My T40 display (lcd) suddenly turns blank, any help

My T40 display (lcd) suddenly turns blank, any help Mo
Moderator Note; please update your profile with your correct country location as per the forum rules. Products, options and services vary from market to market. Knowing your location helps us help you
Message Edited by andyP on 07-12-2008 10:01 PM

I'm afraid that you're not going to like what I'm about to write...
Your T40 has most likely become a victim of the infamous GPU failure that T4x/R5x with ATi graphics are infamous for, where the video card starts detaching itself from the motherboard as a result of  heating/cooling cycles and/or physical stress on the chassis.
Re-flowing/re-balling the solder in the GPU area or motherboard replecement are your only choices.
Good luck and let us know. 
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Similar Messages

  • Apart from the lock button problem in iphone 5 the display brightness suddenly goes blank and becomes normal after locking and unlocking the iphone. The Apple service centre in India is denying to service the iphone as it was purchase in USA even thoug it

    Apart from the lock button problem in iphone 5 the display brightness suddenly goes blank and becomes normal after locking and unlocking the iphone. The Apple service centre in India is denying to service the iphone as it was purchase in USA even though the iphone is in warranty.

    iPhones do not have an international warranty.  Warranty is valid only for the country of purchase.  This is most likely because different countries require different iPhone models.  Not reasonable to expect all countries to maintain stock for all models.

  • Losing connection to external drives, tried disc utility got a message "No live updatin...? Retried new connections; is there a way to test the external usb hub?  The drives will occasionally display in Apple profile.  Any help would be deeply appreciated

    Losing connection to external drives, tried disc utility got a message "No live updatin...? Retried new connections; is there a way to test the external usb hub?  The drives will occasionally display in Apple profile.  Any help would be deeply appreciated

    It's not just you, I can't authorise my phone. It seemed to go down just after I started the update (it wasn't my fault though). I am using chrome, and it does not seem to be a firewall issue, or the bannerblock issue that I read about else where, since I dont have that program installed. Strange though how the support forum is still running. If I go to http://www.apple.com/support I get nothing, but googling topics allows me to see em.

  • CD/DVD does not play audio CD,it does play DVD and in rare ocasions it plays the audio CD but mainly if the computer is just turn on,any help will be very usefull,THANKS in advance it's a PowerBook G4

    PowerBook G4
    Problem with CD/DVD doesn't play audio CD but it does play DVD, and today it play audio CD but after ejected it did not play it again and ejected automatic.
    Any help grately apreciated Thanks in advance.

    Hello,
    Sounds to me like there is a problem with the optical drive. I would recommend replacing it.
    Have you tried to cleaning it?

  • Nearly all images suddenly turned corrupt - please help me

    hello
    I am working on a very important document, a kind of a final assignment which will help me pass my last year of school. I had about 22 pages done when I had to restart my computer because it suddenly seemed to be getting really slow. After I restarted it and reopened my pages document, most of the pictures on the pages I worked on today were gone and instead replaced by those grey blocks with a question mark in it, and some of them just left their "mask" at the place where they used to be. The pages I worked on the other day remained the same.
    Now that wouldn't be as much of a problem if I would be able to once again replace the grey blocks with the pictures that used to be in there. But trying to do this, pages tells me that the file is corrupt - other pictures still work, but pictures that used to be in those spots suddenly seem to be corrupt. However, I can still use them in other programs such as preview, word and so on...
    I'm in desperate need of help and I would be very glad if somebody would know a solution to my problem.
    Thanks in advance!
    Remo Berger

    thanks for the advice.
    I did find the pictures stored in this folder. They are just fine... what do you mean with XML and is there something I can do to restore it and get it back to normal?
    I found out that if I open a new pages document and add a blank page as its first page, then copy all of the pictures that disappeared in the original document on this page, then copy the pages of the old document under the blank page with all the pictures, those pictures reappear on those pages.
    Kind of confusing :P I hope you understand what I'm trying to describe here...

  • HT1349 My ipod was on charge and the wire sparked eversince it wont turn on any help?

    my ipod touch was on charge and the wire spaked eversince it wont turn on? any help

    Hi Ajburmy,
    You should contact Apple, either by calling the appropriate phone number on this page or by carrying in the iPod and charger to an Apple retail store. As this is at least potentially a safety issue (because of the sparking) I am certain that they will at least want to hear about it.
    Whatever you do, don't use the iPod or charger until Apple has said it is okay.
    Best of luck.

  • My phone was at 100% and won't turn on, any help?

    I charged my phone early in the afternoon and fell asleep to my phone being 100% on battery, I unplugged it and just sent 1 text and after about 2-3 hours later, my phone was warm and it wouldn't turn on. I tried the home + sleep button thing and it turned back on. why did my phone just decide to die even though it was at 100%?

    It may not be that your iPhone died, it probably just powered off for no apparent reason or explanation. If you're really concerned about this, I would use this article http://support.apple.com/kb/HT1414 to restore your iPhone and restore form an iCloud backup if you have one.

  • Ipod Video 30g wont turn on, any help why please?

    So I have found this old ipod video I must have got when it first came out. It has been a while since it has been used, and it may be heavily damaged, I am not sure. But when I press any button it remains on the Apple loading screen, as in the dark background with a dimly lit apple logo. This ipod is way past any warranty, and I am trying to do a self repair to save some money. I already tried charging it no luck. I connected it to the computer and my computer never recognized it, I reset it (menu and select) no luck, put it in disc mode (pause/play and select) no luck. But the screen stays on at the Apple logo. Can anybody tell me how I can fix this problem or what is the cause of it. Thank you very much.
    PS I am from Chicago so if anyone knows of any places that can help me for cheap let me know.

    actually i tryed doing the thing where u hold put the usb cord into the ipod while holding the home button and i tryed to restore it and it came up with in error that said that its not eligible for the requested build. i dont have the newest version of itunes on my mac and i heard u need the newest version to get the newest software for the ipod touch and it said restore and UPDATE in the beginning so maybe thats the problem? idk plzzz someone help me!!
    my last post has already been resolved so dont bother with that.

  • Nokia BH-505 doesn't turn on - Any help?

    My 7 months old Nokia BH-505 has already been replaced one. Now when it has no warranty , another problem has crept up. After getting fully charged, my headset is refusing to turn on. I've tried hard reset and draining its battery by keeping uncharged for couple of days. Nothing seems to work. When I took it to Nokia Care Centre, they refused to have a look at it by giving the explanation that it is not under warranty and accesssories are only replaced not repaired. I am very frustrated at Nokia for providing such pathetic service. This is my last resort to get a solution to fix this issue. So, please give me some suggestions to solve this issue.

    Worked for me man....awsome......I thought my 905 just got busted hardware wise, but then I did the multifunction (Pause/Play Key) + Rewind + Vol Down trick for ten seconds (Keep those buttons pressed for 10 seconds with the head set fully charged and ANC off) Then release buttons and power it on normally.......it worked like a charm for me. Man when expensive stuff like that go on the fritz they just bring you down.

  • My airport suddenly turned off. Help!

    Who can help me sold the above problem?  Thanks.

    If you have tried this on another AC socket that you know is working and get the same results, I cannot help.
    Take the AirPort Extreme to an Apple Store....if you have one in your area....or contact Apple directly for a replacement.
    http://www.apple.com/support/contact/
    If the modem will not power on, you will likely need to contact your Internet Service Provider if they furnished the modem to you.

  • My iPhone 4S, completely shut down for about an hour and won't turn on, any help?

    I am quite worried due to the fact I have over 400 photos.

    Try this First...
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    Wait for the Apple logo to Appear...
    Usually takes about 15 - 20 Seconds... ( But can take Longer...)
    Release the Buttons...
    http://support.apple.com/kb/ht1430
    More Info here...
    https://discussions.apple.com/message/19521062
    See Here for  >  Frozen or unresponsive iPhone

  • Macbook display suddenly turns black

    My macbook was working just fine, and I was surfing the net when the display would suddenly turn black, everything is still running, and if I look closely, the screen is just very dark, but i can still see a little bit, I have to press f1 and f2 a few times to get it back to normal.
    It happened the first time last night, and it already happened three times since I turned it on today
    Is this a common problem?

    macbig wrote:
    This sounds like a known issue with the Graphics card: http://www.pjentrepreneur.com/2009/01/21/update-mac-book-pro-blank-screen-proble m/
    Message was edited by: macbig
    That coverage is for the MacBook Pro, not a 2006 MacBook.
    +Website Says:+
    These are Mac Book Pros manufactured between May 2007 and September 2008.
    It could be an issue I've seen with a bad backlight. Try moving the screen in small increments all the way back and all the way forward. This may trigger the screen to go blank. It's either a bad connection between with the display or the LCD has gone bad.
    Your MacBook is out of warranty so there might be a cost if you go to an Apple Store to get it fixed. http://www.apple.com/retail/geniusbar to visit a store (if you are in the US. If not I can give you additional information)
    Ben

  • External Display will not turn back on after sleep

    Just bought a new MBP last week and gave my wife the MB. I typically attach to an external 24" display and run in closed clamshell mode. I have been doing it for quite some time with no issues. Now with the new MBP if the energy saver kicks in and turns off the display, and/or the energy saver puts the computer to sleep when I attempt to wake it up the display flashes then goes blank. There is no way to turn it back on. When I open the clamshell the internal display will only show some random pixels and a white line at the top of the screen. There is no way to correct it unless I shut down the machine.
    I am running with the Nvidia card, not the internal Nvidia. If I manually put the computer to sleep it will wake normally with no screen issues. It will also not act up if the external display is not connected.
    Any help or suggestions of a setting I might have wrong that would cause this?

    It is a Gateway FHD2400. Connected from mini display to HDMI. My previous MB was connected to the same monitor for the last year with 0 issues. It was connected mini dvi to VGA.
    The issue is strange because it only happens when the computer turns off the screen or sleep. When I put it in sleep it doesn't happen.

  • Screen turns blank all it sudden...

    I installed SL on a MBP all went normal, but now all it sudden the screen turns black. All I can do is to push the power on/off button till it reboots.
    All works fine and then all it sudden I loose the screen again.
    I was on skype with a friend while it happened, sound and everything else was still going fine, only the screen turned black (actually very dark gray).
    This happens since I installed SL, it does get a little better (had waaay more blank outs shortly after the install) but I normally don't get more then maybe 30 minutes out of the laptop before I have to restart it again.
    Any ideas? Any help?
    Sure appreciated.
    Thanks

    I had a similar experience this weekend. First road trip with my MBP converted to SL. I normally get the "you are running on reserve power" notification when I'm running low, but when watching movies on the flight out and back, the computer spontaneously went black - I thought it had shut down out of power. But both times when I later turned it back on I had more than 25% power still remaining. I was thinking it was some kind of problem between the DVD player app and low power notification, but after reading this I am wondering if the screen simply went black as is being described. Unfortunately I did not even try to reboot it after it went dead, assuming it was simply out of power.
    Picking up the 'book and putting it back in my briefcase it did not feel overly or unusually warm. On the way out I was running with an external drive connected to the 'book and on the way back I was watching a DVD ... so the only interesting symptom was that in both cases power usage was a little more (or at least different) than normal (I usually watch movies right from the hard drive). The worst thing is that the spontaneous shutdown on the way out seemed to have killed my little external drive - I mean dead. Can't even find it at all in Disk Utility - pretty weird, but that smacks of some kind of power event as well.

  • My macbook pro suddenly turn off and now when I turn it on the display doesn't work but it is on!

    Hello everyone,
    My macbook pro 15" suddenly turned off. Now i tried several time to switch it on and seems it is working but the display doesn't function or there are many wired pictures coming up sometimes.
    can anyone please help me with this issue?
    Thanks

    Welcome to the Apple Support Communities
    Your Mac can't find any bootable partition.
    1. Insert the Mac OS X DVD that came with the Mac and press C key while your Mac is starting.
    2. Select Utilities > Disk Utility, choose Macintosh HD in the sidebar and repair the disk. If it doesn't work, take the Mac to an Apple Store.
    Also, open  > Startup Disk, select Macintosh HD and restart. Maybe your Mac has forgotten the startup partition

Maybe you are looking for

  • Xorg.conf Acer Aspire 3000 xinerama [request][SOLVED]

    Anyone having an acer aspire 3000 laptop with xinerama working? Or anyone with a "sis" driver laptop with xinerama? I would be very very grateful if someone could post a working xorg.conf file with xinerama working for any of the above setups. Been s

  • I Want to connect to database . plz help

    dear programmers i use forms9i and oracle database 9i under winxp. the database is on the local machine . to connect database from the form i do the following: 1-choose file | connect from the main menue 2-type scott/tiger then click on connect the f

  • Enumeration of services in services.msc console issue

    Hi, I was given a task to allow non-admin users to restart MSSQLSERVER service on Windows Server 2003 R2 computer which was old core banking database server now used only for finding some archives in SQL databases. I have done the following steps: Gr

  • Problems exporting RAW + JPEG Pairs

    I have imported my images as RAW + JPEG Pairs (JPEG is Master) When I try to export originals, there are two problems: 1.  Aperture exports both the JPEG and the RAW file.  Is there anyway to force it to export just the file that is set as the master

  • SCD Type 2 Framework

    Hi: We are in the process of creating a data mart. We decided to use SCD Type 2 for dimensions. I read the SCD 2 transformation logic framework from Oracle Warehouse Builder. Is there any new framework available for this? I also read Chris Busch's fr