N73 problem with access point.

I have 3 APN : orange mms, orange wap and orange internet. I deleted the orange internet apn (from tools settings connections) and set the phone browser to use the orange wap apn. My problem is that periodically the Orage Internet apn appears again in the list and the browser automaticaly switches to that one. The browser does not have any option to ask on connection. In the last 2 days I browsed 20 mb on the internet without knowing that it is internet not wap and this will cost me 25 $.
This is the most stupid thing I've ever seen, the phone lets you change your settings but it does what it wants (stupid factory settings).
Any ideas/ solutions?

Is your phone locked to the Orange network or did you buy it SIM free? Seems like typical behaviour for a phone with firmware designed for Orange.

Similar Messages

  • Problem with Access Point app

    Yesterday I experienced a problem with my internet sharing where it wouldn't start and gave me an error: Connection not shared, Internet sharing isn't currently available
    . I ran across an article on wpcentral.com where they suggested installing the Access Point app from this thread:
    http://discussions.nokia.com/t5/Pool-of-Knowledge/Nokia-Windows-Phone-8-App-Updates/td-p/1640082
    Now I've done that and I see 3 profiles in the app, only 2 are LTE. Activating either of those LTE profiles now gets me an error when trying to internet share that looks like this: Connection not shared, To enable tethering on this device, go to att.com/mywireless or dial 611. When I use the 3g access point profile I get the same message I was getting yesterday.
    At this point I don't think this app is doing anything for me. I dont' use multiple sims, I'm not a world traveller. I also don't know which profile I should be on. I'm clearly in over my head and would like to just take a step back. However, I can't see a way to uninstall the app as it's now in settings. How do I get myself back to where I was yesterday?
    And for bonus points, does anybody know what the original error I was getting means?
    Thanks,
    Joel

    Hi Adrian,
    Yes, I've tried a soft reset to no avail. I've gone to both the AT&T store and the Microsoft store and neither of them have any thoughts on what's going on. At this point I think I will need to replace the hardware since I've not found a solution from anyone.
    Thanks for you help.
    Joel

  • Intermittent problem with access point (WAP321)

    We hane an intermittent problem with our Wifi access point WAP321. Suddenly, all clients are unable to access Internet, server and local network. The signal is 100%. The message is no internet connection or limited connection (on all device, Iphone, computer, etc.). When I check to Ip configuration, the ip adress have change for loca 169.x.x.x. The only way to resolve is to reboot the access point. (POE).
    It seem that access point don't relay information to rest of network. Strange.
    The access point is connected to a simple unmanaged switch. This switch is connect to router and server. The serveur (Win2008) is the DHCP Server and DNS Server.
    Can you help me to find a solution. ?

    This may be the problem;
    Devices: WAP discovers devices with ASSOC method that don't have an IP
    CSCtz20891
    Description
    Symptom:
    The OnPlus topology will show nodes with no IP address. Devices associated to WAP121/321 VAP/SSID not on the management VLAN will display topology nodes with with no IP address.
    Conditions:
    This occurs when the client associated to the WAP121/321 but is on a VLAN other than the management VLAN. In this case the WAP client information can be collected on the management VLAN, but the clients cannot be ARP/ping to validate.
    Workaround:
    None

  • Problem with access to SipFactory from jsp-pages in JBoss environment

    Hello!
    I have an installation of the OCMS 10.1.3.3. deployed into a JBoss (jboss-4.0.5.GA) environment. Unfortunately I have a problem with accessing the SipFactory from a jps-page. Encouraged by the "messagesender" example I tried to get an instance of SipFactory from my jsp-page simply by calling:
    SipFactory sipFactory = (SipFactory) application.getAttribute(SipServlet.SIP_FACTORY);
    But unfortunately there seems to be no attribute "SipServlet.SIP_FACTORY" and I only get a null pointer. I have also tried running that code in the orignal messagesender example but it didn't work either. So I wonder if this should definetely work in a JBoss environment or if this might be a known problem. Is there anything that I could check/do regarding this problem? I suppose there must be an oracle module which should take care of making the SipFactory availabe after it is deployed. Perhaps something went wrong during the deployment?!
    Best regards,
    Tim

    Hi
    On JBoss, OCMS does not support converge applications.
    I.e the SipFactory can be retrieved from the servlet context when running on OC4J.
    Instead the SipFactory can be found in JNDI as described in the Developer's Guide:
    "External Access to SIP Servlets
    To enable convergent applications between SIP and HTTP, the OCMS Container allows you to get access to the javax.servlet.sip.SipFactory by looking it up through JNDI. The SIP Factory will be registered under the same name as the display name of your SIP servlet as illustrated in Example 2–12. The <display-name> in the sip.xml in this case must be "My sip app".
    Example 2–12 Accessing the Data for a SIP Session through JNDI
    InitialContext ic = new InitialContext();
    SipFactory sipFactory = (SipFactory)ic.lookup("sip/My sip app");"
    Cheers
    Lucas Persson

  • Problem with decimal point in Korea and Japan

    Hi all,
    I have one problem with decimal points.
    I need to change in my out put cuurency values as per japan or korea standards.
    Please help me is there any function module for this one.
    program using alv grid display.
    i use write statement but it is not working. Because
    data: L_AMT  type glpca-hsl,
             G_AMT  TYPE CHAR15.
    CURR this value is 'JPY'.
    WRITE L_AMT CURRENCY CURR TO G_AMT.
    here i need to do
    L_AMT = G_AMT.   "" going to runtime error.
    if i taken like
    data: L_AMT  TYPE CHAR15,
             G_AMT  TYPE CHAR15.
    CURR this value is 'JPY'.
    WRITE L_AMT CURRENCY CURR TO G_AMT.   "" it is not working
    Regards
    margani

    Hello,
    This is pretty basic, whenever you've currency & quantity fields you need to pass the corres. reference fields.
    In your case you need to populate the cfieldname & ctabname fields of the FieldCat.
    BR,
    Suhas

  • Problem with Access Policies (create multiple resources)

    I'm having a problem with Access Policies:
    The first policy must create a resource.
    And the following policies should create childs on the resource.
    The problem here is that when policies will add the childs, the resource is not provisioned yet.
    And then each one will create a resource but i just want one resource with the childs.
    When the resource is already provisioned, the policies update this resource properly.
    How can I fix this?
    tks

    Ricardo,
    I had a similar problem. In a post-process handler I was managing the user membership in specific roles through the removeMemberUser and the addMemberUser of the tcGroupOperationsIntf class.
    The last parameter of this method was a boolean which, when true, would automatically trigger the access policies programmatically in the post-process.
    The problem is that there also is an OOTB event handler for triggering access policies, so I was basically triggering the access policies twice and duplicated resources were appearing.
    Hope this helps.
    Cheers

  • Problem with access to SMTP, IMAP, POP3 protocols in CAS 2013.

    Hi,
    we have problem with access thgrough SMTP, IMAP, POP3 protocols in CAS 2013.
    If I test connection to SMTP 25 port from other computer, session end quickly.
    Test from CAS2013 to localhost or public IP is OK (similar also for IMAP and POP3).
    Receive connectors are with defaults settings, firewall is disabled.
    Service Microsoft Frontend Transport Services restarted, but no success.
    Certificate is assigned to IMAP, POP3, SMTP, IIS.
    IIS and HTTP(s), protocols are OK. Clients can connects only thgrough web, mobile (ActiveSync), or with Outlook with proxy.
    Do you have some tip, what to test?
    If I create new testing receive connector on port 26 for anonymous, behaviour is same, quick disconnecting.
    Thank's Mirek

    Hi,
    Pleaser try to use the following link to test your STMP/POP/IMAP e-mail, and check the test if successful:
    https://testconnectivity.microsoft.com/
    If unsuccessful, please check the test result, it will tell us what caused the problem.
    Thanks.
    Niko Cheng
    TechNet Community Support

  • Subject: FlexConnect compatibility with Access Point

    Subject: FlexConnect compatibility with Access Point
    Summary: Hi,
    We have today one Cisco 5508 and those access point on remote sites
    o CISCO AIR-LAP-1131AG-E-K9
    o CISCO AIR-LAP-1231G-E-K9
    o CISCO AIR-LAP-1142N-E-K9
    We plan to use redundancy on the controller and implement Flexconnect on the remote site. What we need to know is if I can implement Flexconnect on all actual access point - I think it is possible on 1142N + 1131G but do not know on 1231AG - is it correct or I'm wrong
    We plan to install the latest SW version for 5508 controller.
    Thank you
    Jean

    Here is what is supported
    Note All features discussed in this chapter apply to indoor (1040, 1140, 1250, 1260, 3500) and outdoor mesh access points (1500 series) unless noted otherwise. Mesh access point or MAP is hereafter used to refer to both indoor and outdoor mesh access points.
    Link to the guide
    http://www.cisco.com/en/US/products/ps11635/products_tech_note09186a0080b7f141.shtml
    Sent from Cisco Technical Support iPhone App

  • Problem with Vanishing Point

    hello!
    I've got a problem using Vanishing Point filter in Photoshop CS4. When I load this filter an error message pops saying "The operation could not be completed"
    I attach a screen cap of the error. Somebody can help? thanks.

    I run into this problem with Vanishing Point on about a quarter of the files I run the filter on. I can initially create a grid and do one transform, but the next time I try to run the filter I get the error, "The operation could not be completed". Then the error seems to stay attached to the file. I can run the filter on another file, but even if I close and reopen the file, I still can't run the filter. Even doing Save As and renaming the file doesn't rid it of the error.
    This has been the case since VP was introduced. I'm now on CS4. MacPro Dual-Core, 8GB Ram.
    I've tried changing the memory allocation to 55% with no change.
    I see that this has been addressed before in the Forum with no solution, Chris Cox care to wade in?
    This is a potentially valuable tool if it were implemented better.
    Craig

  • I have problem with Access Connections on L412 after that utilyty upgrade

    I have problem with Access Connections on L412 after that utilyty upgrade in early August. Windows 7 Ultimate/x64.
    It stops connecting to WPA2 Enterprise (AES-CCMP), Microsoft PEAP, no server cert, with any credentials I try to use. The same account(s) works with native Intel manager on other notebooks and on mobile devices. I lost the wireless connectivity to enterprise WiFi network.
    And, after deinstallation of Access Connections, the inability to connect keeped intact with native Win7 WiFi management.
    I think, something was broken in Access Connections 5.83 Build 83C753WW and some registry settings/ dll modules were altered but not returned to normal after deinstall.

    Access Connections is definitely broken for WPA encryption.  Both versions 5.02 and 5.84 fail for me.  If I use the Windows XP wireless configuration instead of Access Connections, everything works.
    Does anyone know how to report this to Lenovo?  I chased links around the web site but couldn't find a place.

  • Why do i have a problem with accessing images in adobe muse

    why do i have a problem with accessing images in adobe muse ??????!!!!!
    i need heeeeeelp ASAP
    pleeeeease

    I am on the begining stages with constructing the web so i do not have yet URL. The problem is i can not insert any image any way. Whether by fill a browser or by place image, i have the same issue. All the images with all image's format unable to be selected and it is turned off
    I really need help plz
    Is there any info i can supply that would help you figiring out the problem ??

  • Can Play iTunes Library from PC on MacBook Air but cannot import, problem with access rights?

    I can play Itunes library from Windows Vista PC on my MacBook Air using homeshare but cannot import the library . Error message is problem with access rights. Latest OS and Itunes installed. Both computers registered with Apple on same Apple ID. Wifi Router turned on and off. Still does not allow importing. Any suggestions please?

    Might be an alternative for you here > iTunes: How to move your music to a new computer

  • Just wondering if anyone has a problem with accessing iTunes store. have iTunes installed but can't bring up the store home page?

    Just wondering if anyone has a problem with accessing iTunes store. have iTunes installed but can't bring up the store home page?

    i have the same problem! Safari won't work either. Can anyone help please? I have completely restored my computer trying to fix this and it still won't work! I have a 2 month old alienware laptop running windows 7

  • N73 & Problem with Lifeblog

    Not sure if this should have gone in here, but here goes...
    I bought an N73 on 3 in the UK a few weeks ago, and Lifeblog was working fine. About a week after I had the phone, my old number was ported over, and several programs stopped working, one of them is Lifeblog.
    When I go to the lifeblog site to redownload lifeblog, the site says Lifeblog is installed on the phone, lifeblog is also listed in PC Suite (6.84.10.3), but when I run lifeblog, and click "copy new iteems from phone", I get the message that lifeblog is not installed on the phone, nor is there any sign of it on the phone any more.
    I have redownloaded the lifeblog installer exe several times and run that, but it still is not working, and run the installer from the CD that came with the phone - does anyone have any ideas ?
    Thanks
    (I am running Vista)

    Hey
    Thanks for replying!
    I've done some more experimenting, both with my old N70, and my new N73...
    The thing with point 1 is, on my N70, it does remember the album it was in, although you have to update the lifeblog app on the device itself, before you can sync to the PC, and the lifeblog on the N70 doesn't remember the mobile phone cell the photo was taken in. My theory is that the lifeblog app on S60 ver2 is subtly different to the one on S60 ver3 (obvious, I know, but the devil is in the details).
    The problem with point 2 is that it seems to have a preference for day notes over appointments ("meeting" ) in the recording. Since you ask, I use Outlook 2003 for my diary, and then sync to the N73, although sometimes I add appointments to the phone, or modify them. I don't really know whether that would make much difference, though. I use day notes, spread over the week, to record what week of the semester it is, and then meetings to record my lectures. I *was* hoping that it would record the lecture name, so I wouldn't have to cross-reference with my timetable to work out what lecture the photo was from.
    As a side note, I really like using the camera to photograph the board in lectures, and the lecturers don't mind, as long as the flash doesn't go off. Saves me furiously writing stuff down!
    Anyway, now that I know its the difference between my N70 and N73 thats making the difference, I'm a lot happier. I know I'm not going mad, and that there are quirks and bugs, but I dont seem to be able to find people discussing them. I've even looked on AllAboutSymbian and other, more fringe websites, but maybe I'm the only one using lifeblog like this.
    Cheers
    Tom

  • I am having problems with accessing Facebook because of Adobe. Is anyone else having this problem? What should I do?

    I am having problems opening Facebook, and You Tube. The sites will not open and a page comes up saying I need to update my Adobe Flash. The Adobe Flach is already updated. What should I do?

    The update alerts are fake, and are intended to mislead you into installing malware and/or to steal your identity.
    You might get the alerts when visiting a website that has been hacked. Don't visit the site again. If applicable, notify the site administrator of the problem, but don't send email to an unknown party.
    If you get the alerts when visiting well-known websites such as Google, YouTube, or Facebook, then they're the result of an attack on your router that has caused you to get false results from looking up the addresses of Internet servers. Requests sent to those sites are redirected to a server controlled by the attacker.
    The router's documentation should tell you how to reset it to the factory default state. Usually there's a pinhole switch somewhere in the back. It may be labeled "RESET." Insert the end of a straightened paper clip or a similar tool and press the button inside for perhaps 15 seconds, or as long as the instructions specify.
    Then go through the initial setup procedure. I can't be specific, because it's different for every model. The key points are these:
    1. Don't allow the router to be administered from the WAN (Internet) port, if it has that option. Most do.
    2. Set a strong password to protect the router's settings: at least ten random upper- and lower-case letters and digits.  Don't use the default password or any other that could be guessed. Any password that you can remember is weak.
    3. If the router is wireless, or if you have a wireless access point on the network, use "WPA 2 Personal" security and set a different strong password to protect the network. If the router or access point doesn't support WPA 2, it's obsolete and must be replaced.
    During the time the router was compromised, you were redirected to bogus websites. If you ever connected to a secure site and got a warning from your browser that the identity of the server could not be verified, and you dismissed that warning in order to log in, assume that your credentials for the site have been stolen and that the attacker has control of the account. This warning also applies to all websites on which you saw the fake update alerts.
    If you downloaded and installed what you thought was a software update, ask for instructions.

Maybe you are looking for