N8 no longer recognised by my mac, it was, but no ...

The Nokia device “N8-00” is currently connected in a USB mode not supported by Nokia Multimedia Transfer or iSync.---- where do we go to change the mode on the phone..? or is it changed on the mac..? I've installed multi media transfer but to no avail..?

@nico01
Default USB connectivity mode upon N8 is Nokia Ovi Suite found in Menu > Settings > Connectivity > USB which should be recognised by Nokia Multimedia Transfer.
Have you updated your version of OSX Lion by any chance?
Happy to have helped forum with a Support Ratio = 42.5

Similar Messages

My ipad has upgraded to IO6, but is now no longer recognised on my mac (10.5.8) or my itunes (10.6.1). What can I do? Can I revert ipad back?

My ipad has upgraded to IO6, but is now no longer recognised on my mac (10.5.8) or my itunes (10.6.1). What can I do? Can I revert ipad back?

You can't downgrade the iOS on the iPad.
Quit iTunes, reboot the Mac and reboot the iPad and then try again.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

My Mac notebook does no longer recognise my external keyboard which was connected by a USB cable. I have checked the keyboard on other Mac notebooks and it works fine. Any suggestions?

My Mac notebook does no longer recognise my external keyboard which was connected by a USB cable. I have checked the keyboard on other Mac notebooks and it works fine. Any suggestions?

and in some kind of record, I've read another thread an it's fixed!!
Kids.
Accessability-> zoom-> off
5 days i've been squinting!

IPAD1 is no longer recognised by my MAc. Itunes freezes when I restart everything. My iphone 4 works fine. How do i fix this?

My IPAD1 is no longer recognised by Itunes on my Mac deskop. I have follewed the steps recommended by Apple Support aand sometimes after shutting everything down & restarting Itunes briefly recognises my ipad before freezing. Thereafter it sometimes recognises an Ipad is connected but says it cannot identify it. THe message readds "An iPad has been detected, but it could not be identified properly. Please disconnect and reconnect the iPad, then try again." Dsiconneceting & reconnecting achives nothing. However the Ipad does receive a charge from the Mac
This started after updating some Apps, and the next sync advised me that there had been issues syncing Apps. Then this problem started.
How an I reconnect my IPAD so Itunes recognisese it?. THere is no problem syncing my Iphone4s

- Look at the dock connector on the iPad. Look for abnormalities like bent or corroded contacts, foreign material and cracked or broken plastic.
- Reset the iPad. Nothing is lost
Reset iPad: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Make an appointment at the Genius Bar of an Apple store.

Burnt DVDs no longer recognised on my mac

Recently, my internal drive is acting up. It no longer recognises burnt DVDS. they don't show on the screen and then they just self eject.
Also, when I insert a burnt CD, it is not always recognised on the desktop.
I'm using 10.7.5. Any suggestions?

Hi imnokid2,
Welcome to the Support Communities! The resource below will explain how to check your optical drive if it is not recognizing your DVDs. Does it have any problem reading/playing store-bought DVDs? What software are you using to create the DVDs?
Get help with the slot-loading SuperDrive on your Mac computer - Apple Support
http://support.apple.com/en-gb/HT201788
Accepts discs but they don't mount or are automatically ejected
Reset the System Management Controller (SMC).
Ensure your drive can read the specific type of disc being used. The System Profiler or System Information may provide additional information regarding what media your computer supports.OS X Lion v10.7 and later: Click the Apple () menu and then hold down the Option key. Choose System Information from the menu.
If the disc continues to not be recognized, contact Apple or an Apple Authorized Service Provider, or make an appointment with an Apple Retail Store.
I hope this information helps ....
- Judy

Bluetooth module no longer recognised in Mac Pro

My Mac Pro's been doing some strange things recently.
A couple of days ago I noticed things were running very slowly, just moving windows about they would jerk and jitter.
Tried hardware test, disk utility etc but no problems found. I then unplugged the machine and plugged it back in - problem solved.
Now today I started up the machine, go to login to my account and my keyboard and mouse don't work. They become initialised if I unplug and plug them back in, or if I wait about a minute they start working.
Along with this, my bluetooth module is no longer recognised under Mac OS X, although when I reboot my machine into Vista the module is recognised and functions correctly.
It also takes over minute to shut the machine down, which it has never done before. When turning it off the OS seems to quit quickly, but the screen remains black for a long time before the power is cut the the drive etc. (This is especially noticeable when restarting the machine as it takes more than twice what it has done in the past).
Is this all just coincidence that these things happened at the same time, or are they related?

Have you tried the standard debugging steps listed in the troubleshooting guides here and elsewhere?
You might try looking at http://www.thexlab.com and other websites like that for information about how to debug various problems.
If you are OK with opening your case, you can also reset the SMC controller on your motherboard, which can affect at least some of the subsystems you are having trouble with.
But first, you need to do more general diagnostics.
Run your MacOS hardware diagnostics by putting your OS boot CD in your optical drive, and hold the D key down when you boot.
You can also hold down C when booting and when the installer appears, go to the menu and run Disk Utility, and verify at least your primary drive.

I have downloaded ios8 and my phone has frozen on Apple screen. The MAC no longer recognises this device. Please help!

I have downloaded iOS8 onto my iPhone 4S - the phone has frozen on the Apple screen (and it keeps going black). It is also no longer recognised as a device on my MAC...please help

Make sure airplane mode is off and wifi is on. If no go try restoring in itunes and if that fails you will most likely need to call apple or go to an apple store to get a repair

External disk no longer recognised on Time Capsule

I have a 500GB Time Capsule connected to my broadband router by an ethernet cable. My Mac Pro is connected to the TC by ethernet and WiFi and I also have a MacBook which uses WiFi to connect to the TC. I have a USB hub connected to the TC with a Canon printer and Iomega external disk attached.
This all worked fine until a week ago when I updated the TC firmware from 7.4.2 to 7.5.2. I had problems with WiFi not working so went back to 7.4.2. I then updated the Airport Utility to 5.5.2 and tried the 7.5.2 firmware on the TC and now the WiFi works with no problem.
But - the external Iomega disk is no longer recognised. I cannot see it via the Airport Utility and it doesn't show up under Shared using Finder.
I have connected the disk directly to my Mac Pro and it shows up and Disk utility gives it a clean bill of health. I've tried connecting the disk directly to the TC (not going through the USB hub). Still no go.
I've tried rebooting the Mac Pro, turning off the TC - nothing seems to work.
Anyone have any thoughts on why this is not working?

I have a fix for this problem but it entails restoring version 5.5.1 of Airport Utility, then returning to the 7.4.2 version of the TC firmware.
All working now! I guess I'll stay with the old utility and firmware until Apple fixes this.
Message was edited by: Geoff Roynon

My itunes no longer recognises my ipod nano and won't sync. Any advice?

My ipod nano is no longer recognised by itunes and won't sync. Itunes is on a Window 8 computer and while windows sees the device, itunes won't? Any advice?

Hi caro101,
Welcome to the Support Communities! The article below will help you troubleshoot the issue you are having with your iPod nano not being recognized in iTunes.
iPod: Appears in Windows but not in iTunes
http://support.apple.com/kb/TS1363?viewlocale=en_US
If you see your iPod in My Computer (Windows XP) or Computer (Windows Vista, Windows 7, or Windows 8) but not in iTunes under Devices, try these steps. Start at the top and work your way through the steps until iTunes recognizes your iPod.
If you don't see your iPod in My Computer, follow these steps.
This document is for Windows users and most older iPod models. See the following articles if you have this issue on:
A Mac
An iOS device (iPhone, iPad, or iPod touch)
An iPod nano (5th or 6th generation) (and you see an alert message in iTunes when you connect the device)
Cheers,
- Judy

No longer recognising DV files

I'm using Final Cut Pro 4.5 on Mac OS X 10.4.2. I've got a single Final Cut Pro project with around 12 hours of DV footage. All of the clips are stored on an external LaCie FW800 500GB drive, formatted in FAT32. I have another, identical drive, formatted in HFS+, which I use for my backup.
Recently, the FAT32 drive started having problems, so I checked the drive for errors (under Windows) and most things seemed to be fine. However, one of the 12 folders containing about 12GB of DV clips became scrambled and could no longer be read. All other 11 folders were fine.
No problem, I thought, I'll just copy over the backed up files from the HFS+ drive to the FAT32 drive and start editing again. However, when I did this, Final Cut Pro started up with the very helpful "General Error (34)" whenever I tried opening this project. I narrowed the problem down to the backed up clips that I had. Having looked on the FAT32 drive, all of the DV clips are now listed in the Finder as "UNIX Executable File", with the corresponding black icon. The files will no longer open in FCP or iMovie 5. Quicktime won't open them, complaining that it doesn't recognise the file format.
In addition, ALL the backed up versions of the clips show this problem! While the DV clips on the FAT32 drive for the other 11 folders show up correctly, and will open in any of the above programs, the backed-up versions on the HFS+ drive all show up as "UNIX Executable File" and will not open. This means my backup is currently completely useless!
Is there any way I can recover these files? The files themselves seem intact, and the backup versions were created almost as soon as I'd imported the original clips, so they should be fine. It's just that they're no longer recognised as DV clips, so I'm stuck.
Also, am I causing myself problems by using the FAT32 disk as my primary scratch disk, as well as containing all the DV files?
Finally, is there a way to back these files up so that the file type is retained? I'd like to think that the backed up versions were actually backups!
Simon.

Right, finally cracked it. Based on my limited knowledge of Mac file structures, I wondered if the problem was caused by using 'rsync' for my original backups. It appears that the problem arose because however I had backed up the files hadn't retained the type and creator codes for the DV clips in question. I downloaded the utility 'FileType', which allowed me to set the file and creator codes for the 'broken' DV clips, set them all to match the good files, and lo and behold my FCP project was working again!
I then copied all the DV clips over to my HFS+ backup disk by hand (very laborious) and started digging about for problems with the backup. It turns out that 'rsync' doesn't support Mac OS X type and creator codes (which also explained why I had a whole range of "._" files floating around - apparently these contain the file/creator codes), which meant that all this information was stripped off when I ran the backup. Hence FCP (and Quicktime) could no longer recognise my DV clips.
I shall now have to find another method of doing my backups. But for now: success!
Simon.

PC no longer recognises my iPad as a device

Since updating latest software, my PC no longer recognises my IPad . I get error message on my PC stating that my device has malfunctioned & I should replace my device ! Unable to sync. Any idea what I can try next ?

Hi there,
I would recommend taking a look at the troubleshooting steps found in the article below.
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/TS1591
-Griff W.

HP Envy 120 All in One Printer no longer recognises MacBook Air

Since upgrading to Yosemite, my HP Envy 120 no longer recognises my Macbook Air and vice versa via the router, having worked previously (not perfectly all the time admittedly but connection wasn't an issue). I can connect Macbook to printer via HP direct, but this means disconnecting from the internet, scanning, then re-connecting to internet which is a bit of a faff and seems a backwards move.
I have downloaded the latest HP printer driver software, followed all suggestions I can find on this such as deleting the printer on the Macbook under system preferences, but when I try to add it back on, nothing shows. I've tried adding the IP address manually, this comes up with an error message. I've done the wireless wizard on the printer and that was successful so it is connected to the router but is not detecting my computer, which is also connected to the same router.
The printer is still under warranty - I meant to take it back when I had earlier problems but decided to stick with it a bit longer. I'm just trying to work out - is it a HP problem or is it an Apple problem - ie can I return the printer under the warranty?
Or does anyone have any simple fixes? I'm not at all computer literate!
Many thanks!
This question was solved.
View Solution.

Hi,
As you mention that you do able to use the printer with no issues by using HP Wireless Direct, that means that this is neither HP or Apple issue but a network connectivity issue.
Apple devices uses Bonjour to communicate with the printer, that relies on IP Muticasting which need to be supported by your router.
If I clearly understood your description and the device do work as expected using HP Wireless Direct, the router is the cause for this issue as you do not see similar issues while removing the oruter from that acquisition... please also let me know if i have misunderstood your intention about the issue.
Additionally, have you tried rebooting your router by unplugging its power for 10-20 seconds? once it starts up reboot both the printer and then Mac and check for any difference..
Please try that and check if that help. if the issue persists do let me know your router brand and model, its settings or capabilities may cause a such and may prevet this kind of connectivity.
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Computer no longer recognises ipod?

i have a black 8G nano, its about 2 weeks old, no idea what generation it is.
anyway the computer no longer recognises it, either my pc at work or my macbook at home. it charges but it doesnt show up as a drive, and when i open itunes it doesnt appear in the list so cant even reset it!
help!
thanks in advance.

Hi TrakStarr,
Just saw another post like yours but the problem was with a 5th Gen.
Here's the "All-in-one-fixer-upper" I just found while trying to fix a similar problem with my 5th Gen.
Remember, this link offers FIVE suggestions to get ALL iPods running again. I've booked marked this page. Here's the "fixer-upper" link.
http://www.apple.com/support/ipod/five_rs/
Hope that helps.
iMac 20" Mac OS X (10.4.9) iPod 5th Gen 60GB-Mac

Ibook g4 no longer recognises iomega external hard drive

I bought a iomega hard drive to use for itunes library and ibook was full up, transfered library over and this week as i was setting up a new play list itunes crashed and the ibook is no longer recognising the iomega. It's extremley annoying and i don't know how to solve it - any ideas would be gratefully appreciated.
ibook G4 Mac OS X (10.4.9) iomega - LPHD120-C

Welcome to Apple Discussions!
See my FAQ*:
http://www.macmaps.com/firewirebug2.html
* Links to my pages may give me compensation.

My CS4 PS no longer recognised the iPhoto library since a new video card was installes a few days ago. How do i fix this? I can drag and drop but then I can't use camera raw feature.Tks

My CS4 PS no longer recognised the iPhoto library since a new video card was installes a few days ago. How do i fix this? I can drag and drop but then I can't use camera raw feature.Tks

When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.

N8 no longer recognised by my mac, it was, but no ...

Similar Messages

Maybe you are looking for