My X301 with solid state Hard disk lost all data

Hello all people, excuse my poor english i try to explain my problem.
1.- I have a Lenovo x301 (type 2776-TMU) with a 128 Gygabites solid state hard disk (Samsung MMCQE28G8MUP-0VAL1)
2-The sympton is: Lost all data of the hard disk and apears 0 partitions and 0 bytes used.
3.- I run all type of diagnostics and all pass OK.
4. I restore windows,aplications etc. and all work fine, but in any random time, the hard disk lost all info and another time apear 0 Partition and 0 bytes used.
5. I try to install, bios, firmware or any update of the lenovo web, and no resolve my problem.
6.- In a last chance install via dvd a fresh instalation with oem windows 7, and present the same sympton of point 4.
7.- I change parameters on the bios setup of the SATA interface (ochi or compatible) with the identical result of the 4 point.
How you understand, i have a big problem and desesperate, but i not sure if my hard disk is of the problem, or the mother board, any firmware, etc.
Any have idea in how attack o determine exactly the origen of my problem?
Thanks and regards all people.
atn, Miguel Angel Borbolla Bonomi
Moderator note; e-mail address removed to stop the spambots getting it

Sounds like a faulty SSD. Return for warranty repair/replacement.
T61p, T400
formerly x23, x40

Similar Messages

Which Solid State Hard Disk for Satellite Pro L670?

I have a Satellite Pro L670 which I want to configure for presentation purposes and have to re-load the operating system anyway.
Rather than over-write the existing disk, I thought it would be better to get a second one to fit instead.
Replacing the current (old-fashioned) spinning disk with a solid state one seems to me the best way to go.
Has anyone else fitted a solid state hard disk to a Satellite Pro?
For budget reasons I am planning to go for a 120GB capacity which will be enough.
However I have yet to find out from Toshiba what they might recommend. Anyone else yet gone this route?

Hi
Theoretically any SATA SSD drive should be compatible because the notebook supports an SATA controller.
But in some cases it could be possible that an SSD drive would not be handled properly. In such cases the SDD drive manufacturers provides different firmware updates
So before purchasing an SSD drive check the support pages of SSD drive manufacturers for further details maybe an firmware update would be available

Lightroom and solid state hard disks

I'm looking to speed up Lightroom as much as possible within reason (version 3 on a Mac) and one possibility that occurred to me is to put Lightroom and it's catalog on a somewhat smaller 80-120 GB (and therefore less expensive) solid state hard disk. I'm wondering if Lightroom interacts with the system enough that I wouldn't gain much? I would think that I would get a pretty good speed bump...

Pete Marshall says:
SSD's are great for the OS and apps. They may not be so good for the catalog itself as write speeds are not good. If I was you I would get a small SSD to use as the boot drive and put the catalog and files on seprate fast traditional hard drives.
Write and read speed of currently available SSDs blow away hard disk drives in any configuration. Look here:
http://www.harddrivebenchmark.net/high_end_drives.html
SSDs are more expensive per GB than HDDs, but you don't need a large 1TB+ drive to increase system performance! I work with Intel who is one of the top SSD manufacturers and R&D companies. Intel is working with Micron on joint program to reduce cost of SSDs. Intel just announced their new SSD 510 series:
Intel SSD 510 Specification
SATA 6Gb/s Sustained Bandwidth Performance
(Iometer* Queue Depth 32)
— 250 GB:
Sequential Read: Up to 500 MB/s
Sequential Write: Up to 315 MB/s
— 120 GB:
Sequential Read: Up to 450 MB/s
Sequential Write: Up to 210 MB/s
Compared to a high performance HDD:
WD Caviar Black
Samsung HD103UJ
HDTach
Burst (MB/s)
232.6
204.5
Random Access (ms)
12.1
13.7
Average Read (MB/s)
89.5
96.8
Average Write (MB/s)
79.9
84.4
I have no experience running LR on SSD, but putting your LR catalog, RAW cache, and preview files on an SSD should provide a real performance boost.

2011 MACBOOK PRO WITH SOLID STATE HARD DRIVE.

Hello everyone. I would like to know is it worth going with the 512 solid state hard drive or the 750 at 5400 rpm or 500 at 7200 rpm. My use is for Audio programs such as Serato, Logic and Protools. I would like to know if anyone has the solid state and how you like speed of the computer. Basically is it worth the 1100.00 extra.

No one probably wants to touch this because it really is about how high end a user you can afford to be. I suspect your audio programs will work fine with a 7200 rpm hard drive, depending perhaps on file sizes. I did buy a 512gb ssd and put it in my 2010 mbp. It has read and write speeds comparable to what Mac promises with the in-house drives (maybe a little faster). If you can afford an ssd you would never go back to a hard-drive. It removes a performance bottleneck that will always be there to some degree with a regular hard-drive. 512gb ssd's are a luxury at this point. Your call.

Disk Drive Full. Whats the best way to transfer operating system to larger non solid state hard drive .

Heres the Lowdown,
I have a Desktop that has a 250 G Solid state hard drive , and a secondary 750 G Hard drive.
My OS is installed on the solid state , and also a lot of my audio software which needs to also be on the same disk drive as the operating system ;
Problem is I've run out of room and continually get DISK FULL error messages , which stop me from doing any real time audio tracking and recording.
I've backed up all files to an airport drive ( I'm a bit paranoid about losing vital info) .
Is there a way to reinstall the OS onto the second larger drive and just transfer the remaining software across
Will I have to reinstall all previous versions of software if I do this?
Will The processing slow down if the OS is run on the Standard drive rather than the Solid State drive ?
Last time I tried to clear some space on the OS drive I accidentally deleted vital information, so I wanna make sure I do this properly.
Any advice would be much appreciated.

Carbon Copy Cloner (1 Month Demo with full capabilities). Because CCC also has the ability to transfer your Recovery Partition
SuperDuper (Free for a full clone). Recovery partition will not be transferred
Applications -> Utilities -> Disk Utility -> Restore (from SSD to 750 hard disk). Recovery partition will not be transferred.
Or install the OS on the 750 hard disk (with will install a recovery partition), then use migration assistant to move your files over. Or you could then use one of the above utilities to overwrite the just installed OS without messing with the recovery partition.

I want to change screenshot location from my Solid State hard drive with OSX on it, to my 2nd storage hard drive, how do I do this?

I want to change screenshot location from my Solid State hard drive with OSX on it, to my 2nd storage hard drive, how do I do this?
I am aware of "defaults write com.apple.screencapture *location*" but I want to change the location to my 2nd drive which doesn't have OSX on it... everytime I've tried to insert MacintoshHD2 in there it just doesn't work... any tips?

I'm having the same problem. I've entered the following path in terminal:
"defaults write.com.apple.screencapture location /Volumes/Macintosh HD 2/[my username]/Downloads"
But it's not working. It keeps going to the SSD Downloads folder.
What am I doing wrong?

My 3 apple products, an imac, a macbook air and a macbook lost their contact with their external hard disks. They were LaCie make. And every time I turn my laptops, I find the positions of the keys on their keyboards changed. Why is Apple silent?

After the latest apple IOS upgrade my 3 apple products, an imac, a macbook air and a macbook, lost their contact with their external hard disks. They were LaCie make. And every time I turn my laptops, I find the positions of the keys on their keyboards changed. Why is Apple silent? There are so many people complaining about this issue and expecting Apple to correct this issue that they have created.

Probably because it's not an Apple issue. I have Lacie EHD's connected to my MBAir and iMac, all work perfectly on Mavericks. In addition I don't have any keyboard issues on any of my Apple products. BTW IOS is only for IOS devices such as iPads, iPods and iPhones, Macs use OS X. The two OS's are seperate products designed to run on seperate products.

Solid State Hard Drive Replacement For HP ENVY TouchSmart 15-j053cl?

Hello there,
I want to swap out my current 1TB harddrive from my year-and-a-half old HP ENVY with a 500 GB solid state harddrive that I just purchased from Amazon.
Two questions:
1) Is this solid state harddrive compatiable with my computer (specs below)?
2) I want to reinstall windows onto the solid state harddrive after I install it (assuming its compatable). How can I go about putting Windows 8 on a bootable usb drive to do this? The computer does not have an optical drive and I don't have an external optical drive, so installing Windows via bootable usb is my only option.
I'm aware I can "clone" my PC onto the external harddrive if I wish, but I'd rather do a clean install if I can.
Computer Specs:
HP ENVY TouchSmart 15-j053cl
Product: E0K05UA#ABA
Solid State Hard Drive Specs:
Samsung 850 EVO 500GB 2.5-Inch SATA III Internal SSD (MZ-75E500B/AM)
http://www.amazon.com/gp/product/B00OBRE5UE/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Please let me know any advice you may have. Also, please feel free to ask any questions - hopefully I provided enough details.

Windows 8.1 has a built-in tool to make a recovery usb drive:
http://windows.microsoft.com/en-us/windows-8/create-usb-recovery-drive
The HP Backup and Recovery app can also do it. This is a factory clean install image and any data and programs you have added will be lost. If you have an external hard drive you can also do a backup with Windows File History. Then, add the backed up files to the factory install. You can also use File History to make a system image type backup and restore it to the new drive using a repair disk but this is virtually the same as a clone, which you said you do not want.
Manual
Your service manual linked above. See page 47.
The Evo 850 is the best SSD on the market in my humble opinion and will work just fine for you.
If this is "the Answer" please click "Accept as Solution" to help others find it.

Recounting My Successful Experience Upgrading My Solid State Hard Drive

I just successfully upgraded my solid state hard drive from
60 gigabytes to 256 ; the machine is a Lenovo T400s - while the upgrade is
still fairly fresh, I thought I’d share my experience – maybe someone else will
benefit – most of what I’m about to relay was provided by Zoltanthegypsy and
GMAC-R60 – I thank them again for their advice - but I will try to add some
additional thoughts based on my experience – for the most part I was able to
use the tools provided by Lenovo – my original hard drive had 3 partitions, S
(system), C ( windows + my programs & data), & Q ( Lenovo stuff like
backup and restore, the factory copy, etc.) :
Create a “factory state” copy of the machine to
DVD or CD soon after purchase – I say soon after purchase because it appears that
a minimum amount of hard disk space is required – my 60 gig was almost full and
I got a message that there wasn’t enough space – I can still make the copy but
I’ll have to move some things off temporarily – this step isn’t really related
to the upgrade but it is a good idea – Start/Lenovo ThinkVantage Tools and you’ll see
the option – and as Zoltanthegypsy has pointed out you will most likely not be
able to do this from the new hard drive after the restore operation covered
below – I haven’t proven this out but I do know that my Q space on the new
drive is smaller than before – something was lost and it’s most likely the
factory state – and so keep the old hard drive long enough to make that factory
state copy to DVD or CD.
The next step was a full backup to a Lenovo
external hard drive – it came with one partition - the external that I got from
Lenovo has a small keypad and is password enabled – this fact will come into
play further on – as GMAC-R60 noted a pop-up will appear giving the option to
create rescue media – you want to select this option so that the external will be
bootable.
When the backup is complete you want to swap hard
drives making sure to first unplug & remove the battery .
There may be other ways to do this next step but
here’s what I did – I powered on the machine and let it go through what
appeared to be a BIOS routine – note that my external was attached to the
laptop but it wasn’t activated by keying in the password – after the BIOS
routine was finished I activated the external by typing in the password and then
did a Control/Alt/Delete – the machine restarted and booted from the external –
with hindsight I probably could have connected & activated the external
before powering on but the instructions that came with the external suggested
something different which didn’t work for me .
I was now able to go into rescue and recovery
and do a complete restore to the new drive – but to my surprise the extra space
that I bought with the new drive ended up all in the Q partition – and Windows
Disk Management didn’t enable me to reallocate the space to C.
And so I purchased Disk Director 11 Home by
Acronis – a $50.00 investment in a tool that I’ll probably never use again but
I’m now able to use an $800 solid state drive rather than trying to recoup some
money via Ebay -– within minutes I was able to reclaim the space and I now have
enough C space to last the lifetime of the laptop – especially since all
pictures go on a stick & my demographic isn’t into video games .
One useful piece of information that I got from
a user on the Acronis forum was that all of the Lenovo tools like rescue and
recovery, etc. are available for download from the Lenovo website – and so if worse
came to worse I could have deleted that Q partition, stretched C using Windows
Disk Management , and then downloaded the Lenovo tools into C.
One thing I’d like to learn to do would be to
perform all the steps outlined above but without using the Lenovo tools – using
Windows 7 tools instead but not having a Windows CD , i.e. how do you boot

It went something like this:
(On the stock drive)
Plugged in a blank USB HDD, and a blank USB flash drive.
- HDD formatted in NTFS, flash drive in FAT16.
Ran the recovery media creator.
- Created bootable media on flash drive, and put the recovery image on the HDD.
Once done, shutdown, removed the battery, swapped the drive for a 500GB Scorpio Black (freshly NTFS quick-formatted). USB HDD and flash drive were still attached.
Booted, and used F12 to select the flash drive for booting.
It booted into the Windows Recovery Environment and I chose the Lenovo restore factory image option at the bottom of the list.
From there on out, I just clicked through the wizard, and it restored.
Upon finishing, I unplugged all of the external media, and had it restart. It then booted into OOBE as expected.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

I am replacing my existing SATA hard drive to a Solid State hard drive and want to image the drive, is this possible?

I am replacing my existing 320 GB SATA hard drive that clicks and makes weird noises to a Solid State hard drive and want to image the drive, is this possible? I then want to replace the DVD with a secondary large drive for storage.
So I am looking for any "gotchas" that I may be unaware of.
Thanks!

Put the Old drive in an external notebook drive enclosure. Install the SSD in your computer. Boot from your Old drive's Recovery HD:
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Clone Lion/Mountain Lion using Restore Option of Disk Utility
     1. Select Disk Utility from the main menu then press the Continue
         button.
     2. Select the destination volume from the left side list.
     3. Click on the Restore tab in the DU main window.
     4. Select the destination volume from the left side list and drag it
         to the Destination entry field.
     5. Select the source volume from the left side list and drag it to
         the Source entry field.
     6. Double-check you got it right, then click on the Restore button.
Destination means the New SSD. Source means the external Old hard drive.
Set the new Startup Disk to the SSD and restart the computer.
This process clones both your old OS X volume and the Recovery HD volume to the SSD. You can use a similar process to clone the SSD to the new hard drive you will install.

T400s solid state hard drive already full

I have a newly-purchased t400s with a 120gb solid state hard drive. The drive is already almost full, and I have only uploaded about 35gb of data from my old computer. How is this possible? Are there specific programs that are eating up my storage space? Thanks.
Moderator edit: Added detail to subject.

Is it a Lenovo-provided installation or your own clean install?
How long have you had it? is it doing those ridiculous R&R automatic backups to itself?
What's the partitioning layout shown in disk management? Service partition? Recovery partition?
From the above you can tell I have no idea what's going on...
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Solid-state hard drive questions....

Hi, I'm going to get a new Macbook Pro soon to replace my archaic 17" wobbley screened Powerbook and I'm having some dilemmas about picking the hard drive. So heres a few solid-state questions I was hoping you could answer:
How much faster is solid state than disk (disc?), for example I run Flash and Photoshop alot. If a go for 8gb of ram and 3.somthing processor, will there be a noticeable difference in the speed of these apps opening/running if the hard drive is solid state?
and...
If I go for normal hard disk now, is it possible to upgrade the hard drive at a later date (doing it myself or through Apple) to a solid one?
It's an extra 600 quid that I could be spending on crisps, so is it worth the money?

While I can't comment on the speed I can comment on changing the internal drive. In short it's a 10-15 minute process. My recommendation would be to start with a traditional HD and see if it's performance is adequate before considering an upgrade. If not as mentioned the upgrade is extremely easy. In fact here is a video that shows it.

Solid state hard drive space problem

hello to all,
my friend owns the macbook air, we bought the one with the 64GB solid state hard drive.... we checked all the folders within the user folder (application, library, music etc.) and they total a 12GB or so of space! but it says the hard drive is full and he has 1GB left..... what might be the problem???

You may wish to try this application: Omni Disk Sweeper
http://www.omnigroup.com/applications/omnidisksweeper/
It'll scan the HD for you and give a break down as to where things are and hopefully assist in resolving the issue.
At least then you can determine if the number it returns equals the number you expected. Also, is your friend syncing a local copy of his iDisk? Or a FileVault user?

Solid State Hard Drive for HP Pavilion Elite m9040n

I seriously considering replacing my "C" drive with a SSD. I've upgraded to 8 G memory, replaced the video card to a Galaxy GT 610. I'm still running MS Vista Home Premium. i'm looking to upgrade to MS 8.1 and office 365. I want a faster boot time and current OS. I DONOT play "Games".
Can anyone recommend a Solid State Hard Drive?
Thank You
This question was solved.
View Solution.

I am partial to Samsung SSD's. I have installed one in my HP 810-135qe. Here is an EVO 840 - 250 GB:
http://www.samsung.com/us/computer/memory-storage/MZ-7TE250BW
You can use Samsung's Data Migration tool to clone your HDD to the SSD.
You can contact Samsung's Customer Support to make certain that it will work in your computer.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Solid state hard drive for X100e

Can one replace the hard drive that comes with the x100e with a solid state drive? If so how would one go about doing it?
Is there a Thinkpad with a solid state hard drive about the same size as the x100e? My only complaint about the x100e is the relatively short battery life and it seems to me that a solid state drive would correct that(?)

Hello,
I have two X100e's that I installed the Kingston 64GB SSD in for family members. The process was not terribly complicated:
• turn the X100e over
• remove the battery
• unscrew the access panel on the bottom
• remove the HDD caddy (I don't recall if it has a screw holding it in)
• remove the HDD from the caddy
• install the SSD to the caddy
• reinsert the HDD caddy
• replace the access panel on the bottom
• reinstall the battery
At this point I plugged the AC adapter back in, connected a DVD±RW disc drive via USB and installed Microsoft Windows 7 to the SSD from the recovery discs I purchased from Lenovo.
The Hardware Maintenance Manual for the X100e, which explains how to replace parts on the unit, has excellent diagrams explaining how to swap out the disk drive. It can be found online here. There are also videos here on the Lenovo Service and Training web site which might be of use.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

My X301 with solid state Hard disk lost all data

Similar Messages

Maybe you are looking for