N7230 Slide, Battery Remove Problem

Hi,
I bought a new N7230 Slide, i open the back cover & , see the battery but i want to remove it to insert the sim card, how can i remove it is there any special button to press it to enable to remove the battery.
thanks a lot

turn phone on its back in palm of hand and tap gently
or read the getting started guide in manual
here
http://www.google.ie/url?sa=t&source=web&cd=1&ved=0CBYQFjAA&url=http%3A%2F%2Fnds1.nokia.com%2Fphones...
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Similar Messages

Sporadic high-speed fan behavior ––– removing battery solves problem?

Every so often, my fans will peg around 6,000rpm, even though the operating temp is around 120º – not nearly hot enough to trigger such fan action. I check Activity Monitor and nothing is hogging the CPU (Safari 5.0, kernel_task 3.3, pmTool 2.6, configd 2.4, etc. – these are pretty typical readings.) The % Idle is usually around 90%.
I just discovered that removing the battery solves the problem. Just one minute later, my fan speed is at 2003rpm.
It's driving me nuts, and (of course) when I take it to the Genius Bar, it won't replicate the problem.
Any ideas?

While I'm not sure what may be causing your sporadic fan behavior, running your MacBook Pro with the battery removed causes the system to significantly reduce the processor speed. That is probably why your system is running cooler with the battery removed... not because of any fault with the battery itself:
http://support.apple.com/kb/HT2332
You may want to reset your System Management Controller (SMS). The link below provides the details. Among the things this will address are fans that run at high speed although the computer is not experiencing heavy usage and is properly ventilated. Be sure to follow the instructions specific for your machine as they vary slightly from model to model.
http://support.apple.com/kb/HT3964?viewlocale=en_US

Satellite A60: battery charging problem

Hey,
I have a toshiba satellite A60 notebook. My notebook is 2 years old. After I used my laptop in battery mode, it fell out because the battery was empty. When I plugged it in on the net, the battery led flashed amber for less than a second and went out again. The battery won't charge anymore and the batteryled is out.
Windows detects the battery though. The laptop still keeps running on the battery for some minutes. I already had this problem a year ago and after a few months the battery started charging again.
Does anyone have a simular problem and how do you solve it?
Thanks (sorry for the bad english)

Hi
Possibly the battery cannot charge properly because it has a malfunction.
Generally the battery performance decreases in process of time.
I read that you can charge and discharge the battery about 500 times and then the performance goes down.
You can try to remove the battery for a several time. After this time try to charge it.
I would also recommend checking if this issue happens also with a new battery.
But its also possible that there is something wrong with the power supply electronic.
This could have a bad influence on the charging procedure.
I have also read that the BIOS update have solved some battery charging problems.
But if the battery charging has worked since 2 years so I assume the BIOS is ok.
However, check it with a new battery.

Hi, I was working at home with my iPad, everything was going well. It went out battery and after this I am unable to connect to the wifi at home. Before getting out battery no problem, and now it sees the router signal but it is unable to connect to it.

Hi, I was working at home with my iPad, everything was going well. It went out battery and after this I am unable to connect to the wifi at home. Before getting out battery no problem, and now it sees the router signal but it is unable to connect to it.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Yoga 3 Pro Battery Charging Problems

I've combined several discussions into one because there are multiple cross-overs of symptoms.
After reviewing all the posts, I see there are two types of problems discussed:
Battery charging but only to a certain percentage
Battery intermittently charging
Several people have reported success with their limited battery percentage problem by following the solutions suggested by MarinM and Vladtech.
For the intermittent charging, several people have reported that sometimes the battery charges, sometimes it doesn't. I'd like to dig into these reports. I have a few questions I'd like to ask.
When does it charge, when does it not?
Are there any patterns to this?
Does swapping electrical outlets make a difference?
Does the USB 2.0 charging port appear loose?
Does the cable show any signs of damage?
Does the AC adapter show any signs of damage?
When a second device is plugged into the extra USB port on the AC Adapter, does this impact Y3P charging?
Are there any battery error messages?
Thank you for your help,
4/6/15 EDIT: Moved message for escalation purposes. Amy_Lenovo
Amy Tupper
Technical Resolution Lead, Pervasive Issues
Lenovo US
ThinkPad T431s, S3 Yoga 14, Helix, Edge 11 & 14, E431, IdeaTab A1107, IdeaPad A1-07, IdeaCentre Horizon, Yoga Tablet 2 10 1051
First computer was a 1980 Commodore 64 from Radio Shack/ GEnie SFRT member from 1993-1996

I'd like to hear more about what happened to your Yoga 3 Pro not charging.
Did you call Lenovo Service or find another solution?
Thank you,
Amy Tupper
Technical Resolution Lead, Pervasive Issues
Lenovo US
ThinkPad T431s, S3 Yoga 14, Helix, Edge 11 & 14, E431, IdeaTab A1107, IdeaPad A1-07, IdeaCentre Horizon, Yoga Tablet 2 10 1051
First computer was a 1980 Commodore 64 from Radio Shack/ GEnie SFRT member from 1993-1996

My iphone 4s wifi on/off appear grayed out or dim i can not use and battery got problem with retain charge even not in use. and i am in india here no taking my product for repair . how i sort out this issue

Hi,
i bought iphone 4s in london but now return to india . right now i can not access wifi option because wifi on/off grayed out or dim . and also battery got problem to retain power it automatically loose power even not in use. i went to local apple service centre they said could not repair in india.they said talk to uk apple centre. so what i do now please any one give guidence .

You posted in the iPad forum instead of the iPhone forum. To get answers to your question, next time post in the proper forum. See https://discussions.apple.com/index.jspa I'll request that Apple relocate your post.
 Cheers, Tom

2nd dead iPod Touch 4G in 2 months? Battery/charging problems!

Hi everyone,
It seems as of tonight that I will have to return my second iPod Touch 4G in the last two months. In both cases, it was an issue where the device would no longer charge, and became very hot on the top of the back panel when the device was turned on even for a few seconds (while not being plugged in). In the first case, the device seemed to be defective from the time I opened the box, which was confirmed at an Apple Store, but they asked me to ship it to Apple Repair to be checked out. Apple took a very long time to get a replacement to me, but was good about that problem, and I was happy with the replacement for the past month when all of a sudden tonight the new one would not change and became very hot.
Is this an issue that anyone else has seen? I essentially only charged it off of my laptop or a wall charger unit, but it seems like the battery essentially is shorting out. I love this device, but actually need to use a PDA-type device enough that I am questioning whether I should get a replacement or go back to my old Palm TX.
Thanks for any thoughts/feedback on my iPod Touch 4G battery/charging problems.
Message was edited by: eliotjasper

Most battery complaints complain about loss of charge. The iPod is designed to lose heat through the back as the battery discharges. This is most common when using the device a lot - like playing games. If yours will no loner charge, by all means return it to Apple.
As far as being a PDA goes, it is as good as any smart phone out there. The PDA, as you once knew it, is dead and has been for 5+ years. Take your iPod to an Apple store and insist on a replacement.

I'm trying to resolve a battery usage problem

I'm trying to resolve a battery usage problem on my iPhone 5S ...
Have been working with an Apple agent via chat and I'm 99% certain it's a software problem, but I can't isolate wish software ...
So, I'm going to set up my iPhone up as new (when I did this as part of identifying where the problem is, it help its charge for 24 hours) but I have a problem with photos ...
I can see photos on my iPhone (restored from an iCloud backup) up to date, but on my iMac/iPhoto with my iPhone attached i) I can only see photos on my iPhone up to a date in the past (mid October 2014) and ii) iPhoto says all photos have already been imported ...
How can I (can I) get the more recent photos onto my iMac e.g. into a folder and then import them from there into iPhoto?
Also, why is the restore from an iCloud backup taking so long (it's been 14 hours now) when I'm pretty certain everything's now there that should be?

Just to add ... my real problem is that I can see photos on my iPhone, but in iPhoto with the iPhone connected, I can only see photos up to a certain date - weird?!!!

Is the 10.7.2 fixed battery drain problem ?

there is no information anywhere and I wonder if this problem is fixed ?

I wonder what percentage of users has that problem? Maybe I need to retest that one Unibody MacBook battery again with Snow Leopard, we always got poor life with Windows on it.
I will double check also the new 2011 MBP, unfortunately, we have no reference to what is a good battery life on that one. It is a new system. It definitely had no effect on our old white MB.
(Now I am having serious battery life problem with my 2010 Touch could that be an OS?)

Fix battery discharge problem?

I have been working with this for 2 weeks w/o success.
Lawrence Finch and others have helped.
First, I tried the battery recalibration and it seemed to work.
I could pass the " battery drain test".
That didn't last.
Now, when I redid the drain test, neither the usage time nor
standby time changed in 5 minutes - that's weird.
Next, I'll try Scotty's suggestions about Background ap refresh.
Following a suggestion, I upgraded this week to iOS 8.1
Alas, that failed, too.
After upgrading to 8.1, the problem remains.
After recharging my phone, I use for one or two calls, one or two messages.
Otherwise, it has been sitting.
During the first upgrade to 8.0.2 some weeks ago,
I added a pass code and downloaded NUMBERS, an app I use heavily on my Mac.
Could either of those be the problem?
I've searched the on-line manual for how to delete NUMBERS to no avail.
I just redid the"battery drain test" suggested weeks ago: noted standby and usage times, pushed the standby
button to put it to sleep, came back 7 mintues later. Result: no change in either standby or usage times.
Previously, I did get a result indicating a battery drain problem.
The battery is dead in 24 hours.
Should I give up and head for the Apple Store?
I'm really getting frustrated.
Thanks so much for your patience,
Thanks in advance for your help.
Many thanks for your previous responses and suggestions!!

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved.

Warning Hardware RAID ALERT: (0x0008/1) - Battery removed' (attempt #0)

Warning <Hardware> RAID ALERT: (0x0008/1) - Battery removed' (attempt #0)
Please, help me to understand what it means. Server Ironport c350. Every restart I can see this event in system.current in /system_log/

Hello Igor,
please open a service request with support, as your RAID battery (the battery on the RAID controller) requires a replacement here.
Thanks and regards,
Martin

Why the CPU Frequency will just stated at 1189MHz when the X230 had AC Power ONLY (Battery Removed)?

Dear All,
I bought a X230 (i7) notebook. I found that if removed the battery from the notebook and only use AC power with the X230 Notenook. The CPU frequency will stated at 1189MHz. It will not change no matter how many program the notebook is running. The CPU frequency will rise to 2.9GHz or upto Turbo when the Notebook with battery or battery and AC power. Why the CPU Frequency will just stated at 1189MHz when the X230 had AC Power ONLY (Battery Removed)? This is not right. Any setting in the X230 Notebook need to change? Please help.
Solved!
Go to Solution.

RichardW wrote:
The situation is probably the same as it was for the X220. A 65W power adapter by itself doesn't provide enough power to run the computer at full speed, but it can when combined with a battery. However the 90W adapter may be able to run the computer at full speed without a battery.
As it was with earler X-series. This is by design. It allows people to travel with the smaller, lighter 65W adapter. However for maximum speed and flexibility it's best to always use the 90W adapter.
Cheers... Dorian Hausman
X1C2, TPT2, T430s, SL500, X61s, T60p, A21p, 770, 760ED... 5160, 5150... S360/30

Labview slider event handling problems - revisited

This topic asked a question that was very close to a problem I am having:
Labview slider event handling problems
That is, how do I, using an event structure and/or other means, only read out the value of a slider control after the value change is finalized?
The extra constraint I'd like to place on this, which I believe will invalidate the answer given in the thread above, is that my slider control also has a digital display which can also be used to change the value without ever using the mouse. I cannot look for a value change followed by a mouse-up event if the mouse was not used to change the value.
Any ideas how this might be accomplished? FWIW, I am using LabVIEW 7.0

Each and every incremental value-change event generated by the movement of the slider is still detected and queued up for use by the event structure and the event structure loop wades through them all before it's done.
I have come up the attached "fix" (LV v7.0) for this problem. While it is not as clean a solution as I had hoped it would be, it's the best I can manage given what LabVIEW offers me to work with and it does work in the situation where I need to use it.
Now, within the Finalize Slider Events subVI, I'm keeping track of the most-recent values seen by the subVI, checking to see if they have changed, and reporting out that fact. That gives me a Changed/Not-Changed bit within the event case that I can use to control what code then gets executed. If the event case is just playing catch-up to the real value of the control, I can now see that fact and ignore it.
In this version I've also dumped the variant output and limited the VI to using DBL values. I decided it added complication to something that was too complicated already and I wanted the output terminals for other purposes anyway (reporting of the correct "OldVal" of the control).Message Edited by Warren Massey on 04-28-2005 03:56 AM
Attachments:
slider_events[5].llb ‏77 KB

Nikon Coolpix L100 Battery Exhausted Problem

Hi,
I have recently bought a new Nikon Coolpix L100 Camera just 6 days back from a Best Buy Store. I am running with Battery Exhausted issue for each turn on. Even I tried to change the new battery , the problem doesn't change any behaviour and the outcome is remain same. I am really helpless to find out the cause of this problem whether this is a problem with the Camera or with Battery. As I have purchased this recently , I would like to replace this.
Please help me out on this.
Thanks in Advance,
Anil

Hi anilkhamari,
If you've tried using brand new AA batteries, and you continue to have issues with your new camera having no power, Nokia is most likely correct that your camera is defective.
With that being said there are certain measures you can take to conserve battery power, and enhance how long your camera has power. First thing you could try is using Lithium AA batteries. This type of battery will have a much longer charge than the average alkaline battery. The LCD is the part of the battery that uses the most power by far, and there are usually settings on a camera that can save power by adjusting the brightness level of its LCD. I would also suggest you make sure the power button is always turned off while the camera isn't being used, and that it isn't inadvertently being turned on while in your camera bag.
If you do feel like your camera is defective you should be able to return or exchange the purchase as long as it was purchased in the last 14 days, and the purchase is older than 14 days you should be able to get it repaired by the cameras manufacturer's warranty. I would suggest bringing it to your local Best Buy® store, and they should be able to take care of you.
I hope this helps!
Allan|Senior Social Media Specialist | Best Buy® Corporate
Private Message

MBP with battery removed- CPU runs slow?

I'm working on a project today on my MacBook pro with the battery removed.. The battery kind of exploded and warped out of shape which I only noticed last night, luckily apple have a recall program that covers my model of machine so I'll get a free replacement in a couple of days. Anyway, meantime I'm working on a pretty intensive project with a lot of stuff going on in terms of plug ins and instruments etc. Running it in no battery mode with just the power adapter, I'm noticing the CPU bars are pegging pretty hard. I know it's a busy project but I could've sworn it was hardly pipping the CPU's before. Then I remembered reading somewhere that if you use a mac notebook with no battery plugged in the CPU max speed is automatically limited to 1ghz or something.. But I'm not sure if this was some kind of folk tale or actual fact. Anybody have any ideas about this? I don't get my new battery for a couple of days and i'd sort of like to have logic running normally in the meantime if possible...

4 month I was working without the battery in my new MBP, because I thought to preserve it when using the MBP at home. I was so dissapointed with the performance that I thought about selling the MBP again. Just by accident I found a note in a forum saying: if you remove the battery, the tact of the CPU goes down to 1Ghz. I went back home to put the battery back in and I had the power I was expecting. Suddenly all PlugIns were easily handled by the MBP. I was surprised that so few people know about this. So yes: take out the battery and you won't even have half the power (if you have more than 2 GHz).
Cheers!

N7230 Slide, Battery Remove Problem

Similar Messages

Maybe you are looking for