My Sony Bravia KDL-40CX520 does not have a coaxial input for my digital antenna...

What can I do if my tv has no coaxial input for my digital antenna?
Thanks...
Update: I found a Euro connector which got me the connection I needed. However, I am still unable to locate any digital antenna channels within the 50 mile radius of the antenna/w amplifier.

HI nikkijordyn,
Welcome to the Sony Community!
IMPORTANT: Before we proceed further, please check the supplied manual of the TV to confirm if the television is set to NTSC or PAL. US is under NTSC video system.
If the TV is set to NTSC, please perform the troubleshooting steps below:
Upon checking the specifications, this TV has RF input that connects to your cable or over-the-air antenna.
If no digital channels can be found, then there may not be any digital channels currently available. Perform an Auto Program to have the TV search for any available digital channels.
Perform Auto Program, please check the steps below:
Press Home button on the remote
Go to Channels and Inputs
Select Auto Program
NOTE: We cannot guarantee the functionality or compatibility of those 3rd party devices.
If my post answers your question, please mark it as "Accept as Solution"

Similar Messages

How can I do live streaming with a Mac Book Pro 2011, using a new model of Sony HD camcorder which does not have firewire out/input? it comes only with a component video output, USB, HDMI and composite RCA output?

I need to do live streaming with a Mac Book Pro 2011, using a new model of Sony HD camcorder (http://store.sony.co...ber=HDRAX2000/H) ..this camcorder model does not have firewire out/input ..it comes only with a component video output, USB, HDMI and composite A/V video output..
I wonder how can I plug this camcorder to the firewire port of my laptop? Browsing on internet I found that Grass Valley Company produces this converter http://www.amazon.co...=A17MC6HOH9AVE6 ..but I am not sure -not even after checking the amazon reviews- if this device will send the video signal through firewire to my laptop, in order to live streaming properly? ..anyone in this forum could help me please?
Thanx

I can't broadcast with the built in iSight webcam... how would I zoom in or zoom out? or how would I pan? I've seem people doing it walking with their laptops but that's not an option for me... there's nothing wrong with my USB ports but that's neither an option to stream video because as far as I know through USB you can't connect video in apple operating systems ..you can for sure plug any video cam or photo camera through usb but as a drive to transfer data not as a live video camera... is by firewire an old interface developed by apple that you can connect all sorts of cameras to apple computers... unfortunately my new sony HDR-AX2000 camcorder doesn't have firewire output...
thanx

The security database on the server does not have a computer account for this workstation trust relationship

When I try to log on to my DC it says "The security database on the server does not have a computer account for this workstation trust relationship". It won't let me log on. I installed another server server 2012r2 (its virtual )
and I can get to ADSI edit.
I think what happened was I had a pc that could not connect without unplugging the network cable. So I found this fix
FIX: “The security database on the server does not have a computer account for this workstation trust relationship”2032011
I’ve seen a lot of solutions, or suggestions rather, with regard to the error in the title of this post. In my experience, the problem can almost always be resolved without extra domain add/removes and reboots, which is the most prevalent solution I have
seen around. Usually, this issue is due to a mismatch between attributes of the computer account in Active Directory and those values on the system itself. Here are the steps I take to fix this issue when it crops up:
Open up Active Directory Users & Computers pointed to the domain the computer account resides in
From the “View” pull-down menu, make sure that “Advanced Features” is checked
Navigate to the part of your organizational unit (OU) structure where the computer account for this server resides
Open the Properties for the computer object
Choose the “Attribute Editor” tab on the Properties dialog box
Check the Attributes dNSHostName & servicePrincipalName – anywhere that a fully qualified hostname is specified (e.g. myserver.mydomainname.com), make sure that the entry matches the hostname
you have configured when you go here on your server: Start -> Computer -> Right-Click, Properties -> Change Settings (under “Computer name, domain… settings”) -> Full Computer Name
As an example, for a fictitious W2K8 R2 server whose Full Computer Name is “srv1.mydomainname.com”, these attribute/value pairs should be in Active Directory:
dNSHostName:
srv1.mydomainname.com
servicePrincipalName:
HOST/SRV1
HOST/srv1.mydomainname.com
RestrictedKrbHost/SRV1
RestrictedKrbHost/srv1.mydomainname.com
TERMSRV/SRV1
TERMSRV/srv1.mydomainname.com"
Not reading it carefully I add a computer with the same name as the pc having the issue and followed the above. The problem is that I did not notice that the spn did not want the name of my server (serv1) but the name of the trouble
pc.
dcdiag output
PS C:\Users\administrator.TOM> dcdiag.exe
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
***Error: DC3 is not a Directory Server. Must specify /s:<Directory Server> or /n:<Naming Context> or nothing to
use the local machine.
ERROR: Could not find home server.
PS C:\Users\administrator.TOM> dcdiag.exe /s:DC2
Directory Server Diagnosis
Performing initial setup:
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site\DC2
Starting test: Connectivity
The host 9e0dca7a-d017-445a-b354-adee5ff53d48._msdcs.TOM could not be resolved to an IP address. Check the DN
server, DHCP, server name, etc.
Neither the the server name (DC2.TOM) nor the Guid DNS name (9e0dca7a-d017-445a-b354-adee5ff53d48._msdcs.TOM)
could be resolved by DNS. Check that the server is up and is registered correctly with the DNS server.
Got error while checking LDAP and RPC connectivity. Please check your firewall settings.
......................... DC2 failed test Connectivity
Doing primary tests
Testing server: Default-First-Site\DC2
Skipping all tests, because server DC2 is not responding to directory service requests.
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : TOM
Starting test: CheckSDRefDom
......................... TOM passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... TOM passed test CrossRefValidation
Running enterprise tests on : TOM
Starting test: LocatorCheck
......................... TOM passed test LocatorCheck
Starting test: Intersite
......................... TOM passed test Intersite
PS C:\Users\administrator.TOM> regsvr32 schmmgmt.dll
PS C:\Users\administrator.TOM> netdig /fix
netdig : The term 'netdig' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ netdig /fix
+ ~~~~~~
+ CategoryInfo : ObjectNotFound: (netdig:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM> Setup /PrepareSchema
Setup : The term 'Setup' is not recognized as the name of a cmdlet, function, script file, or operable program. Check
the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ Setup /PrepareSchema
+ ~~~~~
+ CategoryInfo : ObjectNotFound: (Setup:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM> netdiag /test
netdiag : The term 'netdiag' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ netdiag /test
+ ~~~~~~~
+ CategoryInfo : ObjectNotFound: (netdiag:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM> nslooup
nslooup : The term 'nslooup' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ nslooup
+ ~~~~~~~
+ CategoryInfo : ObjectNotFound: (nslooup:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
PS C:\Users\administrator.TOM>

Ok fixed.
At a elevated cmd prompt run ;
C:\Users\administrator.TOM>setspn -x
As you can see the DC serv1 had duplicate SPNs.
Checking domain DC=TOM
Processing entry 1
HOST/serv1.TOM is registered on these accounts:
CN=SERV1,OU=Domain Controllers,DC=TOM
CN=C00049,CN=Computers,DC=TOM
{14E52635-0A95-4a5c-BDB1-E0D0C703B6C8}/TOWN-HBWJ29ZOQC is registered on these ac
counts:
CN=Administrator,CN=Users,DC=TOM
CN=TOWN-HBWJ29ZOQC,CN=Computers,DC=TOM
{14E52635-0A95-4a5c-BDB1-E0D0C703B6C8}/town-hbwj29zoqc.TOM is registered on thes
e accounts:
CN=Administrator,CN=Users,DC=TOM
CN=TOWN-HBWJ29ZOQC,CN=Computers,DC=TOM
RestrictedKrbHost/serv1 is registered on these accounts:
CN=C00049,CN=Computers,DC=TOM
CN=SERV1,OU=Domain Controllers,DC=TOM
RestrictedKrbHost/serv1.TOM is registered on these accounts:
CN=C00049,CN=Computers,DC=TOM
CN=SERV1,OU=Domain Controllers,DC=TOM
found 5 groups of duplicate SPNs.
Went to the computers OU and changed computer c00049 to the correct SPN. Now I have a new issues, I'll start a new thread.

I just purchased the apple tv, i have an older tv that does not have an HDMI input. is there a converter i can get because the itv only have an HDMI output ? help.

i just purchased the apple tv, i have an older tv that does not have an HDMI input. is there a converter i can get because the itv only have an HDMI output ? help.

Welcome to the Apple Community.
There are hardware converters that will convert HDMI to various other types of output, however there are some issues with doing so that you should be aware of.
HDCP
HDCP compliant converters will not allow you to watch HDCP protected content such as that from the iTunes Store. Non compliant converters exist but we cannot discuss them under the Terms of Use for these communities.
Resolution and aspect ratio
I'm not aware of any converters that will scale the output from the Apple TV, any TV or projector which is used will need to be widescreen and support resolutions of 720p.

File transport does not have read/write privileges for receive location???

Hi all.
I try to read an EDI-file from a file location.
In configured the receive location but when I enable it I get an error message in the log saying:
File transport does not have read/write privileges for receive location "Location" (Event ID: 7183)
The location is correct (I used the browse option) and the folder is shared with all users (full access for everybody).
How can I get rid of this error

There can be many reasons for this error. First of all try the KB article http://support.microsoft.com/kb/888498 . Then try the solution on this link http://bluebiztalk.blogspot.com/2008/05/file-transport-does-not-have-readwrite.htmlAbdul Rafay
http://abdulrafaysbiztalk.wordpress.com/
Please mark this as answer if it helps

I have bought a new laptop which does not have a Disk Drive for CDs. How can I load my Acrobat Pro X on to this computer

I have bought a new laptop which does not have a Disk Drive for CDs. How can I load my Acrobat Pro X on to this computer

Download it from https://helpx.adobe.com/acrobat/kb/acrobat-downloads.html

Can you upload Logic pro onto an external drive? Because my G5 does not have 50 GB available for installation, Can you upload Logic pro onto an external drive? Because my G5 does not have 50 GB available for installation

Can you upload Logic pro onto an external drive? Because my G5 does not have 50 GB available for installation, Can you upload Logic pro onto an external drive? Because my G5 does not have 50 GB available for installation

Logic 9.0.2 is the last version that runs on a G5 - 9.1.x is Intel only.
If you have only 50 GB left on your system drive, you should consider it full. Get an external drive and move your music, movies and photo's to it, and delete them from your system drive to free up space.
The free space on the system drive is being used by the OS to offload RAM, rule of thumb is to keep at least 20 % of the drives' capacity free. When you have less and less free space, your Mac will eventually become very slow (many "beachballs").
I believe the current Logic Package has version 9.1 on it, be sure you have the correct (9.0) version...

This server does not have the module needed for interpreting traces

I wan to use the Trace Control function of the Exchange Troubleshooting Assistant. I specifically want to look at the transactions of a particular user. When starting the function I get the message, "This server does not have the module needed for interpreting traces." I find nothing to tell me what the module is or where to get it.
Specifically, I have a Macintosh user (bigwig in my organization) that insists on using Apple's 10.6 Calendar program, and constantly complains that his calendars are different between his 3 Macs and his iPhone. He claims to have put a calendar item on one machine, now it appears nowhere. And I have no way of proving what is going wrong. He hates Outlook and refuses to use it, he hates Entourage and refuses to use it. The local database for Entourage kept getting fouled up to the point that we kept having to delete this account and readding it to force the recreation of the database. The database tool never fixed the problems and of course he did a lot of customization that got destroyed every time we deleted the account settings and added them back.
I really want to run the tool for a while and see if there is actually some transaction actually happening on the server side, so I would like to have these traces and be able to view them.
SnoBoy

See
http://blogs.msdn.com/b/dvespa/archive/2011/05/27/how-to-use-extra-to-troubleshoot-rpc-client-access-issues.aspx.
Just click on ok and proceed with set trace manually.
Svetozar Petrović

I movie 11 does not have a special feature for subtitles?

i movie 11 does not have a special feature for subtitles?

No, not like you would find on the Windows PC for example Aegisub. That is a very well made open source sub-title editor. What iMovie has are embedded or hard coded subtitles burned right into the video frames after you Share the movie (exporting it really) to the Desktop. There are some title choices that can mimic the sub-titles you see in the movies, but you don't get the timing accuracy required to to real sub-titling, and that's what a program like Aegisub provides, timing, two rows of text, all kinds of different options to not just add but refine the titles.
The closest you can get to a sub-title in iMovie '11 is Lower Third, and Lower options unde the Titles toolbar. (the letter T tool)

HT201263 My itouch does not have an update option for the os

I am trying to set up icloud and it says I must have 5.0 on my device bt the itouch does not have the software update option shown it the directions on the apple website.

Connect to your syncing computer and start iTunes. From the summary screen, check for updates. If you have a 2nd generation iPod, it can not be upgraded beyond 4.2.1.

Trying to find a record that does not have an event created for it

Post Author: tzinser
CA Forum: Formula
A little background on how it works....
We create a record, and everytime it is created, a number of "events" within that record are automatically created. The specific event I am trying to run a report on is "REC". I can run a report and get the information entered into the REC event no problem, but my problem is that if someone deletes the "REC" event it does not show up in my report.
So my question is, what is the best way to write a function that displays all records that have the "REC" event, and all records that the "REC" event is missing.
I'm using the generic funtion {EVENT.EventCode} = "REC" right now....any suggestions?

Post Author: tzinser
CA Forum: Formula
Okay, I left off a lot of important information...
I'm using two tables
TWDATA
EVENT
From TWDATA I'm pulling the fields TWDATA.OrderNumber and TWDATA.DisbursementDate
From EVENT I'm pulling the fields EVENT.EventCode and EVENT.CompletedDate
The two tables are linked by OrderNumber.

I have purchased Quicktime Pro and entered the registration key but does not operate. Apple does not have a support tab for this so I'd appreciate any help. I have Windows 7 Home.

I have purchased Quicktime Pro and entered the registration code. It indicates at it has been installed, but it does not run. Any suggestions?

The trim to selection function is available and it appears to be working. For now, I seem to be operable as Pro even though the header doesn't say so. Thanks.

HT3625 But my Mac in the Sound Input menu does not have the "Use audio for" menu option.

I want to use the audio port in my MacBook Pro 13 to record stereo sound, under the Preference>Sound> Input menu, there is no option of "use audio for".

Mid 2012 Macbook Pro 13" do not have audio in through the headphone jack.
The 13" with retina and the 15" have it.

HT4623 my daughter was trying to do an ios update on her new ipad mini it now says to plug into itunes she does not have a seperate computer for that, the reason for the ipad can anyone tell me how to fix this or how to reset the ipad

tried to do an ios update the ipad mini is now asking to plug into itunes, have now seperate computer to do this can not get any other screen to come up on ipad can the ipad be reset or how do I fix this

If it's showing the connect to iTunes screen then it sounds like it's gone into recovery mode and will need to be connected to a computer's iTunes in order to be reset. Does neither she nor you have a computer, and if she hasn't has she been backing up to the cloud instead ?
Depending upon what country that you are in, and whether content is still in the store, she might be able to re-download some/all of her downloads via the Purchased tabs in the App Store and iTunes store apps

I have an SD card that my husband uses for a trail camera. The camera does not have a delete function for the pics, so I put the SD card in our MAC and we can view the pics but when I go to delete them it says that the files cant be deleted. What can i do

My husband has an SD card he uses for his trail camera. We put it in our mac book pro and can look at the pictures but when I go to move them to the trash it tells me that the files can't be moved to the trash because they cant be deleted. I have Nikon camera software on my mac and it pics up and asks if you want to import the pics and if you want them deleted from the devices afterwards. I tried that but I get a message afterwards that says that some files were not able to be deleted. When I go to check, none of them were deleted. How can I clean of the SD Card? I do have a camera I could stick it in, it would just be nice to know how to do it from my mac. Also, the files are jpg. if that matters.

AFAIK cameras offer their own built-in format utility for inserted SD cards. You should use that. Otherwise, refer to the manual that came with your camera to determine precisely how your SD cards need to be formatted to work properly. Personally, I'd suggest Partition Scheme: MBR, and Filesystem: FAT32.
Try to limit the number of formats you perform on the SD cards, though, as you're reducing their lifespan. I believe formatting causes re-writes to a portion of the SD card that has fewer read/write cycles than the rest of the card as a whole.

My Sony Bravia KDL-40CX520 does not have a coaxial input for my digital antenna...

Similar Messages

Maybe you are looking for