My Zen Micro will not leave the Start Scr

I have had my Micro since last Christmas. I have had no problems up untill yesterday, I went to turn it on, but when i pulled the little on button, it went straight to the open screen, made a really wierd noise then stopped, the light went off, and now it wont do anything, i plugged it into the wall jack and left it untill today when i woke up. I took it off of the charger and it was the same.. on that screen. I plugged it up to my computer but it wont recognize it!!! no matter what buttons i push it just stays the same!!
Someone Help!!!
<3 Steffles

Here's what you can try:
Zen Micro / Zen MicroPhoto
. Make sure that battery is charged.
2. Detach your player from the computer, and ensure that it is turned off.
3. Remove the battery.
4. Move and hold the Power button to the Power On position and re-insert the battery to the Zen Micro. Hold the Power button until the Recovery Mode appears.
5. The following options will be displayed:
* Clean Up (Performs a disk scan on the players hard disk, it will not affect music files)
* Format All (Formats the players hard disk - Note: all contents will be lost)
* Reload Firmware (Reloads the Operating System on the Jukebox)
* Reboot (Reboots the device).

Similar Messages

  • Zen Micro 6GB Frozen to the Starting Scr

    I haven't opened my Zen Micro 6GB about 2 months after I received it and when I try to operate it, it stays frozen to the screen with "Creative, Copyright(c) 2004, Creative Technology Ltd, All Rights Reserved" and stays like that forever.
    I even tried removing the battery, holding the power to on, and placing the battery back in and nothing is happening.
    Can you give me some pointers? Or should I so a warranty exchange?

    tried giving it some more power? It could just be lacking battery....

  • HT201263 None of these answers help my problem.  My ipad will not leave the Apple logo.  I hold both buttons and the screen goes black, then the apple logo immediately pops back up.  I can't do anything because the apple logo just keeps popping back on.

    I haven't been able to find any answers that solve my problem.  My Ipad will not leave the Apple logo.  I hold both buttons and the screen goes black and then the Apple logo immediately pops back up.  I can't get the red slider screen at all.  No matter how many times I hold down both buttons the screen goes black and then the Apple logo pops right back on.

    Before you do anything else, try charging via a wall outlet for a while, since its off. Then try turning it back on.
    When you put the device into recovery mode it allows you to restore the device when no other options work. You do risk losing everything currently strored on the ipad itself. Hopefully you've performed regular backups either via itunes, icloud or both. Evern if you have synced content to either of those, you may not lose everything. All previous purchases have been saved in the itunes and app stores, so you can dowload them again.
    while the ipad is off, press and hold the home button and plug the usb cord into the ipad. You should see a message pop up on the itunes window on your compoter screen that state it has discoverd an ipad in recovery mode.
    You should now be able to restore

  • I have itunes version 8.2 and would like to avoid downloading a newer version. The iTunes Store will not leave the page for iTunes 10. How do I fix this?

    The iTunes store will not leave the page for downloading iTunes 10. I just deleted iTunes 10 because of errors to purposely go back to version 8.2. Now I would like to keep 8.2 and not upgrade. How do I get this page to go away, or just keep 8.2? I would like to only have a version before 9.0. Please help!

    The iTunes store will not leave the page for downloading iTunes 10. I just deleted iTunes 10 because of errors to purposely go back to version 8.2. Now I would like to keep 8.2 and not upgrade. How do I get this page to go away, or just keep 8.2? I would like to only have a version before 9.0. Please help!

  • My ipod touch 4th generation will not leave the apple logo sign

    my ipod touch 4th generation will not leave the apple logo sign what do i do to turn it on and work ? please help

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • New Zen Micro will NOT connect!

    Hello all,
    I just bought a Creative Zen Micro player. I installed the software, charged the battery to full and guess what.....the Creative software does not recognize my player as being connected. And yes, I've checked device manager to see if it appears. It does, with the correct name and everything. So what is the problem? I've read other messages on this forum about this problem but it usually seems to be a problem after installing a new version of firmware. But this hasn't been done in my case because I haven't been able to get the stupid thing connected in the first place.
    I'm confused as to what to do next. I've tried resetting it by removing the battery and then holding the power button but this hasn't worked either. I first was using a usb hub to connect but after reading that you should avoid this, I tried plugging directly into a usb port on my machine. That also didn't make a difference. I've unistalled the player from the device manager about 5 times and reinstalled it. I've tried reinstalling the creative software/drivers about 5 times and no resolution. I've followed instructions from the Creative website step by step as the proper way to install the software but nothing works. I'm extremely disappointed to bring home a product that does not work out of the box. Oh, and yes I have Windows XP Pro so the OS isn't the issue here. I guess I will just return this useless product unless someone else has another idea that I could try. I'm really at my wits end.
    Thanks for listening to this short novel,
    Drawn-a-Blank

    The software that will not recognize the player is the Zen Media Explorer and Media Source. I'm not sure what firmware I have and I can't check since I'm not at home. But, I can't install new firmware even if I wanted too since it won't connect. However, I have downloaded the lastest drivers but I don't think I've installed the lasted version of Zen Media Explorer, so I guess that is one other option.
    Message Edited by drawn-a-blank on 07-23-2005 09:30 PM

  • My iPhone 4 will not leave the apple logo page?

    I updated my iPhone and it began installing and downloading the new update then all of a sudden it turned black, I thought it was part of the proccess so I just ignored it and then it flashed to the apple logo page, i waited a little and then it turned black again, then back to the apple logo. It keeps repeating this. I tried to plug it into the computer and nothing happened, I would push the home and lock button but my lock button is stuck. Please help!! I need this to work. I thought about letting it die, but god knows how long that would take. PLEASE HELP

    Hey laysams64,
    I would follow these troubleshooting steps:
    If a single application is not responding or stops responding when it opens, you can force it to close.
    If the device is unresponsive or if certain controls aren't working as expected, restart your device.
    If the device remains unresponsive or does not turn on (or power on), reset your device.
    If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
    If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
    Let charge for at least twenty minutes, then see if it starts normally.
    If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
    If the screen displays a red battery icon, continue charging the device until the battery is fully charged.
    If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
    Connect the device to your computer and open iTunes.
    If the device appears in iTunes, select and click Restore on the Summary pane. Learn more aboutrestoring iOS software.
    If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
    If the above steps do not resolve the issue, contact Apple.
    from: iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Welcome to Apple Support Communities!
    All the best,
    Delgadoh

  • The ringer symbol will not leave the screen ?

    Hello, I'm having trouble getting rid of the ringer symbol that is sitting in the middle of the screen. I'm also having problems with the volume not being able to turn down.  I think this is all related.  Any ideas?

    Could be a hardware problem and would need checking out, however it could also be a software problem in that it could be an app that's causing the problem that uses the ringer volume, such as Pandora, so first backup your iPad in iTunes then delete apps particularly that uses the volume control on your iPsd and see if the ringer symbol disappears for good then reinstall any apps that you deleted.

  • Safari Widget will not leave the screen

    I have been using several widgets that I created with Safari 3. Everything was going fine until today. One of my widget appears on my screen at all time. My other widgets works perfectly but this one always stays on the screen even if I pushed the F12 key and that all my other ones have disapeared.
    Any idea how to fix this? I though of just deleting the widget and recreate it after from the web page in Safari but I don't know where the widgets created with Safari 3 are stored. Please help! I have this big square on my screen ad I can't give rid of it.

    Could be a hardware problem and would need checking out, however it could also be a software problem in that it could be an app that's causing the problem that uses the ringer volume, such as Pandora, so first backup your iPad in iTunes then delete apps particularly that uses the volume control on your iPsd and see if the ringer symbol disappears for good then reinstall any apps that you deleted.

  • G4 will not boot past start up screen

    My G4 froze (while in Explorer, again). Ran Apple Disk Utility - which failed (1 volume - HD - needs repair). Then ran Disk Warrior to rebuild and optimize the HD - all the reports were ok, lots repaired, etc. Check with Apple Disk Utility again - disk verifies as ok, no problem - BUT - the same problem persists - the machine will not pass the start-up screen (Starting Mac OS X). I am running 10.4.11
    Does anyone have any suggestions on what to do next? Or, am I stuck doing a fire wire target disk mode to peel off any essential data followed by a system reinstall. For what it is worth this happens too much with this beast - I`ve had two HDs, replaced the RAM etc.
    Anybody have a clue?
    Message was edited by: Evan Lloyd

    An update - after running the Apple hardware test (disk) it seems as though there is a memory problem detected at startup. This would be in the installed 168 pin DIMM (not the more easily accessible upgrade slot. As memory can cause a variety of problems I will proceed to replace this and see if this fixes the problem. This is not the first time I have had memory problems - although it was previoulsy the SO-DIMM 144 pin card.

  • Zen Micro is not starting-up correc

    My Zen Micro is having problems while starting up. When you first turn the player on, it goes to a Creative screen. Then it displays Zen Micro. Usually, after this screen, it will go to the main menu. But mine stays at the Zen Micro screen. I'm not able to turn it off either; I have to take the battery out. It is not recognizing the USB cable either. Can anyone please help me?
    Thanks.

    Put your zen near your ear, and listen if you hear some ticking inside,
    i had the same problem and heard some ticking inside,
    This means that your harddri've has crashed
    but i was lucky and had guarantee
    But i hope you hear a thing.
    Greetz YcKe

  • Hi, I have a new cell phone, I wanted to give my iphone to my father, instead of deleting the content on the iphone I have deleted the entire iphone. It starts up no more. iTunes will not recognize the iphone. How do I get my old data back onto the phone?

    Hi, I have a new cell phone, I wanted to give my iphone to my father, instead of deleting the content on the iphone I have deleted the entire iphone. It starts up no more. iTunes will not recognize the iphone. How do I get my old data back onto the phone?

    Place the device in DFU mode (google it) and restore as new.

  • I am using an epson projector to present images downloaded to a thumb drive. I renames the images on export to "untitled 101, 102 etc. The projector will not recognize the sequence. It wants 001, 002etc. If I try to start 001 lightroom changes it to 1, 2

    I am using an epson projector to present images downloaded to a thumb drive. I rename the images on export to "untitled 101, 102 etc. The projector will not recognize the sequence. It wants 001, 002etc. If I try to start 001 lightroom changes it to 1, 2  ... 10,11 etc. How can I export and rename starting with 001?

    The projector may actually be processing a 3 digit number in numerical sequence.  Have you tried your export/collection in order  sequence starting with 101?  Assuming you have fewer than 899 images you should be OK. (I had to fiddle with export sequence for a display frame which used the file date and time for sequence!)

  • After downloading photoshop elements 12, the system started the install and asked again for the serial.  install process will NOT accept the serial #

    I purchased a software license for photoshop elements 12.  I started the process to download the software and provided the serial number on the download card.  Since the serial number provided was correct, the download started and completed.  Once installed the system started to install the software.  Again I had to supply the serial number.  This time the system will NOT accept the serial number.  I entered it again.  Not accepted.  I tried it again, this time with dashes.  Again the serial number is not accepted.  What do I do?

    Is there any message provided when serial number is not accepted?  If so, what does it say?

  • HT201272 Faulty download for a purchased film. How do I start the download again? The Apple Store thinks I have purchased the film and will not let me start the download again. Help!

    Film download was faulty but Apple Sypre will not let me start th download again. What do I do? I don't want to buy it again!

    Hello Zoocan,
    The best thing you can do is contact Apple Support, they will be able to help you. You can tell them you have receipts of your purchases.
    Apple Support (United States): 1-800-275-2273
    Cedric

Maybe you are looking for

  • Ical Help needed- can not delete a four year ical event

    I accidentally sent an ical event that lasts for four years and now I he cant delete it and it is taking up more and more memory on his phone as it is repeating infinitly every day?? Have tried restore but it still syncs with icloud. is there an easy

  • When creating new table in sqllite db via Flex it become encoded as "utf-16le"

    Hi Guys I have some annoying problem with my AIR application The application is communicating with a local DB (sqllite). as part of initial installation I'm checking if the db exist. in case not then: I create one (file) create the relevent tables in

  • BDS in BW

    Hello, Can someone provide me with information about BDS in BW? And is it possible to merge the documents into one document? Are there some customizing actions necessary? What is the purpose of the button 'Administration'? Regards, Jos van der Sterre

  • CIN condition type

    using condition based excise determination. for configuring for CESS and HIGHER CESS. Tax on Goods Movements - India - Basic Settings - Determination of Excise Duty - Condition-Based Excise Determination - Classify Condition Types i have tagged the 2

  • IMac wakes on its own after putting it to sleep

    Just got my iMac back from the shop with a new hard drive put in. After setting it up, it seems to wake from sleep on its own after a few minutes. Only change since before sending it in to be fixed (when i had no issues with sleep) is that I now have