on another PC. Neither can even connect with the AIrPort Extreme by typing 10.0.1.1 in my browser. It shows up fine with AirPort Utility, it's IP is in fact 10.0.1.1. Internet works, file sharing from PC to PC