N73 ME Always Network Busy Problem..?

I have a N73 ME mobile. When I try to call somebody, mobile always showing the message "Network Busy". If anybody trying to call may mobile, saying that "line or mobile is busy" . Please help me ..?
Version
V 4.0727.2.2.1
04-07-2007
RM-133
@Nokia N73(08)

ok
take sim card out wipe it with a dry cloth and place it back into the phone, then go into settings and check which mode the phone is currently in UTMS or GSM.
make sure u got it on gsm and then try to make a call...
Blackberry Bold

Similar Messages

7921's getting network busy when WMM enabled

WLC 4404 running 4.1.185.0
7921's running 1.2.1
CUCM 6.1
If WMM is enabled the phones cannot dial, they just get "NETWORK BUSY" messages on screen. CAC settings don't matter, but if WMM in the WLC is set to anything except DISABLED then it doesn't work.

I believe you will find it there per default, if you enabled CAC through the GUI.
Please refer to "Cisco Wireless LAN Controller Configuration Guide, Release 4.1". See "Chapter 4 - Configuring Controller Settings" and look for "Using the CLI to Configure Voice Parameters". When doing a "show running-config", verify that all parameters from the guide are present and set to the correct (i.e. default) values.
http://www.cisco.com/en/US/docs/wireless/controller/4.1/configuration/guide/c41ccfg.html#wp1091874
I'm not sure I understand why it should be a problem with the controller being on a remote site. The Command Line Interface is remotely accessible through telnet or ssh. Only Console access requires physical access to the box. See "Chapter 2 - Using the Web-Browser and CLI Interfaces"
http://www.cisco.com/en/US/docs/wireless/controller/4.1/configuration/guide/c41intf.html#wp1097698
I don't think it's necessary to upgrade the firmware in this case. If you however do so, you can always downgrade again. Just read the relevant release notes and articles.
Good luck.

My daughter has just bought me an iPad 2 from Dubai and set it all up for me but unfortunately the iMessage function doesn't seem to work. We keep getting messages,when trying to activate it, that there is a network connection problem - help!

My daughter has just bought me an iPad 2 from Dubai and set it all up for me but unfortunately the iMessage function doesn't seem to work. We keep getting messages,when trying to activate it, that there is a network connection problem - help!

Thank you both for your responses but my daughter was reassured by the salesman in the iStyle store (official Apple store in the UAE) that iMessages would work but conceded that FaceTime wouldn't. My iTunes account is registered in the uk and my daughter's iPhone has iMessages even though she bought it (and uses it) in Dubai. Can anyone else throw any light on this?

Firefox have some promlems and it block when is opeining hotmail, in my laptop always have that problem, so i need check my email using another programs...that problem is in my laptop or it´s a problem of navigator??

Firefox have some problems and it block when is opening hotmail, in my laptop always have that problem, so i need check my email using another programs...that problem is in my laptop or it´s a problem of navigator??

I know you can't help with my Yahoo problem, however, apparently at some time in the past I have went to the Sync and tried to figure it out on both my laptop and my desktop, because I have the long snyc key information. However, when I go to try to sync both computers I never get the box to enter that key on either one. That is my problem. So should I try and get a new sync key and see if that works.

My Skype Number always shown busy when call

Since I bought my skype number it is always shown busy. Can you help?

Hi, Psalamon, and welcome to the Community,
Please contact customer service to request assistance with this.
Also, when you say, "My skype number is constantly busy when I am called (and I am not using it!),"
... please note that the Skype Number will not "ring busy" - if you are using Skype, incoming calls would be diverted according to your Tools -> Options settings. The Skype Number provides a phone number for people to reach you, but the number has nothing to do with outbound calls you place.
Hope this makes sense!
Regards,
Elaine
Was your question answered? Please click on the Accept as a Solution link so everyone can quickly find what works! Like a post or want to say, "Thank You" - ?? Click on the Kudos button!
Trustworthy information: Brian Krebs: 3 Basic Rules for Online Safety and Consumer Reports: Guide to Internet Security Online Safety Tip: Change your passwords often!

Always have a problem ,every month two or three times all my contacts DISAPPEARS

Always have a problem ,every month two or three times all my contacts DISAPPEARS

Betewen all i save all my contact in I cloud ,any the same DISAPPEARES !!!
After 2 day rutern show all my contacts !!!
what's the problme ??

Regarding Adobe form for development but the ADS always has a problem

Hi,
Currently we are using Adobe form for development but the ADS always has a problem in EC6 as below.
Test Program: Version Information (for Analysis Only)
System Error
ERROR CODE: 100.101
ERROR MESSAGE: SOAP Runtime exception: CSoapExceptionTransport : HTTP receive failed with exception communication_failure
SOAP Framework error: SOAP Runtime Exception: CSoapExceptionTransport: HTTP receive failed with exception communication_failure(100.101).
Would you pls help to figure it out?
Thanks & Regards,
Suneetha

Hi,
It seems that you ADS settings have not been maintained,
check the note
944221 Troubleshooting if problems occur in forms processing
Hope this resloves your issue,if not revert back.
Regards,
Vamshi.

SOLUTION TO BUSINESS PROBLEM IN INVENTORY

Hi all
PROBLEM DESCRIPTION:
When a driver from the warehouse/Inventory collects all the goods to distribute them to different stores He signs the paper and then leave. This signing of the paper is creating a lot of problem as they have to keep this hard copy and this in turn is piling up. any solution to this business problem.
thanks a lot in advance.

To make a long story short, I went through 5 MacBooks before getting my macbook pro. I exchanged them for various reasons (they were all Rev A, just after they came out). Three out of the five had the vibration problem. Two were rock solid, but had other problems. I sent in one of them that had the vibration specifically to have it fixed. It came back with a new HD, and still vibrated like crazy. My guess is that some unknown part of the build process randomly makes some of the cases unable to dampen the hd vibration. It's just luck of the draw. If you really want to get rid of it, I suggest sending it in repeatedly. If they don't fix it in three tries, you will be the proud owner of a brand new macbook, which hopefully, won't vibrate. Good luck.
Also, if you want, look up some of my previous posts, I have posted on this many many times in the past.

Network Accounting Problem

I have a serious network accouting problem arisen from content engine:
Our routers are connected to internal backbone router with enabling Netflow to bill the usage (from domestic to backbone) of each users.
However, the CE will affect the network accounting seriously because it will replace the sender IP address with its own address before sending out to the link.
Would you give me some solution to remedy the problem?
Very Very Urgent!!
Thanks a lot..
Alex

Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.

Having issues with picture messaging get told to go to settings, then general, then network then cellular data network. my problem is there is no such option my phone is a 3gs

having issues with MMS messaging instruction for setup, are to gotto settings, then general, then network then cellular data network.My problem is there is no cellular data network optiion on this page have tried resetting phone , no good .Help.

That option does not exist depending on who the carrier is.
Who is the carrier? Are they a supported carrier?
Have you tried Settings > General > Reset > Reset Network Settings?

Network Extender problems w/Qwest customers during July 2011

I believe I have found the cause of the Network Extender problems surfacing in July, 2011. I am a customer who has been out of Network Extender usage for two weeks now. Read on....
Unbelievably, almost no one at Qwest, Verizonwireless, or Samsung (NE's manufacturer) has any idea what the cause is and neither Qwest nor Samsung knows that a problem exists at all.
After many hours on the phone to all three companies I finally believe I know the cause of the problem. The cause is an updated firmware revision that was pushed to all Qwest customers who use the Actiontec PK5000 modem/router. They have been pushing it out over the last few weeks, so the symptoms have been rolling rather than happening all at one time.
The latest version of the PK5000 firmware is QAP002-3.60.3.0.9.9 When the customer's modem receives that version update (unbeknownst to them), Network Extender is rendered inoperable... the modem does not recognize the NE is plugged into it and does not provide an IP address. The WAN light goes solid red, the GPS goes magenta and the SYS light goes red.
Because Qwest's PK5000 works fine with the upgrade (i.e. both wi-fi and ethernet connections work fine with my Macintosh MacBook Pro), they have no interest in solving my VerizonWireless problem.
Bottom line is VerizonWireless needs to get a patch created "yesterday" and made available to all Network Extender customers who use the Actiontec PK5000 Qwest modem/router immediately. I live in a rural area and despite the fact I've had a VerizonWireless cell phone for many, many years, I'll be forced into changing cell phone providers soon, as will every other NE user who has lost their NE usage because of this problem.
It boggles my mind that no one has figured this out and provided a patch for the Network Extender. Understandably, Qwest could care less this is happening, since their service is not effected. This is truly VerizonWireless' problem.
Now, what can you do??? Call customer service right now and get technical support. Give them the information above and let them know they need to develop a patch for the Network Extender to work with the new firmware (i.e. operating system) of the Actiontec PK5000 modem. It's only when they hear from a bunch of people that they will step up the urgency to find a solution. Thanks!

OK, what's the deal here. I've been having the same problems. Verizon gave me a new extender and I still have the same problem. The week of July 15th everything went dead. I live in downtown Denver and I still can't get service at my house. My network extender is no longer compatible with the PK5000 modem QWEST issued. Firmware got pushed out? uhh... OK that doesn't mean anything to me. Not my problem, but kudos to the gentlemen who figured that out.. Neither Verizon or qwest seem to not want to take responsibility.
So what's next? is there an extender on the market that is compatible with the infamous PK5000? Evidently, the guys @ Qwest I was on the phone with for 45 minutes seems to think it's some type of high speed low drag, technological phenomenon. I'd like to add that if someone from qwest or verizon tech support reads this, I do not have a land line at my house, I have never had a land line at my house so no I can't go to my desktop and troubleshoot the modem while on the phone. just to reinterate I live in downtown denver I do not have cell coverage at my house, and no it's not my house. Everyone in our area does not have coverage.
I've had verizon for over 10 years now and never had a problem. This is the first and biggest problem I had becasue verizon and qwest decided to "bundle" thier service offering...whatever that means.
I believe I have found the cause of the Network Extender problems surfacing in July, 2011. I am a customer who has been out of Network Extender usage for two weeks now. Read on....
"Unbelievably, almost no one at Qwest, Verizonwireless, or Samsung (NE's manufacturer) has any idea what the cause is and neither Qwest nor Samsung knows that a problem exists at all.
After many hours on the phone to all three companies I finally believe I know the cause of the problem. The cause is an updated firmware revision that was pushed to all Qwest customers who use the Actiontec PK5000 modem/router. They have been pushing it out over the last few weeks, so the symptoms have been rolling rather than happening all at one time.
The latest version of the PK5000 firmware is QAP002-3.60.3.0.9.9 When the customer's modem receives that version update (unbeknownst to them), Network Extender is rendered inoperable... the modem does not recognize the NE is plugged into it and does not provide an IP address. The WAN light goes solid red, the GPS goes magenta and the SYS light goes red.
Because Qwest's PK5000 works fine with the upgrade (i.e. both wi-fi and ethernet connections work fine with my Macintosh MacBook Pro), they have no interest in solving my VerizonWireless problem.
Bottom line is VerizonWireless needs to get a patch created "yesterday" and made available to all Network Extender customers who use the Actiontec PK5000 Qwest modem/router immediately. I live in a rural area and despite the fact I've had a VerizonWireless cell phone for many, many years, I'll be forced into changing cell phone providers soon, as will every other NE user who has lost their NE usage because of this problem.
It boggles my mind that no one has figured this out and provided a patch for the Network Extender. Understandably, Qwest could care less this is happening, since their service is not effected. This is truly VerizonWireless' problem.
Now, what can you do??? Call customer service right now and get technical support. Give them the information above and let them know they need to develop a patch for the Network Extender to work with the new firmware (i.e. operating system) of the Actiontec PK5000 modem. It's only when they hear from a bunch of people that they will step up the urgency to find a solution. Thanks!"

Always had no problem syncing iPod but now when I connect to computer it says iTunes detects a device but can't verify properly. Nothing is appearing under devices or on right hand side it's not saying "privates iPod" anymore to drag songs to.? Help

iPod not verified properly in iTunes a device is detected. Then on right hand side of computer screen doesn't say privates iPod anymore to drag songs to from my library ? Under devices nothing is ther ? Always had no problem? iPod doesn't even beep when plugged in or automatically backup anymore because iTunes sees a device but not sure what it is? What happened? I've tried 3 different cords too!

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- See if another computer sees the iPod in iTunes
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

T41 has Network Controller problem

I was given a T41 2373-7JU that I loaded with XP Pro. My problem is it will not connect to the internet via it's browser. In Device Manager it shows a Network Controller problem and I've been unable to correct this no matter how many different drivers I've tried. Also, how do I tell if there's an internal wireless card inside? It did connect to the internet earlier today using my USB adaptor but now I can't even do that anymore. I've tried a dozen or so solutions without any success so where should I go from here?

Hi and welcome to the forum!
Following are the drivers you need for Ethernet and wifi card (and yes, as per support page there's an internal card installed in your system):-
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62922
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-42683
To install the drivers successfully, you need to run the .exe setups from C:\Drivers.... for each device after the first setup completes.
For ethernet, the setup is in C:\DRIVERS\Win\ETHERNET\PRO1000\Win32 and for wifi C:\DRIVERS\WLLANCSC.
Hope this helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

When i enter my apple id into i message it says it has a network connection problem even though it has full internet?

when i enter my apple id into i message it says it has a network connection problem even though it has full internet?What can I do???

See my response to one or your three posts.

I am trying to install free apps but I always get billing problem? Payment Method!!?

I am trying to install free apps but I always get billing problem? Payment Method!!?

Likely because you are trying to create a Mac App Store account with an existing Apple ID. The None option often is not available in that case. If you create a new Apple ID and iTunes/Mac App Store account following these instructions carefully, you will be successful in getting free apps without a payment method.
Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card -
http://support.apple.com/kb/HT2534

N73 ME Always Network Busy Problem..?

Similar Messages

Maybe you are looking for