My system sometime can't boot

My computer can not restart. I have the system as below:
1) AMD Athlon XP 15000+ (NOT over clock) default CPU Volt: 1.71V
2) 512 MB PC133 Kingston Value Ram (Double side with 8 chips per side)
3) 300 watt Enlight Power Supply
4) 40 GB 5400 Rpm Maxtor HDD
5) 40*12*48 Aopen CD-RW Drive
6) OS – Windows XP Professional + Service Pack 1
7) VIA Service Pack 4.43
I upgrade my system with change of main board to MSI K7T Turbo2 (Bios version- 3.5 & date- 07/01/02)
and MSI MS-8852 Geforce 2 MX400 Card (64MB).
Before the upgrade ,the system runs perfectly ,after the upgrade and installation of programs ,the system sometimes can not rebooted using “ restart ” command through windows program. However it can booted using reset button. Unplug the reset button ,also same .
I would be much obligrd of you give me some suggestion to solve this problem.
Thanks!!!!!!!!!!!!!!!!!!!!!!

Hi,
When you replace a motherboard it's recommended you install Windows again from scratch.
Have you done this?

Similar Messages

Kernel panic after system update - can't boot :(

Hi
I've applied some pending updates to the system while restarting my MBP (I'm not sure, but it probably has contained the update from 10.6.3 to 10.6.4) but now it won't boot - I get a kernel panic.
When I boot instead using an external USB drive with a 10.6.3 installation on it, I get the message about the panic (below).
Any ideas how to solve this would be VERY MUCH appreciated.
Thanks!
Fri Aug 13 03:23:05 2010
panic(cpu 1 caller 0x4f9be4): "IOBluetoothHCIController::_RESERVEDIOBluetoothHCIController59 called."@/SourceCache/xnu/xnu-1504.3.12/libkern/c++/OSMetaClass.cpp:906
Backtrace (CPU 1), Frame : Return Address (4 potential args on stack)
0x82cd3a98 : 0x21b449 (0x5ce420 0x82cd3acc 0x2238a5 0x0)
0x82cd3ae8 : 0x4f9be4 (0x5cef90 0x814b0de8 0x814b0de8 0x3b)
0x82cd3b08 : 0x81486ba4 (0x814bc114 0x3b 0xcad3540 0x0)
0x82cd3b28 : 0x82f21d7f (0xc1c1e00 0xc9ff194 0x2 0x82ec3c03)
0x82cd3b78 : 0x82f22b6a (0xc9ff100 0x0 0x0 0xc9d6f00)
0x82cd3dc8 : 0x82ec31dc (0xc9ff100 0xc9fc300 0x82cd3df8 0x4faec3)
0x82cd3df8 : 0x82f20dc0 (0xc9ff100 0xc9fc300 0x82cd3e28 0xcacc780)
0x82cd3e18 : 0x5382aa (0xc9ff100 0xc9fc300 0x1 0x4fb2b4)
0x82cd3e78 : 0x5364df (0xc9fc300 0xc9ff100 0xcaccb80 0xca660e0)
0x82cd3f28 : 0x536a70 (0xc9fc300 0xcac9900 0x0 0x50aea4)
0x82cd3f78 : 0x53871f (0xc9fc300 0x8 0x82cd3fac 0x1)
0x82cd3fc8 : 0x29e6cc (0xcb41210 0x0 0x29e6db 0xc62f000)
Kernel Extensions in backtrace (with dependencies):
com.apple.driver.IOBluetoothSCOAudioDriver(2.3.7f1)@0x82f1f000->0x82f25fff
dependency: com.apple.iokit.IOAudioFamily(1.7.6fc2)@0x82ebf000
dependency: com.apple.iokit.IOBluetoothFamily(2.3.1f4)@0x81480000
com.apple.iokit.IOAudioFamily(1.7.6fc2)@0x82ebf000->0x82ed6fff
dependency: com.apple.kext.OSvKernDSPLib(1.3)@0x8147c000
com.apple.iokit.IOBluetoothFamily(2.3.1f4)@0x81480000->0x814bcfff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
10F569
Kernel version:
Darwin Kernel Version 10.3.0: Fri Feb 26 11:58:09 PST 2010; root:xnu-1504.3.12~1/RELEASE_I386
System model name: MacBookPro5,1

Kappy, I have various bluetooth devices (headset, wireless wacom tablet, etc) that I use from time to time, but the kernel panic happens very early in the boot process.
When I tried booting in safe mode (holding shift), I got the panic much sooner, but of a different type now:
Fri Aug 13 04:35:52 2010
panic(cpu 1 caller 0x474607): "Process 1 exec of /sbin/launchd failed, errno 2\n"@/SourceCache/xnu/xnu-1504.3.12/bsd/kern/kern_exec.c:3146
Backtrace (CPU 1), Frame : Return Address (4 potential args on stack)
0x7ab83e48 : 0x21b449 (0x5ce420 0x7ab83e7c 0x2238a5 0x0)
0x7ab83e98 : 0x474607 (0x5c06ac 0x831b68 0x2 0x0)
0x7ab83ef8 : 0x45e836 (0x5a22d20 0x1fe 0x575ca80 0x80000001)
0x7ab83f38 : 0x484da2 (0x57fdb7c 0x73aa5000 0x7ab83f88 0x7ab83f94)
0x7ab83f68 : 0x219044 (0x57fdb7c 0xffffff7f 0x0 0x575eb7c)
0x7ab83fa8 : 0x2a7a07 (0xffffffff 0x1 0x22f250 0x575eb7c)
0x7ab83fc8 : 0x29e8a6 (0x0 0x0 0x29e6db 0x524c0e0)
BSD process name corresponding to current thread: init
Mac OS version:
Not yet set
Kernel version:
Darwin Kernel Version 10.3.0: Fri Feb 26 11:58:09 PST 2010; root:xnu-1504.3.12~1/RELEASE_I386
System model name: MacBookPro5,1

Re: Satellite L310 - Can't boot from HDD

Hi
My L310 just died on me yesterday. My system just can't boot, not even in Safe Mode. And it keeps trying to boot via my network card, not through hard disk.
I have set it to the default BIOS settings but it doesn't help.
And it has this continuous loud beeping tone when it tries to boot via the network card. Beeping continues, even at the BIOS screen and during safe mode.
I have manually selected the hard drive but it keeps trying to boot through the network card.
And the laptop does not respond to the keyboard. Even with an external usb keyboard. When I sometimes manage to boot my system on the rare occasion, I arrive at the log in screen and can't key in my password.
Does anybody have similar problems?
Let me know. Thanks!

It looks like that your HDD is faulty. Does the BIOS recognize it?
You should test the HDD with Drive Fitness Test. Download the CD image, burn it on a CD and boot from it:
http://www.hitachigst.com/hdd/support/download.htm#DFT
Check this and give us a feedback. Maybe the HDD must be replaced.
About the keyboard issue its not easy to say what causes the problem but in worst case it must replaced too. :(

How can I boot from my recovery dvd to reach the system recovery C: on a extern hard disc

I think a have a virus in my notebook Pavilion 15 and want to restore my C partition with a system back up. I made this system back up a month ago and it is stored on a extern hard disc. I have also made a recovery dvd. How can I boot my notebook from my dvd to start the procedure? I have 2 partions on my notebook. The second partition contains My Documents.
Thanks in advance.
Tineke

It is unlikely that the back-up of the system recovery, that you have stored on an external drive, will be useful in recovering your computer. Please see HP PCs - Performing an HP System Recovery (Windows 8), for instructions on using the HP Recovery Disc set your created earlier. Typically, the disc set is 4 to 6 DVDs.
If you have any further questions, please don't hesitate to ask.
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Can't boot after system update: unknown filesystem type

After running a system update, including updating the kernel, I can't boot to the new kernel.
On booting, grub loads the kernel image, runs/loads udev, but then fails to mount the root partition with error:
mount: unknown filesystem type 'ext4'
I have tried reinstalling the 'linux' package via packman several times, also trying the --recursive argument to make sure all my dependencies were there, and after days of googling and tweaking my system, I'm at a loss.
Thank goodness I happened to keep a spare kernel laying around in /boot.
Thanks in advance.
Last edited by jackrabbit (2012-03-22 23:25:28)

The OP can read their partition initially though, it's only after udev that they can't.
Also, try adding "rootfstype=ext4" to your grub kernel line. Is your /boot on a separate partition or part of your / partition?

I took the system file out of the system folder on os 9.2 can't boot to put file back in machine also has osx 10.2 but won't let me boot to either need os 9 compatible boot disk I think?

I took the system file out of the system folder on os 9.2 can't boot to put file back in machine also has osx 10.2 but won't let me boot to either need os 9 compatible boot disk I think?

If the OS X 10.2 on the hard drive is/was bootable, try this -
Restart or boot, then immediately press the X key, keep it held down until you know the machine has started to boot using OS X. This is a hardware instruction to the Mac to boot using the first usable instance of OS X it finds.
Once booted to OS X, you should be able to move OS 9's System file into OS 9's System Folder.
Note - in general, unless you know for sure what you are doing and that the results are desired, do not relocate or rename files in OS 9's System Folder or in OS X's System or Library folders.

Unsupported chassis type 52, system can not boot

I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots.
I am not aware if this spare had been used in production before.
Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.
Thanks,
Tom
The following is displayed on Console:
Exiting to ios...
Rommon reg: 0x0E000380
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(37)SG1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 30-Jul-07 13:47 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x11863D38
Unsupported chassis type 52, system can not boot
Rebooting in 10 seconds...
10 09 08 07 06 05 04 03 02 01
* Welcome to Rom Monitor for WS-X4516-10GE System.       *
* Copyright (c) 2003-2006 by Cisco Systems, Inc.         *
* All rights reserved.                                   *
Rom Monitor Program Version 12.2(31r)SGA
Supervisor: WS-X4516-10GE Chassis: WS-C4507R-E
Hardware Revisions - Board: 4.11 CPLD Tie: 32 FPGA Pod: 14
MAC Address : 00-11-21-ac-cf-b0
Ip Address   : Not set.
Netmask      : Not set.
Gateway      : Not set.
TftpServer   : Not set.

tffmaguire wrote:I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.Thanks,Tom
You don't have the right IOS version to meet the minimum requirements for this chassis.
See the following document
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet0900aecd801792b1.html
Table 5 lists 12.2(40)SG as the minimum IOS required for a 4507R-E chassis and 12.2(54)SG as the minimum IOS for a 4507R+E chassis. You only have 12.2(37)SG1 on your engine, hence the lack of boot.
Upgrade the IOS via ROMMON (slow and painful, but it'll work) and re-try.
Cheers.

Was working now not, Can not boot any more system error

I've got a Summer 2001 Snow iMac that was working under 10.3.9 but my attempt to back date has failed and now only get the classic OS 9 folder with a question mark which means can't find system files. It all started when I selected a OS 9.0.4 folder using the startup pref in 10.3.9 and now can't get it to do any thing. I have tried every thing I know but can't get it to boot up from the OS 9.0.4 or a 9.1 cd nor back to 10.3.9, not even holding down the option key works. The only thing I have are the two OS 9 disc, is there any thing I can do? I can get it to boot to the firmware mode but don't know any commands. PLease help.

A +Summer 2001+ iMac G3 cannot boot Mac OS 9.0.4. It came pre-installed with 9.1.
http://www.everymac.com/systems/apple/imac/stats/imac600graphite.html
Macs can generally boot a version of Mac OS that it came with, or LATER (up to hardware limitations), but NOT earlier. 9.0.4 is earlier than 9.1.
Try resetting PRAM.
http://support.apple.com/kb/HT1379
The startup disk setting is stored in PRAM. Resetting PRAM should clear the current setting and use a default choice (which hopefully will boot 10.3.9).
If that does not work, restart holding down the X key. That should force a restart with the installed Mac OS X system. If you get it to restart properly, trash that 9.0.4 system.

When I boot in safe or regular mode, I get this on my Macbook Pro with upgraded Mavrick System Unapproved caller. SecurityAgentmay only be invoked by Apple software. I can't boot my computer.

Unapproved caller. SecurityAgentmay only be invoked by Apple software. I just upgraded to Maverick and now I can't boot in regular or safe mode on my Macbook Pro.

I suggest you call Apple Care. However, the following is the BEST I can remember what I did as intructed by Apple Tech Support. I have a Time Machine Backup external hard drive.
Turn off computer
Turn on and @ first sign of life, press and hold the Option button
Follow the directions:
Click: Repair disk
Click: Repair Disk permissions
Get out of the section then pick the reinstall
Option reinstall
If that did not work: it did not for mine:
Do the same as above and click erase disk. If you have a Time Machine Back up, you can return you Mac back into working order w/your applications software, i.e. Word: mac 2008, Skype, etc.
Unplug you external hard drive to eliminate any possible confusion.
After an erase disk when starting like above (hold option button down while booting) and doing a total install,
Plug in your external drive with you Time Machine backups.
Only check applications and only users. Uncheck other files… and computer …
http://www.bing.com/search?q=macbook+migration&pc=MOZI&form=MOZSBR
After I did this, my computer went back to normal. Takes about a day. Good luck. It isn't easy and there are no short cuts I know of but better than having to find an Apple Store or shipping your Mac in for a repair.

Can't boot from DVD using C key

I desperately need to use DiskWarrior on my startup disk. I have used it on my secondary internal hard disk with no problems. A couple of years ago my Apple keyboard went up on me and I needed a replacement immediately (I worked from home), so I ran out to OfficeDepot and bought a Microsoft keyboard that had software with it to make it run with a Mac. It has done fine for me. However, when trying to boot from DiskWarrior, I hold the C key down and it doesn't boot from the DVD, it just boots from my internal startup disk. I was able to install Mac OS X 10.4 with the DVD and this keyboard, however. DiskWarrior tech support dudes tell me it is the fault of the Microsoft keyboard. I'm not so sure (since I installed 10.4 with this keyboard). I don't want to buy an Apple keyboard "just in case." But perhaps this is a known issue by somebody "out there." Any help would be appreciated (before my startup disk explodes altogether). Thanks!

I have 3 Microsoft keyboards, going back to my G4 MDD. Usually plugged into an Apple Display, but on some occassions I've had to plug it directly into front USB port (or rear, front is accessible).
The one thing that I would do, is not just "zap PRAM" from cold boot, but boot into the Open Firmware screen and RESET-NVRAM, and see if that helps. Force the device ID list to be rebuilt, and does a more complete job than zapping can.
There have been a lot of major problems with Apple USB hub type support. I too was troubleshooting an issue and got the "run around."
The only time I've seen where someone could not boot from a DVD/CD was when the hard drive in the system directory was severely corrupt - OS X looks to find any and all bootable devices even when you boot from CD or another drive. And a damaged journaling file is even harder to fix usually.
Outside of the G4 PCI model (1999, early '00) a G4 can boot from Firewire, any problem I'd guess was a defective FW port; some FW cases themselves.
I never really use DW CD. Always always clone your system; create an Emergency boot drive to work from - and used only in emergency so you know it works and isn't just a backup. And, of course, a backup of your working system.
USB cables can flake out. Even new. The USB extension cable Apple includes being one such that has been known to be the culprit. So doubt and verify any cables and devices.
One G5 owner has a LaCie drive not even connected, but the FW cable was, hanging out the back, and would cause:
slow boot sometimes; kernel panic other times; pull the cable, life is back to normal again. FW cables and devices (not sure if LaCie has the market cornered or not) that "wipe out" FW ports, cause shorts, should be avoided (maybe banned).
I've used an MS keyboard for about 4 yrs on my G4, still running 10.4.11. Ever since my Apple split ergonomic keyboard died, and I've got 4 Apple Pro keyboards sitting around (I can palm a basketball but don't like typing on small keyboards). Currently use MS 3000 and 4000 keyboards.
There are lots of reports of Leopard where the system is not responding, but the mouse able to move, but no interaction - can't launch anything or even bring up the Force Quit dialogue. The system being totally non-responsive, and people force shutdown, with high potential of leaving the directory in disrepair.
Mac OS 10.2.5 was suppose to fix and solve USB hub problem. That updated lasted less than two weeks. USB issues have been around, as have Firewire problems. Even Windows Vista can loose track of and get confused by unplugging/replugging devices multiple times that it looses the device ID.

[SOLVED] Can't boot Windows 8 using grub2. invalid EFI file path

English is not my native language. Please excuse typing errors.
I have just successfully installed Arch linux with grub2 as its boot manager. I
followed the arch beginner guide. I've used grub before and I'm familiar with
it, so chose to use grub instead for efistub. I installed os-prober and
ran grub-mkconfig to create the grub.cfg file. The problem now is that I recieve
an error when I try to boot windows 8. I have two drives (/dev/sda and /dev/sdb)
and I believe both are EFI-systems.
However, it's not very important for me to use grub, so if booting into windows
8 is easier using efistub, I will try that.
The computer is ASUS ux32vd with a hybrid disk with 25GB on the SSD and 500GB on
the hard drive. I believe the SSD part is used by Windows.
This is the first error I recieved when I tried to boot windows.
error: can't find command `drivemap'.
error: invalid EFI file path.
Press any key to continue...
Then I tried to follow this post
https://bbs.archlinux.org/viewtopic.php?id=150183 and made a new boot
entry "Windows 82". And I got a new error:
error: unspecified search type.
error: file '/EFI/Microsoft/Boot/bootmgfw.efi' not found
Press any key to continue...
Here are some command line outputs.
~ ᐅ sudo blkid
/dev/sdb1: PARTLABEL="HFS" PARTUUID="4613ee39-4727-4347-8134-173f590f716f"
/dev/sdb2: LABEL="INTELRST" UUID="BA5E-7431" TYPE="vfat" PARTLABEL="EFI system partition" PARTUUID="304f2630-89b2-4632-a566-e8c6db9df3a9"
/dev/sda1: LABEL="SYSTEM" UUID="90FA-5332" TYPE="vfat" PARTLABEL="EFI system partition" PARTUUID="5a60fff2-384a-4168-ad7b-7ba25c03c910"
/dev/sda2: LABEL="Recovery" UUID="ECE43E9AE43E674C" TYPE="ntfs" PARTLABEL="Basic data partition" PARTUUID="5da02b32-607a-4c63-88ef-00499bd6e05c"
/dev/sda3: PARTLABEL="Microsoft reserved partition" PARTUUID="6c501a91-71a5-45d8-a9ee-2e2a1c427258"
/dev/sda4: LABEL="OS" UUID="DE4241E84241C5CD" TYPE="ntfs" PARTLABEL="Basic data partition" PARTUUID="6e182189-b0e3-479a-ac74-8e69452d7c66"
/dev/sda5: LABEL="DATA" UUID="B05448EC5448B6BE" TYPE="ntfs" PARTLABEL="Basic data partition" PARTUUID="be7e04ac-fb01-44fd-9571-e0b001652322"
/dev/sda6: LABEL="Restore" UUID="B8D84520D844DDEE" TYPE="ntfs" PARTLABEL="Basic data partition" PARTUUID="4d42c26d-2c85-4ebf-88ec-7a83a4814a61"
/dev/sda7: LABEL="ROOT" UUID="0d63036d-b624-4596-a296-1db457c068d5" TYPE="ext4" PARTUUID="707f4bca-18b4-4340-838f-ec3a39e9338a"
/dev/sda8: UUID="bcaa2c5f-150d-47c9-9a58-9a7b7ec7bed2" TYPE="swap" PARTUUID="1da43668-418c-4883-810b-e1c3dee75e61"
~ ᐅ sudo lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 465.8G 0 disk
├─sda1 8:1 0 300M 0 part /boot/efi
├─sda2 8:2 0 600M 0 part
├─sda3 8:3 0 128M 0 part
├─sda4 8:4 0 186.3G 0 part /mnt/windows
├─sda5 8:5 0 190.1G 0 part /mnt/data
├─sda6 8:6 0 20G 0 part
├─sda7 8:7 0 66.5G 0 part /
└─sda8 8:8 0 1.9G 0 part
sdb 8:16 0 22.4G 0 disk
├─sdb1 8:17 0 18.4G 0 part
└─sdb2 8:18 0 4G 0 part
~ ᐅ sudo cat /boot/grub/grub.cfg
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="0"
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt7'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt7 --hint-efi=hd0,gpt7 --hint-baremetal=ahci0,gpt7 0d63036d-b624-4596-a296-1db457c068d5
else
search --no-floppy --fs-uuid --set=root 0d63036d-b624-4596-a296-1db457c068d5
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
set locale_dir=$prefix/locale
set lang=en_US
insmod gettext
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-0d63036d-b624-4596-a296-1db457c068d5' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt7'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt7 --hint-efi=hd0,gpt7 --hint-baremetal=ahci0,gpt7 0d63036d-b624-4596-a296-1db457c068d5
else
search --no-floppy --fs-uuid --set=root 0d63036d-b624-4596-a296-1db457c068d5
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=0d63036d-b624-4596-a296-1db457c068d5 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux.img
menuentry 'Arch Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-0d63036d-b624-4596-a296-1db457c068d5' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt7'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt7 --hint-efi=hd0,gpt7 --hint-baremetal=ahci0,gpt7 0d63036d-b624-4596-a296-1db457c068d5
else
search --no-floppy --fs-uuid --set=root 0d63036d-b624-4596-a296-1db457c068d5
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=0d63036d-b624-4596-a296-1db457c068d5 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/20_memtest86+ ###
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
menuentry 'Windows Recovery Environment (loader) (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-chain-ECE43E9AE43E674C' {
insmod part_gpt
insmod ntfs
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 ECE43E9AE43E674C
else
search --no-floppy --fs-uuid --set=root ECE43E9AE43E674C
fi
drivemap -s (hd0) ${root}
chainloader +1
menuentry 'Windows 8 (loader) (on /dev/sda4)' --class windows --class os $menuentry_id_option 'osprober-chain-DE4241E84241C5CD' {
insmod part_gpt
insmod ntfs
set root='hd0,gpt4'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt4 --hint-efi=hd0,gpt4 --hint-baremetal=ahci0,gpt4 DE4241E84241C5CD
else
search --no-floppy --fs-uuid --set=root DE4241E84241C5CD
fi
drivemap -s (hd0) ${root}
chainloader +1
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
#menuentry "Microsoft Windows 8 x86_64 UEFI-GPT NTFS" {
#insmod part_gpt
#insmod ntfs
#insmod search_fs_uuid
#insmod chain
#search --fs-uuid --set=root --hint-bios=hd0,gpt4 --hint-efi=hd0,gpt4 --hint-baremetal=ahci0,gpt4 DE4241E84241C5CD
#chainloader /EFI/Microsoft/Boot/bootmgfw.efi
menuentry "Windows 8" {
insmod part_gpt
insmod fat
insmod search_fs_uuid
insmod chain
search --no-floppy --fs--uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 90FA-5332
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
menuentry "Windows 8-2" --class windows --class os $menuentry_id_option 'osprober-chain-ECE43E9AE43E674C' {
insmod part_gpt
insmod fat
insmod search_fs_uuid
insmod chain
search --no-floppy --fs--uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 90FA-5332
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
~ ᐅ sudo grub-probe --target=fs_uuid /boot/efi/EFI/Microsoft/Boot/bootmgfw.efi
90FA-5332
~ ᐅ sudo grub-probe --target=hints_string /boot/efi/EFI/Microsoft/Boot/bootmgfw.efi
--hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1
bootinitscript
Boot Info Script 0.61 [1 April 2012]
============================= Boot Info Summary: ===============================
=> No boot loader is installed in the MBR of /dev/sda.
=> No boot loader is installed in the MBR of /dev/sdb.
sda1: __________________________________________________________________________
File system: vfat
Boot sector type: Unknown
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /efi/arch-grub/grubx64.efi /efi/Boot/bkpbootx64.efi
/efi/Boot/bootx64.efi /efi/ubuntu/grubx64.efi
sda2: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /bootmgr /Boot/BCD
sda3: __________________________________________________________________________
File system:
Boot sector type: -
Boot sector info:
Mounting failed: mount: unknown filesystem type ''
sda4: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe
sda5: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda6: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda7: __________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Arch Linux ()
Boot files: /boot/grub/grub.cfg /etc/fstab
sda8: __________________________________________________________________________
File system: swap
Boot sector type: -
Boot sector info:
sdb1: __________________________________________________________________________
File system:
Boot sector type: -
Boot sector info:
Mounting failed: mount: unknown filesystem type ''
mount: unknown filesystem type ''
sdb2: __________________________________________________________________________
File system: vfat
Boot sector type: Unknown
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
============================ Drive/Partition Info: =============================
Drive: sda _____________________________________________________________________
Disk /dev/sda: 500.1 GB, 500107862016 bytes, 976773168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sda1 1 976,773,167 976,773,167 ee GPT
GUID Partition Table detected.
Partition Start Sector End Sector # of Sectors System
/dev/sda1 2,048 616,447 614,400 EFI System partition
/dev/sda2 616,448 1,845,247 1,228,800 Windows Recovery Environment (Windows)
/dev/sda3 1,845,248 2,107,391 262,144 Microsoft Reserved Partition (Windows)
/dev/sda4 2,107,392 392,816,639 390,709,248 Data partition (Windows/Linux)
/dev/sda5 392,816,640 791,449,599 398,632,960 Data partition (Windows/Linux)
/dev/sda6 934,809,600 976,773,119 41,963,520 Windows Recovery Environment (Windows)
/dev/sda7 791,449,600 930,902,015 139,452,416 Data partition (Windows/Linux)
/dev/sda8 930,902,016 934,809,599 3,907,584 Swap partition (Linux)
Drive: sdb _____________________________________________________________________
Disk /dev/sdb: 24.0 GB, 24015495168 bytes, 46905264 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sdb1 1 4,294,967,295 4,294,967,295 ee GPT
/dev/sdb1 ends after the last sector of /dev/sdb
GUID Partition Table detected.
Partition Start Sector End Sector # of Sectors System
/dev/sdb1 8,392,704 46,903,295 38,510,592 -
/dev/sdb2 2,048 8,390,655 8,388,608 -
"blkid" output: ________________________________________________________________
Device UUID TYPE LABEL
/dev/sda1 90FA-5332 vfat SYSTEM
/dev/sda2 ECE43E9AE43E674C ntfs Recovery
/dev/sda3
/dev/sda4 DE4241E84241C5CD ntfs OS
/dev/sda5 B05448EC5448B6BE ntfs DATA
/dev/sda6 B8D84520D844DDEE ntfs Restore
/dev/sda7 0d63036d-b624-4596-a296-1db457c068d5 ext4 ROOT
/dev/sda8 bcaa2c5f-150d-47c9-9a58-9a7b7ec7bed2 swap
/dev/sdb1
/dev/sdb2 BA5E-7431 vfat INTELRST
================================ Mount points: =================================
Device Mount_Point Type Options
/dev/sda1 /boot/efi vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/sda4 /mnt/windows fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096)
/dev/sda5 /mnt/data fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096)
/dev/sda7 / ext4 (rw,relatime,commit=600,data=ordered)
=========================== sda7/boot/grub/grub.cfg: ===========================
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="0"
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt7'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt7 --hint-efi=hd0,gpt7 --hint-baremetal=ahci0,gpt7 0d63036d-b624-4596-a296-1db457c068d5
else
search --no-floppy --fs-uuid --set=root 0d63036d-b624-4596-a296-1db457c068d5
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
set locale_dir=$prefix/locale
set lang=en_US
insmod gettext
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-0d63036d-b624-4596-a296-1db457c068d5' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt7'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt7 --hint-efi=hd0,gpt7 --hint-baremetal=ahci0,gpt7 0d63036d-b624-4596-a296-1db457c068d5
else
search --no-floppy --fs-uuid --set=root 0d63036d-b624-4596-a296-1db457c068d5
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=0d63036d-b624-4596-a296-1db457c068d5 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux.img
menuentry 'Arch Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-0d63036d-b624-4596-a296-1db457c068d5' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt7'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt7 --hint-efi=hd0,gpt7 --hint-baremetal=ahci0,gpt7 0d63036d-b624-4596-a296-1db457c068d5
else
search --no-floppy --fs-uuid --set=root 0d63036d-b624-4596-a296-1db457c068d5
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=0d63036d-b624-4596-a296-1db457c068d5 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/20_memtest86+ ###
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
menuentry 'Windows Recovery Environment (loader) (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-chain-ECE43E9AE43E674C' {
insmod part_gpt
insmod ntfs
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 ECE43E9AE43E674C
else
search --no-floppy --fs-uuid --set=root ECE43E9AE43E674C
fi
drivemap -s (hd0) ${root}
chainloader +1
menuentry 'Windows 8 (loader) (on /dev/sda4)' --class windows --class os $menuentry_id_option 'osprober-chain-DE4241E84241C5CD' {
insmod part_gpt
insmod ntfs
set root='hd0,gpt4'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt4 --hint-efi=hd0,gpt4 --hint-baremetal=ahci0,gpt4 DE4241E84241C5CD
else
search --no-floppy --fs-uuid --set=root DE4241E84241C5CD
fi
drivemap -s (hd0) ${root}
chainloader +1
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
menuentry "Windows 8" {
insmod part_gpt
insmod fat
insmod search_fs_uuid
insmod chain
search --no-floppy --fs--uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 90FA-5332
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
menuentry 'Windows 82' --class windows --class os $menuentry_id_option 'osprober-chain-ECE43E9AE43E674C' {
insmod part_gpt
insmod fat
insmod search_fs_uuid
insmod chain
search --no-floppy --fs--uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 90FA-5332
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
=============================== sda7/etc/fstab: ================================
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda7 LABEL=ROOT
UUID=0d63036d-b624-4596-a296-1db457c068d5 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda1 LABEL=SYSTEM
UUID=90FA-5332 /boot/efi vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro 0 2
LABEL=DATA /mnt/data ntfs-3g uid=sighol,gid=users,dmask=022,fmask=133 0 0
LABEL=OS /mnt/windows ntfs-3g uid=sighol,gid=users,dmask=022,fmask=133 0 0
=================== sda7: Location of files loaded by Grub: ====================
GiB - GB File Fragment(s)
======================== Unknown MBRs/Boot Sectors/etc: ========================
Unknown GPT Partiton Type
5850cbb887c11947baf0379ca2d4c97e
Unknown GPT Partiton Type
dee2bfd3af3ddf11ba40e3a556d89593
Unknown BootLoader on sda1
00000000 eb 58 90 4d 53 44 4f 53 35 2e 30 00 02 08 5e 1b |.X.MSDOS5.0...^.|
00000010 02 00 00 00 00 f8 00 00 3f 00 ff 00 00 08 00 00 |........?.......|
00000020 00 60 09 00 51 02 00 00 00 00 00 00 02 00 00 00 |.`..Q...........|
00000030 01 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000040 80 01 29 32 53 fa 90 4e 4f 20 4e 41 4d 45 20 20 |..)2S..NO NAME |
00000050 20 20 46 41 54 33 32 20 20 20 33 c9 8e d1 bc f4 | FAT32 3.....|
00000060 7b 8e c1 8e d9 bd 00 7c 88 56 40 88 4e 02 8a 56 |{......|[email protected]|
00000070 40 b4 41 bb aa 55 cd 13 72 10 81 fb 55 aa 75 0a |@.A..U..r...U.u.|
00000080 f6 c1 01 74 05 fe 46 02 eb 2d 8a 56 40 b4 08 cd |...t..F..-.V@...|
00000090 13 73 05 b9 ff ff 8a f1 66 0f b6 c6 40 66 0f b6 |.s......f...@f..|
000000a0 d1 80 e2 3f f7 e2 86 cd c0 ed 06 41 66 0f b7 c9 |...?.......Af...|
000000b0 66 f7 e1 66 89 46 f8 83 7e 16 00 75 39 83 7e 2a |f..f.F..~..u9.~*|
000000c0 00 77 33 66 8b 46 1c 66 83 c0 0c bb 00 80 b9 01 |.w3f.F.f........|
000000d0 00 e8 2c 00 e9 a8 03 a1 f8 7d 80 c4 7c 8b f0 ac |..,......}..|...|
000000e0 84 c0 74 17 3c ff 74 09 b4 0e bb 07 00 cd 10 eb |..t.<.t.........|
000000f0 ee a1 fa 7d eb e4 a1 7d 80 eb df 98 cd 16 cd 19 |...}...}........|
00000100 66 60 80 7e 02 00 0f 84 20 00 66 6a 00 66 50 06 |f`.~.... .fj.fP.|
00000110 53 66 68 10 00 01 00 b4 42 8a 56 40 8b f4 cd 13 |Sfh.....B.V@....|
00000120 66 58 66 58 66 58 66 58 eb 33 66 3b 46 f8 72 03 |fXfXfXfX.3f;F.r.|
00000130 f9 eb 2a 66 33 d2 66 0f b7 4e 18 66 f7 f1 fe c2 |..*f3.f..N.f....|
00000140 8a ca 66 8b d0 66 c1 ea 10 f7 76 1a 86 d6 8a 56 |..f..f....v....V|
00000150 40 8a e8 c0 e4 06 0a cc b8 01 02 cd 13 66 61 0f |@............fa.|
00000160 82 74 ff 81 c3 00 02 66 40 49 75 94 c3 42 4f 4f |[email protected]|
00000170 54 4d 47 52 20 20 20 20 00 00 00 00 00 00 00 00 |TMGR ........|
00000180 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000001a0 00 00 00 00 00 00 00 00 00 00 00 00 0d 0a 44 69 |..............Di|
000001b0 73 6b 20 65 72 72 6f 72 ff 0d 0a 50 72 65 73 73 |sk error...Press|
000001c0 20 61 6e 79 20 6b 65 79 20 74 6f 20 72 65 73 74 | any key to rest|
000001d0 61 72 74 0d 0a 00 00 00 00 00 00 00 00 00 00 00 |art.............|
000001e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000001f0 00 00 00 00 00 00 00 00 ac 01 b9 01 00 00 55 aa |..............U.|
00000200
Unknown BootLoader on sdb2
00000000 eb 58 90 4d 53 44 4f 53 35 2e 30 00 02 08 2e 20 |.X.MSDOS5.0.... |
00000010 02 00 00 00 00 f8 00 00 3f 00 ff 00 00 08 00 00 |........?.......|
00000020 00 00 80 00 e9 1f 00 00 00 00 00 00 02 00 00 00 |................|
00000030 01 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000040 80 00 29 31 74 5e ba 4e 4f 20 4e 41 4d 45 20 20 |..)1t^.NO NAME |
00000050 20 20 46 41 54 33 32 20 20 20 33 c9 8e d1 bc f4 | FAT32 3.....|
00000060 7b 8e c1 8e d9 bd 00 7c 88 56 40 88 4e 02 8a 56 |{......|[email protected]|
00000070 40 b4 41 bb aa 55 cd 13 72 10 81 fb 55 aa 75 0a |@.A..U..r...U.u.|
00000080 f6 c1 01 74 05 fe 46 02 eb 2d 8a 56 40 b4 08 cd |...t..F..-.V@...|
00000090 13 73 05 b9 ff ff 8a f1 66 0f b6 c6 40 66 0f b6 |.s......f...@f..|
000000a0 d1 80 e2 3f f7 e2 86 cd c0 ed 06 41 66 0f b7 c9 |...?.......Af...|
000000b0 66 f7 e1 66 89 46 f8 83 7e 16 00 75 39 83 7e 2a |f..f.F..~..u9.~*|
000000c0 00 77 33 66 8b 46 1c 66 83 c0 0c bb 00 80 b9 01 |.w3f.F.f........|
000000d0 00 e8 2c 00 e9 a8 03 a1 f8 7d 80 c4 7c 8b f0 ac |..,......}..|...|
000000e0 84 c0 74 17 3c ff 74 09 b4 0e bb 07 00 cd 10 eb |..t.<.t.........|
000000f0 ee a1 fa 7d eb e4 a1 7d 80 eb df 98 cd 16 cd 19 |...}...}........|
00000100 66 60 80 7e 02 00 0f 84 20 00 66 6a 00 66 50 06 |f`.~.... .fj.fP.|
00000110 53 66 68 10 00 01 00 b4 42 8a 56 40 8b f4 cd 13 |Sfh.....B.V@....|
00000120 66 58 66 58 66 58 66 58 eb 33 66 3b 46 f8 72 03 |fXfXfXfX.3f;F.r.|
00000130 f9 eb 2a 66 33 d2 66 0f b7 4e 18 66 f7 f1 fe c2 |..*f3.f..N.f....|
00000140 8a ca 66 8b d0 66 c1 ea 10 f7 76 1a 86 d6 8a 56 |..f..f....v....V|
00000150 40 8a e8 c0 e4 06 0a cc b8 01 02 cd 13 66 61 0f |@............fa.|
00000160 82 74 ff 81 c3 00 02 66 40 49 75 94 c3 42 4f 4f |[email protected]|
00000170 54 4d 47 52 20 20 20 20 00 00 00 00 00 00 00 00 |TMGR ........|
00000180 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000001a0 00 00 00 00 00 00 00 00 00 00 00 00 0d 0a 44 69 |..............Di|
000001b0 73 6b 20 65 72 72 6f 72 ff 0d 0a 50 72 65 73 73 |sk error...Press|
000001c0 20 61 6e 79 20 6b 65 79 20 74 6f 20 72 65 73 74 | any key to rest|
000001d0 61 72 74 0d 0a 00 00 00 00 00 00 00 00 00 00 00 |art.............|
000001e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000001f0 00 00 00 00 00 00 00 00 ac 01 b9 01 00 00 55 aa |..............U.|
00000200
========= Devices which don't seem to have a corresponding hard drive: =========
sdc {
=============================== StdErr Messages: ===============================
cat: /tmp/BootInfo-wSbit3X4/Tmp_Log: No such file or directory
/dev/sdc: open failed: No medium found
No volume groups found
mdadm: No arrays found in config file or automatically
EDIT:
I gave up trying to make grub work, so I uninstalled grub and deleted all the grub files I could find.
# pacrem grub-efi-x86_64
# rm -fr /boot/grub
That last one I came to regret later on. So I installed rEFInd using the archlinux beginners guide. When I then tried to boot into windows It told me that /boot/grub/x86_64-efi/normal.mod was not found. I then reinstalled grub-efi-x86_64 and copied /usr/lib/grub/x86_64 to /boot/grub. Now everything works fine.
Last edited by sighol (2013-06-08 21:47:49)

sighol wrote:However, it's not very important for me to use grub, so if booting into windows
8 is easier using efistub, I will try that.
The EFI stub loader is a Linux-only boot loader; however, it is possible to use the EFI stub loader in conjunction with a separate boot manager, such as rEFInd or gummiboot. In such a configuration, you'd use the boot manager to select the OS to boot (Windows or Linux, and possibly the specific Linux kernel), and the boot loader (the Windows loader or the EFI stub loader built into a specific kernel) will then take over booting the OS. In Arch, this is often easier to configure than is GRUB, since GRUB is very complex and its automated tools to help with setting things up often get it wrong.
This is the first error I recieved when I tried to boot windows.
error: can't find command `drivemap'.
error: invalid EFI file path.
Press any key to continue...
The "drivemap" command in GRUB is generally used when booting a BIOS-mode boot loader, and in fact your "Windows Recovery Environment (loader) (on /dev/sda2)" and "Windows 8 (loader) (on /dev/sda4)" GRUB entries are both built as for BIOS-mode Windows installations -- but the fact that your disks both use GPT means that Windows won't boot in BIOS mode on your computer. (This is one of the many things that the GRUB setup scripts can get wrong.)
Then I tried to follow this post
https://bbs.archlinux.org/viewtopic.php?id=150183 and made a new boot
entry "Windows 82". And I got a new error:
error: unspecified search type.
error: file '/EFI/Microsoft/Boot/bootmgfw.efi' not found
Press any key to continue...
Both your "Windows 8" and "Windows 82" entries refer to an EFI boot loader file called EFI/Microsoft/Boot/bootmgfw.efi on your EFI System Partition (ESP). This should be correct, but your Boot Info Script output doesn't show any evidence of such a file. Sometimes Boot Info Script misses such things, so you may want to check it just to be sure. Your ESP is /dev/sda1, and it looks like it's being mounted at /boot/efi by default, so check for the /boot/efi/EFI/Microsoft directory tree, and for /boot/efi/EFI/Microsoft/Boot/bootmgfw.efi in particular. If that file isn't present, then something is wrong -- perhaps you mistakenly erased the ESP when you installed Linux, thus wiping out the Windows boot loader; or perhaps the file was accidentally deleted somewhere along the way. (Note that on FAT, which the ESP uses, case is irrelevant, and in fact case varies between the filenames reported by Boot Info Script and what's recorded in your configuration files.)
You do have another boot loader file that may be a duplicate of the Windows boot loader: EFI/BOOT/bkpbootx64.efi. This filename is generally created by Ubuntu's "Boot Repair" tool, which IMHO can do as much harm as good, especially on a system that's not booting Ubuntu. If you ran this tool, though, it's conceivable that bkpbootx64.efi is a copy of the Windows boot loader, so copying it to EFI/Microsoft/Boot/bootmgfw.efi might get things working. OTOH, the Windows boot loader relies on other files to do its job, so if they're not present, copying the Windows boot loader to its original location won't be sufficient.
If you can't get things working based on the preceding suggestions, I recommend you run a Windows repair tool. These are accessible from a Windows recovery disc. Such disc images are readily available on the Internet, but I don't happen to have any links handy. Try Microsoft's own site; images obtained from random third-party sites might contain malware. Once you've done this, chances are the computer will boot directly into Windows. You'll then need to either restore GRUB as the default boot loader or install another boot loader or boot manager. You can use the Windows "bcdedit" command to do the former, as in:
bcdedit /set {bootmgr} path \EFI\arch-grub\grubx64.efi
You'll need to type this from an Administrator Command Prompt window.

Can't Boot From Install Disc 1 ?

Holding down "C" at Start Up isn't working.
Most of the time I can't get Preferences > Start-Up to even "see" my Disc 1.
When I can get it to show up in Start-Up, and Select it, and Lock it ... it Still Won't Start Up from the Install Disc 1 ... and in fact usually ejects the disc.
Sometimes when I re-push in the disc, I get the message that a Blank Disc has been detected, "what do you want to do with it."
But, it shows up in Disc Utility, and when I run Verify Disc, it all looks good?!
The Disc has Mac OS version 10.4.8 on it. I'm running 10.5.7. I'm all up to date with my software.
Yesterday I ran the latest version of Disc Warrior. When I run TechTools 4.0 it seems to get stuck running Files. When I run Repair Permissions from Disc Utilities, it shows a fairly massive amount of issues. Running it over and over again doesn't seem to make any difference.
I WANT to run my Install Disc so I can run Repair Disc from Disc Utility ... because I'm having a number of issues ... and I seem to get the spinning rainbow a lot.
SUGGESTIONS ?! ... thanks ...

Disk Utility that can repair a 10.5.7 permissions is only found on the Leopard installer disc. Tiger can't repair Leopard when it comes to permissions, and may also have difficulty with the directory.
Secondly, if your MacBook Pro was purchased after October 26, 2007, it can't boot from any Tiger disc.
If your MacBook Pro was purchased prior, you can use the disk, but you'll want to follow these directions for hardware diagnostics:
http://docs.info.apple.com/article.html?artnum=303081
Only if your MacBook Pro has Tiger installed, should you use Tiger for the directory or permissions*:
http://www.macmaps.com/directoryfaq.html
Macs can only boot from the operating system that shipped with them, and newer retail operating systems. This means:
1. pre-October 1st, 2007 MacBook Pros can boot off:
- - the discs that shipped with them
- - retail 10.5 discs which look like * that do not say Upgrade, DropIn, or OEM.
2. October 1st through October 25, 2007 can do #1, and also use Upgrade and DropIn discs. Those disks were offered as a limited time mail order Up to date program, some were dropped in the box that came with them.
3. October 26th through November 14, 2007 can boot off the discs that came with them, and retail 10.5.1, 10.5.4, and 10.5.6 discs that do not say Upgrade, DropIn, or OEM, and have a label like the image above.
4. November 15, 2007 through June 29, 2008 can boot off the discs that came with them, and the retail 10.5.4, and 10.5.6 discs that do not say Upgrade, DropIn, or OEM, and have a label like the image above.
5. June 30, 2008 through December 14, 2008 can boot off the discs that came with them, and the retail 10.5.6 discs that do not say Upgrade, DropIn, or OEM, and have a label like the image above.
6. December 15, 2008 and later MacBook Pros can only boot off the discs that came with them.
Presumably when Snow Leopard comes out in September, all of the above will be able to use Snow Leopard because of the specs on http://www.apple.com/macosx/specs.html
- * Links to my pages may give me compensation.
Message was edited by: a brody

Can't boot from OSX cd - Kernel Panic or bad CPU?

Greetings, All! I've looked at all the articles related to this that I can find, here and on other sites, but have not been able to solve the problem. Here's a list to briefly describe my issue:
-Got Prohibitory sign on my MDD Dual 867 when I tried booting into OS X (10.3).
-Tried all the resets (PRAM, PMU), re-seated RAM, took out RAM, etc.
-Trashed OS, and tried to re-install, but Mac won't boot from DVD (10.3) or CD (10.2) - just get the spinning wheel and finally Prohibitory sign...
-Ran Hardware test to loop for about 17 hours; nothing, all fine.
Then I just recently noticed that when I run Digital Performer 3 (OS9), it usually shows 2 usage indicators for CPU performance (1 for each processor) but now only shows one. So, I'm thinking a processor may have died, or become unseated, or something. But I read somewhere, on one of the forums, that it isn't likely for one of a pair of processors to go, or if it did, the other wouldn't be able to function solo. But if that weren't the case, and the Mac can run on 1 processor, why would that keep the Mac from booting from the OSX disk?
The Mac still runs fine in OS9, though it does seem to be a little slower when I do processor-intensive operations in DP, and sometimes hangs on startup, and seems to have some "sleep" issues (won't wake back up sometimes...). I don't know of any way to check if both processors are functioning in OS9. Does anyone know of a utility that will do that? Or if there's one in the OS (The Profiler only shows processor speed)? And would that cause the Kernel Panic and keep the Mac from booting in OSX? It's very frustrating. I appreciate any help or tips anyone may have to offer. Peace, Gelon

Hey Guys!
I think I know the "why", but not the solution...
I have a PowerMac G4 400Mhz Dual Processor, and some day I had the same troubles. No boot on OS X, but I can in OS9. Checking the Open Firmware commands, I saw one of the processor marked as "dead". So, (dont't ask how) I removed one processor from the logic board. Now I got the same "Processor dead", I can boot on OS9, (with an alert for the processor) but is stable. No boot in OS X.
So, what I suposse (having the same reports in PC computers trying to run OS X) is that the OS X checks for the compliance of the System for running. When a processor fails, the OS X can not recognize the system as valid (as in some PC computers happens) and can not boot. I also suposse if we can get a "patched" OS X for PowerPC or patch the firmware in any way, we can work with just one processor. Or, buying a new processor for the Mac.
Pls. send me your comments.
LY

I Desperately Need Help - Can't Boot my iMac

Greetings Everyone. My apologies for making my debut on this board with a desperate plea for help but I think I just killed my iMac right in the middle of an important project. I'm accessing this board with my laptop PC (and you know I'm in a bad way when I have to revert to anything PC!)
I was trying to move some photos from iPhoto onto a CD. One photo would not move - computer said it was 'busy.' I couldn't delete it or anything so I force quit to see if I could start over.
The machine did reboot okay, so I thought perhaps I should try to restart in in OS9 (Im using 10.3.8 or 9 (can't remember and can't boot to confirm.) because I read somewhere that sometimes rebooting in OS9 will correct whatever has 'hung' in X - for lack of a better description.
Well, that's when it crashed. When I try to boot it the entrance sound makes its bong and the the light blue screen comes on and just sits there and does nothing, no matter how long I wait.
I tried to force boot it by holding in the start button until the list of instructions came on the screen. Tried typing mac-boot as instructed, and nothing happened. I tried three times. Then I tried shut-down and it did shut down.
That's as far as I can get. I hold in the start button until it makes a beeping noise, then it bongs, then the blue screen comes on and just sits there.
Have I fried my machine or is there any hope?
Can you tell I'm just about frantic???
Thanks for your patience. Any help would be greatly appreciated. I live in a fairly remote rural area with no Mac dealers within 200 kms - so I'm really stuck on this one.

Tried a few more tricks and finally got it to boot.
I held down the P R Apple & Option keys and waited for the second chimes. Nothing happened.
I disconnected everything but the mouse and keyboard and tried rebooting again.
Lo and Behold it worked.
I think the HP printer cable might be faulty, but don't know for sure what is actually going on.
This whole problem started because my printer suddenly died. I tried to remove then reload the software but kept getting the message that no device was attached, even though it was.
So I decided to save all my hard drive info onto CD's then reload the system software. Everything came to a halt when I couldn't delete the 'busy' image.
So for now, I'm back in business. Whew!
If anyone has any idea what on earth is going on I'd sure like to know. Do printer cables just go bonkers for no reason? And why would an image from iPhoto be 'busy' when I tried to delete it. Is that image doing something naughty that I need to know about?
I think I need a nice cold beer!

U460 can't boot up

I can't boot up the laptop. Its only 5 months since I bought its and seldom used.
Here's the scenario. I click on the power button, then the top right 3 icons light up. The next moment, I hear a "tick" sound, and the laptop shuts off.
This happens with/ without the battery + the charger. But with the battery, after plugging in/out the charger and starting it up multiple times. I manage to get it to boot up, and the system runs as per normal. Restarting it works fine as well. Once I shutdown the laptop,remove the charger, after sometime.. the same problem comes back again.
Its not the battery because its fully charged when I manage to boot it up.
Any idea what's happening?

try to perform clean windows installation first. check download page for bios updates.
if windows loads, try to use disk check for errors. also, do not forget to check system logs for errors.
( right click my computer > manage > event logs )
post back the results.
if issue persists, you may have power or hard disk issue.i suggest you to call support line.

My system sometime can't boot

Similar Messages

Maybe you are looking for