My time capsule turns on and then turns off...

my time capsule turns on, then amber light is blinking and then it turns off. the whole story takes 15 sec. any suggestions? is this the end?

Ok, I'll dismount the harddrive and have a look how it behaves then. If it stays on I'll head for a power supply replacement.
This seems to be a good disassembly how-to:
http://www.youtube.com/watch?v=ATjKELezw9s
Also yours (@LaPastenague):
http://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modems /apple-time-capsule-repair
Moreover it's seems to be a known problem by apple:
http://arstechnica.com/apple/news/2010/07/apple-to-replace-time-capsules-with-do dgy-power-supplies.ars
Unfortunately the link provided doesn't work anymore:
http://support.apple.com/kb/TS3351

Similar Messages

My time capsule was working and then I added another Macbook pro. TC stopped appearing in Airport Utilities. I have tried resetting TC, I have turned if off and held reset button with pen for 10 secs. I just cannot work out what else to do?

My time capsule was working and then I added another Macbook pro. TC stopped appearing in Airport Utilities. I have tried resetting TC, I have turned if off and held reset button with pen for >10 secs. I just cannot work out what else to do? I have turned router off and on. Amber light is flashing.

The ethernet says self assigned IP 169.254.67.6
Then the ethernet is not getting an IP from the TC.. there is no connection.
I am not sure where you mean when you say the green LED should be on. Do you mean the TC?
Thanks
In order to help troubleshoot ethernet connections all routers use connectivity leds.. even APPLE.. it has one big LED on the front.. and 4 tiny leds beside each ethernet port. That light has to come on for ethernet to be active.. if you plug an ethernet cable into the port and the light doesn't come on.. then there is no connection.. either the other end isn't plugged in.. or the cable is bad.. or the ethernet port is bad.. something is wrong.
To get access to the TC you need this led to be green.. is it?
If it is green and the WAN is also green.. then I want you to unplug the WAN connection.. the blue wire in the picture.. the port slightly separated from the 3 LAN port.. computer plugged just into LAN port.. no airport turned on.. and press the reset again for 10sec until front led flashes rapidly.. then try and bring up the airport utility again.. assuming the ethernet led is green.
How old and what model is the TC?
The A number from the rubber mat will tell us the model.

Time Capsule Turns OFF on reboot and wake up

I'm using the latest versions of everything on this iMac and AirTime Capsule. For the past few weeks I noticed that when the desktop wakes up Time Machine is OFF in System Preferences or when I reboot the Mac, Time Machine turns OFF also.
Reading other posts, I started to look for a com.apple.TimeMachine preference in the Library but I could not find any reference to that file.
It's annoying because I expect my stuff to be backed up during the day while working. At night, before the Mac goes to sleep, SuperDuper does a full backup on a different drive.
If you could help resolve this issue, I would appreciate. TIA.

Thanks for your reply. That's what I've been doing to delete in Library the TimeMachine plist file. I even lock after the first reboot the SysPrefs panel of the Time Machine to ON. Then on second reboot, Time Machine reverts automatically to OFF. Same thing the next day waking up after sleep. The Mac wakes up and Time Machine is OFF again.
I am puzzled and confused as to why it does this. Time Machine has worked superbly since last July, then around the end of December it started doing this trick. I update religiously my Macs whenever Apple Software Update tells me to, so I'm running now on this iMac 10.6.6 and on the AirTimeCapsule 7.5.2.
Dazed and confused

HT3728 Time Capsule turned "off" and won't turn back "on"

My Time Capsule shut down last night--completely turned off--and won't turn back on. It felt warm, so I unplugged it overnight. I tried plugging it back in this morning and it still doesn't have power. I've also tried plugging it in somewhere else, and the hard reset as described on the Apple Support Website. But still no power. The green/amber light doesn't come on at all. Suggestions?

the power supply is cooked in its own internal oven bag..
It sounds like it is beyond warranty but if you have applecare on a Mac that will also cover the TC if it was purchased within 2years of the computer..
Otherwise a self - repair is possible or help from a repairer if you happen to live in an area.. to Apple it is a sealed unit and they will not help you.
http://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modems /apple-time-capsule-repairers
When I read your title I thought this was a playback of the thread.
https://discussions.apple.com/message/17983281?tstart=0#17983281

Time Capsule Turns Off

I am having some troubles with my time capsule. It has been working flawlessly for the last 3 months...until this weekend. Three times now, it has turned off at some point. If I unplug it and plug it back in, the front lights back up and all is good.
The switch has constant power and I did not have any problems with the network before this...
any ideas?
bk

This has just started happening to me as well.
I have a 1TB Time Capsule & over this past weekend it's turned completely off on it's own 4-5 times.
Unplugging it and replugging it boots it back up.
BK, any further news on yours?
Thanks,
-G

Mackeeper has detected a virus in the time capsule back up - it is not possible to dele - it ite the file. Do I find time capsule in finder and delete the whole computer back up, then crate a fresh back up? Is that the only solution please?

mackeeper has detected a virus in the time capsule backup, it is not possible to delete the infected file. Do I mount time capsule in finder and then consign to junk the whole computer backup then create a fresh backup? Is that the only solution please.

Follow these instructions to uninstall MacKeeper. They have been tested with the most recent version of MacKeeper. Earlier versions than the one released in 2012 require more extensive work to uninstall all its components. Never install such junk on a Mac.
If you actually used MacKeeper to alter your system, e.g. "remove excess binaries" or such, you will need to reinstall OS X as well as all your additional software. Uninstalling MacKeeper is insufficient to reverse the corruption it is capable of - once again, that is if you used it.
If you merely installed MacKeeper but did not use it to perform any particular action, the following instructions will suffice.
If you used MacKeeper to encrypt any files or folders, use MacKeeper to un-encrypt them first.
Quit the MacKeeper app if it is running.
Open your Applications folder: Using the Finder's Go menu, select Applications.
Drag the MacKeeper icon from your Applications folder (not the Dock) to the Trash.
You will be asked to authenticate (twice):
You do not need to provide a reason for uninstalling it:
Just click the Uninstall MacKeeper button. You will be asked to authenticate again.
After it uninstalls you may empty the Trash and restart your Mac. All that will remain is an inert log file that does nothing but occupy space on your hard disk.
May I suggest that you review the following setting in System Preferences?
Although you may easily override that setting, it will serve to protect you from inadvertently installing garbage. The overwhelming majority of Macs I come across have the MacKeeper installer file already present in their Downloads folder, often multiple copies of it. The downloaded file itself can do nothing until it is opened and installed, and the above setting (known as Gatekeeper - not to be confused with MacKeeper) will prevent that from occurring.

Time capsule is slow and inconsistent

It seems that the wifi is much slower than my old airport extreme, and inconsistent in terms of connectibility and strength. Any hints? I've been at this for two days.

All,
Maybe trying some of these suggestions will help?
*_Slow Time Capsule Transfer Speeds_*
*Initial Backup Best Over Ethernet*
It is recommended that you perform the initial full backup via ethernet, then all subsequent backups via wireless.
*Transmit Power & Wide Channels*
If you are using the 802.11n only (5 GHz) radio mode, you can also select to use wide channels, which provide higher data throughput in your network.
Launch Airport Utility
Select your Time Capsule on the left.
Click “Manual Setup”.
Select “Airport” in the toolbar.
Click the “Wireless” tab.
Click “Wireless Options...” at the bottom of the window.
Adjust the “Transmit Power” to 100%.
Put a check mark in the box labeled “Use Wide Channels”.
Click “Done”.
Click “Update” in the lower right hand corner.
Wait for the Time Capsule to restart and then see if your network speeds improve.
*Anti-Virus Software*
Are you running anti-virus software. Disable it and see if network speeds improve. The discussion boards are filled with users who are experiencing degraded network speeds due to their anti-virus software.
One poster observed: “I had the exact same problem 5mins ago, it had taken 2 hours to back up 2GB, I realized I installed Sophos anti virus a couple of days ago. When I turned that off my back up is speeding through.”
Another contributor stated, “I am doing the first backup to my time capsule, about 71 Gb, It seems to be going about 1 Gb per hour. is this seem OK? I tried the ethernet connection and the speed was about the same. It has been going all night and after 12 hours it is at only 12 Gb of 71….I found the problem, I uninstalled Norton and the problem went away. It backed up in about 3 or 4 hours”
*Wireless Security Issue*
Some who have experienced degraded network speeds have isolated the problem to their wireless security setup. Try this:
Launch Airport Utility
Select your Time Capsule on the left.
Click “Manual Setup”.
Select “Airport” in the toolbar.
Click the “Wireless” tab.
Change “Wireless Security” to “None”.
Click “Update” in the lower right hand corner.
Wait for the Time Capsule to restart and then see if your network speeds improve.
Granted, this is far from desirable. But it does help to isolate the problem in you instance. Maybe simply resetting the security with a new password will help?
Let us know if any of these procedures helped.
Cheers!

Hay. i change the screen LCD in IPAD 2 3G but i don't know what happen. She was working and every thing it's ok. One time i turn off the ipad and turn on more time, i don't see good in LCD the brightness is to low and i can see any thing

Hay. i change the screen LCD in IPAD 2 3G but i don't know what happen. She was working and every thing it's ok. One time i turn off the ipad and turn on more time, i don't see good in LCD the brightness is to low and i can see any thing!! and i want to know why is happen

Assuming you mean that you performed the repair yourself, it would seem that you either obtained a defective screen or you did some sort of damage when you replaced the screen. You can try asking for assistance on ifixit.com, a site dedicate to those attempting their own repairs, or you can take the iPad to a shop and pay them to try to correct the problem for you. Apple will no longer touch your iPad now that you've attempted your own repairs.
Regards.

How to setup apple time capsule with FIOSinternet and VZ router?)

Hello,
I have Apple time capsule and the VZ Router MI424WR. I current set up:
1. VZ router - wireless off, the rest is standard
2. Time capsule: Wireless on in Bridge mode
Result: Internet works but the wireless network is very in-stable. Airtunes is nearly not usable.
I searched in the Internet and there was several comments that is is not a good combination. Therefore it is recommended to convert the VZ router in a modem mode and use only the Time capsule as the router. I tried this several times I do not get it to work. I followed this procedure (http://data.agaric.com/node/2160) but then I need the PPPoE Account number and password. But there do I get this? The Verizon support was not really helpful.
Please, is there a good and complete description to solve that issue?
Thanks in advance
Moebius

Go back to your first setup ...
Verizon router with wireless turned off
Apple Time Casule with wireless turned on
Method 1:
With the Time Capsule in "Bridge Mode", if I remember correctly, you should connect the WAN port to one of the open ports on the Verizon router (I believe bridge mode also turns off the DHCP server on the Time Capsule, if not, find that and turn if off as well).   Change the addressing mode for the Time Capsule to "static" and assign it an address on the LAN which is not in use (choose something you know is out of the way but on the LAN -- I suggest 192.168.1.180 to start -- you can change it once you get everything working).
If it doesn't work this way for you, move the cable from the WAN port on the Time Capsule to Port 1 and try again.
Method 2:
This results in a router behind a router setup, but unless you have devices connected directly to the Verizon router, it shouldn't be a problem.
With the Time Capsule disconnected from the Verizon router, turn on "Connection Sharing" (not bridge mode) and make sure DHCP is enabled on the Time Capsule. You need to change the address range being used by the Time Capsule (which I think defaults to 192.168.1.x to another network -- I suggest, 192.168.2.x with a netmask of 255.255.255.0 and give the router an address of 192.168.2.1 on the LAN side. Now, connection the WAN port to one of the Verizon router LAN ports. If you had anything connected to the Verizon LAN ports, move those over to the LAN ports on the Time Capsule and reboot them.
Method 3:
This is the least desirable of the scenarios because it relies on Verizon's crappy radio in their router (the Time Capsule has a much better radio and support 802.11n as well as b and g) whereas Verizon's only support b/g.    Go back to the configuration for Method 1, but also turn OFF wireless on the Time Capsule and turn on wireless on the Verizon router.   Try both bridge scenarios described -- using the WAN port first and if that didn't work, then moving the connection to port 1.
There is no scenario where you can place the Verizon router behind the Time Capsule -- since I believe Verizon is using all MoCA connections for the WAN side of their connection (you'd have to get Verizon to convert you to ethernet WAN and then they would not support you most likely for any STB issues with your FiOS if the Time Capsule was between the ONT and their router ... so don't even bother wasting time there ... more headaches than it would be worth.
If you're still not sure exactly what each configuration screen on the time capsule should say, post some screen snaps (or the configuration settings/choices which you are unsure about and someone will likely know the answer here).

Dual Band Network: Time Capsule (N only) and Linksys (B/G) Works *Long*

Ok, so this was more tedious than I thought it would be, but things actually seem to be working at this point.
Goal: Create a Dual Band network with Time Capsule (N only) and a Linksys WRTSL54GS (B/G)
Time Capsule: 1000BaseT wired, and 802.11N 5Ghz only wireless
Linksys: 100BaseT wired, and 802.11G 2.4Ghz wireless
Airport Utility 5.3.1
Time Capsule v. 7.3
I set Time Capsule up first, following the step by step directions for "Create a wireless network"
802.11N only, 5Ghz
WPA2 Personal
DHCP 192.168.1.1 (kinda important)
This worked fine-tested on a C2D iMac, both thru ethernet and wirelessly thru N. Time Machine backed up fine.
Now the tricky part, configuring the Linksys.( I just want to mention I had to reset this thing completely about 10 times to get it to work, using a miniscrewdriver)
Starting with a freshly reset Linksys, I connected from my MacBook ethernet port to one of the Linksys ethernet ports (Not the WAN)
I disabled Airport
I logged in to 192.168.1.1 using blank for login, admin for password (default for Linksys)
I did the following:
1) Confirmed Internet Connection Type was "Automatic Configuration-DHCP"
2) Changed Network Setup to "DHCP Server-DISABLED"
3) Turned off the Firewall settings in Security (not sure if this is necessary)
4) Changed the Operating Mode from "GATEWAY" to "ROUTER"
5)Changed the SSID to "LinksysG_ONLY" or something like that
After each one of these steps, I had to save the configuration, thru the Linksys browser interface-which blows.
6) Finally, I changed the Local IP Address of the Linksys from 192.168.1.1 to 10.0.1.251 (thanks to Henry B. for that)
7) And....I no longer had access to the Linksys at all! This stumped me for a while, until...
8) I checked my Ethernet settings (in System Preferences/Network): 192.168.1.1 was set as default router address. But my Router (at least for configuration purposes) was now 10.0.1.251, so it could no longer find it.
9) So I added a new Ethernet port (using the "+" sign), called it Ethernet-Linksys. Set it to Manual. Put in an IP of 10.0.1.250, and a Router IP of 10.0.1.251.
10) I got access to the Linksys setup page again! (Note: I'm sure there is an easier way to do this, but this is how I got mine to work )
11) I set up WPA security again, set it to an unused channel (2 in my case), mixed b/g network.
12) Finally, I moved the ethernet cable from my MacBook directly to one of the ethernet ports on the Time Capsule. I did NOT hook up the other end to the WAN on the Linksys (which for some reason I had done 100 times before) I left it in one of the 4 ethernet ports on the Linksys. Repeat, the WAN (ethernet) port remains empty.
13) I then turned Airport back on the MacBook, connected to "LinksysG_ONLY", and...I was online. And everything seems to work.

Hi kjk et al,
I've been searching the boards for something like what you have described in such nice detail. Before Time Capsule, I used a Netgear g router connected to the cable modem and an older Apple base station connected to the Netgear as a bridge. I removed the Netgear and set up my Time Capsule as the primary. The newer computers in my network can access the Time Capsule, but the old Dell with a 802.11g wireless card cannot. I don't remember seeing where I could access TC to change a setting of "N only" or b/g, but I am guessing that it is running N.
I tried to follow the steps you used for Linksys. The pre-step 1 thing, resetting it "10 times to get it to work" - how do you know when it is really reset? With Netgear plugged into electricity, I stuck a paper clip into the hole labeled on the diagram as "restore factory settings" and watched the color of the IO icon change from green to amber to green. I did it again for good measure.
I plugged ethernet from PowerBook G4 into Netgear not-WAN ethernet ports (like your MacBook to Linksys). I disabled Airport. Using Safari, I logged into 192.168.0.1 and got to the Netgear SmartWizard configuration assistant. It says, "No Internet Connection Detected. Please check the connections to the Internet WAN port and cable/DSL modem" - so I looked at your instructions but see no mention of connecting the router to the modem.
Trying to follow your numbered steps...
1. In SysPrefs: Network, Location showed Automatic, Configure showed Using DHCP.
2. I don't see an option in Network to "DHCP Server-DISABLED", but I can choose Configure: OFF. I clicked Apply but browser still gives same message.
I don't know how to continue the steps.

Why is it that every time I turn off my wifi on my phone my 3G dosen't work? Help :(

So every time I turn off my wifi from my iPhone 5c at home My 3 G Doesn't Want To Work? And a 1x keeps popping out?

Could be cause I just got my phone like 2 days ago. Lol and sometimes it has a mind of its own. Like when I'm trying to text it starts to push random letters and it will go home and then go in to my contacts and then a app with out me pressing anything. Like if it was a glitch or something?

How do I stop Firefox reverting to standard settings every time I turn off my PC?

I set up my preferred icons history, print, home etc in the places I like them yet every time I turn off my PC the next day they are back to the standard set up & I have to do them all again, more than a little bit irritating as it has never been a problem before & only started happening when I upgraded to 33.1
Things like this seem to happen every time there is an upgrade, it is getting to the point where after years of using Firefox I am seriously considering looking around for a new default browser.
As if to illustrate my point when I just restarted Firefox after installing the troubleshooter add-on all my custom icon settings are gone AGAIN.

Your preferences not saved.
Create a new profile as a test to check if your current profile is causing the problems. <br>
See '''Creating a profile''':
*https://support.mozilla.org/kb/profile-manager-create-and-remove-firefox-profiles
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues
If the new profile works then you can transfer files from a previously used profile to the new profile, but be cautious not to copy corrupted files to avoid carrying over the problem <br>
'''Profile Backup and Restore'''
*http://kb.mozillazine.org/Profile_backup
*https://support.mozilla.org/en-US/kb/back-and-restore-information-firefox-profiles
*http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

My Ipod is messed up. Every time i click the top button it just flashes the apple sign for like 5 seconds and then goes off and just continues to do that. help?

My Ipod is messed up. Every time i click the top button it just flashes the apple sign for like 5 seconds and then goes off and just continues to do that.Can someone please help?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My iphone 4 locked up for several hours. i then tried to reset by holding down the home button and power button at the same time for 10 seconds and then the home button for 10 seconds. it is now completely black. what do i do? couldnt restore it in iTunes

My iphone 4 locked up for several hours. i then tried to reset by holding down the home button and power button at the same time for 10 seconds and then the home button for 10 seconds. it is now completely black. what do i do? couldnt restore it in iTunes. Has anyone had this problem? Help!

Same thing happened to me today. I wasn't even using the phone for the past 6 hours and suddenly I can't connect to the internet, none of my internet apps would work - nothing. I tried to call AT&T from the iphone and it locked up - couldn't turn it off, change to the home screen - nada - brick.
Did the Home/Power button thing and that worked but this I've only had this phone for about 4 weeks and it's locked up more times than my 3GS did the whole two years I had it! Ridiculous

I just did an Time Capsule firmware update and now my Time Capsule is dead. What happened?

I just did a Time Capsule firmware update and now my Time Capsule is dead. What happened?

tresbaileys wrote:
it may be important to note that when I put my ear to the box I can still hear the HD spinning (although no lights are lit and it doesn't show in the airport utility). Ideas??
That is very bad.. how old is it??
The Gen4 TC can die this way.. it is not usual but it happens.
Leave it for several hours to cool off. Do a factory reset immediately when you try to restart it.
The Factory Reset.
Power down the TC.
Hold in reset. and keep holding it in. Be Gentle! It is a tiny surface mount switch with a plastic lever.. Attempting to push it out the other side of the TC will not make the switch turn on better.
(I fix TC and have several reset levers bent over and jammed or broken off).
Power on the TC.. remember with the reset held in.. this needs three arms.. a friend or power switch you can get to with your feet..
Keep holding in reset for about 10sec until the front LED flashes rapidly.
Release reset and wait .. the boot will be slow as it deletes previous setting.. only from router side and pulls out the factory defaults. No files are deleted on the hard disk.. but the name of the TC may change.
Tell me exactly what the LEDs do throughout this process.
Both the main one at the front and the LED on the ethernet ports which should all flash during bootup.
If it is less than a year.. of course Apple will replace under warranty.. 2 years in some places.. Europe .. places with stronger consumer laws. If you have applecare on a computer it should still cover the TC.
I kind of doubt you are going to get this going again... but we can try.

My time capsule turns on and then turns off...

Similar Messages

Maybe you are looking for