My xperia z1 wont turn on at all

Hello to everybody yesterday i recived my xperia z1 i started it up and it was working fine,after the installation of the latest update the phone,had started to restarting by itself and was not able to boot up,and i did the method with power button and volum up button,and its worked,and i put it to charge for 10 hours,later i used the phone i downloaded a game and after the installation i lunched the game,and again the xperia shut down,and now i can not power it on,and i did every method,but i dont understand i used this phone for only one hour what is the problem,its not working at all and nothing neither led light neither vibrate when i push the power button please help me!!

Try performing a system repair using PC Companion as this will often fix issues - This will factory reset your phone and erase all data
Switch off your phone and unplug from Pc (Hold volume up and power for around 10 seconds)
Start PC Companion and select Support zone then Update my phone/tablet then in Blue Repair my phone/tablet and follow the on screen instructions - When prompted connect your phone still switched off holding volume down or back button - This should start the repair or reformat process
If you are using Windows 8/8.1 or a 64bit operating system then adjust the settings for PC Companion and run in compatibility mode and chose Windows 7 or XP
For a successful technology, reality must take precedence over public relations, for Nature cannot be fooled.   Richard P. Feynman

Similar Messages

  • My i pod classic shows a sad face on the screen and wont turn on at all will i need to sent it off to get repaired or how can i fix it thanks shiv

    my i pod classic shows a sad face on the screen and wont turn on at all > will i need to sent it off to get repaired or how can i fix it thanks shiv

    i have this same issue! have you figured out what to do?

  • Was trying to upload a video through facebook then phone shutdown and wont turn on at all even if plugged

    for my iphone4 i was trying to upload a video through facebook then phone shutdown and wont turn on at all even if plugged

    Try resetting it:
    Press the sleep/wake button & home button at the same time, keep pressing until you see the Apple logo, then release.

  • Ipod has a sad face with exclamation point and now it wont turn on at all!

    my ipod was fine and then when i turned it on it had an ipod with a sad face with an exclamation point but now it wont turn on at all! please give me any suggestiions . thanks so much!

    See these troubleshooting articles.
    My iPod is sad.
    What does this picture on my iPod mean?
    PC doesn't recognize the iPod is connected.
    When restoring the iPod, it's useful to put into disk mode first.
    Putting iPod into disk mode.
    The sad iPod icon is usually indicative of a hard drive problem, and if none of the above help, it may need service.

  • HT1349 my iphone 4 wont turn on at all

    my iphone 4 wont turn on at all. how do i fix this?

    Reset it by pressing and holding the home and power buttons until the white Apple logo appears.

  • HT201210 iphone 4 wont turn on at all.

    my iphone 4 switched itself off and now it wont turn on at all any help please !!!!

    Hi there coleeva!
    I have an article for you that can help walk you through the troubleshooting steps for the issue you are seeing with your iPhone. The article can be found right here:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    This article has information on a plethora of issues regarding your iPhone, so for your convenience, I will highlight the relevant part to your issue below:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 15 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks for using the Apple Support Communities!
    Cheers,
    Braden

  • And wont turn on at all. please help thanks.

    my ipod touch wont charge when i plug it into the computer or any source off power and wont turn on at all. anyone got any ideas of how i could maybe fix it. thanks.

    Have you tried using a different connecting cable?  Sometimes those or their connectors fail.
    If that doesn't work, have you tried connecting to iTunes and see if it is recognized?
    If not, might be time to visit an Apple Retail genius bar and have it checked out.
    How old is the iPod?

  • My curve wont turn on at all! *please help!*

    i got my blackberry curve 8520 over a year ago, ive had no problems up to now when it wont turn on at all. i have searched forums and tried plugging it into my charger without the battery and leaving it for 10 seconds then putting my battery in, but nothing! i even bought a new battery for it and charged it for 12 hours but still nothing. and help is MUCH appreciated!

    Hi leedslad,
    Welcome to BlackBerry Support Community Forums.
    Is your BlackBerry detected by your Desktop Manager when connected?
    If so, try backing it up and clean reloading the device software. A backup is recommended as this will remove any data from the device. http://bbry.lv/bpv7DT If it doesn't connect, try forcing a clean reload of the software using this article. http://bbry.lv/dl7hmf
    -FS
    Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.
    Click Solution? for posts that have solved your issue(s)!

  • My ipod touch wont turn on at all even when i connect it to my computer

    So my ipod touch wont turn on at all even when i connect it to my computer! it was working fine then outta no where it wouldnt wanna turn back on. i tryed resetting but it doesn't do anything. Also when i put it on the charger it seems to get pretty hot...is the normal? help please...

    There are two different causes of this, either it has been overheated, or the iPod just crashed.  If it crashed, there is one simple step to fixing it.  Letting the battery die.  Do not connect to a charger port, or the device may get overheated, and need to be replaced.  Once it dies, it normally will show the icon, that is needs to be charged. Once you charge it back up, it should go back to normal.  If this doesn't help, then contact apple to the nearest store about getting a replacement.

  • My ipod touch 4th generation will not turn on and i dont know why. It just wont turn on at all. I try to press all of the buttons and hold them down for awhile and it still wont turn on. This all happened after i sent a video that was 1 minute long. HELP!

    Im having issues! Its terrible. I press and hold the buttons.....it wont turn on. i need help because i dont want it to crash and lose all of my information on this ipod. I NEED HELP! WHATEVER ADVICE YOU HAVE WILL BE HELPFUL!

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • My ipod mini wont turn on at all no matter what i try

    I've tried toggling the hold button while holding down the menu and select buttons, and i've tried a few other things that i have been told to in the situation that my ipod wont turn on, but none of them will work. right now it's hooked up to the usb cable on my computer, and it has been for the last couple days. i think all this might be because ive been too lazy to click eject before i unhook it a couple of times before, but i dont know.

    I've tried toggling the hold button while holding down the menu and select buttons
    It seems you are not performing the reset correctly. Don't worry about the hold switch...just press and hold menu and select simultaneously for about 6 seconds until you see the Apple logo appear. If you have an AC adapter, plug the iPod into the wall socket using this and then try the reset.
    i think all this might be because ive been too lazy to click eject before i unhook it
    Bad idea! You should always eject it properly or you risk corrupting the hard drive...it would be a shame to have to fork out for another iPod just because of laziness!

  • Sony xperia z1 wont turn on completly after rebuild

    Hi! I really need your help guys!I have a Xperia Z1. The other day i decided to change the screen and the back part (glass) and the frame, so almost the whole phone. Now when im done it wont turn on, but when i put the charger on the screen lights up with the sony logo, then it shows me the battery logo and then it turns off. I cant do anything. No hard reset, nothing. I cant connect it to PC companion because it cant connect. What is wrong?

    As you decided to do it yourself, you may have done something wrong while assembling the phone. I suggest that you send it to the nearest repair center:https://talk.sonymobile.com/t5/FAQ/How-to-get-your-Sony-Xperia-product-repaired/m-p/991374#U991374

  • Xperia c1905 Wont turn on

    Sony Xperia M C1905 wont turn on! My sony xperia m C1905 Wont turn on, i plug it into a wall charger and goes to battery screen then turns straight off, amber led stays on, i have tried to link it up to pc companion and it wont recognize my phone, i have tried holding power button and volume buttons but still does not turn on and i can not get my IMEI number to send it in to get repaired.  Someone please help.

    Hi @iiaMMartyn Connect your device to a wall charger and then press and hold power & volume up for more than 10 seconds. Let it charge for 2
    to 3 hours, even if it doesn't seem to be charging. I would also try to get another battery from a same device to replace, and see if it turns on after charging.. I hope can be useful. Best Regards.

  • Bondi Blue iMac 266 wont turn on at all.

    OK, WELLLLLLL, i know you guys probably see this kind of thing everyday. i looked around the forum through all those "imac wont start" pages and none help. mine seems to be a different problem. ill try to give as much info as possible.
    ok, i push the main power button, it chimes, HD spins up, everything seems just fine then click click click, and the whole thing goes off (no it doesnt boot up and monitor is just off, the whole thing goes off). if i remember correctly, the power light never turned green, and if it did it was for a short time. after it does this, pressing the power button does NOTHING, no noise at all.
    i have 2 other identical macs so ive done a little experimenting (the other two work flawlessly) first i tried just swapping the computer out (not the board, the whole slide out thing, cdrom, hd logic board and all) that didnt work. while i had it out, i tried the computer part from the problem mac, in the other case (the one i knew worked) it worked, but when i installed some updates and restarted, it wouldnt come back on. it did the same as the other the power button did nothing, no noise whatsoever.
    so im confused as ever. seems like both parts are broken haha, the crt part AND the computer.
    blah, im gonna fiddle around with it a little more see what i can do.
    any ideas??? (ALSO, it says 10.2 but honestly i have no idea what os this imac has, but im pretty sure its 9.1)
    iMac G3 (CRT) 266 MHz / 512K Cache/32 MB/ 6GB HD/24x CD-ROM/ RAGE PRO / 6MB SGRAM/ modem   Mac OS X (10.2.x)   Bondi Blue/Green W/E it is haha

    ok well just to clarify it a little bit, i just took the board out unhooked it all removed battery memory, etc (not cpu though), put it back in, plugged it back up, hit the power button. it chimes, hard drive spins up, the light is orange the whole time, then right as the light turns solid green i hear a click and the whole thing goes off and wont turn back on. also, i tested the battery and i think its dead. would a dead battery cause all of this????

  • My ipod 5 wont turn on at all and my home button is broken, i tried connecting it to itunes on my computer but nothing works please help!!!

    My ipod 5 gen wont turn on at all

    Try:                                               
    - iOS: Not responding or does not turn on           
    Ignore the reset and when it says place the iPOd in recovery mode
    Place the iPod in recovery mode using one of these programs:
    For PC
    RecBoot: Easy Way to Put iPhone into Recovery Mode
    or
    http://joshuabailey1997.wordpress.com/2010/09/02/recboot-v1-3/
    If necessary:
    Download QTMLClient.dll & iTunesMobileDevice.dll for RecBoot
    and                                           
    RecBoot tip
    RecBoot may have problems on 64X windows, then try:       
    Tenorshare ReiBoot – Enter & Exit iPhone, iPad, iPod Recovery Mode with a Single Click
    For MAC or PC       
    The Firmware Umbrella - TinyUmbrella
    Installs blootware on PC too
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

Maybe you are looking for

  • Error:IDoc cannot be processed: Qualifier not supported.

    Hi experts,                          I got this error when executing the idoc message type: dirdeb basic type : pexr2003 error:Error during creation of internal payment order. IDoc cannot be processed: Qualifier not supported. Thanks Saravanaperumal

  • Shrink the List of File Types in the Save As List

    How to I simplify the list of file types in the Save-As file type list? I use less than six file types. I have no need for most of these. It would be nice to have my top 5 and then the ability to go off-menu if needed for others. Thanks, Drew

  • JavaFX and 3D

    Hi all, I would like to create a custom shape in 3D. But i didn't find the way to create the custom 3d shape. I have seen in the examples, 3D shapes are created by 2D shapes modified. If I want to create a 3D shape should I take 2D shapes, like recta

  • Issues while connecting databases-ORA-12545!

    hi, We have new set of environments ,for which we have faced the firewall rule missing isssue and it gets resolved(able to telnet the ip address now).When we tried to connect those oracle databases(version 11.2.0.3),we are getting ORA-12545: Connect

  • If there is no error in procedure/function, what is  value for SQLCODE..?

    Hi all... If there is no error in procedure/function, what is value for SQLCODE..? I Think, 0 (zero) is the default value for SQLCODE and default value for all other varaibles in PL/SQL is NULL. I am right or wrong...? Thanks in advance, Pal Message