My system doesn't turn ON.

Hello, my system can't turn on, when I press the button the laptop puts all the lights on for less than a second and then it only shows two light indicators, the POWER light and the AC adapter (or battery). I've tried every thing I've removed everything connected without battery directly to the AC POWER, but it's having the problem no matter what I do.
My machine is a thinkpad X200 model: 7454-2HU  S/N: LV-0***7 (under guaranty). The main problem I have is that my system is on guaranty but I live in SPAIN and I've contacted with them and they say that they cannot use the IWS guaranty because they are not supliers. So what should i do? they said that it's maybe a motherboard failure, and replace one is like 1000 Euro they said.
 The system is on guaranty on US but I tried to contact them by phone but they doesn't answer. Could I just ship my laptop to EEUU or another suplier with IWS of my laptop, and repair this issue?...I would pay the shipment.
Please, what should I do?.... Thank you, Regards
PD: I've tried connecting to another monitor by VGA also and it's not working. 
Message Edited by kaonquark on 08-10-2009 12:38 PM
Message Edited by kaonquark on 08-10-2009 12:43 PM
Message Edited by kaonquark on 08-10-2009 12:48 PM

take the ram module out and put it back in again. 
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

  • I turned off my ipad when it was upgrading the system and now it doesn't turn on. What should I need to do now?

    Hello!!!
    Can somebody help me?
    I just turned off my ipad but I forgot that it was upgrading a new system...and now it doesn't turn on.
    What should I have to do?
    Thanks

    Hold down on the sleep button and the home button at the same time for about 10 seconds until the Apple logo appears on the screen. Ignore the red slider. When the logo appears let go of the buttons.

  • MacBook doesn't turns into sleep mode and swop doesn't work.

    MacBook doesn't turns into sleep mode and swop doesn't work.
    Can you help me please. I have a MacBook Pro 8.2. I reinstalled OS X to make swop file working, but it still doesn't work. I reinstalled OS X from Internet recovery.
    Start time: 10:31:02 03/15/15
    Model Identifier: MacBookPro8,2
    System Version: OS X 10.10.2 (14C109)
    Kernel Version: Darwin 14.1.0
    Time since boot: 3 minutes
    Memory
        BANK 0/DIMM0:
          Size: 4 GB
          Speed: 1333 MHz
          Status: OK
          Manufacturer: 0x029E
        BANK 1/DIMM0:
          Size: 4 GB
          Speed: 1333 MHz
          Status: OK
          Manufacturer: 0x029E
    SerialATA
       TOSHIBA MK5065GSXF                     
    Diagnostic reports
       2015-03-15 Boom 2 crash
       2015-03-15 com.apple.internetaccounts crash
    Log
       Mar 15 10:26:10 memorystatus_thread: idle exiting pid 546 [tccd]
       Mar 15 10:26:11 memorystatus_thread: idle exiting pid 547 [nsurlstoraged]
       Mar 15 10:26:12 memorystatus_thread: idle exiting pid 544 [soagent]
       Mar 15 10:26:13 memorystatus_thread: idle exiting pid 548 [nsurlstoraged]
       Mar 15 10:26:43 memorystatus_thread: idle exiting pid 556 [com.apple.CodeSi]
       Mar 15 10:26:44 memorystatus_thread: idle exiting pid 558 [accountsd]
       Mar 15 10:26:45 memorystatus_thread: idle exiting pid 553 [com.apple.iCloud]
       Mar 15 10:26:46 memorystatus_thread: idle exiting pid 561 [networkd_privile]
       Mar 15 10:26:47 memorystatus_thread: idle exiting pid 555 [secinitd]
       Mar 15 10:26:48 memorystatus_thread: idle exiting pid 560 [tccd]
       Mar 15 10:26:49 memorystatus_thread: idle exiting pid 562 [secd]
       Mar 15 10:26:50 memorystatus_thread: idle exiting pid 554 [com.apple.intern]
       Mar 15 10:26:51 memorystatus_thread: idle exiting pid 565 [nsurlstoraged]
       Mar 15 10:26:52 memorystatus_thread: idle exiting pid 563 [soagent]
       Mar 15 10:26:53 memorystatus_thread: idle exiting pid 551 [syncdefaultsd]
       Mar 15 10:26:54 memorystatus_thread: idle exiting pid 557 [CoreServicesUIAg]
       Mar 15 10:26:55 memorystatus_thread: idle exiting pid 567 [iconservicesd]
       Mar 15 10:26:56 memorystatus_thread: idle exiting pid 566 [iconservicesagen]
       Mar 15 10:26:57 memorystatus_thread: idle exiting pid 568 [systemstatsd]
       Mar 15 10:26:58 memorystatus_thread: idle exiting pid 550 [cfprefsd]
       Mar 15 10:26:59 memorystatus_thread: idle exiting pid 552 [cfprefsd]
       Mar 15 10:27:00 memorystatus_thread: idle exiting pid 549 [coreduetd]
       Mar 15 10:27:01 memorystatus_thread: idle exiting pid 564 [nsurlstoraged]
       Mar 15 10:28:18 ** GPU Hardware VM is disabled (multispace: disabled, page table updates with DMA: disabled)
       Mar 15 10:29:09 proc 316: load code signature error 4 for file "Boom 2"
    I/O per process: coresymbolicati (UID 0) is using 15 MB/s
    kexts
       com.globaldelight.driver.Boom2Device (1.1)
    Daemons
       com.apple.installer.osmessagetracing
    Agents
       com.apple.AirPortBaseStationAgent
       com.globaldelight.Boom2Daemon
    Extensions
       /Library/Extensions/Boom2Device.kext
       - com.globaldelight.driver.Boom2Device
       /System/Library/Extensions/EPSONUSBPrintClass.kext
       - com.epson.print.kext.USBPrintClass
       /System/Library/Extensions/JMicronATA.kext
       - com.jmicron.JMicronATA
    Applications
       /Applications/Boom 2.app
       - com.globaldelight.Boom2
       /Applications/Boom 2.app/Contents/Library/LoginItems/Boom2Daemon.app
       - null
    Bundles
       /Library/Printers/Canon/BJPrinter/Plugins/BJNP/CIJNetworkIOM.plugin
       - jp.co.Canon.ij.print.iom.CIJNP
       /Library/Printers/Canon/BJPrinter/Plugins/BJNP/CIJNetworkPBM.plugin
       - jp.co.Canon.ij.print.pbm.CIJNP
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/BJUSBIOM.plugin
       - jp.co.canon.bj.print.bjusbiom
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/BJUSBPBM.plugin
       - jp.co.canon.bj.print.pbm.USB
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/CIJUSBClassDriver.plugin
       - jp.co.canon.ij.print.CIJUSBClassDriver
       /Library/Printers/Canon/BJPrinter/Plugins/BJUSB/CIJUSBClassDriver2.plugin
       - jp.co.canon.ij.print.CIJUSBClassDriver2
       /Library/Printers/Canon/BJPrinter/Plugins/IJBluetooth/IJBluetoothIOM.plugin
       - jp.co.canon.ij.print.ijbluetoothiom
       /Library/Printers/EPSON/CIOSupport/CIOHelper.plugin
       - com.epson.print.plugin.CIOHelper
       /Library/Printers/EPSON/CIOSupport/EPSONUSBPrintClass.plugin
       - com.epson.print.plugin.USBPrintClass
       /Library/Printers/EPSON/CIOSupport/XIOP.plugin
       - com.epson.print.plugin.XIOP
       /Library/Printers/EPSON/CIOSupport/XIORemoteClient.plugin
       - com.epson.print.plugin.XIORemoteClient
       /Library/Printers/EPSON/CIOSupport/XIORemoteServer.plugin
       - com.epson.print.plugin.XIORemoteServer
    Restricted files: 219
    Elapsed time (s): 238

    Remove "Boom" and test.
    Any third-party software that doesn't install by drag-and-drop into the Applications folder, and uninstall by drag-and-drop to the Trash, is a system modification.
    Whenever you remove system modifications, they must be removed completely, and the only way to do that is to use the uninstallation tool, if any, provided by the developers, or to follow their instructions. If the software has been incompletely removed, you may have to re-download or even reinstall it in order to finish the job.
    I never install system modifications myself, and except as stated in this comment, I don't know how to uninstall them. You'll have to do your own research to find that information.
    Here are some general guidelines to get you started. Suppose you want to remove something called “BrickMyMac” (a hypothetical example.) First, consult the product's Help menu, if there is one, for instructions. Finding none there, look on the developer's website, say www.brickmymac.com. (That may not be the actual name of the site; if necessary, search the Web for the product name.) If you don’t find anything on the website or in your search, contact the developer. While you're waiting for a response, download BrickMyMac.dmg and open it. There may be an application in there such as “Uninstall BrickMyMac.” If not, open “BrickMyMac.pkg” and look for an Uninstall button. The uninstaller might also be accessed by clicking the Customize button, if there is one.
    Back up all data before making any changes.
    You will generally have to restart the computer in order to complete an uninstallation. Until you do that, there may be no effect, or unpredictable effects.
    If you can’t remove software in any other way, you’ll have to erase and install OS X. Never install any third-party software unless you're sure you know how to uninstall it; otherwise you may create problems that are very hard to solve.
    Trying to remove complex system modifications by hunting for files by name often will not work and may make the problem worse. The same goes for "utilities" such as "AppCleaner" and the like that purport to remove software.

  • TS2570 my mac doesn't turn on??? even it is charged

    my mac pro 13 doesn't turn on ??
    when i press the power button it just on the led light but laptop doesn't turn on. though the charger is connected..

    Hello, not too much you can try, might be the charger gone out?
    Intel-based Macs: Resetting the System Management Controller (SMC)...
    http://support.apple.com/kb/HT3964

  • T430s Doesn't Turn on - Lights Flash Once

    Hi,
    I'm trying to fix a friend's T430s and the issue is that it doesn't turn on. With the battery plugged in, nothing happens. No lights and no sounds. When I plug the adapter in the buttons along the top of the keyboard (volume mute,power, etc.) and then they turn off and nothing. The motherboard was replaced, but the issue remains. 
    Any tips or trick are much appreciated
    Thanks

    Hi Cimanim,
    Welcome to Lenovo Community!
    As per the query we understood that you are facing issue with No POST on your ThinkPad T430s.
    Have you checked with performing power drain by removing the power adapter and battery from the system, hold the power button for 15 to 20 seconds do this process for 2 to 3 times and connect only power adapter and check.
    If you find the issue still persists, then I suggest you to contacts Lenovo technical support if the system is under warranty or approach any nearby service center.
    Please click here to contact Lenovo customer support for your region to get the detail of service centers.
    Hope this helps.
    Best regards,
    Hemanth Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • X1carbon doesn t turn on

    My x1carbin thinkpad doesn t turn on. Have made a hard reset but still nothing. Please help!

    Hi Danizao,
    Welcome to Lenovo Community!
    As per the query we understood that you are facing issue with your ThinkPad X1 carbon not switching ON.
    Is there any LED indication on your system when you switch on the system?
    Have you checked with different power socket/Power adapter?
    Is the hard reset which you have performed is that reset hole, am I right?
    If the reset is done from reset hole and issue still persists then you have to replace the system board.
    Suggest you to visit nearby service center for further assistance, as this could be a hardware issue.
    Hope this helps.
    Best regards,
    Hemanth Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • I5 27" imac display doesn't turn on

    Hi,
    This issue just cropped up for me this morning. When I go to turn on my recently purchased (Feb 2011) core i5 27" iMac, the screen doesn't turn on. Instead, it remains black until I hit the power button again, after which it will usually come to life. It sometimes goes black again without any warning. I can usually get the screen to come back to life if I hit the power button. However, I have an older 24" cinema display hooked up as a second monitor, and it always comes to life when I start up, and never goes black like the iMac display. Anyone else having this problem? Are there any known/recommended solutions?
    Thanks!

    Reset the SMC > Intel-based Macs: Resetting the System Management Controller (SMC)
    and zap the PRAM > Resetting your Mac's PRAM and NVRAM
    Then if that doesn't help, contact Apple Support or your Local Apple Service Provider. > Apple - Support - iMac - Service FAQ
    Dennis

  • IMac display doesn't turn back on after sleep

    This is a new problem on my two-year old iMac, and didn't happen before. What is happening with my iMac is that when it goes to sleep and the display turns off, the display doesn't turn back on when I move the mouse, press the keys or the power button.
    It happens only after around 12 hours or so of inactivity, it seems. I have to reboot the iMac to force the display to turn back on. I think it is display issue, not the computer lockup because I checked which logs were written in /var/log - system.log was being written until I rebooted the iMac. However, I didn't see any information in there around the same time that I tried to turn the iMac back on.
    Any ideas on how to debug the issue.

    Hi dailyjoe
    1. Reset your SMC exactly as instructed in the following article:
    http://support.apple.com/kb/HT1543
    2. It would be normal for you to have to startup your iMac if it lost power while in sleep mode, look at the box "Start up automatically after a power failure" in the Energy Saver preference.
    I have always left the box for "Start up automatically after a power failure" unchecked and do occasionally find the iMac is shutdown because the power has gone off. I would suggest leaving the box unchecked, it's better than having the iMac going off & restarting multiple times if you are having bad weather or power issues.
    Dennis

  • My Zen Neeon 5gb doesn't turn on correctly, only appears CREATIVE on the scr

    I need help because my Zen Neeon 5GB doesn`t turn on the right way. I was listening to music the one day before?and when I tried to turn it on it only appears on the screen: CREATIVE and the menu doesn`t appear on the screen and I can`t listen to music and it doesn`t turn off until I reset it. But you can listen to the hard disk running. I can use it like an USB device but I can`t listen to music. i tried with the upgrade from firmware but appears:
    Device detection failed! Please power off it to generate system file.
    Device upgrade failed!What happen is`t death?

    Have you tried anything in the recovery mode on the player. If not i would go to creative knowledge base and lookup "recoverymode." I would try the clean-up and format first.

  • My old phone doesn't turn and I want to get the serial number for it to see if it's eligible for the battery replacement with Apple. Can I use the IMEI number to find the serial number?

    My old phone doesn't turn and I want to get the serial number for it to see if it's eligible for the battery replacement with Apple. Can I use the IMEI number to find the serial number?

    Call applecare.  They can look up the IMEI number in their system to see if the device is eligible.
    AppleCare US phone number: (800)-694-7466
    Contact Apple for support and service
    http://support.apple.com/kb/HE57

  • T61 doesn't turn on after BIOS upgrade! PLEASE HELP!

    Hi all,
    I just reinstalled XP on my 4 months old T61 and installed Lenovo's System Update thing. There was an BIOS update option there, so I selected it. It downloaded it and then done the upgrade - there were no errors, everything was smooth. All was fine. At least it looked that way. I rebooted it. It hanged on the boot screen (at POST). So I tried to reboot it or turn it off - there was no way to do it - the keyboard was not responding, tried pressing the power button for like a minute, but nothing. It was frozen on the bootscreen logo. So I removed the power plug and then the battery to cut the power and turn it off.
    I inserted the battery and the power plug back... and... IT DOESN'T TURN ON ANYMORE. Not only it will not respond to me clicking the power button, but also the light on the backside of the lid doesn't light up when I plug in the power supply. What the hell happened? What should I do?
    I tried removing the RAM and replacing it, cause I had a spare stick, but, as I thought it didn't do anything.
    Is it possible that the power circuit inside T61 was somehow damaged when I removed the battery when the computer was running?
    Some more info:
    The battery was fully charged when flashing, I was on the AC and the BIOS version was selected automatically via Lenovo System Update.
    I know how to flash BIOSes, I did it like a hundred times in my life already, even hex-hacked one on a very old PC. Never had any problems.
    This is the BIOS I upgraded to:
    http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-67988
    My T61's model is: 6465-CTO
    OMG I'm so desperate right now.
    Please HELP! I don't know what should I do!
    And to top it off, I don't know if my warranty is going to be any good in Poland (see thread: http://forum.lenovo.com/lnv/board/message?board.id=Special_Interest_General&thread.id=88 )
    Best regards,
    NIXin

    It is disturbing - Yes.
    However, I have lost count of the number of BIOS or ECC updates I have made with System Update and have never ever had something go wrong. Obviously those that experience a problem are going to look for help and post in forums, it would be interesting to know how many have never had a problem?? They have no reason to post.
    You wrote; "bricks their Txx about once a week", how many ThinkPads are sold per week? It is guaranteed to be an absolute nightmare for the owner, quite understandably, but if I was paranoid I wouldn't drive my car to work - I might have an accident.
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • Satellite L655 doesn't turn on - Indicators only blink

    Everything disconnected from the laptop. Drive of DVD, HDD, CardReader, battery, Wi-Fi. Only the processor and memory (it is tested on other laptop) are connected. I connect the power unit. The indicator of connection of the power unit (the first at the left, color white) turns on.
    We press the inclusion button, the laptop doesn't turn on. Only the indicator of connection of the power unit (the first at the left) is switched on and two indicators - the second at the left and the second on the right blink 1 time white color.
    It most likely codes of errors. How them to understand?

    Hi
    The second from left is Power indicator.
    Normally this indicator glows white when the computer is turned on. However if you turn the computer off into sleep mode, this indicator flashes amber: one sec on two sec off.
    Both while the system is shutting down and while it remains turned off.
    The 3rd from left, battery indicator show the condition of the battery charge: white indicates the battery is fully charged, amber indicates the battery is charging and flashing amber indicates low battery condition.
    The second from right seems to be an SD card (bridge media slot) indicator and this glows white when the computer is accessing the sd card.
    For me it sounds like the motherboard is affected and this means you need an help from technicians

  • Keyboard backlight doesn't turn on auto in dark

    hi i bought macbook pro retina 13(osx mavericks) few days back i observed that my keyboard backlight doesn't turn on auto in dark i have to manually turn it on every time so i want to know whether apple has removed this auto turn on in new mavericks or is i m having a issue with my keyboard

    Auto keyboard backlight still exists: System Preferences -> Keyboard -> "Adjust keyboard brightness in low light". Is that option selected? If so, deselect and select it again. If that doesn't work: Intel-based Macs: Resetting the System Management Controller (SMC)

  • Phone doesn't turn on, solid red light, requires send back BUT I have a request.

    I've essentially figured out that my Z10 needs to be returned for some sort of warranty / repair, however I'm really hoping that we can request that the data on the phone be saved rather than it just be lost forever. Is this possible? There are many important notes that haven't been backed up.
    Symptoms: Phone doesn't turn on, red light comes on solid for a few minutes and then turns off. Connecting it to a computer doesn't result in anything (no computer connection, no change in phone).
    I am with Bell, and I even live in Kitchener (I could personally drop into BB to sort this out) I wanted to check here as a last resort before sending it back.
    Thanks!

    Hi and Welcome to the Community!
    I used these steps from Geek Squad and it worked for me.
    Restore BB10
    When a BlackBerry 10 device is only flashing the red light and refusing to boot up, this indicates that the device’s operating system has become corrupted. The flashing light may follow the pattern of 1, 2 or 3 short blips, with a longer pause between the sets.
    In order to fix this, you need to re-install the operating system on the device, which will then set the device back to its original factory state.
    Please note: this process will completely wipe your device, so please make sure you have a backup of your personal information available to restore before going through this process. 
    Download and install the latest version of BlackBerry Link for your computer.
    Open BlackBerry Link software.
    Plug in the BlackBerry device using your USB cable.
    At the bottom left of the program, find the device you're having issues with and select it by clicking on it.
    The BlackBerry Link application will then ask to either reconnect or reload the device software. Choose Reload.
    Confirm the reload when prompted to do so, which will wipe clean any data previously on the handset.
    Allow the reload to complete, which can take some time. Whilst this is underway, the device will have a solid green light. This process of downloading and reinstalling the device can take an hour or more, depending on the speed of your internet connection, soplease don't disconnect the BlackBerry until the process has finished.
    Once the restore is complete, simply set up your device again, or restore it from a previous backup stored on your machine. However, if you want to restore a previous backup, remember to sign in to your BlackBerry ID on the device first! If you're not sure how to do this, we have a full guide available.
    The good news is, this process is almost identical on both PC and Apple Mac. Simply follow the same process as above. Finally, if you have any questions, please don't hesitate to get in touch with us.
    VIA | nakumba
    http://supportforums.blackberry.com/t5/BlackBerry-Z10/Z10-dead-red-light-blinks/m-p/2478589/highligh...
    Please thank those who help you by clicking the button.
    If your issue has been solved, please resolve it by marking "Accept as Solution"

  • SAP system doesn't automatically start after restart (but manual start ok)

    Hi,
    We've got a new production line of SAP EP 7.0 systems, which have CI on HP-UX and DIs on windows. The version is NW2004s SPS09.
    What we see is that after a restart of the windows servers (usually because of windows patching), the SAP system doesn't automatically start up. It doesn't start up if I restart the SAP<SID>_<instance> service either. 
    However, I've got no problem starting the system with the MMC.
    Any idea what I am missing here? is it as simple as a profile parameter ?
    As far as I can see the profile used seem ok.
    After a restart of the windows server the following files have log entries in the c:\usr\sap\<SID>\J<instance>\work folder
    sapstartsrv.log
    trc file: "sapstartsrv.log", trc level: 0, release: "700"
    Fri Nov 17 15:51:26 2006
    <<- ERROR: SapSSLInit(read_profile=1)==SSSLERR_LIB_NOT_FOUND
    sapstart.log
    Starting WebService thread
    SapSSLInit failed => https support disabled
    Webservice named pipe thread started, listening on port
    .\pipe\sapcontrol_97
    Webservice thread started, listening on port 59713
    sapstart.trc
    Starting WebService thread
    SapSSLInit failed => https support disabled
    Webservice named pipe thread started, listening on port
    .\pipe\sapcontrol_97
    Webservice thread started, listening on port 59713
    The windows event log have the application events
    (first)SAP Service SAP<SID>_<instance> successfully started.
    (at the same time)
    Failed to update service environment from user (STATOIL-NET\<sid>adm) environment. [ntservmgr.cpp 201]
    (note that this doesn't happen for all systems which have this problem, for other there is no entry like this)
    I see no failed login attemps in the security event log, but see the that a login is performed for SAPService<SID>.
    Since it also fails to automatically startup when I restart the service, I am able to use filemon to see what happens at a file level. Here I see that it can access the shared file system without any problems, and can read the profile and everything.
    MOM is running on the server and gets some Access denied errors since it doesn't have access to the shared file system, but I don't think that matters.
    Cheers
    Dagfinn

    hi  we are using sap bw 3.5 . database is oracle 9i
    i applied a kernel patch and when i tried to start the services . there was no problem with the oracle services  and saposcol but the service sap<sid>_nr did not start .
    when i went to check the error in work folder ..
    it say " SapSSLinit failed => https support disabled  .
    then i tried to start sap from cmd pmt . din`t work .
    is there a way to statrt this ...
    thanks alot.
    arjun

Maybe you are looking for