N Ultra Range Pluse WRT160n help

I just bought this router and have it set up.  My desktop has no problems with the internet, but when I use my Laptop or Xbox 360 wirelessly I loose internet connection in the middle of using it.   It will connect for a few minutes and then just disconnect.  Any ideas of how to get this problem worked out? 

Well you need to make some changes on your Router, So your Laptop and your XBOX can go online at a same time.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
-Here select manual configuration...Wireless Network mode should be mixed...
-Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...
For your XBOX Here are some settings which you can set on your Router as well as on your XBOX. 
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
4) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
5) Click on set-up and change the MTU Size to 1452 and click Save Settings...
6) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
7) Also assign the DNS Addresses on the Xbox Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
8) Turn off your modem, router, and Xbox...Wait for a minute...
9) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Similar Messages

  • N Ultra Range Pluse WRT160n router

    I can't connect my N Ultra Range Pluse WRT160n router wirelessly to my laptop.It showing undefined network only & it IP address taking is starting with 169 and it is not asking the network share key also . But I can connect to another laptop & my laptop can connect another wireless connection .kindly reply me what is the problem?
    one more problem i have when i  try to connect wirelessly to another laptop it is asking pin only not asking the key
    kindly reply me
    Solved!
    Go to Solution.

    I think you need to make some wireless changes on your Router. I think this will solve the problem.
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    -Here select manual configuration...Wireless Network mode should be mixed...
    -Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.
    NOTE : Passphrase should be more that 8 characters...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...
    OR.
    While connecting to your Wireless Network, If it ask you for the Pin number, Flip your Router upside down, and you will find the 8 digit Pin number, note down the pin number and when prompted type and Pin number and click on Connect and you should be able to go online wirelessly from your Computer. 

  • WRT160N v3 Ultra Range - range not very far

    Lighting burnt out my wireless-G router so tech support recommended I upgrade from Wireless G to wrt160 for better performance. However, with this one I don't have near the range the wireless G had. The wireless G had a range over 200ft with no problem but the wrt160N Ultra Range won't reach 150ft. Do I need to make a change in the settings for it to reach further?

    Re-adjust the wireless settings of your Router...
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    - Here select manual configuration...Wireless Network mode should be mixed...
    - Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...

  • SQL*PLUS 에서 ONLINE HELP 기능

    제품 : SQL*PLUS
    작성날짜 : 1999-10-08
    SQL*PLUS Help
    =============
    SQL*PLUS 에서 Online Help 기능을 제공하여 굳이 SQL Reference 를 참조하지
    않아도 Online 상에서 확인이 가능하다.
    그런데 간혹 help 에 문제가 생기는 경우 다음과 같이 새로 생성하면 된다.
    1. help 디렉토리로 이동한다.
    % cd $ORACLE_HOME/sqlplus/admin/help
    2. SYSTEM user 로 SQL*Plus 에 Login 한다.
    % sqlplus system/<password>
    3. 해당 디렉토리의 "helptbl.sql" script 를 수행한다.
    SQL> @helptbl
    해당 스크립트는 Help 라는 테이블을 생성하고 Public 으로 지정한다.
    4. SQL*Loader 로 필요한 Record 를 Help 테이블에 로딩한다..
    % sqlldr system/manager control=plushelp.ctl
    % sqlldr system/manager control=sqlhelp.ctl
    % sqlldr system/manager control=plshelp.ctl
    5. SYSTEM user 로 SQL*Plus 에 Login 한다.
    "helpindx.sql" script 를 수행한다.
    SQL> @helpindx
    해당 스크립트는 필요한 각종 view 와 index 를 생성한다.
    // 위의 사항은 Unix 계열의 SQL*PLUS 에서 적용이 되는 내용이다
    Windows 95/98/NT 에서는 현재 On-line Help 가 지원되지 않는다.
    다만 Oracle install CD 에서 Oracle Online Documentation 을 인스톨 한
    후 Adobe Acrobat runtime 으로 보아야 한다.
    DB SERVER 8.1.6 이상에서는
    SQLPLUS에서 사용되는 help 기능만 제공됩니다.
    8.1.6 이상에서 help를 생성하기 위해서는
    % cd $ORACLE_HOME/sqlplus/admin/help
    % sqlplus system/<password>
    SQLPLUS>helpbld.sql
    SQLPLUS>helpus.sql

    I personally don't like SQL Developer or TOAD, though perhaps I'm in a minority. I agree completely. Toad does a lot of things but many of are ill thought out, the most obvious is the default feature of displaying a result time after fetching the first screen of rows. This alone has led to hundreds of posting along the lines of, I have this query that returns 12 billion rows. In a stored procedure it takes days, but it completes in 12 milliseconds in TOAD?
    The last I looked SQL Developer had that typical Java sluggishness on a Windows box, and I am still not interested in whether that is a Windows or Java problem. I just know that if I have to use Windows I tend to choose applications that are not written in Java if possible.
    It also was unable to connect using OS authenticated accounts which effectively ruled it out as anything other than a toy as our development environment mandates it. I believe there may be a workaround, but there are always hints of waving a rubber chicken at it and frankly why bother at this stage.
    PL/SQL Developer is by far the best.

  • Dynamic range: NEED SOME HELP (any help i can g

    here's the reason i am here:so lately i've decided to dump the idea of playing movies on my xbox360 and started using my hometheater PC to play it. since it has a X-fi extreme Music on it. and i do like it better because the xbox360's decoder down samples everything to 640kb Dolby Digital 5.. i want to experience the full quality (if not as high as i can get) of Dolby Digital Plus, and DOlby True HD (both lossless soundstream), and the only way to do that these days are through HDMI or analogue output, since SPDIF nor Optical toslink can provide enough bandwidth required by both DD+ and TrueHD soundstream. so now you know the reason i am here. i do understand Xfi currently does not offically support DD+ nor TrueHD, but at least through the analogue output i believe i can get a better fidelity than my 360. here's my problem:like i said, the sound quality is MUCH better through the Xfi than the Xbox360's internal decoder. but i do havve one problem. because the dynamic range is so high, i find myself regulary adjusting the volume several times through the whole movie. so i started playing with the "Smart Volume" setting, since it alters the dynamic range by compressing it. the result is a HEAVILY compressed dynamic range which is not very ideal. because i can hear the level shifts when there's a high volume element followed by a low bolume element, i can hear a very unatural alteration. is there anyway to adjust the level of the dynamic range? because smart Volume only allows for "on" or "off", i wish there's a level slider. another side problem i just found out with my card is that, apparently, my card is a Dell's Xfi Extrmem Music card, that means i am missing the DOlby Digital EX audio console control, and the DTS ES audio console control panel. i understand that both supposely would allow me to adjust the dynamic range levels. i only found this out when i tried to look up the dynamic range option in Xfi on google and there're?A LOT of angry people who are missing those two features in their Extreme Music card. apparently it has to do with Dell's cost cutting strategy in which all their Xfi cards audio decoder are license from Sonic instead of creative, so hardware wise, there's no differnce. but at a software decoding level, there're som features missing. and the people who bought these cards from Dell are real pissed off because they speficied on their page that's it's an Xfi Extreme Music card just like the retail, what they shoud've done is putting the "Dell's" logo next to it stating it's a Dell's Xfi Extreme Music card, meaning some features might not be the same. anywho, i realize it's a lot to read, but i searched the forum and googled the net, can't find any solution. would it be possible for the next driver update to include a slider option for adjusting different levels of Smart Volume?thank you.Message Edited by howzz854 on 04-08-200704:50 AM

    and i forgot to list my hardware specs:?Athlon64 3200+ @2.6ghzGskill PC4000 2XGB ramGeforce7800GTXFI Extreme Music (Dell's crap_ missing some features that's suppose to be there in the retail versions)DFI NF4 Ultra-D moboDual 0,000 RPM (2 X 74GB)?WD raptors, 0 array, + 2 Maxtor 200GB (for storage)Enermax 600watt PSUNEC 6X DVD romToshiba external HD-DVD dri've?WinXP SP2?Message Edited by howzz854 on 04-08-200704:28 AM

  • Win XP will not install on K9N4 Ultra based system, please help!

    Hello, i was hoping some1 could help me with a problem ive been trying to sort out for the past week or so.  After buying and building a new system i havent been able to get Windows XP to install, the setup formats and copies the initial files correctly then restarts the computer for the first time, the Windows logo then displays on the screen but after that the screen goes blank and nothing happens, the HD led flashes regularly but nothing else happens.  Ive tried installing with both XP home and pro, neither worked, installing Vista works without any problems. I have tried using the Sata drivers from the motherboard CD and from MSI website but that doesnt make any difference, ive also checked the CPU temp which at idle is 25C.  Ive tried pretty much everything i can think of without buying extra components to try which i am reluctant to do. On one occasion XP did install but at the time i was trying to install to the second hard drive with a failed install still on the first hard drive, thinking that whatever was causing the problem had been solved i then formatted both drives to do reinstall so that i wouldnt have to screw around with the boot record manually, ive since tried recreating this situation but it hasnt worked when i tried it a second time.  Ive tried installing with only one hard drive installed with a freshly made partition and full format and it still did not work.
    My specs are:
    MSI K9N4 Ultra-F
    AMD AM2 X2 3800+
    Corsair DDR2 667Mhz 2 DIMMS 1Gb each
    MSI Geforce 7300GT 256Mb
    Seagate Barracude 7200.9 Sata2 hard disks (2) 250Gb each
    450W Win Power PSU
    There is also a Creative Sound blaster audigy sound card and a samsung DVD RW, nothing else is connected.
    The only thing that i could think might be a problem is the PSU which is a pretty cheap one, also only has 20 pin and 4 pin connecters (both are connected) but i was under the impression that this would be ok.
    If anyone has any ideas or knows something i dont about why this isnt working with XP please let me know.
    Thanks

    Have you checked the memory timings in BIOS Setup?  At one time MSI used to just get them wrong and I recall having to set DDR CL to 3 (correct for the DIMMs I had), instead of the 2.5 it chose - no idea on DDR2 though but check that your Corsair specs cross-check with what's used.  Is the Sound Blaster Audigy installed?  If so try taking it out and go into BIOS Setup and Load Optimized Defaults, then disable all the "fluff" which is not absolutely necessary for a basic install, like on-board audio, ethernet, unused IDE/SATA channels, FireWire(?) etc.  You want to get down to a minimum required Windows driver set and if that helps, start adding things back one by one.  Also check your mbrd seating for shorts and the CPU heatsink seating... does the CPU temp look right in BIOS Setup.

  • All months in date range plus running count

    Oracle 11g
    Hello all,
    Having trouble getting the following query to return proper results. Have a table with a MEMBERNO, BUSINESS_LINE, ELIGIBILITY_START_DATE, ELIGIBILITY_END_DATE.
    MEMBERNO is not unique
    BUSINESS_LINE is not either
    Start and end date are periods of time where: MEMBERNO&BUSINESS_LINE have changed
    I need to list the member number, business_line, and each month that falls within the date range beginning with eligibility_start_date & eligibility_end_date, as well as a running count of the total in that span.
    Eg.
    member, business_line, month, year, count
    1234, bus1, 01, 2001, 1
    1234, bus1, 02, 2001, 2
    1234, bus1, 03, 2001, 3
    Here is my SQL, it is not sequencing the months dates correctly and I can not figure out why. Any help is very appreciated:
    SELECT memberno,
    business_line,
    TO_CHAR (ADD_MONTHS (start_date, LEVEL - 1), 'MM') as MONTH,
    TO_CHAR (ADD_MONTHS (start_date, LEVEL - 1), 'YYYY') as YEAR,
    ROW_NUMBER () OVER (PARTITION BY key1 ORDER BY start_date ASC) as MEMBER_MONTH_COUNT
    FROM (SELECT memberno,
    business_line,
    eligibility_start_date as start_date,
    eligibility_end_date as end_date,
    member_nbr || business_line as key1
    FROM eligibility)
    CONNECT BY LEVEL <=
    MONTHS_BETWEEN (TRUNC (END_DATE, 'MM'),
    TRUNC (START_date, 'MM'))
    + 1;
    Edited by: 935047 on Jul 25, 2012 5:58 AM
    Edited by: 935047 on Jul 25, 2012 6:18 AM

    935047 wrote:
    I need to list the member number, business_line, and each month that falls within the date range beginning with eligibility_start_date & eligibility_end_date, as well as a running count of the total in that span.
    Eg.
    member, business_line, month, year, count
    1234, bus1, 01, 2001, 1
    1234, bus1, 02, 2001, 2
    1234, bus1, 03, 2001, 3I could not understand what the Running Count mean. Hence, I used Row_Number (Same as you did).
    Below query might match yours.
    with data (memb_no, bus_line, st_date, end_date) as
      select 1234, 'bus1', to_date('01-01-2001', 'MM-DD-YYYY'), to_date('06-30-2001', 'MM-DD-YYYY') from dual
      union all
      select 1234, 'bus1', to_date('07-01-2001', 'MM-DD-YYYY'), to_date('07-30-2002', 'MM-DD-YYYY') from dual
    min_max as
      select memb_no, bus_line, min(st_date) st_date, max(end_date) end_date
        from data
       group by memb_no, bus_line
    lvl as
      select level l
        from dual
      connect by level <= (select max(round(months_between(end_date, st_date))) from min_max)
    select memb_no,
           bus_line,
           to_char(add_months(st_date, l - 1), 'MM') months,
           to_char(add_months(st_date, l - 1), 'YYYY') Year,
           row_number() over (partition by memb_no, bus_line order by st_date) cnt
      from min_max cross join lvl
    order by year, months;
    ----OUTPUT------------------------
    MEMB_NO BUS_LINE MONTHS YEAR CNT
       1234 bus1     01     2001   1
       1234 bus1     02     2001  19
       1234 bus1     03     2001   3
       1234 bus1     04     2001   4
       1234 bus1     05     2001   5
       1234 bus1     06     2001   6
       1234 bus1     07     2001   7
       1234 bus1     08     2001   8
       1234 bus1     09     2001   9
       1234 bus1     10     2001  10
       1234 bus1     11     2001  11
       1234 bus1     12     2001  12
       1234 bus1     01     2002  13
       1234 bus1     02     2002  14
       1234 bus1     03     2002  15
       1234 bus1     04     2002  16
       1234 bus1     05     2002  17
       1234 bus1     06     2002  18
       1234 bus1     07     2002   2
    19 rows selected

  • How to include a date range in Search Help

    Hi All,
    I need to include a range for a date field in a Search help.
    That is I have to add From Field and To Field for the same field in the search help.
    Please advise.
    Regards.

    If you are going to add an entirely new field (not existing in the SAP standard search), try using EEWB and for the query on that field would be a modification to the Model access class.
    Regards,
    Shailaja

  • WRT160N Help !

    Hey forum, I have a couple of questions regarding how to secure my wireless connection from others around me.
    This  is what my network is looking like, but I think my wireless connection isn't correct with that image. I have my wireless router connected through my hardwired router. Is there a reason it isn't showing up at all on this image? I'm assuming the "Unknown" device is it since it is the only one unaccounted for:
    Next.
    I want to change my privacy settings on my wireless that no one else can access it, of course. When I go to Task/Tools then Change Wireless Security, it goes through the process of Retrieving Router Settings of Scanning The Network, but after that, I get this error message, I have no idea what this means or how to fix it so I can protect my network:
    Next.
    I have a laptop with a wireless connection. The wireless internet worked for maybe 10 minutes while I was typing this message out, but when I went to look at it, it had stopped working. I also have an Apple iTouch with wireless that is working without a problem. I figure I still have to add the laptop to the network. So I go through the steps in the EasyLink Advisor and when I try to add the laptop with the wireless connection, I don't have the ability to add one. This is what the screen is showing me:
    My cable modem is a SBV5120
    My hardwired router is a LinkSys BEFSR41 [Ver. 2]
    My wireless router is a LinkSys WRT160N [Ver. 2]
    I can gladly take more screenshots and post as much more info to help clarify my situation. Thanks!

    If your connection only lasts for a couple of minutes you should upgrade the firmware on the router...Download the Firmware here , Follow these steps to upgrade the firmware on the device: -
    Open an Internet Explorer browser page.In the address bar type - 192.168.1.1...Leave username blank & in password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Press and hold the reset button for 30 seconds...
    Then, unplug the power cable while holding down the reset button for another 30 Seconds...Plug the power cable back in, and keep holding down the reset button for another 30 Seconds...Release the reset button...Now re-configure your router...
    As your Internet Service Providor is Cable follow this
    For Wireless Settings, please do the following : -
    Click on the Wireless tab-
    -Here select manual configuratioon...Wireless Network mode should be mixed...
    -Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the standard channel to 11-2.462GHz...
    - And wireless SSID broadcast should be Enabled and then click on save settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bits.Leave the passphrase blank, don't type in anything...
    Under WEP Key 1 type in any 10 numbers please(numbers only and no letters) and click on save settings...
    Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network.Now try if you could see the Wireless Network Name/SSID and try to connect...
    Click on Advanced Wireless-
    settings>>Change the Beacon Interval to 75 >>Change the Fragmentation...
    Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...it shouldbe fine now...

  • Big problem with webcam vista plus need HELP !!

    Hello Everyone !
    I own Creative WebCam Vista Plus VF0090.
    My system is windows 7 64 bit and i cant install any driver for my cam to work.
    Please help... thanks.

    Hi Itay84,
    Sorry but I don't think there is driver for your webcam. Please refer to the driver availability chart for updates.

  • Range or Value Help in VC 7.2

    Hello Guys,
    I'm using VC 7.2 SPS 02, and also I am not able to use a range filter. In previous versions there was the option of Value Help. No more?
    If anyone can help, thank you!
    Thanks!
    Milton

    Hai,
    if your providing value help for particular field u have select key and value field . then only the data will pouplate in the value help.
    Regards ,
    Venkat

  • Iphone 6 plus preorder help!!

    I ordered my iPhone 6 plus 16 gb space grey at around 2:56 am est on the 12th and I am getting a 10/14 shipping date. And now it's saying no information is available on the shipping estimate. What's the deal?

    Verizon, I am having issues as well. I did not a provide an email address on my order so I didn't get a confirmation but I know my order is in process. I ordered it around 12:10pdt and it had a "deliver by date" of 9/19. I called to check my order status over phone and it said my order was "pending shipment". But when I called a rep, she said I had to sign a "terms and conditions" before my phone was shipped. She then told me my order was "still in process". When I asked her what that was, she was unable to help and redirected me to another person. Is there something I have to sign in that confirmation email? I had them change it to my real email and haven't received any news. I am assuming that the "pending shipment" status is the latest update they have.

  • OM Number Ranges Problems please help

    Hello Gurus!
    My client wants 2 things in OM:
    1) 9 Digit Org Unit Code
    2) Mixture of Alphabets and Numbers for Unit code.
    Can anyone suggest which one is possible and if both are possible?
    Thanks,
    Soniya

    Hi,
    I think this helpful to u.
    Personnel Management &#61664; Organizational Management &#61664; Basic Settings &#61664; Maintain Number Ranges &#61664; Maintain Number Ranges.
    You must assign a unique no. for every object, Eight digit numeric.
    for example
    ‘IN’ refers to internal assignment.
    ‘EX’ refers to External assignment.
    It is recommended to maintain Internal Assignment for all your objects such as C - Job,
    O - Org. Units and S – Positions.
    Subgroup     NR int. assgnmt     NR ext. assgnmt
    $$$$     IN                           EX
    01C     IN                           EX
    01D     IN                           EX
    01E     IN                            EX
    01O     IN                           EX
    01S     IN                            EX
    Regards,
    Revathi.

  • WRT160N HELP WITH NETWORK CONNECTION

    I have a WRT160N wireless router and i have it on windows 7, i have a network set up and when i go to try and connect, it shows up as a error and will not connect? I see my personal network but i just can connect? please help
    (Mod note: edited for guidelines compliance)

    When you are trying to connect to your wireless network are you getting any kind of error message?
    When you Hardwired your computer to the router are you able to go online?
    If you are able to go online from the Hardwired computer then you can login to the setup page of the Router, and click on the Wireless tab and below change the Wireless Channel to 1, and then click on the sub tab "Wireless MAC Filter" if you have enable the wireless mac filter disable it and then try to connect to your wireless network.

  • Youtube doesn't work on my iPhone 6 plus,any help ?

    youtube doesn't work on my I phone 6 plus ? any help ?

    Would you please provide a little bit more info about your issues with YouTube? What doesn't work? YouTube in Safari? YouTube in Chrome for iOS? The YouTube app? What happens when you enter youtube.com or open the app? ...

Maybe you are looking for