My tablet is just blinking red light - won't charge

HIello.. I tried the rebot thing.. but no luck.  The only receipt I have is the one showing on my American Express card.. help!!!

Connect to the wall charger the it came with for about 20 mins and try the 3 button reset.
Be a Shepard and not an iSheep.

Similar Messages

  • After upgrade attempt for 8310, device will not restart -- only blinking red light

    Problem: I tried to upgrade the device software to 4.5, and now THE DEVICE WILL NOT RESTART AT ALL. Not with a hard reset. Not using the SIM and battery from my 8310 and putting it in hers. Nothing. Just a red light that blinks in a pattern: two quick blinks, then a pause; two quick blinks, then a pause, etc.
    Background: This 8310 had vers. 4.2.2 device software, and something like 2.6 on the desktop. I downloaded/upgraded to 4.6 for the desktop and 4.5 for the device from the AT&T site. The Desktop manager prompted me to install the new device software... looking good. After several minutes, I got an "unknown error" message and it stopped the install.Following a support article, I uninstalled reinstalled both updates, but then the problem occurred: no NOTHING happens on the device screen at all, just the blinking red light when the device is plugged in.
    The AT&T store tells me this is about the tenth "dead" Curve he's seen in about a week, apparently all occurring when folks have attempted a software updgrade. Any thoughts/help to offer?
    Please help!
    Solved!
    Go to Solution.

    Check this instruction:
    http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry

  • HELP! Double blinking red light

    I was in the middle of upgrading the software on my curve 8330, the software stopped doing anything, and now my phone is off and just has a double blinking red light.
    I figure its now dead, but how can i fix this using my mac?
    I see plenty of instructions on how to load a new OS using a PC, but none for a mac
    Any help would be greatly appreciated!

    Welcome to the forums
    It seems you may have wiped the OS due to the accidental shut down. Try pulling your battery out and reinserting it to see if the phone boots up. If not, see how to restore a bricked blackberry: http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
    If you have a recent backup, you can load it onto the phone once you are done.
    Kijana
    Please remember to:
    1. Mark Accept as Solution on the appropriate post once your issue has been resolved
    2. Give Kudos to helpful posts (click the star next to the post)
    Thanks

  • Blinking red light while in docking base

    What does this mean? I don't think it is charging because it will do this all night. Used to be just fine. I haven't been able to find any discussion around a slow blinking red light on the Shuffle...it flashes on and off at about .5 Hz
    Ideas? Tried it on a bunch of computers and even a wall charger. Is the battery done? (At only 9 months!)

    well, i sort of managed to get the shuffle to an apple authorized repair centre here in bangalore,india where they infact had the firmware updated to the latest and since the charge indicator was showing a red, the executive at the shop suggested that the unit was really low on charge and needed a minimum of 4 hours of charging. Upon charging the unit for more than 6 hours or so, the charging indicator still blinks red(when charging). i am able to play songs for the time-being but it seems the green light is totally conked out.
    does anyone know of a repair shop of ipod shuffle in india. the apple dealer was saying its best to discard the shuffle when having problems like this since its best to go in for a new shuffle. i do have another shuffle that cant be repaired:(

  • Blinking red light of DEATH

    Hi guys! 
    In advance, thanks for your help!  So here is my problem and I hope you guys can help a young gal out! I dropped my blackberry and it hasn't worked since. It wont turn on but it will for a few minutes, then will randomly shut off and blink like 2 times in a row in perfect intervals. After it turns off... it will not come back on no matter what. I have tried a different charger and even bought a new battery to put in it... But nothing has changed. Its still the same red light! PLEASE help me... Is there anything I can do that I haven't tried,  before taking it to a repair shop and spending a bunch of money for them to tell me they can't fix it?! 
    THANKS SO MUCH AGAIN! 
    ---Alex <3

    This may not work if the drop caused some physical damage, but normally for a black or white screen only, and/or the blinking red light:
    1) Make sure you have Blackberry Desktop Manager installed.
    http://na.blackberry.com/eng/services/desktop/
    2) On your PC, go to Start > Run and copy and paste the following line exactly (meaning with the quotation marks):
    "c:\program files\common files\research in motion\apploader\loader.exe" /nojvm
    3) The Application Loader Wizard will appear -- click "Next."
    4) In the "Connection:" drop-down menu, you should see "USB-PIN: UNKNOWN". Click the "Next" button.
    5) You should then see a list of applications ready to be installed for your Blackberry. Hit Next and Finish and you are well on your way to getting your Blackberry back to life. Just don't disconnect anything and let the lengthy process finish completely.
    NOTE: If you do not see a list of applications mentioned in step 5 and instead see the message "The Blackberry Desktop Software does not have Blackberry Device Software for the device that you have connected to the computer. Contact your wireless service provider or system administrator," then you must download Blackberry's Operating System for your carrier and device.
    http://www.blackberryfaq.com/index.php/BlackBerry_Operating_System_Downloads
    Just select the appropriate carrier and network type, select your Blackberry model from the list and download the latest version. Install this download and follow the above steps again and you should be on the right path.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • I have a Samsung Network Extender, model SCS-2U01, and for the past two weeks, the SYS light has gone from solid blue to a blinking red light, disconnecting me from my business calls. In reading the forums, it was mentioned that Verizon had to reset somet

    I have a Samsung Network Extender, model SCS-2U01, and for the past two weeks, the SYS light has gone from solid blue to a blinking red light, disconnecting me from my business calls. In reading the forums, it was mentioned that Verizon had to reset something on their end to fix the issue. Would you be able to confirm if something needs to be reset to fix the issue? Thank you!

    First, try the normal stuff: power cycle your modem, router, and NE allowing time for each component to stabilize before turning on the next in sequence modem > router > NE. If necessary, try resetting your modem and router. If it still doesn’t work verify it is listed in MyVerizon and then calling Verizon Wireless Customer Service at (800) 922-0204. Good luck!

  • Playbook is dead with a blinking red light

    My playbook went dead and does not come back even if I charge it for 24h.
    If I push the start bottom a blinking red light come up. I try to re-boot it pushing all bottoms and does not work.
    Also I have tried to dowload new software through my laptop but never complete it and get stuck in the middle.
    Any idea anyone???
    Thanks,

    Many others have had this problem - first thing to do is check to make sure your are using the charger that came with your PlayBook. Also check the threads at the top of forum for oft-asked questions. For your convenience here is a link that might help. Good luck.
    In the dark and need a sky map?
    Discover What's up at App World.
    Follow What's up on Facebook

  • Sir my xperia SP is not charging..when i plug the charger i just see red light

    Sir my xperia SP is not charging..when i plug the charger i just see red light

    When I connect  charger to the phone, LED shows red ligth for 10 to 15 min then display will light up and you l see a battery icon without  a flash inside it and the LED light turns off but the screen remain the same with battery icon without flash inside it. i have this problem with my xperia sp please help

  • Have a G3 pismo, works great, but when I plug in the power cord, the light won't come on to indicate its charging. It is charging, and the battery is good, its just that the light won't come on. Could it be something with the backup battery?

    I have a G3 bronze keyboard that works, with a good battery, but when the power supply is plugged in, the charging light on the back of the laptop
    will not come on. It is charging however, and have two different apple power adapters and both will charge the main battery, it's just that the light won't come on.
    Did a reset of the pmu, but no changes. The date stays current, but wondering if the backup battery could be getting weak and affecting it , or is something else going on?

    The power connector in the G3 PowerBook is a weak link.  Removed, it looks like this:
    [image from http://microdocusa.com/specials.html ]
    The connector probably hasn't failed, but the solder joints where "legs" on  the connector  attached to the logic/power board are under a lot of stress after 10 years of use. Little bumps and tugs on the power cord eventually degrade the connection. You can check for looseness easily---see if the connector feels loose when you GENTLY wiggle it with a fingertip. It should have zero play if it's still firmly attached. You can also plug in the power adaptor and see if slight movements if the plug make the light turn on. Pretty diagnostic of a loose connector.
    The date stays current,
    Make sure you are doing this check correctly. If you have an always-on internet connection, the date/time are fed froma  network time server and will always read properly unless you test with the internet connect turned off or disconnected.

  • My MacBook Pro has a faint blinking orange light on the charger but won't turn on, I've tried many different things to restart it but nothing works

    My MacBook Pro has a faint blinking orange light on the charger but won't turn on, I've tried many different things to restart it but nothing works

    The battery's probably drained and the power brick on the fritz. Unfortunately, if she won't start there's little we can do for software-based diagnosis. You'll have to take it in to a Store or Service Provider for assessment.

  • My shuffle is blinking orange and won't charge

    My ipod shuffle is blinking orange and won't charge.

    Blinking orange means "do not disconnect."  It may or may not be fully charged. 
    If you have the shuffle set to Manually manage music or Enable disk use, the light will blink orange until you eject the shuffle.  This is because, with those setting, the system has continuous access to the iPod (as a "disk"), so the iPod is technically "in use," even if it is just sitting there. 
    To eject the shuffle, there is a small eject button (it has a triangle with a line under it) next to the shuffle's name in the iTunes sidebar (under DEVICES).  Click that button to eject the shuffle.  If the battery is fully charged, the lighit should turn solid green (not blinking).  Not blinking means "OK to disconnect" it from computer.

  • Blackberry Curve 9220 Won't Switch stuck On only red light blinking RED LIGHT! HELP!

    my blackberry is stuck on red light blinking oleas help me no problem if all the data is lost i dont care i want my phone back it hase been 3 -4 weeks . light is blinking until the battery goes down and it wont charge also i have to get the battery charged by other phone plzz help mee........ 

    Hi and Welcome to the Community!
    Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
    With the battery inside, connect your BB to the wall charger
    Leave it alone for 2 hours, no matter what the LED or the display does
    Remove the battery
    Wait 15 minutes
    Insert the battery
    Wait another 2 hours, no matter what the LED or the display does
    This has been known to "kick start" some BBs.
    It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
    Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
    Obtain access to a known good and identical BB...use your battery in it and see what happens
    The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Blackberry Z10 (SLT100-2) won't startup, no blinking red light and isn't recognized by PC

    I have been using blackberry z10 which i bought from UK 1.5 years ago which was working fine so far. now, all of a sudden, my handphone's battery drained within 30 min, than started giving 4 short red flashing light within short interval. one of my friend using same model, bought from malaysia, he told me to unplug the battery and connect the device to directly wall charger. After i did that, flashing lights are gone and giving once red light each and every time i connect wall charger with my handphone. now i interchange the baterry wid charged one. it showing no lights even if i push the starting button. I already updated the latest os and using sideloader application named(mobile 1 market).
    i now live in malaysia and also i got no receipt for showing this handphone to any BB care centre.
    I already watched all the post and tried doing this steps..
    http://www.blackberryos.com/blackberry-10-os/37518-how-install-leaked-os-onto-your-blackberry-10-sma...
    but my phone got no connection to wallcharger, pc cable even any fully charged battery.
    can you guys please help me out!!!

    Hi and Welcome to the Community!
    Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
    With the battery inside, connect your BB to the wall charger
    Leave it alone for 2 hours, no matter what the LED or the display does
    Remove the battery
    Wait 15 minutes
    Insert the battery
    Wait another 2 hours, no matter what the LED or the display does
    This has been known to "kick start" some BBs. If it fails, then redo it but increase the wait time in step 4 to 2 hours, and perhaps 4-5 hours.
    It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
    Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
    Obtain access to a known good and identical BB...use your battery in it and see what happens
    The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Photosmart 7450 appears to be jammed, blinking red light

    My Photosmart 7450 had been working great until a few weeks ago. It just stopped printing. I didn't change any settings or cartridges. I've tried unplugging everything, cleaning it out, changing cartridges, test prints...
    Symptoms:
    - When I turn it on the light is green and appears to be functional (Good)
    - When I tell it to print it feeds the paper into the proper position (Good)
    - The print cartridges start moving (Good)
    - Red light comes on blinking and everything stops (Bad)
    - When I open the lid the cartridge is on the right side, and when I try and move it by hand it is stuck by a little tab below it
    Any thoughts what it might be and how I can fix it? Thanks.

    What modem do you have? Is it a pure modem.. ie no router??
    If it is a router then the Express has to be in bridge mode.
    Assuming you have a pure cable modem..
    When you change from the computer to the Airport Express, are you powering down the modem. If it has battery backup for phone you need to remove the battery as well.. it has to be off for around 20min but it can be longer or shorter than that. Restart the modem.. wait a couple of min then plug in the Express which must be in router mode so it captures the public IP.

  • Blinking Red Light s and start

    I have tried for a week now, charging for 24hours with the provided charger but it will not boot. It just blinks with 2 red lights every 5 seconds or so.
    I tried puching teh start button for 20 seconds...nothing, also tried puching all the buttons for 20 seconds...nothing.
    Help!?

    Any Help...?

Maybe you are looking for

  • SCEP on ISE 1.2 and Windows 2003 Server

    Hi there has anyone ever be able to get SCEP on ISE 1.2 working with Windows 2003 Server? I know Cisco recommends Windows 2008 Server onwards, but sometimes the server infrastructure is not yet there. Thanks in advance and best regards Dominic

  • Error Handling for SOA Server

    Hi All, I converted a java code into a webservice with the help of jdeveloper and deployed it into weblogic server, and it is working fine when I am invoking it through the SOA server. But, when I am passing some wrong input values I should suppose t

  • How not to show my full name in itune store

    when i publish the application,  how do i set it name instead of my full name

  • Cpt 3 - quiz summary page falsely triggers 100% completion

    I'm experiencing a problem - I've noticed the quiz summary page falsey triggers to the LMS that 100% of the slides are complete when they aren't. I'm using Captivate 3 and Sum Total. I have a standalone quiz that is part of a curriculum where the cur

  • Ipod nano 6th generation won't sync at all !

    hello everyone and thx for the helpers . i got macbook pro (late 2011) and ipod nano. when i'm trying to sync it with my music on my itunes , nothing happens , nothing ! i'm getting crazy from this . basically, when i plug the ipod to my mac the itun