My tablet is not on the supported device list, but meets requirements to run. how to install?

I have a supper pad 3 tablet. The android market does not recognise my tablet, but i have installed other apps directly from the developer and bypass the market. Can i download firefox as a file and install directly to my tablet?

It is not compatible. According to http://www.androidtabletspcs.com/10-LCD-Panel-Touch-Screen-1024-768-Android-2-2-Tablet-PC-B-pad103.html the device has an arm11 cpu which supports the armv6 instruction set. Firefox requires a cpu that supports armv7.

Similar Messages

A Camcorder that's not on the "Qualified Devices List.." Still work?

I everyone. I own a Sony DCR-TRV-250 Digital 8 Hanycam Camcorder and I am looking into Final Cut Express HD, but I noticed that my camcorder is not on the qualified devices list. For those of you who know about this, is there a possibility that my camcorder may still work? Your Support Is *GREATLY* appreciated! Thanks so much.

To use a camera with FCE, it needs to be DV and have a FireWire connection. Your TRV250 does both. Digital8 is a Sony thing, but under the covers it is a DV codec recording on a Digital8 cassette. There are some technical differences in the tape transport speed and how the magnetic recording is made on the tape compared to miniDV tapes, but the codec itself is DV, and the output via the FireWire connection is also DV. So, it should work with FCE, and iMovie too.
The only way to know for sure is to give it a try. Find your local Apple store and take your camera there & try it. That's the same advice we'd give anyone, regarding any camera.
Oh, and by the way, I noticed that your profile says you are running 10.0.x - for FCE-HD you need at least 10.4.6 and QT 7.0.4 - check the full specs here.

My Sigma 17-70 f2.8-4DC is on the supported lens list but not in the Profile Downloader.

My Sigma 17-70 f2.8-4DC is on the supported lens list but not in the Profile Downloader.
How can I download the profile?
Thanks very much.

The “Lens Profile Downloader” is not where you get lenses “on the list”, rather it is where you get lenses that third-parties have provided, so usually for lenses not on the list.
I see three Sigma 17-70 f/2.8 DC variations for 5 different camera manufacturers so I’d expect you should see the lens listed if you select a raw photo. There is no profile for JPGs.
Here are the profiles for Canon:
Canon (SIGMA 17-70mm F2.8-4 DC MACRO OS HSM C013) - RAW.lcp
Canon (Sigma_17-70mm_F2.8-4.5_DC_MACRO_HSM ) - RAW.lcp
Canon (Sigma_17-70mm_F2.8-4_DC_MACRO_OS_HSM ) - RAW.lcp
What is your actual situation, are you looking at a JPG that won’t have a lens profile, or is the lens profile not in the list for your camera or is it just not being found automatically when you set Lens Profile Setup to Auto.

New iPad is not on the authorised devices list

Every thing seems to be working as it should. I can download from the store etc. but, my new iPad Air is not shown on the authorised devices list in my account.
Is there something I need to do to get it recognised?
Cheers.

Same for me, Diamond White. Everything seems to work, but my new iPad Air isn't showing up in the list.
Thanks for suggestions, King_Penguin. Alas, I tried all of those except iTunes Match (don't want or need) and still no joy getting the device to appear in the list. My main PC is there along with my iPad 3.
Regards.

My 4th generation ipod doesn't come up in the itunes device list but as an icon on the desktop. How do we get music onto it?

There is a device icon on the desktop but all songs have been erased.
How do we get the songs onto the ipod if it doesn't come up in the itunes device list?

iPod appears in Windows but not in iTunes

Hello, my device is Samsung GT-S5660. I am thinking that maybe you forgot to add it to the supported devices list. Because you support Samsung Galaxy series mobile phones. Will it be available for my phone soon?

Will firefox be available for Samsung GT-S5660(Galaxy Gio)?

The GT-S5660 is an ARMv6 phone Firefox requires an ARMv7 phone. The first Galaxy in that series with an ARMv7 support is the 9000.

My iPod will not show up in the Itunes device list plus I get an error message

Hello!
My iPod will not show up in the Itunes device list plus I get an error message
" One or more devices is getting too much power from the USB wire" or sumptin like that.
I've tried this with two wires, so the problem is not there.
I reseted the iPod to factory settings but it didn't help.
Anyone??

- See:
iPod touch: Hardware troubleshooting
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- Try another USB port and computer
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

How do I only show my inbox on email and not all the support folders

How do I only show my inbox on email and not all the support folders

There is a third-party program called Attachment Tamer that will do that for you. In the Terminal, you can type this:
defaults write com.apple.mail DisableInlineAttachmentViewing -bool yes
Also note that while Attachment Tamer does some things with the encoding that makes certain email clients display the item as an attachment, what shows up at the receiver's end is solely dependent on their email client and its settings.

ATV not showing in the iTunes device list? Check your HTTP proxy config

Seems like many people are having trouble getting their ATV to show up in the iTunes Devices list. Here's my situation, and the root cause:
1. I have a small network at home consisting of one LAN with a number of computers, and a gateway router that provides DHCP, DNS and HTTP (web) proxy services
2. I found that my ATV would display in the Devices list only when the ATV and at least one Mac were isolated from the rest of my network; when I connected them back to the rest of the LAN the ATV disappeared from the Devices list (in the simplest case this isolation was a crossover cable between the Mac and ATV)
3. when connected to the whole LAN, the ATV could successfully contact the iTunes Store (trailers, etc) but would not show up in the Devices list
4. I could ping the ATV from the Mac running iTunes every time (i.e. I did not have a basic connectivity problem; e.g. "ping appletv.local." always worked)
5. I started with my ATV on v1.1, when I upgraded to 2.0 and turned on the the iTunes' "Look for remote speakers connected with AirTunes" option ATV always appeared in the speaker list (i.e. even when it wasn't in the Devices list)
I had gone through the Apple troubleshooting guides, with no change.
After a lot of elimination I discovered that my problem was with my web proxy settings: my Macs were configured to use my gateway router for HTTP, and it seems that iTunes connects back to the Apple TV via HTTP - these requests were sent to the proxy and rejected (as they were for an address on the inside LAN; this is the way my proxy was configured).
I fixed the problem by using a PAC file specifying my LAN as "DIRECT" (e.g. below). An alternative would have been to configure my proxy to allow connections from the LAN back into the LAN (but be careful about allowing access from elsewhere, e.g. the Internet).
Here's my PAC file: my LAN is in the 10.0.0.0/8 address space, domain *.home.lan. (iTunes seems to contact the AppleTV via it's IP address, e.g. http://10.0.0.169:3689/ript/fp-setup?fairPlayID=4a5...):
function FindProxyForURL(url, host)
// simple hostname
if (dnsDomainLevels(host) == 0) {return "DIRECT";}
// match Host against local domains (w/ optional :port)
var dom = /(127\.\d.d+.d+|.local.?|10.d+.d+.d+|.home.lan.?)(:d)?/;
if(dom.test(host)) { return "DIRECT"; }
// All other requests go through port 8080 of proxy
// should that fail to respond, go directly to the WWW:
return "PROXY proxy.home.lan:8080; DIRECT";
The reason the ATV was successfully appearing in the Devices list when it and a Mac were isolated from the rest of the LAN was that the Mac was unable to reach the proxy, and falling back to the 'DIRECT' connection.
Note: if you don't have basic connectivity, e.g. if ping appletv.local. doesn't work, then the above is almost certainly not your problem.
Ben
Message was edited by: af3556

Hi There,
I have the exact same issue going on that this person described in this thread, but with the EXCEPTION in my case being that, after I have plugged my device into my laptop and uplugged it (about 10 consecutive times), my iTunes FINALLY recognizes my iPod Touch.
This is extremely frustrating to have to go through this scenerio each and every single time I want to synch and charge my Touch. Is there any way to correct it, so that the device would be recognized immediately when I first plug it in? It used to work this way (prior to the v.10 update, most likely).
Thanks!

"Could Not Open the Communication Device" ???

I use a dial up connection. Everytime I try to connect to the internet, after it dials a message box pops up that says "Could Not Open the Communication Device". Has anyone else had this problem? And how do I fix it?
Please help me.

I found this in Mac Help:
If you haven't entered your network settings, open Network preferences, choose your modem port (internal or external) from the Show pop-up menu, and enter the settings provided by your ISP, such as the access phone number, your user name, and your password.
You can also use the Network Setup Assistant to help you enter network settings. Click "Assist me" in the Network pane of System Preferences and follow the onscreen instructions.
Also verify that the number you are dialing is correct.
Try this too.
Some ISPs may require a PPP connection terminal script to connect to the Internet using a modem. If it is required, contact your ISP for the terminal script
To use a PPP connection terminal script follow these steps:
In the Finder, navigate to the Library folder on your startup disk.
If the Library folder does not contain a Terminal Scripts folder, you will need to create it. Choose File menu > New Folder, and name the new folder "Terminal Scripts."
Copy the terminal script file from your ISP to the Terminal Scripts folder.
To activate the terminal script, choose Apple menu > System Preferences.
Click Network and choose your modem port (internal or external) from the Show pop-up menu.
Select the PPP tab and click the PPP Options button.
Choose your connection script from the Terminal Script pop-up.
Click OK and then click Apply Now.
If the Terminal Script pop-up menu is dimmed, then the script is not being recognized. Check that the script is valid, and it is installed in the correct location.
-Internet Wiz

Getting "Internet Connect Could not open the communication device"

I am getting a pop up showing "Internet Connect - Could not open the communication device."
Why is this? I have never got it before and after awhile my internet works just fine. I am trying to understand why it's popping up. The wireless networks I connect to are always working fine but my computer is just now giving me this pop up.
Please help. Thank you.
-Mike

you could try moving either file one at a time, don't delete them though
if moving the files and restarting does not fix the problem you can always put them back to the original location, it's just settings files
possibly you'd need to setup your network prefernces again
also, in System Preferences, click on Accounts pane, then your user name (you may need a password for that)
on the right side of the Accounts window there is "Login Items" tab, see if anything shows up in login items
as a guess, machine tries to connect by looking for your cell phone to use as a modem or something
maybe check Network preference pane, see what shows up in Bluetooth

Resume: Could not stat the resume device file After Update

Peace!
I -Syu and rebooted to this error:
resume:
Could not stat the resume device file '/dev/disk/by-label/hda1'
Please type in the full path name to try again
or press Enter to boot the system:
Figuring it must be something weird happening to the suspend procedure, I wanted to skip it and boot normally. So I pressed Enter... to no avail.
Waiting for devices to settle .... done.
Root device ' /dev/disk/by-label/hda2' doesn't exist, attempting to create it.
ERROR: Failed to parse block device name for '/dev/disk/by-label/hda2'
ERROR: Unable to create/detect root device '/dev/disk/by-label/hda2'
Dropping to a recovery shell... type 'exit to reboot
NOTE: klibc contains no 'ls' binary, use 'echo *' instead
If the device '/dev/disk/by-label/hda2' gets created while you are here,
try adding 'rootdelay=8' or higher to the kernel command-line
ramfs$
Now, I'm starting to think its not just due to the suspend procedure and maybe something more. Afterall, I did not suspend, I rebooted. I remember updating the kernel, klibc and perhaps udev.
I wanted to try adding the rootdelay thing but the grub menu wouldn't show up.
Sobs..
I really need to research on failsafe fallback procedures... some kind of ultimate undo feature.
Last edited by onguarde (2009-01-21 08:39:40)

http://bbs.archlinux.org/viewtopic.php? … 58#p484758
It seems someone else has similar problems...

I have 4 ricco md2 mini USB speakers and i can't get them to play at the same time. i have tried using the aggregate device feature but have had no luck. i can play each pair separately, but not together. what should i do?

i have 4 ricco md2 mini USB speakers and i can't get them to play at the same time. i have tried using the aggregate device feature but have had no luck. i can play each pair separately, but not together. what should i do?

i have 4 ricco md2 mini USB speakers and i can't get them to play at the same time. i have tried using the aggregate device feature but have had no luck. i can play each pair separately, but not together. what should i do?

Upgrade to Windows 10 by using my notebook as a tablet does not turn the screen

I realized that after doing my upgrade to Windows 10 by using my notebook as a tablet does not turn the screen (al realizar mi actualizacion a windows 10 mi laptop ya no gira la pantalla en modo tableta... y es 360 grados.. como lo resuelvo??? gracias!!!

i have the same problem with my envy x2 13 j002dx. tried reinstalling drivers and windows 10. the auto rotate button is there but doesnt do anything when i toggle it

Supressing the "Could not open the communication device" message

Hello,
Lately whenever I connect to the internet, an Internet Connect window pops up with the message "Could not open the communication device." The connection, however, is fine, and I have no problems accessing the internet.
I've been clicking "OK" to this message several times whenever I connect to the internet but it's become tedious and I'd like to supress it. Can anyone help me?
20" Intel Core 2 Duo iMac Mac OS X (10.4.10) I'm using a Linksys WRT54GL to connect wirelessly.

Check to see what is checked ON in Network>Show:>Network Port Configurations, and drag the one used for Internet to the top of the list at least.
I think there must be another one checked ON and above the one that actually connects... dunno for sure yet though.

My tablet is not on the supported device list, but meets requirements to run. how to install?

Similar Messages

Maybe you are looking for