N 95 KEYPAD NOT FUNCTIONAL

I am facing a peculiar problem as none of my keypad buttons including call answer/reject, d pad, menu and short buttons are responding. I've tried hard rsetting couple of times but to no avail. However I am able to answer incoming calls by sliding the device.

It has suffered a hardware failure. Take it to a nokia care point for repair.
Care points/service centres and repair info:
UK • Europe • Asia-Pacific • USA •
Canada • Middle East and Africa
Elsewhere: Click here, select your country, go to the support section, then select repair.

Similar Messages

  • Keypad not functional, have tried everything.

    Hi, I have recently come into a serious problem with my Verizon BlackBerry Curve 8300, and a lot of people seem to share this problem:  The keypad is not working at all.  I can scroll the trackball across the different menu items, but I can't press the trackball, nor any of the buttons on the keypad- even the red and green call buttons.
    It all started a few days ago when my Curve was working normally.  It had worked fine early that morning, and then I had proceeded to keep it in my pocket during the later morning hours, just as I did every day before that.  However, when I took it out to check my messages, I encountered the issue described above.  This has actually happened to me before on some occasions, but those were few and far between.  A simple battery pull would usually solve the problem.
    As the day went on, though, I did numerous battery pulls and the keys still would not work, no matter what I did.  I researched this problem and found that it could be a sign of wetness.  But I was certain that my Curve has never gotten wet, and I was able to prove this by checking the moisture stickers on the battery and the device.  Both did not indicate that the device had gotten wet- the battery sticker was still white with a red strip, and the device sticker was still a white square.  Even so, I still tried all of the solutions given on the other forums, including putting the phone in the oven, freezer, and in dry rice.  None of those worked, so it's clear that this is not an issue of wetness.
    I then moved on to the more daring solution of physically taking apart the phone and cleaning the keys with isopropyl alcohol.  I made sure the cleaning was absolutely thorough; I cleaned the keyboard membrane, the trackball and its membrane, the keys themselves, the silver front plate, and even the protective case that housed the phone.  There was no corrosion, but there were tons of dust, dirt, and lint covering all these parts, so I figured that that MUST be the problem.  I put my phone back together and turned it on, though, and the keypad STILL would not respond.
    The final thing that I did was back up the phone, reinstall the OS (version 4.5), and reboot the entire phone.  That didn't work either, so it couldn't be a software issue.
    Later in the day, though, I did one last battery pull just because, and then I started randomly mashing the keyboard.  Lo and behold, the phone WORKED.  I was so dumbfounded that this is what caused it to work again; I couldn't believe it, and thought it was too good to be true.  Turns out, it was.
    For most of the day, the phone worked fine, but one of two things would happen:
    1. The keyboard would lock up completely like before while doing simple tasks, and I would mash the keyboard until it would work again.
    2. The phone would freeze completely and I would have to do another battery pull.
    #2 recently happened again a few hours ago, but this time on the battery pull, the keyboard would not function again, even after mashing it numerous times.  So now, I am literally back to square one and left with nothing to do.  I still have NO idea what is causing this problem or whether it is a software or hardware issue.  My phone had gone from working perfectly one day to being completely unusable the next.  Now it seems like it's doing whatever it can to make sure it doesn't work.
    By now, most people would probably say that the only solution would be to replace the phone.  However...I can't.  My phone never had a warranty to begin with, and I won't be able to get the phone replaced unless I pay a huge sum of money, as our local Verizon stores don't carry this model anymore.  I am most likely stuck with this phone until our 2-year contract expires in about 4 months.  Until then, I am in need of a way to salvage the phone and make it last those final 4 months.
    If you have ANY possible solutions to this doozy of a problem, it would be greatly appreciated.   I hope that RIM acknowledges the many people that have this kind of problem and fixes it soon, because a cell phone should NOT have these kinds of problems, especially in emergency situations when we need them most.

    I notice from your system specs that you're running a very old version of Flash. Could you try updating to the latest one which is 10.2.159.1 It also contains a patch to fix a recently discovered [http://www.h-online.com/security/news/item/Adobe-releases-security-update-for-Flash-Player-1228930.html Zero Day exploit]. You can get it from here: http://get.adobe.com/flashplayer/
    Have you experienced any unusual events watching Flash videos lately? It's possible that you may have been a victim of just such an attack. It might be worth doing a malware scan using this well-known scanner from http://www.malwarebytes.org/ The free version is more than adequate to eliminate any current threats.

  • Numerical keypad not functioning in Windows partition of Boot Camp

    Unlike other users, the new keyboard is working fine in Windows -- mostly. Any ideas on why the numerical keypad on the far right isn't working? Is there a "Num Lock" key that I need to press when on the Windows side? If so: where? Can't find it on the keyboard.
    Also: does anyone know if one of the software applications (Parallels or VM Wave Fusion 2) is able to mediate these hardware issues?

    FYI, and for a bigger list of the Windows - Mac keyboard mapping see:
    Boot Camp: Apple keyboard mapping in Windows XP and Vista
    which points to handy articles like:
    Boot Camp: Apple Pro external keyboard mapping in Windows
    Ivan

  • Another network issue... C4780 - The wireless radio is not functioning. Contact HP support.

    Hi,
    I've trawled the forum for an answer to this and searched Google until I'm ready to drop the printer from a height.
    A long time ago my printer "lost" its ability to carry out any functions wirelessly, which is a shame because it was the wireless capability that sold it to me, over similar models at the time.  I coped with it, doing things the old fashioned way, more because I wanted to avoid spending an entire day messing around with it ...until today!  Well, I've started so I'll finish (hopefully) as having wireless printing back would improve my workflow.
    The error I'm struggling with is this one, when I attempt to configure printer for wireless:
    The wireless radio is not functioning. Contact HP support.
    I know others have had this issue, as my forum searches show and that for some people a solution was to reset the printer by holding in certain numbers on the keypad.  However, that thread does not explain how to reset the printer if it has no keypad, i.e. mine, the C4780.
    Anyone know how to do this?  Better still, is there a fix out there for what seems to be a common and recurring issue for HP products right across the board?
    Thanks in advance!

    I just sent you a private message. If you are not sure how to check your forum messages, this post has instructions.
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • Error:  Media In Device Not Functional

    I keep getting the error message, but only occasionally, when I connect my iPod Classic to my car. I have a factory cable so that I can access the content through the navigation but several times/week the iPod stops (sometimes mid song) and tells me "Media In Device Not Functional". The dealer has done a couple of "patches" that they said would fix it but it hasn't. I'm beginning to think it's the iPod itself since we have an iPod dock for our home stereo and it too was have issues with the iPod. I'm thinking of doing a Restore.

    Relieved to hear I'm not the only one with this problem with the 80gb classic, I Opened mine on xmas day and it worked ok for a few days then I got the problem as described...
    the ipod played music and videos fine but windows wouldnt detect it so I couldn't sync it ... tried a factory reset (hold action and menu button for 10 seconds) this didn't make any difference, I then managed to get it into diagnostic mode by doing a factory reset, then holding the action button and the left arrow before the apple logo disappears ... after going through all the keypad diagnostics which passed windows again recognised the device, I then opened Itunes which recognised that the ipod had a serious error and offered to restore it back to its factory settings, which I did, I then also updated it to the latest software
    again it worked fine for a few days and then I got the same error in windows xp again ... thinking the drivers might be corrupt on my PC I tried it on a different PC but with no luck, again got the same error
    My Ipod is now back at Comet ... but because of their stupid policy I cannot get a replacement as it was bought more than 14 days before I took it back, even though it wasn't unboxed till christmas day!! so it looks like I'll be without it for a while,
    I will keep posted on the outcome but any other feedback would be appreciated from anyone who has had the same problem

  • E71 , KEYS NOT FUNCTIONING PROPERLY.

    FROM LAST SEVERAL DAYS MY DEVICE KEYPAD NOT PROPERLY FUNCTIONING, IF I PRESS A IT TYPR AS "AF" , IF I PRESS Q IT TYPE AS "QR" ALSO WHEN I PRESS RIGHT OR UPPER NAVIGATION KEY IT JUMP UP AND SELECT NEXT ICON, THESE TYPE OF PROBLEM IS WITH OTHER KEY ALSO.. SIR PLEASE HELP . THANKS

    how did you update the software?
    try using the NSU to reinstall it.
    www.nokia.com/nsu
    edit:  scratch that....that link no longer works.
    try reinstalling the software through ovi suite....and if you still have pc suite, then you may already have nsu on your pc

  • Keypad not working properly win 10

    Hi there, I have an Aspier 5332 OS windows 10 pro, the keypad is not functioning correctly. Scroll dosen't work, the mouse pad moves the cursor but tapping to select something brings the context menu up. It just doesnt feel right. Selecting stuff, it feels like your having to click the button twice. Before OS update the mouse was using alps touchpad. The device manager says its now ps/2 compatible mouse  Device manager says it has the latest drivers installed. Very annoying. After searching the web this seems to be a big problem. Any solutions to this ? Thanks

    Robtb,
    You can attempt to download, remove what drivers are installed, and install the drivers from our support site to see if they resolve your issue.

  • Photosmart c309a- 'The wireless radio is not functioning, contact HP support'

    My Photosmart c309a wont connect wirelessly. Upon running the wireless network test, the report states, and I quote "The wireless radio is not functioning. Contact HP support". The report then states the following:
    Wireless on                    PASS
    Wireless working         FAIL
    and everything following that stated as 'not run'.
    Ive searched for other threads on the subject, and the only sloutions I can find are unplug the printer and plug it back in to reset it (made no difference), and try the HP print and san doctor (link was dead, found it manually and didnt work as it cant connect to or even see the printer on the network).
    So the question is, is this a hardware fault, and if so what can be done about it?

    Hello,
    Yes, it is an hardware issue and indicates that the Wireless card is not functional.
    Please call HP Tech Support for further assistance.
    If you are in US , the toll free # is 1-800-474-6836 .
    If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.
    Regards,
    Jabzi
    Give Kudos to say "thanks" by clicking on the white star under my name.
    Click "Accept as Solution" if it solved your problem, so others can find it.
    I work for HP
    Regards,
    Jabzi
    Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
    Click "Accept as Solution" if it solved your problem, so others can find it.
    Although I am an HP employee, I am speaking for myself and not for HP.

  • Error message saying a device attached to the system is not functioning

    i m getting an error message saying a device attached to the system is not functioning whenever i m trying to connect my pc to my smartphone. i tried all your options like uninstalling failed updates from my update history, checking if their is any flag
    in device manager option but nothing helped me.. plz solve my problem..

    Hi,
    Could you please have a share with your phone's information?
    Based on what I know, different phones may have different softwares developed by the manufacturer to make the connection through Windows operating system, we may check with the phone's manufacturer side and see if there could be some helpful information
    offered.
    Besides, please take a check with
    Event Viewer and see if any special errors logged there.
    Best regards
    Michael Shao
    TechNet Community Support

  • Bridge not functioning in PhotoShop CS3 Extended

    I deactivated Photoshop CS3 on a computer I was no longer using and installed it (CS3) another computer.  I activiated CS3 on the new computer.  However, when trying to use Bridge, I get a message that says that Adobe no longer supports Bridge Home and Bridge does not function on the new computer. Is there anything I can do to get Bridge to function as part of CS3 Extended?

    Thanks, that worked. 
    In a message dated 12/28/2011 10:13:56 P.M. Eastern Standard Time, 
    [email protected] writes:
    Re:  Bridge not functioning in PhotoShop CS3 Extended
    created by Curt Y (http://forums.adobe.com/people/Curt+Y)  in Bridge 
    Windows - View the full  discussion
    (http://forums.adobe.com/message/4107610#4107610)

  • Satellite P300D-110 integrated webcam is not functioning properly.

    Hello everyone,
    as the title says, the integrated webcam of my Toshiba Satellite P300D-110 is not functioning properly. Allow me to explain. Using the Camera Assistance Software I can take photo's and record music. If I try to record a video the preview screen turns up black and the end result tuns out black aswell, completely black.
    Whenever I try to use my camera with applications such as MSN Live Messenger, Skype or at community websites using Firefox, Internet Explorer or Safari the application in question crashes.
    *How did this happen?*
    You tell me. This is how it went;
    * Day 1: I've started up my laptop and looked at my fresh and clean install of windows vista home premium. I tried out my webcam using the webcam assistance software and it worked like a charm.
    * Day 2: Once again I boot up my laptop and try to start my webcam only to find out that it no longer functions.
    To give a quick summary of the thread;
    * Using Camera Assistance Software provided by Toshiba I can take pictures.
    * Using Camera Assistance Software provided by Toshiba I can record sound.
    * Using Camera Assistance Software provided by Toshiba I can _*NOT*_ record or preview a video.
    * I can not start my camera using any other application such as but not limited to; MSN Live Messenger, Skype, Mozilla Firefox, Internet Explorer and Safar.
    * I have downloaded and isntalled the latest drivers from the Toshiba website.
    * My laptop is about a week old.
    I'm not sure what more I can do, all I want is for the webcam to work, if anyone can help me out please do so.
    And if possible WITHOUT having to reinstall Windows Vista Home Premium.
    I haven't even used it and wouldn't want to make that a solution for all the problems that might occur in the future.
    Sincerely,
    a sad customer.

    Using Camera Assistance Software provided by Toshiba I can NOT record or preview a video.
    Can you please describe the steps how you try to do this? I must ask you this because it runs well on my notebook. When the recording is finished player opens and you can see recorded movie. It is avi format and at the top of this player you can see the path where the movie is saved.
    Most strange thing for me is that you cannot use it with Skype. Ok for MSN is not the perfect but there is absolutely no problem with Skype. Check the settings and it must work somehow.

  • My audio and cam is not functioning anymore.my laptop model is Satellite A200-130.what shall i do?

    im having a problem with my laptop.the audio and cam is not functioning.i dont know why/
    please help me what to do.do you think program files about these were deleted?

    Probably best to post in the Toshiba Support Forums Europe.
    -Jerry

  • Keyboard+trackpad not functioning at all on HP 2000 Notebook PC! please help!

    Tonight I turned on my laptop (HP 2000 Notebook PC) to find that the Keyboard and track pad was not responding, the only thing that worked was the wireless mouse.
    I can not find the product number but the name is HP 2000 Notebook PC, the operating system is Windows 8, I can't login to see if there are any error messages, the last thing I remember doing was trying to apply a new cursor image and it told me to restart and when I did I couldnt log back in or type anything at all, I could only use the mouse.
    Also the things I have tried to do are: Restart Computer, Take out batter and restart. (I cant do much because I can't type in password)
    All help will be greatly appreciated!
    UPDATE: I logged in using the On-Screen Keyboard, it seems like a hardware malfunction and not a virus because i cant find anything in my downloaded stuff that wasnt there before. So it is just a hardware malfunction.
    UPDATE #2: it says that the driver (for keyboard and touchpad) may be corrupt or missing and it says Code 39 in parenthesis.

    Hello Oceanlife,
    You state that the keyboard and touchpad are not functioning, that is correct? I will try to assist you with this issue.
    As of today are you still having this problem?
    If you have, any more questions do not hesitate to ask. .
    Thanks
    Clicking the White Kudos star on the left is a way to say Thanks!
    Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

  • Fairly certain that FileStream.writeObject() and FileStream.readObject() do not function - at all -.

    I've struggled with this since Jan 9th, 2013 (if not longer) and the only conclusion I can come to is that this simply does not function.  No matter what I try and no matter what resource (and I'm finding precious few) I follow to try to implement this within Flash Builder 4.7, Flex SDK 4.6.0 (Build 23201), AIR SDK 3.5, I only succeed in creating a file (with the correct name) that is 123 bytes in size that reads back in as NULL;
    I've tried using ByteArray.writeObject()/readObject() as an intermediary with FileStream.writeBytes()/readBytes(), with no luck.
    I've tried instantiating an object, setting properties and then using that.  I've tried instantiating my correctly formed ValueObject (including the remoteClass alias metadata tag).
    I've tried using -verbatim- the example provided in the top most suggested 'Community Help' resource http://www.switchonthecode.com/tutorials/adobe-air-and-flex-saving-serialized-objects-to-f ile It is worth noting that this solitary example of the procedure/SDK-usage is dated to Flex SDK 3.0 and at least 04/04/2009 (first comment on the article).
    My frustrating hell (one version of many methods attempted) is detailed on StackOverflow (including -all- mxml, as, and trace output), but so far, no assistance has been forthcoming, alas.  This is a severely stripped down and simplified version of what had been a far more complex attempt:
    http://stackoverflow.com/questions/14366911/flex-air-actionscript-mobile-file-writeobject- readobject-always-generates-null-w
    An earlier post* detailing a far more complex attempt interation, with, alas, just as little help (guess this isn't a hot button topic) forthcoming:
    http://stackoverflow.com/questions/14259393/flex-actionscript3-filestream-writeobject-fail s-silently-in-ios-what-am-i-doin
    * I previously suspected that it was only failing from within iOS on an iPad, but the first example (the stripped down version) made it evident that it didn't work in the AIR mobile device simulator (iPad) in the Windows environment, and indeed, didn't work in a non-mobile project in the windows environment AIR launcher.
    I'm at a loss, upset, frustrated, in major trouble with my supervisor/deadlines, etc.
    I would very much appreciate any suggestions/help/confirmation/etc.
    Just to move ahead with development I've opted for a far less preferable solution of writing out both an XML file and a JPG file.  I very much do not like this and very much want to store encapsulated serialized objects locally in the same way I assume will work for storing remotely with AMFPHP (if the project ever gets to that point *sigh*).
    Again.  Would be so grateful for any help.

    I want to add to this post as I marked it as "The Answer" though it does not indeed contain the answer directly, for those who come looking for simliar solutions.
    harUI prompted me to realize that my metadata term needed to be capitalized (RemoteClass instead of remoteClass).  As the metadata tags may be user defined, the compiler throws no errors (or warnings *grumble*)
    package vo
        import flash.display.BitmapData;
       // [remoteClass(alias="PTotmImageVO")] incorrect
       [RemoteClass(alias="PTotmImageVO")]
        public class PTotmImageVO

  • Multi-touch display is not functioning as normal

    multi-touch display is not functioning as normal on the right half of the screen....

    Hi James,
    Thx for the quick reply...
    I have already tried most of these troubleshooting steps but no go....
    Also, when you tap or use only the right half of the screen, the touch display is inconsistent and makes a wierd sound [ like a hollow tub or something ] and it's not a cosmetic issue...
    ----Apple store / Authorized Service Center is still working on this ongoing issue with no results and still not confirming for the iphone replacement...Thnx..

Maybe you are looking for