My USB webcam stopped working after I upgraded to OS X 10.6.8

When I installed the upgrade to OS X 10.6.8 my USB webcam stopped working. 
Any idea how to get it back.

Upgraded from what to 10.6.8?
Did it work before?
What camera?

Similar Messages

  • USB scanner stopped working after PC upgrade

    I have HP Officejet 4500 all in one printer. It has both USB and ethernet connections.
    This week I have upgraded all PC components (so everything is new) except SSD drive so that I was able to continue where I stopped working.
    However, my USB connection with printer stopped working.
    First of all, I need to say, that I had to make scanner working over ethernet, so now my printer/scanner works without USB, but:
    1. what may be the reason to stop USB connection working?
    scanimage -L has usually expected output:
    scanimage -L
    device `hpaio:/usb/Officejet_4500_G510g-m?serial=CN141F219005CQ' is a Hewlett-Packard Officejet_4500_G510g-m all-in-one
    but sometimes:
    scanimage -L
    and sometimes:
    scanimage -L
    device `hpaio:/usb/Officejet_4500_G510g-m?serial=0' is a Hewlett-Packard Officejet_4500_G510g-m all-in-one
    When I try to scan over USB:
    scanimage --format=tiff > test.tiff
    scanimage: open of device hpaio:/usb/Officejet_4500_G510g-m?serial=CN141F219005CQ failed: Invalid argument
    sometimes it stucks and sometimes:
    scanimage --format=tiff > test.tiff
    scanimage: open of device hpaio:/usb/Officejet_4500_G510g-m?serial=0 failed: Invalid argument
    I have tried all steps on https://wiki.archlinux.org/index.php/Scanner site. I remind, that on the old PC it was working correctly. The problem appeared after upgrade.
    2. The output of lsusb is:
    Bus 001 Device 005: ID 03f0:2d12 Hewlett-Packard
    When I try to connect to front USB 2.0 slot I get the following messages:
    dmesg | tail
    [ 832.202201] usb 1-8: hub failed to enable device, error -22
    [ 832.362456] usb 1-8: new high-speed USB device number 8 using xhci_hcd
    [ 832.362542] usb 1-8: Device not responding to setup address.
    [ 832.566151] usb 1-8: Device not responding to setup address.
    [ 832.769690] usb 1-8: device not accepting address 8, error -71
    [ 832.929954] usb 1-8: new high-speed USB device number 9 using xhci_hcd
    [ 832.930042] usb 1-8: Device not responding to setup address.
    [ 833.133630] usb 1-8: Device not responding to setup address.
    [ 833.337186] usb 1-8: device not accepting address 9, error -71
    [ 833.337231] usb usb1-port8: unable to enumerate USB device
    and no HP printer appears with lsusb.
    When I connect it to the front USB 3.0 printer is recognised:
    dmesg | tail
    [ 832.769690] usb 1-8: device not accepting address 8, error -71
    [ 832.929954] usb 1-8: new high-speed USB device number 9 using xhci_hcd
    [ 832.930042] usb 1-8: Device not responding to setup address.
    [ 833.133630] usb 1-8: Device not responding to setup address.
    [ 833.337186] usb 1-8: device not accepting address 9, error -71
    [ 833.337231] usb usb1-port8: unable to enumerate USB device
    [ 918.254638] usb 1-12: new high-speed USB device number 10 using xhci_hcd
    [ 918.429771] usblp 1-12:1.1: usblp1: USB Bidirectional printer dev 10 if 1 alt 0 proto 2 vid 0x03F0 pid 0x2D12
    [ 919.469924] usblp1: removed
    [ 919.470610] usblp 1-12:1.1: usblp1: USB Bidirectional printer dev 10 if 1 alt 0 proto 2 vid 0x03F0 pid 0x2D12
    Bus 001 Device 010: ID 03f0:2d12 Hewlett-Packard
    I don't have any such problem with rear USB.
    All other USB devices work with front USBs. (wireless mouse, USB external HDD, USB CD/DVD, bluetooth dongle).
    Can anybody explain me these issues please?
    Thanks a lot.

    This is the full output of lsusb -v :
    Bus 004 Device 002: ID 8087:8001 Intel Corp.
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 1 Single TT
    bMaxPacketSize0 64
    idVendor 0x8087 Intel Corp.
    idProduct 0x8001
    bcdDevice 0.00
    iManufacturer 0
    iProduct 0
    iSerial 0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 25
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xe0
    Self Powered
    Remote Wakeup
    MaxPower 0mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 9 Hub
    bInterfaceSubClass 0
    bInterfaceProtocol 0 Full speed (or root) hub
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0002 1x 2 bytes
    bInterval 12
    Hub Descriptor:
    bLength 11
    bDescriptorType 41
    nNbrPorts 8
    wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
    bPwrOn2PwrGood 0 * 2 milli seconds
    bHubContrCurrent 0 milli Ampere
    DeviceRemovable 0x00 0x00
    PortPwrCtrlMask 0xff 0xff
    Hub Port Status:
    Port 1: 0000.0100 power
    Port 2: 0000.0100 power
    Port 3: 0000.0100 power
    Port 4: 0000.0100 power
    Port 5: 0000.0100 power
    Port 6: 0000.0100 power
    Port 7: 0000.0100 power
    Port 8: 0000.0100 power
    Device Qualifier (for other device speed):
    bLength 10
    bDescriptorType 6
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 0 Full speed (or root) hub
    bMaxPacketSize0 64
    bNumConfigurations 1
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 0 Full speed (or root) hub
    bMaxPacketSize0 64
    idVendor 0x1d6b Linux Foundation
    idProduct 0x0002 2.0 root hub
    bcdDevice 3.17
    iManufacturer 3 Linux 3.17.6-1-ARCH ehci_hcd
    iProduct 2 EHCI Host Controller
    iSerial 1 0000:00:1d.0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 25
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xe0
    Self Powered
    Remote Wakeup
    MaxPower 0mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 9 Hub
    bInterfaceSubClass 0
    bInterfaceProtocol 0 Full speed (or root) hub
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0004 1x 4 bytes
    bInterval 12
    Hub Descriptor:
    bLength 9
    bDescriptorType 41
    nNbrPorts 2
    wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
    bPwrOn2PwrGood 10 * 2 milli seconds
    bHubContrCurrent 0 milli Ampere
    DeviceRemovable 0x02
    PortPwrCtrlMask 0xff
    Hub Port Status:
    Port 1: 0000.0507 highspeed power suspend enable connect
    Port 2: 0000.0100 power
    can't get device qualifier: Resource temporarily unavailable
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 003 Device 002: ID 8087:8009 Intel Corp.
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 1 Single TT
    bMaxPacketSize0 64
    idVendor 0x8087 Intel Corp.
    idProduct 0x8009
    bcdDevice 0.00
    iManufacturer 0
    iProduct 0
    iSerial 0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 25
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xe0
    Self Powered
    Remote Wakeup
    MaxPower 0mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 9 Hub
    bInterfaceSubClass 0
    bInterfaceProtocol 0 Full speed (or root) hub
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0001 1x 1 bytes
    bInterval 12
    Hub Descriptor:
    bLength 9
    bDescriptorType 41
    nNbrPorts 6
    wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
    bPwrOn2PwrGood 0 * 2 milli seconds
    bHubContrCurrent 0 milli Ampere
    DeviceRemovable 0x00
    PortPwrCtrlMask 0xff
    Hub Port Status:
    Port 1: 0000.0100 power
    Port 2: 0000.0100 power
    Port 3: 0000.0100 power
    Port 4: 0000.0100 power
    Port 5: 0000.0100 power
    Port 6: 0000.0100 power
    Device Qualifier (for other device speed):
    bLength 10
    bDescriptorType 6
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 0 Full speed (or root) hub
    bMaxPacketSize0 64
    bNumConfigurations 1
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 0 Full speed (or root) hub
    bMaxPacketSize0 64
    idVendor 0x1d6b Linux Foundation
    idProduct 0x0002 2.0 root hub
    bcdDevice 3.17
    iManufacturer 3 Linux 3.17.6-1-ARCH ehci_hcd
    iProduct 2 EHCI Host Controller
    iSerial 1 0000:00:1a.0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 25
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xe0
    Self Powered
    Remote Wakeup
    MaxPower 0mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 9 Hub
    bInterfaceSubClass 0
    bInterfaceProtocol 0 Full speed (or root) hub
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0004 1x 4 bytes
    bInterval 12
    Hub Descriptor:
    bLength 9
    bDescriptorType 41
    nNbrPorts 2
    wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
    bPwrOn2PwrGood 10 * 2 milli seconds
    bHubContrCurrent 0 milli Ampere
    DeviceRemovable 0x02
    PortPwrCtrlMask 0xff
    Hub Port Status:
    Port 1: 0000.0507 highspeed power suspend enable connect
    Port 2: 0000.0100 power
    can't get device qualifier: Resource temporarily unavailable
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 3.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 3
    bMaxPacketSize0 9
    idVendor 0x1d6b Linux Foundation
    idProduct 0x0003 3.0 root hub
    bcdDevice 3.17
    iManufacturer 3 Linux 3.17.6-1-ARCH xhci_hcd
    iProduct 2 xHCI Host Controller
    iSerial 1 0000:00:14.0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 31
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xe0
    Self Powered
    Remote Wakeup
    MaxPower 0mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 9 Hub
    bInterfaceSubClass 0
    bInterfaceProtocol 0 Full speed (or root) hub
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0004 1x 4 bytes
    bInterval 12
    bMaxBurst 0
    Hub Descriptor:
    bLength 12
    bDescriptorType 42
    nNbrPorts 6
    wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
    bPwrOn2PwrGood 10 * 2 milli seconds
    bHubContrCurrent 0 milli Ampere
    bHubDecLat 0.0 micro seconds
    wHubDelay 0 nano seconds
    DeviceRemovable 0x00
    Hub Port Status:
    Port 1: 0000.02a0 5Gbps power Rx.Detect
    Port 2: 0000.02a0 5Gbps power Rx.Detect
    Port 3: 0000.02a0 5Gbps power Rx.Detect
    Port 4: 0000.02a0 5Gbps power Rx.Detect
    Port 5: 0000.02a0 5Gbps power Rx.Detect
    Port 6: 0000.02a0 5Gbps power Rx.Detect
    Binary Object Store Descriptor:
    bLength 5
    bDescriptorType 15
    wTotalLength 15
    bNumDeviceCaps 1
    SuperSpeed USB Device Capability:
    bLength 10
    bDescriptorType 16
    bDevCapabilityType 3
    bmAttributes 0x02
    Latency Tolerance Messages (LTM) Supported
    wSpeedsSupported 0x0008
    Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport 3
    Lowest fully-functional device speed is SuperSpeed (5Gbps)
    bU1DevExitLat 10 micro seconds
    bU2DevExitLat 512 micro seconds
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 001 Device 004: ID 040b:2011 Weltrend Semiconductor
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 1.10
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 8
    idVendor 0x040b Weltrend Semiconductor
    idProduct 0x2011
    bcdDevice 2.00
    iManufacturer 0
    iProduct 1 GiGa HiD
    iSerial 0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 34
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xa0
    (Bus Powered)
    Remote Wakeup
    MaxPower 100mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 3 Human Interface Device
    bInterfaceSubClass 1 Boot Interface Subclass
    bInterfaceProtocol 2 Mouse
    iInterface 0
    HID Device Descriptor:
    bLength 9
    bDescriptorType 33
    bcdHID 1.10
    bCountryCode 0 Not supported
    bNumDescriptors 1
    bDescriptorType 34 Report
    wDescriptorLength 105
    Report Descriptors:
    ** UNAVAILABLE **
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0008 1x 8 bytes
    bInterval 10
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0000
    (Bus Powered)
    Bus 001 Device 003: ID 0e8d:1806 MediaTek Inc. Samsung SE-208 Slim Portable DVD Writer
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    idVendor 0x0e8d MediaTek Inc.
    idProduct 0x1806 Samsung SE-208 Slim Portable DVD Writer
    bcdDevice 0.00
    iManufacturer 1 MediaTek Inc
    iProduct 2 MT1887
    iSerial 3 S16B6YMF7009NZ
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 32
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 4 Default
    bmAttributes 0xa0
    (Bus Powered)
    Remote Wakeup
    MaxPower 500mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 2
    bInterfaceClass 8 Mass Storage
    bInterfaceSubClass 2 SFF-8020i, MMC-2 (ATAPI)
    bInterfaceProtocol 80
    iInterface 5 6238--Storage
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x02 EP 2 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Device Qualifier (for other device speed):
    bLength 10
    bDescriptorType 6
    bcdUSB 2.00
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    bNumConfigurations 1
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0000
    (Bus Powered)
    Bus 001 Device 002: ID 1058:1100 Western Digital Technologies, Inc. My Book Essential Edition 2.0 (WDH1U)
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    idVendor 0x1058 Western Digital Technologies, Inc.
    idProduct 0x1100 My Book Essential Edition 2.0 (WDH1U)
    bcdDevice 1.65
    iManufacturer 1 Western Digital
    iProduct 2 My Book
    iSerial 3 57442D574341554630313130313431
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 32
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xc0
    Self Powered
    MaxPower 2mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 2
    bInterfaceClass 8 Mass Storage
    bInterfaceSubClass 6 SCSI
    bInterfaceProtocol 80 Bulk-Only
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x02 EP 2 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Device Qualifier (for other device speed):
    bLength 10
    bDescriptorType 6
    bcdUSB 2.00
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    bNumConfigurations 1
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 001 Device 012: ID 03f0:2d12 Hewlett-Packard
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    idVendor 0x03f0 Hewlett-Packard
    idProduct 0x2d12
    bcdDevice 1.00
    iManufacturer 1 HP
    iProduct 2 Officejet 4500 G510g-m
    iSerial 3 CN141F219005CQ
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 108
    bNumInterfaces 3
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xc0
    Self Powered
    MaxPower 2mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 3
    bInterfaceClass 255 Vendor Specific Class
    bInterfaceSubClass 204
    bInterfaceProtocol 0
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x01 EP 1 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x82 EP 2 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x83 EP 3 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0040 1x 64 bytes
    bInterval 7
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 1
    bAlternateSetting 0
    bNumEndpoints 2
    bInterfaceClass 7 Printer
    bInterfaceSubClass 1 Printer
    bInterfaceProtocol 2 Bidirectional
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x08 EP 8 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x89 EP 9 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 2
    bAlternateSetting 0
    bNumEndpoints 2
    bInterfaceClass 255 Vendor Specific Class
    bInterfaceSubClass 255 Vendor Specific Subclass
    bInterfaceProtocol 255 Vendor Specific Protocol
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x06 EP 6 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x87 EP 7 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 2
    bAlternateSetting 1
    bNumEndpoints 2
    bInterfaceClass 255 Vendor Specific Class
    bInterfaceSubClass 212
    bInterfaceProtocol 0
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x06 EP 6 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x87 EP 7 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Device Qualifier (for other device speed):
    bLength 10
    bDescriptorType 6
    bcdUSB 2.00
    bDeviceClass 0
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    bNumConfigurations 1
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 9 Hub
    bDeviceSubClass 0
    bDeviceProtocol 1 Single TT
    bMaxPacketSize0 64
    idVendor 0x1d6b Linux Foundation
    idProduct 0x0002 2.0 root hub
    bcdDevice 3.17
    iManufacturer 3 Linux 3.17.6-1-ARCH xhci_hcd
    iProduct 2 xHCI Host Controller
    iSerial 1 0000:00:14.0
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 25
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0xe0
    Self Powered
    Remote Wakeup
    MaxPower 0mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 1
    bInterfaceClass 9 Hub
    bInterfaceSubClass 0
    bInterfaceProtocol 0 Full speed (or root) hub
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0004 1x 4 bytes
    bInterval 12
    Hub Descriptor:
    bLength 11
    bDescriptorType 41
    nNbrPorts 14
    wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
    TT think time 8 FS bits
    bPwrOn2PwrGood 10 * 2 milli seconds
    bHubContrCurrent 0 milli Ampere
    DeviceRemovable 0x00 0x00
    PortPwrCtrlMask 0xff 0xff
    Hub Port Status:
    Port 1: 0000.0503 highspeed power enable connect
    Port 2: 0000.0100 power
    Port 3: 0000.0503 highspeed power enable connect
    Port 4: 0000.0503 highspeed power enable connect
    Port 5: 0000.0100 power
    Port 6: 0000.0100 power
    Port 7: 0000.0303 lowspeed power enable connect
    Port 8: 0000.0100 power
    Port 9: 0000.0100 power
    Port 10: 0000.0100 power
    Port 11: 0000.0100 power
    Port 12: 0000.0100 power
    Port 13: 0000.0100 power
    Port 14: 0000.0100 power
    can't get device qualifier: Resource temporarily unavailable
    can't get debug descriptor: Resource temporarily unavailable
    Device Status: 0x0001
    Self Powered
    The cable is quite long. It has about 1,5m. Unfortunatelly, I don't have another cable to test it. Strange is, it was working before....

  • Satellite P200 - Webcam stopped working after Vista upgrade

    Since upgrading Vista Home Premium to Vista Ultimate the integrated webcam has not worked. I've re-installed the Camera software whch proceeds to the point of updating driver software. The process fails with the messages "Windows encountered a problem install the driver software for your device". "Windows found driver software for your device but encountered an error while attempting to install it. Chicony USB 2.0 Camera". "The driver installation file for this device is missing a necessary entry. This may be because the INF was written for Windows 95 or later. Contact your hardware vendor".
    The Toshiba download site does not contain drivers for this device. only the Camera Assistant Software. The Chicony Electronics site contains some drivers for cameras, but doesn't describe the cameras and refers to model numbers which don't tally with the Toshiba references. I tried the latest model, but the driver installation completed with no termination messages and the camera still didn't work. Running the installation a second time recognised that something had been installed and proceeded to remove it, again no completion messages. A real class act!
    Can anyone suggest where I might find a solution?

    Hi Syntax,
    I did originally assume that the CAS software included the necessary drivers and have already done pretty much what you suggest about 3 times already. Still I have tried again exactly as you suggest.
    Removed the "Unknown Device" from Device Manager.
    Uninstalled the CAS software.
    Restarted.
    Ran CCleaner.
    Restarted.
    When Vista prompted to install driver for the new hardware, I declined.
    Ran the ToshibaCAS.exe program, which completed successfully.
    On attempting to use the software, the message "Switch on Camera" is displayed.
    Device Manager shows hardware as "Unknown Device".
    Properties show "The drivers for this device are not installed. (Code 28)"
    Re-installing drivers from Device Manager repeats the problem stated in original question.
    Thanks,
    Alan

  • My camera connection kit stopped working after I upgraded to  ios5

    My camera connection kit stopped working after I upgraded to ios5. If I plug it in to my iphone I get a message saying it is not recognised, but when I plug it into the ipad it does nothing at all. I've tried resetting it, but that makes no difference.
    I have an ipad 1 which I bought because it had lots of storage. I'm going on holiday soon, and I want to be able to upload my holiday photos to my ipad while I'm away.
    Any suggestions?

    Actually this sounds the same problem I have on my iPad2.
    I use a cheap copy of the CCK which I got off eBay.
    It worked great when fitted with a 16gb SD card, but since I upgraded to 5.01 it has stopped working.
    Sorry, no solution at this point but it worked on 4.3.3 but not on 5.01.
    I'll keep on looking, was considering a proper CCK thinking the cheapmversion may be drawing too much current, but it sounds like that might not work either.

  • SugarCRM stops working after Leopard upgrade

    My local copy of SugarCRM CE 4.5.1 was working in Tiger before I upgraded to Leopard last week.
    After the upgrade, SugarCRM complains with the following message:
    =====
    Warning: mysqli_connect() \[function.mysqli-connect\]: (HY000/2005): Unknown MySQL server host 'localhost:/tmp/mysql.sock' (1) in /Users/orest/Sites/ruby/ruby.sugarcrm_from-backup-20080813/include/database/Mys qliManager.php on line 419
    Warning: mysqli_close() expects parameter 1 to be mysqli, boolean given in /Users/orest/Sites/ruby/ruby.sugarcrm_from-backup-20080813/include/database/Mys qliManager.php on line 444
    Could not connect to server localhost:/tmp/mysql.sock as root.Unknown MySQL server host 'localhost:/tmp/mysql.sock' (1)
    =====
    A copy of PHPMyAdmin has not had any problems during the transition from Tiger to Leopard, nor have local copies of WordPress and Drupal.
    Any advice would be appreciated. I'm new to the subtleties of Apache/PHP/MySQL on Leopard, so please be gentle.
    Thanks.

    Thanks for the swift response.
    I'm familiar with the socket location issues with MySQL on Mac OS X. My local copies of WordPress and PHPMyAdmin both work with their configurations pointing to the socket at /tmp/mysql.sock. These installations were working, along with SugarCRM, before the Leopard upgrade. Only SugarCRM has stopped working after the upgrade.
    Is there something I misunderstand about your pointer?
    - O.

  • 1 of 2 USB ports stopped working after 10.7.2 upgrade

    I have the newest Macbook Pro.  I upgraded to 10.7.2 today and immediately after, 1 of my 2 usb ports stopped working.   Thought it may be the cable, so I switched cables.  Tried plugging in my iPhone, my portable drive and nothing.   Both work on the other port though.   Both ports worked fine before the update. 
    I've rebooted 4x. 
    Suggestions?

        Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
        "Resetting SMC on portables with a battery you should not remove on your own".
      If this does not help, contact Apple.
      Genius Bar reservation
      http://www.apple.com/retail/geniusbar/
    Best.

  • First USB port stops working after random time and won't work until I restart

    Hey guys
    I have this problem on my late 2011 Macbook Pro 13 inch,
    It's been for a year already and it really freaks me out and drive me crazy
    My first USB port next to the thunderbolt stops working after like 3 days, and it won't respond until I restart my computer or log off and log in again.
    If I restart my computer, USB stops working after 3 days and won't respond until I restart
    If I log off it works for like a couple of hours and then stops again
    I have tried EVERYTHING, SMC reset - no luck, PRAM reset - same results, Upgraded to lion same results, Upgraded to mountain lion - SAME RESULT
    And I can't take it to an apple store because I'm not from the US
    I am 100% sure this is a software problem and I've seen here that many people have faced this problem
    Please help, it really freaks me out

    ElectroSpyzz wrote:
    Hey guys
    I have this problem on my late 2011 Macbook Pro 13 inch,
    It's been for a year already and it really freaks me out and drive me crazy
    My first USB port next to the thunderbolt stops working after like 3 days, and it won't respond until I restart my computer or log off and log in again.
    If I restart my computer, USB stops working after 3 days and won't respond until I restart
    If I log off it works for like a couple of hours and then stops again...
    I'm sure this isn't what you want to hear but unless you really are using your laptop 24 hours a day, is there any reason why you don't just shut it down and reboot when you're ready to use it again? I have to wonder how many other MacBook Pro owners potentially have the same problem but when they quit computing for the day, their computers quit too.

  • Right USB Port stops working after disconnecting device since 10.9.2

    Hi,
    Since updating to 10.9.2 the right USB port on my MBA stops working after diconnecting a device (tested: external hard drive, USB flash drive, USB HSPA Modem). The only way to get the port recognizing the device on that port is to do a restart. If the device is connected from starting the MBA it works fine, if I then eject the drive and reinsert it or a different USB device the device doesn't get recognized. The devices do get power, my WD passport ultra spins up just fine, the USB HSPA modem also indicates it's working (with signal) but nothing shows up in finder or diskutility. If the modem is connected from start (and thus working) and then disconnect from the internet but not remove the drive I can reconnect to the internet. The problem only occurs after disconnecting the device. The port becomes inactive. The left USB port works as expected.
    Steps I've taken:
    Disk Persmission
    PRAM
    SMC
    Reapplied the 10.9.2 update
    Sent feedback to Apple
    Some Output:
    Boot Mode: Normal
    Total CPU usage:
       User 11%                    System 10%
    Max %CPU by process (name, UID, %):
       WindowServer         0   4.6
    Loaded extrinsic kernel extensions:
       at.obdev.nke.LittleSnitch (4052)
       com.driver.JRDUSBModemData64 (4.0.5)
       com.protech.NoSleep (1.3.3)
    Loaded extrinsic daemons:
       net.sourceforge.MonolingualHelper
       com.oracle.java.JavaUpdateHelper
       com.oracle.java.Helper-Tool
       com.microsoft.office.licensing.helper
       com.freemacsoft.appcleanerd
       com.adobe.fpsaud
       at.obdev.littlesnitchd
    Loaded extrinsic user agents:
       com.oracle.java.Java-Updater
       at.obdev.LittleSnitchUIAgent
    /Library/LaunchAgents:
       at.obdev.LittleSnitchUIAgent.plist
       com.oracle.java.Java-Updater.plist
    /Library/LaunchDaemons:
       at.obdev.littlesnitchd.plist
       com.adobe.fpsaud.plist
       com.freemacsoft.appcleanerd.plist
       com.microsoft.office.licensing.helper.plist
       com.oracle.java.Helper-Tool.plist
       com.oracle.java.JavaUpdateHelper.plist
       net.sourceforge.MonolingualHelper.plist
    /Library/PrivilegedHelperTools:
       com.freemacsoft.appcleanerd
       com.microsoft.office.licensing.helper
       com.oracle.java.JavaUpdateHelper
       net.sourceforge.MonolingualHelper
    Extrinsic loadable bundles:
       /System/Library/Extensions/JRDMassStorageDriver32.kext
                 (No bundle ID)
       /System/Library/Extensions/JRDMassStorageDriver64.kext
                 (No bundle ID)
       /System/Library/Extensions/JRDUSBModemData32.kext
                 (com.driver.JRDUSBModemData32)
       /System/Library/Extensions/JRDUSBModemData64.kext
                 (com.driver.JRDUSBModemData64)
       /System/Library/Extensions/LittleSnitch.kext
                 (at.obdev.nke.LittleSnitch)
       /System/Library/Extensions/NoSleep.kext
                 (com.protech.NoSleep)
       /Library/Audio/Plug-Ins/Components/A52Codec.component
                 (com.shepmater.A52Codec)
       /Library/Internet Plug-Ins/Flash Player.plugin
                 (com.macromedia.Flash Player.plugin)
       /Library/Internet Plug-Ins/JavaAppletPlugin.plugin
                 (com.oracle.java.JavaAppletPlugin)
       /Library/PreferencePanes/Flash Player.prefPane
                 (com.adobe.flashplayerpreferences)
       /Library/PreferencePanes/JavaControlPanel.prefPane
                 (com.oracle.java.JavaControlPanel)
       /Library/PreferencePanes/NoSleep.prefPane
                 (com.protech.NoSleepPref)
       /Library/QuickTime/AC3MovieImport.component
                 (com.cod3r.ac3movieimport)
       /Library/Spotlight/LogicPro.mdimporter
                 (No bundle ID)
       Library/Address Book Plug-Ins/SkypeABDialer.bundle
                 (com.skype.skypeabdialer)
       Library/Address Book Plug-Ins/SkypeABSMS.bundle
                 (com.skype.skypeabsms)
       Library/QuickLook/Pacifist.qlgenerator
                 (com.charlessoft.pacifist.qlgenerator)
       Library/Services/Clip to Day One.workflow
                 (No bundle ID)
    Login hook:
       /Library/Scripts/Hooks/login.sh
    Global login items:
       $HELPER_PATH
       $HELPER_PATH
       $HELPER_PATH
       $HELPER_PATH
       $HELPER_PATH
    User login items:
       iTunesHelper
       Sparrow
       Sort Menubar Items
       AppCleaner Helper
       SurplusMeterAgent
    Safari extensions:
       Shut Up
       AdBlock
       SafariKeywordSearch
       Disconnect
       MapTricks
    Restricted user files: 28
    Font problems: 0
    Elapsed time (s): 130
    etrecheck output:
    Hardware Information:
              MacBook Air - model: MacBookAir3,1
              1 1.4 GHz Intel Core 2 Duo CPU: 2 cores
              2 GB RAM
    Video Information:
              NVIDIA GeForce 320M - VRAM: 256 MB
    System Software:
              OS X 10.9.2 (13C64) - Uptime: 0 days 0:20
    Disk Information:
              APPLE SSD TS064C disk0 : (60.67 GB)
                        EFI (disk0s1) <not mounted>: 209.7 MB
                        disk0s2 (disk0s2) <not mounted>: 59.81 GB
                        Recovery HD (disk0s3) <not mounted>: 650 MB
    USB Information:
              EFI (disk2s1) <not mounted>: 209.7 MB
              Radha (disk2s2) /Volumes/Radha: 1.81 TB (1.73 TB free)
              disk2s3 (disk2s3) <not mounted>: 189.89 GB
              Boot OS X (disk2s4) <not mounted>: 134.2 MB
    FireWire Information:
    Kernel Extensions:
              at.obdev.nke.LittleSnitch          Version: 4052
              com.driver.JRDUSBModemData64          Version: 4.0.5
              com.protech.NoSleep          Version: 1.3.3
    Problem System Launch Daemons:
    Problem System Launch Agents:
    Launch Daemons:
                     [loaded]          at.obdev.littlesnitchd.plist
                     [loaded]          com.adobe.fpsaud.plist
                     [loaded]          com.freemacsoft.appcleanerd.plist
                     [loaded]          com.microsoft.office.licensing.helper.plist
                     [loaded]          com.oracle.java.JavaUpdateHelper.plist
                     [loaded]          net.sourceforge.MonolingualHelper.plist
    Launch Agents:
                     [loaded]          at.obdev.LittleSnitchUIAgent.plist
    User Launch Agents:
    User Login Items:
              iTunesHelper
              Sparrow
              Sort Menubar Items
              AppCleaner Helper
              SurplusMeterAgent
    3rd Party Preference Panes:
              Flash Player
              Java
              NoSleep
    Internet Plug-ins:
              Default Browser.plugin
              Flash Player.plugin
              FlashPlayer-10.6.plugin
              JavaAppletPlugin.plugin
              QuickTime Plugin.plugin
    User Internet Plug-ins:
    Bad Fonts:
              None
    Top Processes by CPU:
                  12%          com.apple.WebKit.Networking
                   6%          Safari
                   4%          WindowServer
                   3%          EtreCheck
                   2%          hidd
                   1%          Terminal
                   1%          notifyd
                   1%          opendirectoryd
                   1%          com.apple.WebKit.WebContent
                   0%          Dock
    Top Processes by Memory:
              147 MB          Safari
              137 MB          com.apple.WebKit.WebContent
              49 MB          mds_stores
              29 MB          com.apple.WebKit.Networking
              27 MB          TextEdit
              23 MB          WindowServer
              20 MB          Disk
              20 MB          Sparrow
              20 MB          CVMCompiler
              18 MB          Finder
    Nothing out of the ordinairy. Thanks for any help

    It's an Apple Pro keyboard and mouse, the dongle is
    plugged into the Mac and not the keyboard. The same
    set-up is, and has been working on all our other
    Macs.
    The sleep issue sounds interesting- hum, maybe...
    Is your keyboard plugged into one of the USB connections on an Apple monitor? If so, you may want to change that connection to one that is on the G5 itself. My monitor came with a warning note indicating that problems will likely occur if the keyboard is connected to the monitor.
    I also had a problem with the automatic sleep function. After much trouble-shooting and a logic board replacement, it was concluded that coming out of the automatic sleep function with any USB device active would freeze the entire USB bus. After disabling automatic sleep in system preferences, I've had no freezing problems. My machine works fine with the manual sleep function in the Apple Menu.
    AndyH

  • Help, 10.6.8 update, all usb ports stop working after 10hrs

    I've been running 10.5.8 for ever and finnaly tried to update to 10.6.8.. After I did it, the usb ports all kick out any connected devises after around 10 or so hours. I ran of the install disk, using disc utillty, disk repair, and repair permisions a few times and it did not help.
    I did the install a few times  again to try to see if it would help and didnt.
    i tried an erase and install and migrated everything over from my orignal back up external drive that is running 10.5.8 and issue is still  there.
    My old 10.5.8 back up external drive works fine and does not have this issue, and I have been using that as my start up drive instead and working from there. But that is not really a solution and a temp work around.
    Any suggestions would really help. thanks!

    I have a early 2008 macbookpro 2.8 duel with silver keys.
    I purchaed the 10.6 disk from the apple store. I've had the machine for years and purchased it refurbished from apple.
    I did the erase and install and migrated everything over from external drive, then did update to 10.6.8 and the usb ports still would stop working after a few hours.. Then I read on another apple community forus to reset pram, and pull out the power cable, take out the battery and hold power key for 5 seconds, then restart. that seemed to fix usb issue so far..
    But overall my computer seems to be running slower then when using just 10.5.8 and it did not wake from sleep once and I had to force power off and restart.. But maybe its just getting used to 10.6.8. we will see..
    Also, on another note, my battery is totally dead, and I can only run computer with power cable.. Will this affect things? it never did with 10.5.8..
    Oh, on my erase and install, I just did the simplest version and did not do the full erase to zero using he advanced security measures.. I just did the one where it writes on top of everything..

  • USB Ethernet stop working after 10.7.5 update

    After updated to 10.7.5, my usb ethernet stop working, and always shows it doesn't connect.
    Reinstall 10.7.5 make no difference.
    How do I solve it?
    Thanks!
    Yu-Hsuan

    Or download it directly from ASIX Electronics instead of driversworld.us.
    Product family: USB 2.0 to fast Ethernet
    Product name: AX88772
    URL: http://www.asix.com.tw/download.php?sub=downloadsearch&PSNoID=101
    I installed it and my AppleUSBEthernet started to work.
    The error i had (sudo dmesg):
    AppleUSBEthernet::monitorLinkStatus - Link down, Device b470200
           0        0 AppleUSBEthernet: monitorLinkStatus - Link partner register is bad, re-trying...
           0        0 AppleUSBEthernet: monitorLinkStatus - Link partner register is bad, trying to reset...

  • After upgrading to 10.8.3 my Apple USB keyboard stops working after about 3 hours

    Mac Pro 3,1
    OS X 10.8.3 Server
    32GB RAM
    Apple USB Keyboard works fine after reboot (typing on it now), stops responding after about 3 hours.
    I see nothing in Console that looks like the culprit. Here is everything around the last time it happened - between 11:28 and 11:30 they keyboard just stopped working. Unplugging and re-plugging doesn't bring it back. Changing USB ports doesn't bring it back. Rebooting is the only thing that seems to work. Bluetooth keyboard works before and after.
    3/25/13 11:28:08.503 AM mdworker[4631]: Unable to talk to lsboxd
    3/25/13 11:30:00.962 AM CalendarAgent[768]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1003 "A server with the specified hostname could not be found." UserInfo=0x7fb609cb7730 {NSUnderlyingError=0x7fb60f2d0ed0 "A server with the specified hostname could not be found.", NSErrorFailingURLStringKey=https://[email protected]/principals/__uids__/A8612C91-669B-4A4B-88 04-2AA518E4842B/, NSErrorFailingURLKey=https://[email protected]/principals/__uids__/A8612C91-669B-4A4B-88 04-2AA518E4842B/, AccountName=lovemac7.brumstead.private, CalDAVErrFromRefresh=YES, NSLocalizedDescription=A server with the specified hostname could not be found.}]
    Anyone else seeing anything like this?
    Everything worked fine in 10.8.2.

    Hey Doug,
    Thanks for your post, and welcome to the Apple Support Communities.
    I understand that your keyboard backlight is not working upon startup, the following may resolve your issue:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/HT3964
    After performing normal troubleshooting, these symptoms may indicate that an SMC reset may be necessary:
    Lights
    The keyboard backlight appears to behave incorrectly (on Mac computers that have this feature).
    You may also want to reset your computer's PRAM:
    OS X Mountain Lion: Reset your computer’s PRAM
    http://support.apple.com/kb/PH11243
    Note: Resetting PRAM may change some system settings and preferences. Use System Preferences to restore your settings.
    Thanks,
    Matt M.

  • USB-hub stopped working after upgrading

    I have a macbook pro 13 inch, year 2011.
    On my desk, I attach it to a thunderbolt display. To those USB-ports, I attached the belkin desktop USB hub (model F4U017) with 7 USB ports.
    All worked fine and without a glitch untill I upgraded to OSX Moutain Lion.
    Suddenly it won't connect annything I plug into it.
    All the cables of the hubb still work fine, those have been tested.
    When I tested the hub with a very old iMac (i think still with leopard it), it worked again.
    To be sure, I also tested a 4-port hub without external power supply on moutain lion. That one still works fine.
    How come my 7-port hub won't work any longer? How can I make it work?

    Not sure.  Might be an issue with the USB drivers in mountain lion.
    I've had an issue with a couple hubs not working after plugging back into my macbook pro while it's on.
    Fixed by restarting my computer, but that's super annoying and takes me back to my Win 95 days.  Never saw this issue before I upgraded to mountain lion.

  • USB- hub stopped working after upgrading to OSX Mountain lion

    I have a macbook pro 13 inch, year 2011.
    On my desk, I attach it to a thunderbolt display. To those USB-ports, I attached the belkin desktop USB hub (model F4U017) with 7 USB ports.
    All worked fine and without a glitch untill I upgraded to OSX Moutain Lion.
    Suddenly it won't connect annything I plug into it.
    All the cables of the hubb still work fine, those have been tested.
    When I tested the hub with a very old iMac (i think still with leopard it), it worked again.
    To be sure, I also tested a 4-port hub without external power supply on moutain lion. That one still works fine.
    How come my 7-port hub won't work any longer? How can I make it work?

    Not sure.  Might be an issue with the USB drivers in mountain lion.
    I've had an issue with a couple hubs not working after plugging back into my macbook pro while it's on.
    Fixed by restarting my computer, but that's super annoying and takes me back to my Win 95 days.  Never saw this issue before I upgraded to mountain lion.

  • USB modem stopped working after udev 091-3 upgrade

    I just udated my system today and my speedtouch modem stopped working. If I try to connect i get
    Connect (0.38): No such device
    So i had to downgrade to udev 091-2 and its okay now. What could be the problem?

    could you please delete udev.rules file and then reinstall udev?
    and then try again with udev 092-2, thanks.

  • Navigation and other features suddenly stopped working after I upgraded to FF4.

    A day or two after I upgraded from FF 3.6 to FF4, all the ordinary navigation features stopped working. Backspace/alt-<, even the back and forward arrows, Crtl-R to reload a page, and the address field doesn't show the current URL unless I click the identify information icon. All very odd. None of the keyboard shortcuts work.
    My bookmark toolbar does not load automatically, although I guess that Vista is the source of that issue.

    Doing a downgrade is not anything I have done or feel comfortable with. Is there a clean procedure to accomplish this?

Maybe you are looking for