My wrt300n just lost connection

My power went out and my wrt300n router is not working properly. The pc link on my modem does not light up when I connect, but works fine when connected directly to computer. The lights on the router stay on continuously even though no cables are plugged into the ports. Is there anyway to reset this or is my router just dead?

Hi GregW and welcome to the forums!
You can try resetting the router to factory defaults. Here is the link for the step by step procedure.
Resetting the Linksys Router to Factory Default
If the router's lights still continue to stay on even w/o anything plugged in, then it may be faulty. Hope this helps.

Similar Messages

Printer just lost connection

I have been using an Appletalk network printer and this morning it has lost connection!?!?! I just printed to it a few days ago. It is a Xerox printer running through our network here at work. Nothing happened to the actual printer... it is still up and running. This printer is in a work enviroment and can be accessed from other computers in the office. It is weird because I have a different printer that I also use on the network and 2 days ago I lost connection to it as well. I was able to get that connection back. This one won't reconnect though....... I am using a G5 desktop computer running 10.4.5, which I need to upgrade to 10.4.6 but I don't think this has anything to do with it, I use this printer all the time. I have run disk utilities and have deleted and added the printer several times. I did get this while the printer was trying to connect when I added a new one.... nbp_sendfailed got=-1 ...... I have pinged the IP address and it works fine....
Any help would be greatly appreciated......
Marc[

Any luck on a solution to this yet?
I just had the exact same problem. Printed a couple of hours ago, then nbp_sendfailed error message when I tried to add any printer in the building. None of my existing printers will work.
OS X 10.4.6
Lexmark printers
Nothing new added or changed.
I have run Disk Utility and Disk Warrior.
Any other suggestions would be very helpful.
Thanks.

Had to purchase two OS X system upgrades, new iPhoto etc. just to connect new iPhone 5 and now half my apps won't work. No rosetta and missing lost dogs pics from iCloud...HELP!

I had to purchase two OS X system upgrades, snow leopard and mountain lion, just to connect my new iPhone 5 and somewhere between uploading iPhone 4S pics to iCloud some important pics disappeared then installed new iTunes and purchased new iPhoto all just to connect new iPhone 5 and now half my apps won't work. No Rosetta to make apps work but its not as simple as upgrading apps and missing lost dogs pics from iCloud...HELP!

File a complaint with Apple for not giving adequate warning before upgrading OS X that it would render PPC programs dead.
That someone at Apple said requiring the iPhone 5 to have 10.8 (10.6.8 is the minimum actually) and in order to remain a loyal Apple customer they need to fix this mess and revert your machine and software back to 10.6.8
You see, 10.6.8 would have ran your iPhone 5 and ran your PPC based software, so whoever told you to upgrade to 10.8 was wrong and they need to fix your machine.
It can be reverted to 10.6.8 yourself.
How to revert your Mac to Snow Leopard
Most commonly used backup methods

"Lost connection with AIM" error message

Hi all,
I've been a long-time iChat user — I've had very few problems, but now, at home, whenever I've been connected for about 10-15mins, iChat just disconnects with the simple iChat Connect Alert that the app has "Lost connection with AIM. The connection with the host was unexpectedly lost."
My Buddy List collapses to a "disconnected" header and I diappear from my Buddies' buddy lists. If I'm in the middle of a chat (video, audio or text), the chat continues uninterrupted, but I still disappear from people's lists as if I'd disconnected manually. Weird.
The net result is that I have to keep checking to see if I'm connected and then reconnecting all the time. A real pain in the proverbial.
It only happens at the house. My laptop doesn't disconnect if I'm at the office, for instance.
I have cable, coming in to Netgear 814v2 router; out to an 8-port gigabit switch, which then feeds my three main machines. All via ethernet cabling.
All machines have the same problem described above.
I've made the usual Quicktime setting changes.
I've listed the necessary ports in my Mac firewall settings (even though the firewall is turned off).
Each machine has a dedicated IP issued by the router (10.0.0.2 thru 10.0.0.5)
The router firmware is up to date.
What else is there?! I have no problems initiating or joining any sort of chat with my buddies around the world. I have excellent bandwidth. My internet and email are never interrupted 24/7.
Can someone help me? Pretty please?
17" Powerbook G4 & Dual G5 2.5Ghz Mac OS X (10.4.7)

Hi
Try this log on to AIM on port 443 rather than port 5190
Go to IChat > Preferences > Accounts.
Log out of AIM and then use the Server Settings tab
Set the port to 443.
Log back in again.
Tony

NVIDIA OpenGL driver lost connection with the display driver

Alienware M14x Laptop
Windows 7-pre 64-bit
8gb ram
3gb Video: NVIDIA GeForce GT 555M
Intel i7 2760QM
AE CS4
AE keeps crashing. I get the following message while doing something as simple as scrubbing through the timeline, or changing opacity of a layer. in 1080p, I have a picture layer, a solid, some color corrections, and that's it. i just got this new computer and i have never had this problem on my old computer.
this message appears after AE crashes."The NVIDIA OpenGL driver lost connection with the display driver and is unable to continue. The application must close."
this message appears in the taskbar: "Display driver stopped responding and has recovered. Display driver NVIDIA Windows kernel Mode Driver, Version 267.21 stopped responding and has successfully recovered"
any ideas on how to stop AE from causing my display driver to stop working?
Thanks, Ramzi Rebeiz

For anyone picking up this thread (it's probably too late for rrebeiz40 by now!) I have come across a simple but apparently very effective tip that has solved the 'OpenGL driver lost connection' issue for many people using various NVIDIA with various Adobe progs (incidentally a lot of these seem to crop up on Dell machines, especially Notebooks).
(It fixed my issue with Premiere Pro CS4 - GeForce GT 555M on Win 7 Ultimate 64-bit, Dell XPSL702X).
It's posted on http://forum-archive.developer.nvidia.com/index.php?showtopic=5331&st=40 (look for the last post, No 50) as follows:
THIS FIX APPEARS TO WORK...found on an Adobe forum
"This issue led me to this fix: go to NVIDIA Control Panel --> Manage 3D Settings --> Global Settings, and switch "Power Management Mode" to "Prefer Maximum Performance" (the default "Adaptive" setting seemed to be the culprit). And that's it! The key here is changing the "Global" setting, as my individual programs were already set to "Prefer Maximum Performance." I can cause the error to reoccur by changing back to "Adaptive."
Otherwise lots more ideas on this site: http://www.instructables.com/id/How-to-Fix...Nvlddmkm-Error/
My PC has been running for 2 days now. I only put the top fix in for now. Feel happier I have more options if need be though.
Inserted from <http://forum-archive.developer.nvidia.com/index.php?showtopic=5331&st=40>
It worked for me

Nokia Ovi Suite has lost connection with your devi...

5 months has passed and many hours on the phone to Nokia. The phone has been completely reset /reboot by Nokia time and time again and still the phone gets this message when trying to update software..."Nokia Ovi Suite has lost connection with your device"....We were optimistic that the software upgrade would solve the other problems we are having with all the Nokia phones at work. They are all E52's

Having the same issue currently with an E72 software version is 054.005.266.02 and Ovi Suite 3.1.1.80
Actually I had connection lost all the time with all previous versions of Ovi Suite too... it has never been reliable.
Using original Nokia USB cable, connected securely. Tried different PCs, different USB ports, same issue.
Just now I'm trying software update and it looses connection during the backup process all the time... very disappointing. Screenshot attached if anybody is interested.
Attachments:
nokia_conn_lost.jpg ‏40 KB

E5: Ovi Suite has lost connection with your device...

I am trying to update the software on my E5 using OVI suite but I keep getting an error during the install phase (after backup). The following error and instructions are displayed in the OVI suite window but makes no difference when I follow these instructions (just end up back with the same error).
"Nokia Ovi Suite has lost connection with your device. Follow these steps to help reconnect your device:
1. Remove USB cable from your device.
2. Restart the device (turn off and on again).
3. Re-insert the USB cable.
4. Click 'Ok' below to continue updating."
Current E5 software version is 042.007.
I am trying to update to E5 software v. 043.115
Any ideas?

Yep having the same issue. Just got a replacement handset due to the random restarting issue, soon after setting up the new handset I get a message on phone saying software update is available. Both OVI suite and Nokia software updater say version 43.115 is available (about 200mb in size), I currently have the same version as you 42.007. It claims to do a lot of improvements to the handset. The update downloads fine but when it comes to installing I keep getting the same issue. Phone simply will not restart automatically and the update restarts then fails at the same point over and over. Had the same problem with my previous handset.
I spoke with my network provider to see if it was an issue with the handset needing firmware specific to them but they said no it is an issue with the firmware itself and has been happening to everyone since its release!!! They said I should not download it until Nokia has resolved the issues with it. But how do I know when that will happen as I cannot find anything put out by Nokia stating there is an issue or anywhere on web forums saying there is actually a problem.

Disk Utitlity has "Lost Connection" with Disk Management tool"

[ Edited by Apple Discussions Moderator; please start a new topic about your technical issue. ]
Running OSX10.3.8
I installed:
"iTunes" (6.0.2)
"iPod Updater 2005-11-17" ((null))
"iChat Update" (2.1)
Went to repair disk permissions
I get this error:
Disk Utitlity has "Lost Connection" with Disk Management tool" Please quit Disk Utility.
then it says quitting Disk Utility may render the disk useless. Stopping the scan just gives a "stopped by User" red text message in the DU screen.
Had to Quit. No other way out.
Now it will not repair "or" verify Disk permissions at all.
What to do?
Powermac G4 1.25ghz, OS9/OSX Mac OS X (10.3.8)

Getting the same results booting off of the install CD. I even ran fsck -y after a soft boot(command S). Note I also installed the iPod updater and iChat update.
I'm getting a crash log that has to do with DiskManagement
Path: /System/Library/PrivateFrameworks/DiskManagement.framework/Resources/DiskManage mentTool
I tossed the pref file for Disk utility and tried to locate a pref for the Disk Management but nada...
Is there a prefs file that needs to be tossed?
Anyone do a recent Onyx Maintainence cleaning?
Is there a way to do an iTunes Uninstal and reinstall a previous version?
Powermac G4 1.25ghz, OS9/OSX Mac OS X (10.3.8)
Powermac G4 1.25ghz, OS9/OSX Mac OS X (10.3.8)

Repeated lost connections when using WRT54g

Hello everyone.
I have a Lynksys WRT54g v5 and a cable modem, my ISP is Virgin Mobile. Every half an hour or so my internet connection is lost and can only be regained by reseting my modem by turning it on and off. The lost connections appear to occur more frequently when the traffic is heavier. The interuptions occur even when I only have one wired PC connection.
If I connect the PC directly to the modem the connection works fine.
I have already installed the latest firmware, reset to factory settings, tried a MAC address clone as suggested in another thread but nothing has helped.
Is there anything I can try or should I just bin the router?
Thanks for your help!

Version 5 and 6 of this router are of a terrible design. No amount of tweaking, reconfiguration or firmware upgrades will likely help with the disconnect problem. Earlier versions are of a much better design. I had disconnect problems with my version 6 router for over two month which could not be resolved by many attempts through Linksys tech-support. Even replacing it with 2 more version 6 routers did not resolve the disconnect problems which occured 3 or more times a day.
After I changed to a version 3 of the WRT54G the disconnect problem was instantly cured. Version 4 and below or WRT54GL ( which is really a resurrected version4)should work fine.

How to fix lost connections to original high-resolution pictures in iPhoto and how to import an iPhoto Book from one iPhoto library to another

Hi there,
I am using a MBP Pro with 8 GB cache and 1 TB HDD from beginning of 2011 with OS X Yosemite and iPhoto version 9.6 (910.29).
I created an iPhoto Book to print which contains my best pictures of 2013 and 2014. Then I got an error message when I wanted to print the book, saying (translated from German):
Book could not be created.
With photo p233432343.jpg there was an error. The original version of that photo with full resolution could not be found or is damaged. Please replace the photo or delete it from your book.
When I enquired further, I found out, that many, many pictures in my iPhoto library have that problem - only the thumbnail picture is found by iPhoto, but not the one with the high resolution. When looking at the photos in detail one sees that they are not sharp because obviously the photo book only refers to the thumbnail. When I went into the iPhoto Library using Finder, I saw that the original high res photos are still there. As there are an estimated 3000 photos with a lost connection (some still have, it but about 1/2 of my photos don´t), it does not make sense to import those photos manually. This photo book is just the tip of the iceberg, so to say.
Then I looked for solutions in some forums. I had two lPhoto libraries, one on my HDD (120GB) and one on an external HDD (175GB). Assuming there might be problems, I have deleted (moved) the one on my HDD, because the "right one" is the one on my external HDD and started iPHoto again using the alt key. But that did not work either.
I then tried to repair my iPhoto library using iPhoto Library Manager, and merged and rebuilt libraries. The library that came out was crap - all folders that had lost connections to the high resolution pictures now have zero photos in it. Also it is lacking the projects, including the photo book I created.
Then I went to find out if there is a way to import the iphoto book project from the old, corrupt library into the new, repaired library but could not find anything. It can only be exported as a file structure or website. As the file structure is missing the high res pictures, that does not even solve the "little" problem of the photobook.
I would REALLY appreciate your help on the two questions:
1- Can you advise what I need to to do to to get the connection to the high resolution photos established again ? As it is more than 3000 photos, I use an automated way of reestablishing that connection. Probably an answer to this question would make question 2 irrelevant.
2- Do you know if there is a way to export and import a book project created in iPhoto from one library to another ?

1 - Select the thumbnail of one of the problem photos and use the File ➙ Reveal in Finder ➙ Original menu option. This will take you to the folder containing the original file with that file selected by the Finder.
You can also use Find Any File to search for that file (get the file name from the Info pane in iPhoto). You will find the thumbnail version and maybe an edited version also. Made sure what is found is the large, original version and note were it's located. Search all of your drives with FAF just in case.
If you don't fine the full sized version then the only recourse is to use a file recovery application like SubrosaSoft FileSalvage on your drives to see if any of your full sized photos can be recovered. If you find enough files to make the purchase of the software worthwhile buy it and recover the files. However, since it may have been quite a while since you discovered the missing originals it seems unlikely you'll be able to recover any due to being overwritten.
2 - book projects are just entries in the library databases and can't be exported to another library.

CM1312 NFP: WIndows 7: USB Error message ~"Lost Connection"

With the 1312 connected to my Windwos 7 desktop, periodically Windows gives an error message that indicates that it has lost connection to the printer. Unplugging and replugging the USB cable fixes the problem. Otherwise the print & scan functions work perfectly. Symptomatically it appears as if the printer goes to sleep and stops responding to whatever "keep alive" messages Windows might be sending. Is there a setting in the printer, in Windows or in the printer driver software that can prevent this message?
BTW, the other way to work around this problem is to just access the printer via the Ethernet but the scan funciton is not accessible via the network (an unfortunate limitation).

aluniewski,
I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at http://h30499.www3.hp.com/hpeb/ .
I hope this helps.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Personal File Sharing: Lost Connection

I'm trying to use my new miniStack external HD attached via Firewire to my Mac mini as a pseudo network drive. In other words, I want that drive available to my mini and my two iBooks. If I can get that working, I'd like it available to my XP box as well.
I have wireless internet via an Airport Express and cable modem throughout the house. All four computers are attached via wireless cards.
I've turned on personal file sharing on the mini using my administrator log in. I've also activated AppleTalk via the Airport settings in the Network preference settings.
I've also activated AppleTalk on my iBook and turned on personal file sharing.
All my Macs are running the latest version of OS X (10.4.7).
I restarted both machines after making the above setting selections. I then used the Finder on my iBook to search for the mini. I clicked on the Network icon, found 'servers', 'library', and the following folders: "home" which has my XP box readily accessible, "My Network" and "Workgroup". Each of these last has an icon for my mini.
When I double click on my Mini, it shows me all volumes on it, including my miniStack. I select one to connect to and get a beach ball followed by an error message saying "Server Connection Interupted: miniStack" and a single button marked 'disconnect'.
After I press the disconnect button (my only choice) I notice that personal file sharing on my mini is now turned off.
This exact same thing happens when I try to access the native internal HD on my mini so it isn't just the external stack that's the problem.
I've searched high and low through the fora here and can't find anything addressing this.
Does anyone have any idea what I'm doing wrong?
Thanks and take care,
Jeff

After much trial and error, I finally resorted to doing a Archive and Install on my mini. After doing so, everything works great. I still have no clue what the problem was but I now have no interest in finding out since it's working great.
Of note, the lost connection problem was unidirectional. I had no difficulties logging onto and accessing anything on either of my iBooks from my mini. Just the other way around.
Take care,
Jeff

I just lost all my contacts on the ipod2 ...how do I get them back? They just disappeared while I was typing in a new contact.

I just lost all my contacts on the ipod2 ...how do I get them back? They just disappeared while I was typing in a new contact. Help!!

joephilipose,
If the contacts are still in Address Book on your computer, but just not on the phone, you can tell iTunes to force replace the contacts on your phone with those from your computer. You can do this by going into the Info tab when your iPhone is connected, and checking the Contacts box under the Advanced section at the bottom of the page.
You may also want to backup your Address Book information as well. It's a good idea to make periodic backups of your contact and calendar information in case information accidentally gets deleted or changed. You can find out how to backup your Address Book data here:
http://docs.info.apple.com/article.html?path=AddressBook/4.0/en/ad961.html
To backup your iCal information, follow the steps in this article:
http://docs.info.apple.com/article.html?path=iCal/3.0/en/9889.html
Hope this helps,
Jennifer B.

Mysql_connect "Lost connection to MySQL..." error 61

A web developer is getting this error on a test web server of ours that is running 10.5.7 Server.
"Warning: mysql_connect() function.mysql-connect: Lost connection to MySQL server at 'reading initial communication packet', system error: 61 in..."
I've seen other postings online for this error suggesting that the line containing 'bind-address 127.0.0.1' be commented out within /etc/my.conf... but this line doesn't exists on my installation.
MySQL and php have been working well for other databases and developers. This is a newly created database.
Has anyone else seen this error and found a fix?
Thanks!

This is more than likely a firewall problem on your users end. I just ran into this when moving my servers to a colocation. Everything was fine until i tried to connect to an outside database from the machines behind the new firewall. was set to allow 3306 in, but not out. And would connect without issues to localhost:/var/mysql/mysql.sock .
from the machine trying to connect from try
shell> telnet <servername> 3306
should be able to login. if refused, then port is closed.
-------

Suddenly lost connection to my wifi and my phone can't find it again?

I was just using my iphone 4s normally and it suddenly lost connection to my home's wifi. I have been trying for hours, reset the wifi modem and turned it on and off, put my phone through recovery mode- the whole lot. Please help!!!

Howdy whitneyavon,
It sounds like you are unable to either connect to, or see your home Wi-Fi network. I would first, update your router, then reset your network settings. Assuming you restored from a backup, my thought is that the backed up network settings may need to be refreshed:
Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
From: iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Thank you for using Apple Support Communities.
Regards,
Sterling

My wrt300n just lost connection

Similar Messages

Maybe you are looking for