My System do not boot

Hi to the people on the forum, I have a Lenovo 3000 J110 series, my system is too slow having a core 2 duo processor, I try to find something on the bios to try to make more faster, I find cpu max id was disable, I enable it, but after of thease my system do not boot more, try to put the bios in short whith teh jumper and nothing, I try to clear the bios leavion the system with ot battery for 3 days and nothing, I test the presessor and the memory in other mobo and work fine ???, the system when boot swoh the Lenovo logo and the message "staring system " thah is all, the can stay all day showing this message, where is the problem ????
Thanks in advance.

It seems that you have changed the speed/voltage and may have burn out something. But since it does post it does not seem to be the CPU nor MoBo. It's possible to be the HDD or Ram. Try booting the pc with the HDD disconnected, then try moving the Ram around.
IT Specialist and Consultant
Lenovo Tablet Evangelist
Current Machines: IdeaCentre A300, ThinkPad Tablet, IdeaPad U410, and Yoga 3 Pro Touch
Deutsche Community Comunidad en Español
Lenovo - the latest in DOtabs, DOpads, DOcentre's, DOstations and DOservers!

Similar Messages

Reset CMOS, system will not boot

This is a long story but I will try to keep it short:
I just bought a new 875P Neo-FISR and a 3.0 GHz Prescott, which from reading the other posts could have been a mistake. I installed the CPU, memory, and the video card and pressed the power button and received a "CMOS Data Wrong" error. So I tried to correct the problem but when I saved and exited then the system would not boot back up. So, I reset the CMOS via the jumper and tried again. After MANY attempts I change just the month in the date setting. And what do you know...it would not boot back up. The D-Bracket LEDs were: 1-flashing red/green, 2-flashing red/green, 3-red, and 4-red
I must have read almost every post in this forum and tried many things such as:
disconnecting all componets except for video, ram, and cpu
the during boot to recover the BIOS
removing mobo from case, maybe a short
moving the memory to different slots
moving the PSU to a different computer...it works
disconnecting the PSU from the mobo and and removing the battery overnight. The first night I did not disconnecting the PSU from the mobo and I found that did nothing.
Tryed everything that I could think of and some stuff that others thought of but nothing worked. However the last item...removing the battery...did change things some. Now nothing happens, and I mean nothing...no lights, no fans, no buzzing...nothing.
Any ideas would be greatly appreciated. The only recourse I have left is to RMA the board.

I tried one stick in all of the slots with and without the sound card. That did not work either.
The voltage for my memory is 2.6 so that is what I tried. But if I can get it to boot up again I will try 2.7.
Tks.

Windows 8 and Canvio Desk 3TB: System will not boot when external hdd is connected

http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/HP-PAVILION-A6109N-amp-windows-8-System-w...
Hi,
just recently upgraded to Win Pro on my HP PAVILION A6109N. I also bought a toshiba canvio desk 3TB. What I notice is that if I reboot my pc with the extermnal HDD connected, my system will not boot.
I have check my BIOS boot settings and the order of the boot.
I have tried disabling USB Legacy Support in the BIOS
I have reformatted the external HDD
but still my desktop will not boot if the external HDD is connected....If I disconnect the external HDD...the system will boot up ....
I am at a loss....*** scratching my head ***

Update: The only solution for me was to format the drive as ext3 and plug it into one of my Asus RT-N66U USB ports, as most routers don’t yet recognize 3TB drives as NTFS. It’s not much help to people who don’t have a router with this capability, and it also slows transfer rates to ~12MB/s.
Given the short length of the cable, your only other options are to have the 3TB Canvio sitting right next to you so you can unplug from a front USB port before each boot, or place it towards the rear of your desk and crawl under the desk to disconnect it from your PC prior to each boot.
It's a pity because Toshiba produce great internal HDD's, but my experience when it comes to external drives is they're simply junk. I wish I had read the reviews before purchasing.

The system will not boot

Hello, I am trying to install windovws after the restart can not install Yosemite because can`t please format the hard disk.Please help because just yesterday bought macbooc

FYI...the top partition is too full. You need free space. You will need to remove the bottom partition then make the top partition larger. Make sure you have 10% or more free space. If you use Parallels or VMware you don't have to partition your drive. If you use the vm software you can run Windows wihtout having to reboot into bootcamp each time you want to use it.
See this link for help after you resize your top partition.
https://www.apple.com/support/bootcamp/
I forgot to ask...
If the system will not boot, how are you seeing Disk Utility. Are you booted from the Recovery Drive? If yes, then you will need to erase the internal drive and reinstall Yosemite on the internal. When you erase, make it one partition. You can add a second partition later that's smaller.
Note: you posted in the OS X 7 Lion instead of the Yosemite forum. In the future, asking on the correct forum gets the best answers.
Parallels http://www.parallels.com/
VMware Fusion http://www.vmware.com/products/fusion/

Operating reference system will not boot.

hi! bought the iphone 4s in Italy and it does not work. Operating reference system will not boot. Change of firmware and restore did not help. How can I change it while in Russia. Can I send in the mail store??

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

System will not boot - Arrives at 'Bluetooth Setup Assistant popup &

A Bluetooth Setup Assistant (BSA) pop-up arrived on my screen looking for bluetooth mouse (which I do not have). It is in front of the log-in screen (I can just see it behind the BSA pop-up). I cannot get rid of it. The keyboard and mouse will not work and i cannot reach any of the system tools as the system has not booted. I tried (a) shutting off & restarting. But it always arrives at this same screen. (b) safe mode start with same result. (c) Command Option PR start with same result. (d)Then put in installation disk to start from disk (Holding down 'C') with same result. Now my installation disk will not eject (holding down mouse button on startup). (e) Also tried startup with firmware (Command-Option-O-F) with same result.
Can anyone help get me round this original problem as well as finding a way of ejecting the installation disk?

Note: I assume in the following that your mouse & keyboard are standard USB wired devices -- if not, please say so. Also, if yours are not Apple branded devices, please mention that too.
It sounds like your keyboard & mouse are not being recognized as connected to your Mac so the OS is looking for Bluetooth devices as an alternate source of user input. If this is so, what may help is to unplug them & plug the keyboard into a USB port on your Mac (not on a USB hub attached to it) after restarting, when you see the BSA screen.
If this doesn't work, try unplugging all other USB devices & repeat the above. If that doesn't work, you may have a defective keyboard or mouse. Check for that by substitution.

System will not boot / black screen

:undecided:Problem: System does not boot. Black screen.
I just put this system together. I've returned the CPU and motherbd. for exchange, thinking one may be defective. Still No Boot. PowerSupply checks out good. MSI video card checks out good too. Could it be the memory stick? Pls. HELP. BTW - Yes, I did remember to plug in the 4-pin power connector.
Motherbd: MSI 865PE Neo2 (option2) (New)
CPU: INTEL P4 2.4G 1 MB L2 533MH (New)
http://www.newegg.com/app/viewproductdesc.asp?DEPA=0&description=19-116-141&ATT=Processors&CMP=OTC-B1zrat3
Memory: 1 dimm - 1GB PC2700 333MHz DDR SDRAM
http://www.ocsystem.com/1gbpc33ddrsd.html
VGA : MSI Video Card - Geforce FX5200-TD128 128MB TV-Out DVI-I (Tested Good)
http://www.ussa.com/ussaonline/product.asp?dept%5Fid=10610&pf%5Fid=100%2D106%2D1004159
PowerSupply : Enermax EG365P-VE-FC 350W (Tested Good)
HardDrive : 120GB WesternDigital

You got me there. I only looked at the LED's after it hangs.
I must wait for my reshippment of my memory. I returned it, and asked them to test it. If it tested good, then it probably not compatible with system. My next option was to order GIGARAM 1GB, since it is on the list of recommended DDR.
Sorry, I cannot reboot at the moment. Do you think it is the memory, or something else?
Thanks,

System will not boot up

MB: KT6 Delta-LSR
CPU: XP2500 Barton
GFX: Asus V9520 Magic/T 128mb
RAM: 1028 pc3200 ddr400 (2x512) Geil Branded
HDD: Maxtor 40GB 2mb Buffer
Put it all together formatted the HDD, installed windows, network was working perfectly. (on ASUS via600 board)
Next day turn it on and nothing, zilch not even a flashing cursor top left of screen, dont even boot to DOS. screen is completely blank.
Tested CPU, GFX, RAM and PSU in another base unit and they work fine, yet put them all together and nothing.
1st I thought it was the mainboard so I sent the ASUS board back and ordered the KT6 Delta nice looking board. But still exactly the same problem.
Lights on case are lit all fans are turning ect yet still the system will not boot up i dont even get a flashing cursor top right of my screen.
There is no light with this mainboard for some reason.
All components work when fitted to another mainboard in a different case.
NB: one thing I have noticed is that there are two power sockets on this board,
1. The usual 20 pin socket (which I am connected to)
2. A 4 pin socket near to the CPU (whilst my PSU has a plug that will fit this sockect also, I am unsure as to connect instead of/as well as or leave unplugged.

Like I have stated before, it is the compatibility issue related towards your chip fsb and your memory fsb. I know that not everyone has money to go buy another stick of memory, I don't. But maybe you could exchange from the place you bought and say that it was a mistake? The cheapest route without getting the fsb chip to match the fsb of the memory stick is to get PC2700 memory. Have you tried going for this yet? I'm sure that your motherboard may not be shot, my board didn't get shot after trying to the two different fsb. You have to understand, motherboards are picky when it comes to running the hardware. If there is a conflict, it won't run right, I could run at a lower fsb and get it to work fine, but it wasn't at it's full potential, and I wasn't going to waste my time trying to find the fsb that would work correctly. So, I just let my friend have the stick back. This is why I'm asking you to try a lower speed stick of memory, because I have experienced this. But so far you haven't even seemed to notice my replies, could you take a quick overview of what I have said? Sorry if I come off as rude, just I am taking the time to write these replies and really am trying to help from my knowledge base. I have experienced this type of problem of what you are talking about personally.
Ok, so maybe I might not know it all, seeing that other people replying here have the same mb spec and chip fsb and memory like your trying to run, they might know more when it comes to that area for sure, just I didn't have luck trying to run a faster stick of memory compared to my chip, even though my board could run it, I couldn't get it to work, at all. I would just get a black screen, I thought I shot my GPU. Then I reset CMOS and the bios would flash, then when it would start pulling from harddrive, boom, black screen again. I had my friend tinker with my volt. to the right volts of the memory stick, still couldn't get nothing. This is why I am a little skeptical about you being able to run it at all in the long run. Hopefully you can find a way, maybe it is your manufacturer of your stick, but my conclusion is, if it isn't going to work with one, or two of same speed, try lowering it. Like I said, I tried it on this setup right now, and I didn't have to replace the chip or mobo, or gpu, so those should be fine.

System will not boot with Seagate 3Tb expansion drive plugged in.

I have a HP Pavilion HPE h8- 1214 Desktop , I recieved a Seagate 3TB expasion drive as a gift but when plugged in, the system will not boot. It turns on but thats it. It never gets to the boot sequence. I have it plugged into the top 3.0 usb slot and have tried all of the other slots as well with no sucess. But if I leave it unplugged the system boots right up. I can then plug it in and it works fine. I have plugged it into my wifes HP All- In- One and it boots fine and works. I have a WD 2TB drive that works fine as well on my system . I have searched Segates support for hours and all they say is to change the boot sequence. Have tried that, no go. What they dont get is no matter what I do if that drive is plugged in it never gets as far as booting and reading the boot sequence. Please help. Thank you!

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

How do I get recover disc for vista when system will not boot???? For Pavilion pc a6157c

Pavilion pc a6157c How do I get recover disc for vista when system will not boot????

Read THIS HP Support Document concerning ordering recovery discs for your HP a6157c. Go to THIS HP webpage to order the "Vista Home Premium 32bit 73NAv3PrA1 + Supp 4 Recovery Kit" for your computer. If you are not looking to order the recovery discs or have some other issue with your computer, please provide detailed information concerning the problem.
Frank
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

System does not boot during Hyper V installation

Hi -
I was trying to install Hyper V on my Windows 8.1 professional edition, 64 bit OS. The installation was through ISO downloaded through MSDN. During installation I had to hard boot my system through switch off. Now my system does not boot correctly and during
boot it flashes a message "The last windows installation did not complete please install the setup". Does this mean that my existing 8.1 OS has crashed ? how can i come out of this and recover my data ?
My hardware configuration is :
i7 processor, 16GB RAM, intel graphics Card, windows 8.1 professional 64 bit OS.

Hi RahuIM,
You can try to enter safe mode then copy your personal data to the data volume then reinstall the system.
The related KB:
Start your computer in safe mode
http://windows.microsoft.com/en-us/windows/start-computer-safe-mode#start-computer-safe-mode=windows-7
Step-By-Step: Enabling Hyper-V for use on Windows 8.1
http://blogs.technet.com/b/canitpro/archive/2014/03/11/step-by-step-enabling-hyper-v-for-use-on-windows-8-1.aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

System does not boot when PCIe express Card is inserted in system. Using Spartan-6 PCIe Integrated Endpoint Block 1.3

Hi,
I am using Spartan-6 PCIe Endpoint Block core v1.3 and I am using ISE 12.1. I have used the PIO example design,
modified it according to our design.
The core is configured as below:
BAR0 - 8KB, 32-bit, Memory Type
Lanes - x1
Clock - 125 MHz (system clock)
The card is a custom board. When the card is pluged into the system the system does not boots, it hangs.
I have tried debugging using chipscope and monitored trn_lnk_up_n, trn_reset_n and trn_clk. trn_lnk_up_n stays
high (deasserted), trn_reset_n stays low (asserted), trn_clk is low (No clk).
What might be the issue?
Thanks & Regards.

Thanks Gabor, for the response.
I refered couple of answer records like AR# 34873 and AR# 34894, I monitored trn_reset_n, sys_reset_n, clock_locked, PLLLKDET and RESETDONE signals as suggested in AR# 34894.
Status as follows:
SYS_RESET_N = 1 (deasserted)
TRN_RESET_N = 0 (asserted)
CLOCK_LOCKED = 0 (deasserted)
PLLLKDET = 0 (deasserted)
RESETDONE = 0 (deasserted)
which means the transceiver PLL frequency is not within the predetermined tolerance. Is this problem related to the PCIe Jitter Attenuator I am using on the board to derive 125MHz from 100MHz system Clock.
Thanks & Regards

Unsupported chassis type 52, system can not boot

I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots.
I am not aware if this spare had been used in production before.
Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.
Thanks,
Tom
The following is displayed on Console:
Exiting to ios...
Rommon reg: 0x0E000380
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(37)SG1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 30-Jul-07 13:47 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x11863D38
Unsupported chassis type 52, system can not boot
Rebooting in 10 seconds...
10 09 08 07 06 05 04 03 02 01
* Welcome to Rom Monitor for WS-X4516-10GE System.       *
* Copyright (c) 2003-2006 by Cisco Systems, Inc.         *
* All rights reserved.                                   *
Rom Monitor Program Version 12.2(31r)SGA
Supervisor: WS-X4516-10GE Chassis: WS-C4507R-E
Hardware Revisions - Board: 4.11 CPLD Tie: 32 FPGA Pod: 14
MAC Address : 00-11-21-ac-cf-b0
Ip Address   : Not set.
Netmask      : Not set.
Gateway      : Not set.
TftpServer   : Not set.

tffmaguire wrote:I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.Thanks,Tom
You don't have the right IOS version to meet the minimum requirements for this chassis.
See the following document
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet0900aecd801792b1.html
Table 5 lists 12.2(40)SG as the minimum IOS required for a 4507R-E chassis and 12.2(54)SG as the minimum IOS for a 4507R+E chassis. You only have 12.2(37)SG1 on your engine, hence the lack of boot.
Upgrade the IOS via ROMMON (slow and painful, but it'll work) and re-try.
Cheers.

After installation of 10.6.5 system does not boot

After I updated my system with the latest release 10.6.5, the system does not boot up at all. It shuts down every time it restarts. All I can do is go into single user mode and then I cannot repair the disk as I always get the error that "The volume Macintosh HD cannot be repaired when it is in use"
Any other suggestions?

It sounds like your friend's DVD is hardware specific to his Mac and will not work in your Mac.
Since you say a safe boot work that generally indicates that the problem is with third party software because the safe boot prevent any of that from starting.
Allan

V210 alom starts up; status is alright but system does not boot

I have a series of v210s, all running solaris 9.
After a power down on of the systems powers on alright. showenvironemnt
shows
r4n8mgt> showenvironment
=============== Environmental Status ===============
System Temperatures (Temperatures in Celsius):
Sensor Status Temp LowHard LowSoft LowWarn HighWarn HighSoft HighHard
MB.P0.T_CORE OK 51 -- -- -- 110 115 118
MB.P1.T_CORE OK 60 -- -- -- 110 115 118
MB.T_ENC OK 15 -6 -3 5 40 48 51
Front Status Panel:
Keyswitch position: NORMAL
System Indicator Status:
MB.LOCATE MB.SERVICE MB.ACT
OFF OFF OFF
System Disks:
Disk Status Service OK2RM
HDD0 OK OFF OFF
HDD1 OK OFF OFF
Fans (Speeds Revolution Per Minute):
Sensor Status Speed Warn Low
F0.RS OK 7336 -- 1000
F1.RS OK 7180 -- 1000
F2.RS OK 7180 -- 1000
F3.RS OK 7336 -- 1000
MB.P0.F0.RS OK 17307 2000 2000
MB.P0.F1.RS OK 17763 2000 2000
MB.P1.F0.RS OK 17307 2000 2000
MB.P1.F1.RS OK 17307 2000 2000
Voltage sensors (in Volts):
Sensor Status Voltage LowSoft LowWarn HighWarn HighSoft
MB.P0.V_CORE OK 1.44 -- 1.26 1.54 --
MB.P1.V_CORE OK 1.50 -- 1.26 1.54 --
MB.V_VTT OK 1.28 -- 1.17 1.43 --
MB.V_GBE_+2V5 OK 2.50 -- 2.25 2.75 --
MB.V_GBE_CORE OK 1.20 -- 1.08 1.32 --
MB.V_VCCTM OK 2.55 -- 2.25 2.75 --
MB.V_+2V5 OK 2.58 -- 2.34 2.86 --
MB.V_+1V5 OK 1.51 -- 1.35 1.65 --
MB.BAT.V_BAT OK 2.90 -- 2.70 -- --
Power Supply Indicators:
Supply Active Service OK-to-Remove
PS0 ON OFF OFF
Power Supplies:
Supply Status Underspeed Overtemp Overvolt Undervolt Overcurrent
PS0 OK OFF OFF OFF OFF OFF
Current sensors:
Sensor Status
MB.FF_SCSI OK
r4n8mgt>
However the system does not boot, or show any diiagnositics.
I connected a serial to the "serial management port" but all i get is
C Alert: SC System booted.
SC Alert: Host System has Reset
[SC Status 7fff - OK] Enter #. to return to ALOM.
Copyright 2004 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Sun(tm) Advanced Lights Out Manager 1.5.2 (m1104)
Please login: admin
Please Enter password: ********
r4n8mgt> console -f
Enter #. to return to ALOM.
Here it sits and does nothing.
Any idea?
Lydia

That sounds like a failed logic board or display module on the logic board...either way you need to take it to an Apple store genius bar and have the techs test it to see exactly what has failed. The testing is free so give the techs a chance at diagnosing the problem.

My System do not boot

Similar Messages

Maybe you are looking for