My wireless earbuds work just fine, but some third-party apps play audio only through the iPod speaker even though the buds are properly connected.

My wireless earbuds work just fine, but some third-party apps play audio only through the iPod and iPhone speaker even though the buds are properly connected. Does anyone know why and is there a solution?

Assuming you are using Bluetooth headphones, do the apps have the option to use Bluetooth?
The app should have an option to select the speaker (or wired earphones) or the Bluetooth headphones.
You can also try:
iOS: Troubleshooting applications purchased from the App Store
Contact the developer/go to their support site if only one app.
Restore from backup. See:
iOS: How to back up              
Restore to factory settings/new iPod

Similar Messages

  • I have OS 10.8.2 and use wireless at home just fine. When I visit a friend with only a cable modem internet my Mac Book Pro will not connect. What do I need to do?

    I have OS 10.8.2 and use wireless at home just fine.
    When I visit a friend with only a cable modem internet my Mac Book Pro will not connect.
    I see that the Mac Book Pro is picking up the internet when I check the internet preference section but it will not open Safari.
    What do I need to do connect via a cable modem?

    You need to power off the modem for 15-30 seconds, then power back up and then connect. The modem is remembering the last connection (your friend).

  • Hi, I m using an iPhone 4 and my yahoo push email was working just fine but for the last few days I am experiencing some problem that is the emails are not getting pushed , I have to manually fetch the mails. So what could be the reason for this....

    Hi, I m using an iPhone 4 and my yahoo push email was working just fine but for the last few days I am experiencing some problem that is the emails are not getting pushed , I have to manually fetch the mails. So what could be the reason for this.....I have set the email setting to "push" mode. Moreover I can't edit the mail server address ....current it's on Yahoo SMTP server

    Will it get rectified and restored...if so after how long. What could be the reason for such outage kindly share,  as I am facing real problem because of this...

  • HT5012 I had my iPad replaced this past Thursday and it is working just fine but my Bluetooth keyboard is not now working.  I need to know what I need to do to get it to work.  Thanks, Joyce Lenzo

    I had.my iPad replace this past Thursday at the Apple store under warranty and it is working just fine but the Bluetooth separate keyboard is not working.  Thanks, Joyce Lenzo

    Maybe:
    Wireless input devices: Bluetooth frequently asked questions

  • HT204291 I can play videos from youtube and it does just fine, but when I try to play videos i've bought from itunes in my "videos", it plays the sound but no video.  Please advise,,,

    Using airplay, with Iphone5 latest os, appletv3, I can play videos from youtube and internet just fine, but when I try to play videos bought from Itunes in my "videos" file, it only plays sound, no video.  Please advise,,,

    I am also having this issue.  Hear but not see. I am using the iTunes video app on my iPad to play a show I bought on iTunes.   A little pop up box comes up on the lower left of my tv showing the show , I can hear it but not see it.  Rebooted Apple TV and iPad. No help.  

  • IOS 5 Notifications Not Working for Some Third Party Apps

    Recently updated my iPhone 4 to iOS5. Notification center worked perfectly for a week, but then I noticed that certain apps (Beluga) would not show up in the notification center despite receiving new messages. The home page didnt update with a badge either. It seems as if push notifications for some third party apps are not working correctly.
    I have already attempted all of these to correct the problem to no avail:
    1. Confirming notification settings for each application
    2. Turning notifications off and then on
    3. Removing and reinstalling app
    4. Restarting the iPhone
    5. Shutting down and powering up the iPhone
    6. Restoring the iPhone

    Having the same problem...  Ipad 2 running iOS 5 working fine.  My iPhone 4s gets the occasional Facebook notification but not much else.  Got home today and had about 5 notifications on the iPad that never came through to the iPhone.  Tried everything you tried and nothing....

  • IT tunes music - some, a lot, of somgs stop playing half way through. the files are all ok and complete? ive tried downloading / updating but no joy?

    IT tunes music - some, a lot, of songs stop playing half way through. the files are all ok and complete? ive tried re - downloading / updating but no joy? can anyone help its most annoying

    Yes, in theory re-converting would lessen the quality further. However, I have heard people claim (unsubstantiated) that if you are encoding with the same encoder at the same bit rate, then since it will use the same algorthymn, it won't really change the file. I have absolutely no idea if that is true or not.
    But... I figure some slight loss in quality re-encoding is still better quality than a song that only plays half way and then stops, right? I suppose you could always tag those files in the comment section with something like "Re-Encoded" and then later if you gain access to your old CDs, you can then make a Smart Playlist to gather those songs and then re-rip them again from your CDs.
    Cheers,
    Patrick

  • No Audio on some third party apps?

    I just recently bought my iPad 2. I loaded most of my apps, music, movies onto the device as you would with any new toy. But now some third party apps do not have audio. I tried Angry Birds RIO HD, Angry Birds, etc. nothing. When I use Garageband and iMovie the speaker and headphones work fine. Any one have suggestions?

    I solved the problem. I must have switched from Mute to Lock Rotation while playing an app so it freaked out the iPad, all I had to do was switch back turn it on and off and it worked!

  • My modem works just fine, but my airport extreme refuses to connect to the internet.  I even reset it more than once, changed the DNS servers and still nothing.  Help

    Ok so recently we were having problems with our phone.  We had to disconnect our modem in order to fix the phone lines and when that happened, our airpot extreme disconnected itself from the internet.  No matter what I did i could not get it to connect back.  I would power down the modem, I would reset the AE and nothing would happen.
    I tried changing the DNS server and nothing happened.  I always get the same messages in the airport utility app: No internet connection and no DNS server
    Nothing I seem to do works.  I do know for a fact though, that the problem is not the modem.  I have connected it through ethernet to other devices and the internet has worked just fine. 
    Please please please if anybody sees this help me out!!

    Since you feel good about having internet access up to your Airport, I would suggest as a next step checking your Airport's status light to see if it is giving any clues as to what may be going on. Below is some info on what the light can indicate
    AirPort Express Status light sequences and what they indicate.
    No light (Off) - AirPort Express is unplugged
    Solid green - AirPort Express is on and working properly.
    Flashing amber - AirPort Express is not set up or cannot establish a connection to the network or
    the Internet. Use AirPort Utility to find out the cause. See “If Your AirPort Express
    Status Light Flashes Amber” on page 20.
    Solid amber - AirPort Express is starting up.
    Flashing amber and green - There may be a problem starting up. AirPort Express will restart

  • Firefox closed and now it says that I get a connection error. IE and AOL work just fine but I use my Firefox won't connect

    I use Firefox for going online all the time. Now, suddenly, when I try to connect it says the server can't be found. Internet Explorer and AOL are working just fine. However, I don't want to use them.

    How do you fix this?

  • IPad not loading all the way,esp.on FB ,on wireless,it's working just fine but this

    I 'm having a problem trying to load all my pages on Facebook,......iPad loads maybe one full screen here and then won't go any further. Even the loading circle ....lefthand top.....won't go round? I'm getting my emails in just fine ,it's just a few sites .......news.com.au loads okay and I can 'turn'over to the next screen etc but the  minute I get on Facebook, this darned  pad has a 'brain lock!'
    My big PC is working okay ,can get everywhere on Facebook but not my iPad?
    Wireless is connected too so what can be wrong? Only had this for 8 months ,not an old pad by any means. It's been like this for about 24 hours now .when I hit a page link ,it just sits and looks at me:) No loading circle or anything!
    Appreciate some suggestions,please?
    I live in West Oz.
    Louise

    By the way,I use Safari to surf internet.
    Louise

  • Home sharing is not working in apple tv after upgrading apple tv to 4.2.2.  I've had apple tv working just fine for some time now and after upgrading, it stop working and prompts me in Apple tv to turn on home sharing in Itunes.  It's on.

    It asks me, in apple tv when I go to my "Library" to turn on home sharing.  It's on.  When I turn it off and back on I can access my itunes stuff fine for a day or two and then it doesn't work again.  I've tried unplugging appletv, reboot the router (att uverse), and then plug in apple tv again and it doesn't help.  it's still give me the message.  the only thing that works, temporarily, is to turn off home sharing and turn it back on.
    I'm using itunes version 10.5.0 on windows 7.  can someone help me with this?   I can't run up and down the stairs all the time.  I have bad knees and other conditions that stop me from doing that.  Please help.
    Thanks.
    Jim.

    Hey all,
    I've been having similar problems so I put a packet analyzer on the network to see what's really happening. (Apologies in advance if this post is too techno-babbly...)
    Some background:
    How do Apple devices find each other over the network?
    iTunes with home shaing turned on sends out a message to a special IP address called a multicast (224.0.0.251, in this case.) All your Apple devices listen to this multicast address and respond over that same address. This process applies to iTunes, AppleTV and Apple Remote at least (those are the things I've been testing with.)
    How do Apple devices communicate with each other once they're found?
    Once they find each other, they establish a Transmission Control Protocol (TCP) communication session. This connection is only between two devices. In this case, iTunes and AppleTV or Apple Remote and AppleTV. The TCP session is how data gets transferred between devices.
    The problem:
    I captured the protocol traffic between my PC and AppleTV first with the firewall software turned off. In my case, I use Norton 360. What I see is iTunes and AppleTV communicating over the multicast address every 100 seconds. My iTunes usually 'disappears' from AppleTV and the Apple Remotes within about 5 minutes so I left the firewall off for half an hour and everything worked fine. I turned the firewall software back on and then restarted everything. iTunes then did the device discovery and all the devices found each other. Then, after a period of about five minutes of inactivity, the multicast discovery protocol stopped being sent by my PC. Why? I really don't know. From watching the apple protocol's timing, contents and behavior, I see nothing wrong with the implementation. I've done troubleshooting on other location-based multicast protocols for work and have seen some dumb things but Apple's protocol is done correctly and behaves exactly as I would expect.
    The solution:
    I put a rule into my firewall software explicitly allowing the multicast IP address and also the local subnet that my devices use. I then moved the new firewall rules to the top of the list to ensure that they will be 'hit' before any of the other rules in the list. After that, I left the firewall on and tested for a while then left everything idle for an hour. When I came back, everything still worked. I would suggest that replacing your firewall software won't necessarily help you here. You just need to make sure that the rules for the Apple stuff are put in manually and are at the very top so that another deny rule in the list doesn't trigger before the new permit rules. Hopefully it goes without saying but doing the above leaves your PC completely wide open on the local network so, if you use wireless, please be sure to use encryption on it.
    Hope that helps...

  • P45 Platinum - Vista works just fine, but unable to get into BIOS

    This is my first build, so I'm still learning a lot. Be kind!
    I'm using the P45 Platinum with an Intel Core 2 Duo 3.0ghz Wolfdale cpu, 2 2gb sticks 1066mhz G-Skill ram, a Corsair 750w PSU, EVGA Nvidia 8800GTS video card, a 74gb WD Raptor HDD and a 250gb WD Caviar HDD (both SATA). I'm currently running 32bit Vista until 64bit has more support.
    I have never been able to access the BIOS - before Vista was installed the splash screen was too fast so I kept missing my oppurtunity to enter BIOS, so I went ahead and put in the Vista install DVD. It installed just fine - it doesn't see my second HDD, but I expected that due to it being SATA.
    I want to enter the BIOS to disable the audio so I can download the new Realtek audio drivers (I have no sound, even after installing the driver off the CD), but when I start up the computer and hit DEL (when prompted), it takes me to the Windows Boot Manager. Several times I have repeated the process and every time it takes me to the boot manager instead of the BIOS. The BIOS is obviously working, I just can't access it.
    Any help is appreciated.

    Quote
    I have never been able to access the BIOS - before Vista was installed the splash screen was too fast so I kept missing my oppurtunity to enter BIOS
    Simply keep hitting  >DEL< as soon as the Splash screen appears.  If that doesn't help, clear CMOS with main A/C power cable removed from PSU.  Upon restart the system should hold with a CMOS Checksum error and give you the chance to hit F1 to enter BIOS Setup.  Now you can load "Optimized Defaults" and disable the BOOT LOGO.

  • Its working just fine but does it look good? Take a look and give me your advice!

    I got to say that this is my first finnished labview program, and  it's working fine, almost no problems. But i'm not that shure about
    this huge while loop with all its instructions. Normaly a while loop takes 1 ms to iterate once, but this loop takes more than one ms,
    I'm using another subVI to catch data up to 5 ms. / sample as output from measurement device to  the while loop in this Sub vi, and then from this sub VI i'm initializing the data value read from the Measurement device, to a global variable that i read in this huge while loop.  I belive that the subVI while loop iterates several times before the huge loop iterates once. Meaby thats why my graphs for the data are plotting more than one data at a time.
    Take a look and give your advice, it seems that all the measurements are well. And I don't really got problems with the program when running, exept from small delays when I switch the sample rates.
    Regards
    Zamzam 
    HFZ
    Attachments:
    WhileLoop.JPG ‏354 KB

    I agree with Titou.
    Wow!  That's an eye-full. 
    There are some functions like setting audio On / Off that may not need to be in there.  Or do they?  You'd have to describe what the loop is supposed to do.  Same comment for the indicator display settings on property nodes.  Do you intend to turn them on/off a number of times during an iteration of the loop?
    You should "divide & conquer".  By that I mean, use sub-vi's that are function specific.  As mentionned by Titou, you should have a look at the development guidelines.   Basically, now that you have a working loop, you can improve it by creating some sub-vi's, revisit some items that may  not need to be in the loop.  As a matter of fact, you could create some control & indicators and maybe transform the loop into a sub-vi as well. 
    There are many Case Statements that you could convert to sub-vi's and that way, you could eliminate the global variables by using indicators and wiring directly to them.
    However, I would have to say that the value for "Write Flow Data" might become unpredictable due to race conditions.  Revisit how the value(s) are set for that one.
    But it does look like you had some fun doing this one.  Which is the most important thing.  To have fun implementing solutions with LV.
    Happy wiring!
    JLV

  • My iPod was working just fine but all of a sudden it won't connect to iTunes?

    I've done everything I can think of! I system restored my computer, I reinstalled iTunes and even repaired it like two times, I've even installed an older version of iTunes. In the older version of iTunes it at least registers that I've connected my iPod to it... except it says "songs cannot be added to the iPod "%1$S" because all of its space has been reserved for data." And something about a FireWire and "You must connect using FireWire to restore the iPod ~^FILENAME"."
    I've even ran multiple diagnostics scans through iTunes on the connectivity issue and this is what I've gotten each time:
    Microsoft Windows 8 x64 Home Premium Edition (Build 9200)
    Hewlett-Packard HP 2000 Notebook PC
    iTunes 11.1.5.5
    QuickTime 7.7.4
    FairPlay 2.5.16
    Apple Application Support 3.0.1
    iPod Updater Library 11.1f5
    CD Driver 2.2.3.0
    CD Driver DLL 2.1.3.1
    Apple Mobile Device 7.1.1.3
    Apple Mobile Device Driver 1.64.0.0
    Bonjour 3.0.0.10 (333.10)
    Gracenote SDK 1.9.6.502
    Gracenote MusicID 1.9.6.115
    Gracenote Submit 1.9.6.143
    Gracenote DSP 1.9.6.45
    iTunes Serial Number 0080BBF80BE3----
    Current user is not an administrator.
    The current local date and time is 2014-04-22 16:40:52.
    iTunes is not running in safe mode.
    WebKit accelerated compositing is enabled.
    HDCP is supported.
    Core Media is supported.
    **** External Plug-ins Information ****
    No external plug-ins installed.
    **** Device Connectivity Tests ****
    iPodService 11.1.5.5 (x64) is currently running.
    iTunesHelper is currently not running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    No Universal Serial Bus Controller found.
    No FireWire (IEEE 1394) Host Controller found.
    Most Recent Devices Not Currently Connected:
    iPod touch (4th generation) running firmware version 6.1.6
    Serial Number:          -----
    iPad (4th Generation) (Wi-Fi) running firmware version 7.1
    Serial Number: ----
    Can anyone help me out? I'm so frustrated with my iPod.
    To make it even better, my iPad won't even connect either.
    However my friend has the same computer and it will connect to hers just fine. (The iPad will at least)
    Thank you in advance for any and all help you can give me. ;~;

    See
    iOS: Device not recognized in iTunes for Windows
    - I would start with
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or              
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
    - Then do the other actions of:
    iOS: Device not recognized in iTunes for Windows
    paying special attention to item #5
    - New cable and different USB port
    - Run this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    Also see:
    iPod not recognised by windows iTunes
    Troubleshooting issues with iTunes for Windows updates
    - Try on another computer to help determine if computer or iPod problem

Maybe you are looking for