N8 GPS can't find my position

Hello
I have a big problem with my N8 GPS. I just use Integrated GPS in positioning methods and I disabled A-GPS, Network and Wi-Fi options. But Ovi Map 3.04 can't find my position. I compare my phone with an N79 and a 5800 in similar situation. They can easily find the position in less than a minute! But my N8 still searching and searching…. . It’s embarrassing!!!
Can anybody help me?! Any suggestion?

Grrr ! All that "experts" here...
1, Use AGPS if you want to get a coarse estimation of your position.
2. Use internal GPS only if you want to get a precise position.
3. There are no (NO !) differences in position fix speeds caused by software. GPS works in a sequential way: A sequential data stream is sent by the satellites. To get a full position fix, all of that data stream has to be received, from start to end. THIS causes speed differences: If you start the GPS application at the beginning of the data stream, fix is fast. If you start it in the middle of the stream, the device has to wait for the stream starting again from the beginning. This is for collection "almanach" data - data about where the satellites are at present - they're moving.
4. If that almanach data was received earlier and no too long ago, GPS fix is fast because the device does not have to wait for that almanach data stream. Again: It has NOTHING to do with different software.
By the way: This is what AGPS does - downloading that almanach data via internet instead of waiting to get that data via the air and trying to triangulate your coarse position with the help of comparing the signal strengths received by different cell towers. Again: This does NOT provide you with precise positioning data - just estimations. Never use AGPS if you need a reliable position fix. .
5. GPS signals are high frequency signals. Reception of such signals may vary greatly with the phone's position: One or two cm of placing difference may cause a big change in reception.
6. GO OUT ! Do NOT try the GPS module indoors. You MAY get sufficient signal strength inside buildings - but this is an exception, not the rule.
7. N8s GPS receiver is really fine, very sensitive. No problem with that.
In short: Go outside. Don't use AGPS or network-based GPS. Don't believe people saying "Precise (!) GPS fix is much faster with software blabla..." Don't get fooled by a quick display of an estimated position: The real position fix did not get calculated at that point of time; it's still running in the background. This is what's causing that constant change of your position right after the first fix got displayed. A minute later, your position appears stable; and that's the point of time where real positioning data are used - not just coarse estimations.
It all depends on that almanach data and a clear view of the sky.

Similar Messages

  • How can I find the position of a robotic arm with a cFP-CTR card?

    Hello,
    I use a CTR-500 to measure the pulses of 3 encoders.
    The encoders are related to the 3 axis (x,y,z), to which a robotic arm is moving.
    Each encoder has 2 channels (A,B) which go to each pair of Count Inputs of the CTR card.
    When the robotic arm is moving on one axis, the corresponding pair of Count Inputs is increasing, but there is a phase between the one Count Input and the second one. What is more, the Count Inputs do not decrease when the robotic arm is moving to the other direction, but they still increase.
    So, I cannot find easily the position of the robotic arm.
    What I have done, is to try finding the position, by using only one Counter Input for each axis. This means that I use the value of the encoder as a counter, and I calculate the position with some software tricks. But for some reason, it does not work properly.
    I have heard that the method I use is not proper. Instead, I have been told that I must use the phase of the 2 Count Inputs, in order to find the direction to which the robotic arm is moving. But, the Count Inputs of the CTR are augmenting in parallel, when the robotic arm is moving forward or backward.
    How can I find the position of the robotic arm, as it is moving like a CNC ?
    Thank you very much.
    Message Edited by nikosfs on 08-21-2009 12:27 PM

    You don't want to use a cFP-CTR-500 card.  What you have are quadrature signals.  You should be using the cFP-QUAD-510.  It has 4 channels that can handle both the A and B signals of a quadrature encoder.  It has the built in circuitry do determine the phasing of A vs. B to know when to count up vs. count down.

  • With the Position Number can we find other positions in the Org Unit

    Hi,
    With a particular position number can we find other postion in the same Org. Unit.
    The other postion is not a reporting postion of others.
    I repeat if I give a postion number which is not a reprting manager position but still I would Like to find the other position in the Org. Unit.
    Or which Evaluation path is used for it.
    Thanx in Advance.
    Regards,
    IFF

    Hi,
    In the present scenario I just know only the postion of the employee,
    I just want to know the  evaluation path wrt position by which I can find all the positions associated with the same org unit  wrt to the known position.
    I just want to pass Otype  as S positon  in the FM RH_STRUCT_GET , and get the all positions associated with Org. unit wrt to known position.Please let me know the evaluation path.
    Regards,
    IFF

  • My iphone is lost .is iphone 4S.How can I find it.Positioning is not open .

    Positioning is not open.Can not find do it

    Thank you..they told me
    "hank you very much for your inquiry. I am Kawasaki. I would be grateful if you kindly let me explain your inquiry.
    I am terribly sorry for the inconvenience.
    Yet, to our regret, no au-smartphone can be used without having our cell-phone contract as of now.
    Moreover, we are afraid that any au iPhone is locked when you insert any SIM card of another company brand in it; in other words, every single au iPhone has the carrier lock on it, and there is no way to unlock au iPhone at this moment for any reasons whatsoever.
    I am sorry for being unable to be of assistance to you right now."
    can i use this site to unlock my iphone https://www.officialiphoneunlock.co.uk/

  • My n8 gps positioning can't find me off-line abroa...

    I just got back from Spain i had the maps for Spain downloaded for off-line use but for some reason in off-line mode the gps couldn't find me unless I went on-line and that can be expensive anyone know why? any help is appreciated

    Yes you can do that. However dont expect the fix to not disappear, especially if its only relying on A-GPS at that moment because the I-GPS hasnt calculated yet. It will however make locking on using Integrated much faster since the app already knows your general location via the A-GPS data you have used.
    Offline mode can be used completely like online (except for searches), only trouble is that it takes time to get a fix simply because the antenna quality is not on par with dedicated GPS devices.
    If you find my post helpful please click the green star on the left under the avatar. Thanks.

  • How can I find the actual GPS coordinates of a photo?

    IPhoto 11:  for purposes of cross-referencing photos with physical samples (rocks, plants...) I want to be able to display (or otherwise discover) the actual GPS coordinates that iPhoto has imported with my still photos from Sony HDR-CX520V high definition video camera (GPS enabled).  Can I find the coords within iPhoto?

    I don't believe you can. I'm pretty sure that Graphic Coverter  can do this.

  • I can't find anything about how to properly manage the tablet's layout in horizontal or in vertical position.

    I can't find anything about how to properly manage the tablet's layout in horizontal or in vertical position.
    If I consult my website in vertical position, it's ok but, If I turn my tablet, all the hyperlinks and all general visualization are wrong.
    How I can properly handle both views?
    PS: I'm sorry for my bad english

    Could you share the site URL so we may check at our end? Also could you share some screenshots explaining the 'wrong hyperlinks and visualization'.
    Thanks,
    Vikas

  • Where can I find the GPS coordinates in iPhoto 11 for geotagged pics? In iPhoto 09 this information was available under the Photos menu "Show Extended Photo Information".

    Where can I find the GPS coordinates in iPhoto 11 for geotagged pics? In iPhoto 09 this information was available under the Photos menu "Show Extended Photo Information".

    I think you can only see the map.  To see the actual EXIF data you would need to export and use a viewer.

  • HELP! how can i find my lost 8530 using GPS?

    not sure if it was stolen, or just not returned yet but it seems to be turned off. Any way to find it??

    Hello Elka!
    Welcome to the Community
    We're sorry for what happened to your phone. I don't think GPS can help you find the phone because if you called your carrier to report it lost or stolen, it must have been suspended already. IF it's not been suspended, it must have been turned OFF by the founder.
    Blackberry Curve 8530 only has A-GPS, it means Assisted GPS so it may only be assisted by the Carrier Network find its nearest Cell Tower. If the phone is suspended or turned OFF, it will not work because it needs a Mobile Network to connect to. And if there's an app such as Blackberry Protect intalled on the phone, it may help you find the location but not the exact location as it only has A-GPS functionality. And for further details about Cell Tower's coverage. Rural Cell Towers have a larger radius compared to an Urban Cell Towers so if it was brought to a Rural area, using A-GPS might give you a place miles away from the exact location of the phone.
    Hope the information above has helped in a way.
    Ron
    Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up Blackberry Battery Saving Tips | Follow me on Twitter

  • Can't find my phone - can i locate it using the GPS?

    Yep, I can't find my iphone. Is there a way I can locate it given its GPS capability? Any help, whatsoever, would be greatly appreciated.
    Thank you!

    Do you have any idea where it is? If its on, the phone company can figure out where it is, roughly. I'm not sure how one would go about asking the company to tell you this information though. I assume it wouldn't be easy to get this information. At least I hope it wouldn't be easy.
    Think of all those cop shows where the cops track people by their cell phones.

  • TS3376 Can I find out where my iphone was located from? I think my account was hacked and my position was located..

    Got an alert on my phone that said "find my iphone alert" and it started beeping. I changed my password and I think Im ok now, but can I find out where I was located from?

    BrandinGNJ wrote:
    Yea your right, and thank you. A way to see where it came from would be a useful feature..
    But that might allow a thief (who may now have seen your diary) to locate your place of residence.

  • How can I find my stolen phone by using gps?

    My iphone has been stolen.  I have the find my iphone app and am trying to get someone who can help me locate it so that I can also find my purse with my ID and other important documents and meds.  I have reported it to the police.  Can someone tell me what I need to do? 

    MobileMe: Set up Find My iPhone
    MobileMe: Find My iPhone overview
    iPhone User Guide (For iOS 4.2 and 4.3 Software)

  • Cannot find the ''Positioning Methods'' option on ...

    Hello....I have recently bought the C7-00 and I wanted to test my GPS but I could not find the "Positioning Methods'' option to select the A-GPS, so can anyone help on this.
    Thank you.

    Do you not have a Location app in your Applications Folder ? As CJ mentioned , that is where you set your location methods to on/off. Inside Location you should have 3 sub folders, Landmarks,GPS data and Positioning. Open Positioning and you should be able to change the settings !
    If I have helped at all, a click on the White Star is always appreciated :
    you can also help others by marking 'accept as solution' 

  • 808 can not find my location

    When I start maps app it can not find find my location The red circle in the top left corner blinks and nothing happens
    Applications which must use my location do not work too
    The Internet works.
    May be I shall change any settings?

    @alexMoscow
    It should only be obtaining the very first postional fix that might take time, although if inside building WiFi/Network GPS positioning method should very quickly grab position from previously determined router access point location.
    Happy to have helped forum with a Support Ratio = 42.5

  • Time Capsule can't find AirPort

    Hi there,
    I have just got an airport to back up my Mac OS 10.6.8 and have successfully connected it to the WiFi, and it is seen through ststem preferences but I want to use it as a back up tool too and when I go through Time Machine it can't find the device - any help would be great!

    It's A1470, air port time capsule 802.11 ac.
    Bit worried that it's not safe or time machine as that is the exact reason I bought it and was recommended it in the apple store?!
    That is fine.. it is just you posted airport, not Time Capsule.. and what most people mean by airport is the extreme.
    Next problem..
    The TC must not be properly setup. Indeed it is not possible to setup an AC model TC or AE using 10.6.8 OS so please tell us how you set it up.
    I have just got an airport to back up my Mac OS 10.6.8 and have successfully connected it to the WiFi
    How?? The 5.6 utility in SL cannot do it.
    Are you using an iphone/ipad with the latest airport utility.
    Once setup the older OS should be able to use it.. but it cannot do the setup.
    Let me suggest you give us more details.
    A few screenshots helps no end.
    What are you seeing in the finder and airport utility?
    Does the TC show up in Finder?
    You said you can see it in system preferences.. sorry but I am not sure how.. please screenshot that as well.
    As a setup method.. if you really have joined the TC to the existing wifi (unless it is an apple router) that is the worst possible seutp.
    Please plug the TC WAN port into the main router LAN port by ethernet.
    Reset the TC to factory and redo the setup.
    Universal Factory Reset.. any model TC or AE.
    Unplug your TC/AE from power or turn off at the power point.
    Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
    Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
    Note..
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
    No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.

Maybe you are looking for

  • Mail app crash

    My mail app crashes every time I open it. I can access mail through iCloud via a browser! I am running OS X Yosemite but I am sure it is not related to this update as the problem has been ongoing before this. Any ideas please? thank you jinxysculler

  • DVD's read as blank even though they have been written.

    The problem is the following: DVD's that I burned using both Tiger and Leopard 10.5 (before 10.5.1) are not being recognized as blank. These discs are NOT blank and they display their contents in other Macs and PC's. When they are inserted in my driv

  • Why do "official" NXT blocks have to be password protected?

    Like everyone, I'm new to building NXT blocks with LabVIEW.  The projects we had in mind when we got LabVIEW were to combine and modify existing NXT-G blocks to make them more suitable for our purposes.  However, the first thing I learned was that th

  • Protection Agent failure error during backup to tape with DPM 2010.

    DPM TechNet Forum, We are experiencing an intermittent error when backing up to tape using DPM 2010 (with latest QFE roll-up applied). "The operation failed because of a protection agent failure. (ID 998 Details: The device is not connected (0x800704

  • Stupid transition bug... black square appears

    Hello I am not very experienced with flash at all... but I wanted to make a nice slide show swf file to go on a CD of images I am creating for someone. I figured out how to put them all in layers, do motion tweening on each after they'd been converte