N5800 not maintaining connection with plantronics ...

it can be easily paired with headset. but every now and then it disconnect and connect with the headset. i have already consulted with plantronics and mentioned a power cycle to be done and remove current pairing and re-pairing it again. but the issue is still exists.
5800 current firmware version is v 30.0.0.11
any idea from nokia's end?
highly appreciatted a response.
thanks

i have the same problemo but i read that it can be rectified with broadcomm bluetoth stack.
Regards

Similar Messages

5800 does not maintain connection with Sony Ericss...

I recently upgraded from the N70 to the 5800. I was using a Sony Ericsson HBH-602 bluetooth headset with the N70, and it worked perfectly. Specifically, as long as bluetooth was enabled on the phone, all I had to do was turn on the headset and it would connect with the phone, and remain connected as long as both were powered on and in range.
With the 5800, the headset also connects to the phone when turned on, but the phone drops the connection a few seconds later. However, if I initiate the connection from the phone, it works as expected, and remains connected. This is usable, but it would be preferable if I could control the connection entirely from the headset, as described above.
Any suggestions would be greatly appreciated.
Thanks in advance.

I have the same problem but with Nokia BH-903.
It worked really fine with the N95, but with the 5800 it doesn't work so well. When i am in a call it always disconnect to the phone, or when i am listening to music it paused the music or it disconnect.

HT4528 I have an IPhone 5 and the bluetooth will not stay connected with my 2011 Chrysler 200. I was told by Chrysler service department that it is a problem with the IPhone 5. Is there an update or a fix so i can use the bluetooth in my vehicle?

I have an IPhone 5 and the bluetooth will not stay connected with my 2011 Chrysler 200. I was told by Chrysler service department that it is a problem with the IPhone 5. Is there an update or a fix so i can use the bluetooth in my vehicle?

Iran uses GSM, so the iPhone 5 will work. It is already unlocked. Just put local Iranian SIM in phone.

Iphone 5 wifi does not maintain connection or automatically connect

I phone 5 does not always maintain connection and does not automatically connect. I have selected the wifi system and entered password for such but each time I have to reenter password.

"Ask to join networks" is off. I also tried turning off the phone and restarting it. My wife's iPhone 5 is doing the same thing. Could it have something to do with my router?

Wireless does not hold connection with b43 driver!

Hi everybody!!
It's my first time here in the forum, so nice to meet you.
I have a laptop Acer Aspire 3050 and I recently formatted it to install the new Arch 2009.08.
It's pretty cool, but I can't make my wireless card (Broadcom BCM4318) work with b43 driver. It worked very well with Arch 2009.02, but now it's a pain!
It recognizes the driver, loads it and connect with no problems, but when I ping my desktop machine, it says that unfortunate message "Destination Host Unreachable"
It sometimes works when I do these commands about 5 or 10 times:
./connect
ping 192.168.0.1 >>> Destination Host Unreachable
ifconfig wlan0 down
rmmod b43
/etc/rc.d/network restart
modprobe b43
./connect
[... many more times]
but even when it does connect, it usually can't hold the connection for more than 15 or 20 minutes. And I have to do it all again.
Hear goes some info on configuration files so it may help you:
lspci -vk
08:04.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
Subsystem: AMBIT Microsystem Corp. TravelMate 2410
Flags: bus master, fast devsel, latency 64, IRQ 21
Memory at d0200000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
lsmod | grep "b43"
b43 137208 0
mac80211 155532 1 b43
cfg80211 90428 2 b43,mac80211
ssb 45988 1 b43
pcmcia 36168 2 b43,ssb
pcmcia_core 35184 5 b43,yenta_socket,rsrc_nonstatic,ssb,pcmcia
led_class 4000 3 b43,sdhci,acer_wmi
/etc/rc.conf
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(!b43 !ndiswrapper)
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
#eth0="dhcp"
INTERFACES=()
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
DAEMONS=(syslog-ng network netfs crond hal)
I've already tried many different configurations in rc.conf, but it still does not estabilish a connection in the first try.
I'm using the driver from the wiki (http://mirror2.openwrt.org/sources/broa … .5.tar.bz2) and did not try with only ndiswrapper. It's because I want to have all functionalities from criptography and... after all, it was supposed to work, wasn't it?
Where could be the problem? The driver version? Or bad configuration?
Thanks in advance!! If you need more information, please ask.

So, the same problem occurred and in a relatively shorter time than before. I began to think that something is causing this problem.
My theory is that it is a VMWare software issue. What I've been doing differently recently is using it in "Unity" mode as opposed to "Full Screen" mode. My guess is that the program is modifying my wireless permissions and screwing it all up.
So, what I've done is set the "Network Adapter" to "Host-Only". This denies the VMWare program internet access but still allows file sharing between the Windows virtual environment and the Mac hard drive.
Then I had to re-install Mac OS X all over again to fix the wireless settings/permissions mess.

Mac mini not keeping connection with Cisco wireless access point

I am trying to get my wife's Mac Mini to keep it's connection with the wireless network at her school. They are using a Cisco access point (not sure of the model) which works fine with my G4 Powerbook and the numerous Macbooks being used there, but for some reason her Mac Mini drops the connection after 4 or 5 minutes, at which point she needs to log right off for it to reconnect (as opposed to just turning the card off and on again). I have already gone through the deletion of the Networkinterfaces.plist file, and recreation of the Airport card profile process, but this only kept the interface active for about 36 hours, then it was back to the same old problem. At this point I am thinking "flakey card"...before I ship it off to Apple, can anyone offer any other possible solutions?

After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!

Ichat not staying connected with OS Lion

Hello, this week I updated my MacBook Pro to OS Lion (finally!) but now my ichat will not stay connected. It had been suggested in another chat discussion to force quit imagent within the Activity Monitor. I have done this multiple times with no luck. IChat still only stays connected for a max of 5 min! Any other suggestions? Thanks!
Melissa

Hi,
I would test some other situations ton see if you can "prove" it is somewhat linked to Mail or at least something the OS is doing regularly.
I would try different time settings in Mail
I would try iChat without Mail being Open.
The first may highlight it is the Check that Mail does that "upsets" the Internet.
The second may exclude the Mail App and highlight that it is something the OS is doing separate from that.
If you manage to exclude Mail as the cause then look in System Preferences > Date and Time and check if it is using a Time Server ? (in the Date and Time Tab/Button).
Does this fit with the Time Zone you are in ?
If they appear to be OK check the Date and Time settings in your Modem or router.
9:31 PM Thursday; March 22, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Lion 10.7.3)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

IOS 5.0.1 does not allow connection with my car's bluetooth. Is this similar with any of you?

After updating to the new ios 5.0.1, my iPhone is not connecting with my Ford Fiesta's bluetooth. But the old ios was working perfectly.

Delete the pairing on both the phone and the car, then re-pair them.

Number group not maintained for WITH HOLDING TAX challan

Dera frends can you help in solving the problem.
I have configured WHT it is posting well in vendor a/c and posting in tax account too. but while executing remittence challan System giving message " number group not maintained for CO code xyz section IEQEWT! and business places 194c.
where company code - XYZ
official withholding tax code - 194c
business place EWT1.

Hi
Pls follow the path
IMG>Financial Accounting (New)>Withholding Tax>Extended Withholding Tax>Postings>Certificate Numbering for Withholding Tax
Pls assign points if the information is useful to you
Regards
Sanil Bhandari

After having downloaded my e-book ADE gives the information that there is not a connection with internet. What is the problem? Liejaat.

After having downloaded my e-book, Adobe Digital Edition gives me the information that there is no connection with internet.Who can help me with this problem? Liejaa.Adobe Digital Editions

I've never seen this error in the context of trying to connect via ODP.NET or ODT.
If you have Oracle Dev Tools for Visual Studio installed, you can try to create a connection to the database using Server Explorer. If this works, that means your ODP.NET connection is just fine.
If you don't have VS or the tools, another thing you can try is connecting through ODP.NET using a simple OracleConnection.Open. Make sure you have your client set up to connect to the DB server.
Here's some info about connecting to the DB:
http://download.oracle.com/docs/html/B28089_01/featConnecting.htm#sthref101

Any way to NOT auto connect with wifi?

I connected to a WiFi that was near me. Turned out to be a Jack-In-The-Box wifi which requires you to be in the restaurant looking at their tv screen for a code to type in.. well, anyways its really annoying now when trying to get online and it hooks up to that signal!
Anyway to make it not AUTO connect to ONLY that WiFi signal?

When connected to the network tap on Settings/WiFi, then the arrow to the right of the network name, then "Forget this network"

Linksys WTR160N not keeping connection with internet

I just bought a Linksys WTR160N Broadband router and tried to connect with comcast modem Arris. Keep losing connection. Called linksys tech and he said it was my network card but when i connect direct to the modem it works fine. I bought a new linksys network N card for my laptop and it has the same problem. I am direct connected right now and has worked fine. HELP

Try to readjust the wireless settings on your router...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Reduce the MTU size to 1300 under setup..and Click on save settings.
For Wireless Settings, please do the following : -
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Built in Ethernet not staying connected with modem

Hi,
My old Power PC G4 will not say connected to my modem. I have never had any issues in the past, but if the G4 goes to sleep, or I turn it off, I have lost all settings and connections. I locked preferences, but nothing has worked. Is there something I am doing wrong? Is this a hardware issue?
Thanks for any help!
Matt

Hi Mateo, and a warm welcome to the forums!
Tough to tell if it's HW or not yet.
Sometimes having an all OFF Location can help, thanks to Gnarlodious...
http://gnarlodious.com/Computer/MacOsx/WiFi
Using network locations in Mac OS X ...
http://docs.info.apple.com/article.html?artnum=106653
Let's see if that reconnects first.
Also, a strange old cure for not connecting after awakening, was to turn off Automatic Login!?

BB LINK 123.2.3 Does not WiFi CONNECT with Q10 OS 10.2.1;1925

Upgraded to the current revision of LINK. Now, a Q10 v10.2.1 will not WiFi connect. Connection was solid on prior revision of LINK. I have tried re-launching LINK as well as cold and warm restart of the Q10.
Solved!
Go to Solution.

you updated your bb link to 123.2.3 and your q10 will not connect to wifi anymore? is that what you asking?

WMP300N's not maintaining connection to WRT300N

I have two WMP300N's connecting to a WRT300N via wireless, and several computers that connect via CAT-5. The WRT300N has DHCP enabled.
The computers connected via wire get an IP address just fine and everything in that regard is working fine.
The two computers connecting wirelessly are both a very short distance from the WRT. Both report "Excellent" signal strength (84% or better). And both of them CONSTANTLY lose their connection to the WRT about ever 2-3 minutes, then go through a period of reconnecting and getting reassigned an IP address. In the meantime, of course, any tcp connection I have established with a remote site stalls until the wireless computers can get their IP address back.
I have the latest firmware on the WRT, and the latest drivers on the WMPs.
Why are these wireless connections to flaky and, more importantly, what do I need to do to get a stable wireless connection established and maintained?
Is the "N" protocol still a garbage spec? Do I need to force it to drop back to an 11g connection to get something reasonably stable?

Hi
As you are facing frequent connection dropping issues, first of all make sure you hardwire one of your computers directly with your router, then launch Internet explorer and clear address bar and type in 192.168.1.1 and password as admin and then click ok.
Click on wireless tab and then change Radio band to Wide – 40MHz channel, Wide channel to 9 and standard channel to 7 or 11. Now check the connection. If you get good connection without dropping then no issues, but if not then again enter the router setup page and click on wireless tab and then click on sub tab Advanced wireless settings, reduce Beacon interval to 75, RTS Threshold to 2307 and Fragmentation Threshold to 2306 and save settings and now check the connection.

N5800 not maintaining connection with plantronics ...

Similar Messages

Maybe you are looking for