My wd external driver is not recognized in Window 8

Hello,
Im using Mac Air, and my WD working well with that, but I cant use it on other computers using Window. It seems that my WD just working with Mac only ( it worked w another mac). Please help! What I can do?
And my mac does not recognize other WD used on Window ( THats my friend's WD, this person using window 8). Please help! Thank you so much for your help

yes, backup means saving your important data, and always preferably 2 archives/backups of that data.
Those who dont backup data always regret it. Putting 1000s (or more) hours of work onto a single drive (your internal HD/SSD) is asking for trouble.
another HD costs only $65....... 1000s hours of work is worth.........(a LOT).
(offload data from the HD if youre going to do this, because it will ERASE IT !)
TO FORMAT, open disk utility > select the HD you want, go to ERASE tab, format it in EXFAT (for use on both pc and Mac for read/ write).
Munmuncat
So in fact, I still need to use other driver to back up my current WD?
Need no, SHOULD yes. the general rule is "2 copies is 1, and 1 is none", and the HD inside the computer doesnt count.
Ideally ONE of those copies is stored away safely somewhere, firebox, safe, etc.

Similar Messages

Satellite A300 - Cd/Dvd drive is not recognized by Windows

My cd/dvd drive has ceased to be recognized by windows (7). I'm not sure what has caused this because it was previously working and allowed me to install office 2010.
There appear to be no restore points shown around the time when it was working.

Hi Robert Crockford,
In your case I would try deleting the upper and lower filters in registry for CD/DVD drive. This is described on official Microosft website how to do this, so just read the knowledge base article and follow the instructions:
http://support.microsoft.com/kb/314060

MSI UBO-30 External Slim Bluray Drive not recognized under Windows 8.1

Hi, does anyone here have MSI UBO-30? It is an external bluray drive from MSI. For some reason the drive is not recognized under windows 8.1 64 bit (it just says USB device not recognized). But works fine if plugged into Windows 7 machine. Anyone encounter the same issue?

Try upgrading your usb 3.0 drivers on your system. That worked with My GS70 Stealth Pro...

Stor.e slim not recognized by Windows 8.1

Hello,
A Stor.e slim external HDD is not recognized in Windows 8.1 (no problems with Windows 7). When plugged in, it s shown as a non-recognized device. Driver is being sought, but not found.

Hi
The Stor.E Slim external HDD is an 2.5 USB 3.0 HDD and it requires 900mA power in order to work properly.
I guess there is nothing wrong with this HDD but with your notebook.
The Win 8/8.1 requires different drivers and probably you need to install an proper driver in order to get the USB ports working properly (USB 3.0 as well as additional chipset driver would be also required).

External hard drive is not recognized after attempt to format

I just got a new macbook and couldn't use my external hard drive because it was formatted on a PC and only allowed me to read the data. I backed up the data on the 250gb hd and then used Disk Utility to erase the hd and format it as "Mac OS extended (journaled)." After beginning, Disk Utility stopped working and showed up as "not responding" in the Activity Monitor.
Now the hd does not show up on the desktop and can only be seen in Disk Utility. If I try to erase again or partition the hd the utility stops responding. If I try to zero out the drive it continues to say "preparing to zero" indefinately. Now the hd is also not recognized by windows except in the windows disk utility, but it does not even give the option of formatting/initializing it, so that is not an option.
Has anyone ever seen anything like this before, or have any idea of something that I haven't tried yet. I really want to get the drive working and have exhausted all the ideas I can come up with. The internet has not provided too many ideas either.
Thanks so much for your help.
Black MacBook Mac OS X (10.4.6)

I have crazy solution to format it to FAT 32, it work a couple times on my several MAxtor, and Western Digital HD. But this is the last resort and if you are not handy and familiar, don't do it.
It happen on my external HD, so I crack the enclosure open, pulled the HD out and attached it as internal HD on a PC after adjusting the jumper to master and make sure no other HD attached to the motherboard. Make sure the motherboard detected (you can see it from bios menu).
Insert a bootable installer disk before XP ('98, ME, or 2000), and start from there until a promt comes, and type fdisk and you delete the old partition and create a new partition and restart once using the disk still and format it using FAT 32.
After that you put it back to the enclosure, and mount it to MacBook as a new HD with default factory format.
If you don't have the installer disk, this might help :
http://www.bootdisk.com/
But if your maxtor still under warranty better talk to them first and they might willing to reformat it for you.
Hope this help your external back and let you use it on your MacBook.

My external USB drive is not recognized by Win XP

Hi!
I have an external USB drive that is HTF+ formatted. It is not recognized by Windows XP. If I start the windows disk manager it gives me the option to initialize the drive. Do I dare to do this? Will it not erase the information on the drive?
Thanks for any help!
/ Anders

Hi Anders and welcome to Discussions,
I have an external USB drive that is HTF+ formatted. It is not recognized by Windows XP. If I start the windows disk manager it gives me the option to initialize the drive. Do I dare to do this? Will it not erase the information on the drive?
Yes it will !!
Although with the BootCamp 3.0 Drivers (from the OSX Snow Leopard DVD) and the 3.1 Driver update (downloadable) Apple has introduced read-access to HFS+ partitions from Windows this feature seems to have some serious problems for some people.
Personally I see this feature as "experimental" at the moment.
XP itself knows nothing and therefor can not use/see HFS+ partitions and GPT (GUID partition table) harddisks.
You might wanna have a look (or buy) at MacDrive http://www.mediafour.com/products/macdrive/ which right now is the better solution.
Thanks for any help!
/ Anders
Hope it helps
Stefan

My external hard drive is not recognized by my computer.

My external hard drive is not recognized by my computer. I used it earlier and it was fine however my computer froze and I unplugged my hard drive without properly ejecting it. Now when I plug it in nothing pops up. I've tried on three different computers and no luck. I hope this is fixable! Please help.

Care to share which OS you are using?
Repair permissions & restart your computer.
Zap the PRAM

New hard drive is not recognized by my MacBook Pro.

New hard drive is not recognized by my MacBook Pro. The supplier says I need to update my BIOS. True? How do I do that?
Hard drive: NN2-72-500-SSE Seagate Momentus 7200.4 (ST9500423AS) 500GB Laptop Hard Drive
Mac OS: Mac OS X Lion 10.7.5

I went through a similar issue with a Seagate Momentus 750GB HDD/8GB SSD with my late-2011 MBP. No matter what I tried, the machine would not recognize the drive.
To test it, I installed the drive in an old ThinkPad, and it worked fine. Then I tried installing it in my PS3, and the drive worked fine there, too. It was only the MBP which had issues.
I don't *think* Macs have a BIOS to update. But I know my MBP has issues with certain HDD's (including another external which works fine on other Macs and all Windows machines).
You might be able to find my thread by searching under my username, perhaps something in there will offer a tip. Otherwise, you might have to go the same route I did: install a WD Scorpio Black instead. Or upgrade to an SSD.
Good luck to you-

Yoga Pro 2 - Display not recognized in windows (Driver or Hardware issue?)

Out of warranty by a month!
Yoga Pro 2 - 256gb, installed new wireless card a month ago. Windows 8.1
The touchscreen still works while the screen is black.
System restarted after sleep mode I think.
The Lenovo logo is displayed, seems to load windows, but when windows loads (I don't see it load so this is an assumption) the screen blanks and the black light is on.
I can connect an external monintor which will connect after a return from sleep mode(odd). Which then turns the backlight off.
When on the external monitor the internal display is not even recognized by windows.
When I boot in safe mode, the internal screen works fine with of course limited capability.
I have reloaded display drivers from the support site.
Right now my internal monitor is not recognized by windows and is dark, and I can use an external monitor.
Anyone have any clues as to what my be going on? Hardware, driver etc???
What information can I provide?
Solved!
Go to Solution.

This is a pretty weird issue with conflicting observations.
1) Screen works in Safe Mode but not in regular boot. (So, not hardware issue)
2) Display works on external monitor in regular mode. (So, not drivers issue)
Did you install the wireless card yourself? Did you unplug the display cable while installing the card?
Could you re-open and check that all connections are good?
Is the Wi-Fi card working well?
I would also recommend a complete reset of the laptop to eliminate the possibility that this is a corrupt driver. You can use the NOVO button to reset your laptop. Make sure to make a backup on external drive for your personal files.
Current System - Lenovo Y510P, GT755M SLI, 8GB RAM, 1TB HDD + 24GB SSD
When your plans fail, your Real Story begins!!

Need to do a full restore but my backup drive is not recognized

My backup drive is not recognized by Migration Assistant nor on OS x 10.6.8 start up. Need a full restore via Time Machine.
On startup with new drive, I initially selected to restore from Time Machine backup. It asked to connect the drive which I did but it did not recognize. So I moved on thinking I could restore through Time Machine.
Did some research and decided to try Migration Assistant. Again, the only disc displayed was the hard drive and not the external "My Passport" drive.
I can see the backups on the My Passport drive and even checked (repaired) that disc and still not working.
Any ideas on how to get this to work? Needless to say, I was very pleased with the concept of Time Machine but if the restore doesn't work it doesn't do much good.
Thanks in advance!

I think I found the right path.
- Inserted the OS x 10.6.8 install DVD
- Selected language
- Rather than continue with OS install, selected the "Utilities" menu item and found the restore from backup option
Next step, the search found the external drive. From there I selected the date and now the restore is running.
Thanks for the replies!

External Drive Files Not Showing Up on Mac but files do shows Up on PC

External Drive Files Not Showing Up on Mac but files do shows Up on PC
i had the Ex HD for about 3 years running smoothly on my mac but recently everything disappeared. plunged it into a pc to see if it read my files and it did. what can i do? to make it work on mac again. i don't want to reformat that drive because i have important applications (DMG) and other zip photo video files in the drive.

yes. i did.
...i have tried "verify" & "repair" but they didn't pass the san test. and when i "unmounted/mount" a error message popped up say that there is a application running off the drive but there nothing (i see) running, to close all activity

Hard drive not recognized during windows server 2008 setup

hard drive not recognized during windows server 2008 setup

Hi,
Whether the hard disk is recognized in BIOS?
Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
a suitable driver is installed.
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

TS3648 great, but my MBA did not come with an installion disc, only a tiny jump drive that is not recognized by windows; and I can't get the contents of that burned to a DVD either. So how the heck do I get the drivers into Windows 7? My MBA has bootcamp

great, but my MBA did not come with an installion disc, only a tiny jump drive that is not recognized by windows; and I can't get the contents of that burned to a DVD either. So how the heck do I get the drivers into Windows 7? My MBA has bootcamp 3.0.4.

Here's what I get:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0 mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:11:24:7d:e7:1e
media: autoselect (none) status: inactive
supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::211:24ff:fe28:2e71%en1 prefixlen 64 scopeid 0x5
inet 169.254.115.141 netmask 0xffff0000 broadcast 169.254.255.255
ether 00:11:24:28:2e:71
media: autoselect status: active
supported media: autoselect
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 2030
lladdr 00:11:24:ff:fe:7d:e7:1e
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>

CD Drive or DVD drive is missing or is not recognized by Windows or other programs - this happens any time I upgrade itunes

I just upgraded to the new version of itunes for my ipod touch. My CD Drive or DVD drive is missing or is not recognized by Windows or other programs occurs and it does not show up listed as part of my computer. How can I fix this?

Your DVD drive? Why would this be missing after a iTunes download?

My external drive is not showing on my desktop

My external drive is not showing on my finder and it is turned on and connected by firewire. Is there an alternate way to force my G5 to see the external drive?
Laura

Check the settings in the General and Sidebar tabs of the Finder's preferences. If those are set properly, open the Disk Utility in the /Applications/Utilities/ folder and try mounting and/or repairing the drive.
(77081)

My wd external driver is not recognized in Window 8

Similar Messages

Maybe you are looking for