N80 access points

i checked that there were no access points defined. when i went to "net" it asked me to choose connection it came up with vodafone internet gateway. I dont know why its like that? i went to settings and there was no access points there at all.
next thing i did was use nokia settings wizard to get my vodafone access points and it created "vodafone internet gateway(1)"
in settings->access points, there is only one copy of it there.
when i go to "net" it asks for which connection i should use and i see two copies there.
why is like this?
under settings there is only one copy but somehow the fone thinks there is 2 so it must have been setup or entered somewhere and i cant seem to find out where or what i should do about it
remember, this is from a fresh reformat of my fone.
anyone got any ideas of what i should do without having to format again? formatting again might work, but then again it might not.
maybe its stored on my sim card automatically and thats where it is?
i just dont know

Have you sent up email retrieval to automatically download, check the email settings?
Otherwise you might have setup some SIP settings. Do you have any profiles in Tools, Settings, Connection, SIP Settings? If so and you know you are not using them, then delete them.
Another one to check, although less likely is under Tools, Settings, Connection, Packet Data and check that is set to "When needed" and "None"
(PS always usful to post your SW version so we know where you are coming from....)

Similar Messages

  • Using n80 wlan on mixed mode n/g access point?

    I have a d-link dgl-4500. I use it in mixed mode n/g. My computers can connect just fine.
    If I want to get the n80 to connect, I have to first change the wireless channel to 11 and then change it to channel 1.
    Then and only then will my n80 find the access point.
    If I set my AP to G only, then the wlan fires right up.
    I'm not an expert on wifi. Are there any advanced wifi settings I can change to help my n80 find the AP easier?
    current settings:
    2.4GHz mode
    mixed n/g mode
    2.412 CH. 1
    auto transmission rate
    20MHz channel width
    visible SSID
    beacon 100
    RTS threshold 2346
    fragmentation threshold 2346
    DTIM 1
    short GI yes
    802.11b protection no
    Those are my current settings.
    Thanks for anyone who can help.

    I have a d-link dgl-4500. I use it in mixed mode n/g. My computers can connect just fine.
    If I want to get the n80 to connect, I have to first change the wireless channel to 11 and then change it to channel 1.
    Then and only then will my n80 find the access point.
    If I set my AP to G only, then the wlan fires right up.
    I'm not an expert on wifi. Are there any advanced wifi settings I can change to help my n80 find the AP easier?
    current settings:
    2.4GHz mode
    mixed n/g mode
    2.412 CH. 1
    auto transmission rate
    20MHz channel width
    visible SSID
    beacon 100
    RTS threshold 2346
    fragmentation threshold 2346
    DTIM 1
    short GI yes
    802.11b protection no
    Those are my current settings.
    Thanks for anyone who can help.

  • N80 email access point wandering

    Hiya
    I've set up email and wlan fine - and the standard Orange settings for GPRS are working with no problems.
    My issue is when I start wandering around!
    I set up the phone to check for email though my wifi connection on a regular basis. The idea is that I'm sitting around in the evening without a PC on and my phone will alert me of new email. This also works fine.
    However when I leave my hotspot, I want the phone to think "err ok I can't get that connection, I won't keep checking email". I thought that "only in home net." would probably do this in "Automatic retrieval". This appears to work ok as the "Access point in use" for "Incoming email" is et to my wlan..
    But, when I go out and about and manually try and check my email, the phone says "Can't find [wlan]" and gives up with no option to check the GPRS connection.
    Err - any ideas? I don't think I'm trying to do anything out of the ordinary. I just wwant regular email checks when I'm within range of my lan, and this to stop (unless I manually override) when my only option is internet access that I have to pay for.
    I don't see tinkering with the settings on 3 email accounts whenever I come in / go out to be an option.
    Any ideas?
    Thanks in advance,
    Neil
    www.babylondirect.com

    Menu > Tools > Settings Wizard.
    If this doesn't work, back up everything and type *#7370# to soft reset or take it to your nearest Nokia Service Centre and get software version 4.
    Nokia N80 - v4.0623.0.41

  • How can I monitor the active access point + data c...

    My privider (o2 Germany) requires me to use different access points (APN, proxy) on my phone (N80) depending on the type of browsing I want do do (WAP vs. "normal" access), and each of them has a "high cost trap" if I use the wrong one for the particular service.
    Very annoying - up to the point that I consider not using the phone for online access at all because I'm so scared to run into uncontrollably high fees.
    Anyways. I wonder if there is add-on software for my phone that helps me monitor my data connection, i.e.:
    * show me the currently used access point at the top of the display (yes, I know I can go into some deep menus to look it up, but that's not very helpful or even easy to use)
    * automatically disconnect when the conn is idle for a while (One of the data modes is time-based, meaning I do not want to have it open all the time by accident)
    Currently, all I can see at the top of the display is that I have a data connection at all, but that does not give me enough information to know I'm in the right mode for what I'm doing.
    Thomas

    You can force a disconnect by pressing the red/hangup key for a couple of seconds when the phone is in the standby state.
    And in menu > Tools > Settings > Connection > Packet data change the setting "Packet data conn." to "When needed" and leave the "Access point" setting there to "None".
    When you or apps on your phone are not doing any data transfer, then regardless of whether it is a WAP or "full" Internet packet data connection, you should not cumulate any charges.
    You can also move the Connection Manager app from the Tools submenu to the main menu, or even to the Active standby apps list (or the softkeys) for quicker access. No need to deep dive into menus for it then.
    And for individual apps, you can usually set the default access point to whatever is best to use for that particular app. For the browsers ("Web" and "Services") you can also make them ask you to pick the access point every time you connect.

  • Can N80 access MS Exchance email/calendar thru WLA...

    Can I access office email using Nokia N80 and WLAN? I don't want to go thru GPRS or other data services thru mobile provider. I tried defining an access point and then use it for mailbox, doesn't work.
    Also can it sync with calendar using WLAN?
    email/calendar server I am trying to access is MS Exchange.
    Thanks
    A

    Nokia mail for exchange or dataviz roadsync can do sync with Exchange.
    See here:
    http://www.businesssoftware.nokia.com/mail_for_exchange.php
    and here:
    www.dataviz.com/roadsync
    They can use either the GPRS or WLAN settings. Not sure why your email does not work but it is probably a configuration issue with the WLAN or email settings. Check if you can browse the web with the WLAN settings.

  • Unable to stop the event logs on access point console

    Hi team,
    I have an AIR-LAP1131AG-E-K9 access point having ios c1130-k9w8-mx.124-21a.JHB1.
    When I am trying to take the console of it there are many logs generated like LWAPP ...Go join the controller, Discover controller etc. and the ap is unable to register to the controller(2112 with ios version 6.0.199.4). I'm trying to enter the command but there are many event msg generated....How do i stop this event log. I tried entering the command no debug all. but still there are many logs...
    I want to enter the the following commands
    #lwapp ap  ip address <ip addr>.
    #lwapp a pip default-gateway <gateway ip addr>
    #lwapp ap controller ip addr <controller ip>
    #wr me
    Revert me back on urgent basis
    Thanks in advance..

    Thanks Rashika,
    Now the access point got registered to the controller..This happened becuse of country Code..
    I have changed the country code to UK, Belgium it started working fine.
    Initially when it was IN the access point was not getting register..
    But now the problem which arised is that the user is unable to get authenticated to the radius server.
    Radius server is reachable and we have done every changes required for radius server authentication.
    Users are getting rejected.
    Customer is saying that the radius server is in IN domain and the WLC/access point is in UK,BE and hence the users are unable to connect..
    Is it so??
    Rply
    Thanks in advance...

  • How do I make my AirPort Extreme a access point?

    I just bought a Time Capsule and now I want to extend my range of my network.  How do I make my AE an access point?

    In this case, you will want to configure both base stations in an extended network.
    Dynamic WDS - Extending a Wireless Network Setup
    If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
    Open AirPort Utility, and then, select the base station that will connect to the Internet.
    Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
    Click AirPort in the toolbar, and then, click Wireless.
    Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
    Next, select the base station that will extend this network, and then, choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
    Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
    Enter the base station network and base station password if necessary.
    Click Update to update the base station with new network settings.
    (ref: Pages 43-44 of Apple AirPort Networks.)

  • How do I configure my AirPort Extreme as a wireless access point?  My cable modem goes to a router, and one of those ports goes to my AirPortExtreme.

    I am about to hook up my airport extreme.  My cable modem goes into a router, and one of those ports will supply my airport extreme.  I was told by the Apple Store that I would need to configure my airport extreme as a wirreless access point.  How do I do this?

    With sbcgobal I got a Gateway 2wire modem. What I would like to know is how do I set up my APE as remote?
    Unfortunately, you won't be able to do this as few non-AirPort routers will work with AirPorts in a Wireless Distribution System (WDS).

  • Can't HP Officejet pro 8100 do wifi access point?

    Yesterday my HP Officejet pro 8100 arrived and I try to connect via wifi. I thinked that It need a infrastructure access point to print via wifi.
    When I powered on the printer I osserved that It create an access point autonomously with SSID: HP-Setup-7A-Officejet Pro, with IPv4 address server, etc...
    I was very happy and I printed a page with my smartphone samsung s4 connected directly with printer access point (not wifi direct but standard wifi).
    Today no changed occurred but I can't use printer with its own access point, but only with an external wifi access point.
    Someone can help me, please? It could be an hardware problem?
    Thanks,
    Luca
    P.S. in web server I checked that "access point connectivity" (Punto di accesso wireless connettività in Italian) is checked.
    This question was solved.
    View Solution.

    Hello lucait
    To print via WiFi you need to have a wireless router setup. Once you have the wireless router setup correctly you will have a SSID and Wepkey that will enable you to add devices to your network. The network will allow all your devices to communicate not just with each other but with the internet. At the moment your printer was not put in a network so instead of broadcasting on a network it is broadcasting on it's own network called HP-Setup-7A-Officejet Pro which is only good for a short period of time to allow you to setup your wireless. I am going to assume you have a wireless network and you are just needing assistance getting the printer setup on that network.
    To set your printer up on a network you will need to reset your network defaults so your printer begins to broadcast that HP-Setup-7A-Officejet Pro network again. You can do this buy following the steps on the HP Support document Resetting the Network Settings. Once you have done this you can begin to install the software that came with your printer on your computer. You want to set the printer up wirelessly when the option arrives. The software should configure your printers wireless for you and put it on the network. Once completed you should be able to access your printer from all your devices as long as they are on the network. 
    I hope this helps resolve your wireless issue. Thank you for posting on the HP Forums. Have a great day! 
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • Setting up a netgear n300 as wireless bridge/access point with airport extremee

    I just replaced my netgear wireless router with the airport to allow our many devices on the network without knocking each other off and also increase the speed.  But would like to use the netgear as a wireless bridge or access point so that I can still connect my NTFS formatted hard drive to be shared on the network.  Any suggestions would be appreciated.  I can not seem to find my netgear router with 192.168.1.1 as that comes up with another device.  I have tried doing this with a windows laptop in another room but can not seem to make it work.  I am now hooked up directly to the airport thinking i need to do it that way and still no luck. Please help.

    As long as you intend to do this over ethernet it will work.. you cannot easily wireless repeat or bridge to an apple router.. you would need specific hardware to do it.
    What is the exact model of netgear you have?
    The setup method depends on the functionality of the router.. but lets assume it does not have a bridge or WAP mode.
    You use WAN bypass.
    1. Setup the Netgear with IP address in the correct IP range for the rest of the network.. it is hard to talk generalities so lets say the apple is main router and your network is now 10.0.1.x .. then set the Netgear to 10.0.1.250 (apple uses IP 2-200 by default) you can use any value you like outside the DHCP range. Up to the limit which is 254 as long as you keep track of all static IP devices. Apply this setting and power cycle the router.. and you might need to power cycle the computer as well to pick up the new IP.
    2. Turn off the DHCP server in the Netgear. You may lose connection to the netgear now.. do not worry about it.. (this can be combined with one.. if you firstly turn off dhcp before you change the IP.. but whatever is possible.. at some point you will need to change around and if you forget what IP .. you will be in a mess.. so write it on a label and stick on the base of the router.. also without dhcp you will either need to reset router to factory using reset button or use static ip on the computer. )
    3. Plug ethernet from LAN of the main router to LAN of the Netgear. Reboot the whole network is often necessary.
    4. In your computer plugged somewhere in the network.. open browser and go to the address you set.. 10.0.1.250 in my example.
    5. You can then setup the Netgear to do whatever you like.. DIsk access is fine.. wireless is fine.. it just cannot be a router.
    Many many reboots if you get lost. Hit reset and start over.

  • New wireless network with several access points

    Hi,
    We are planing to deploy a wireless network that will cover two floors consisting of about 5 or 6 Access points. It should have 2 or 3 SSID (placing the clients in 2 or 3 different VLANS).
    What would be the best solution for this?
    I read a lot about wireless controllers. What about an option to just buy standalone access points? Are they all configured to work with the same SSID's and on the same channel?

    A centralized controller should make your life easier:
    - Centralized config - set up everything on the controller and it gets applied to the AP's.
    - Centralized monitoring - when someone has a problem, you can check the controller instead of having to figure out the AP to which they are connecting (computers don't always connect to the closest AP)
    - Dumb AP's - if someone steals one of your APs, they will not be able to learn much about your network from a lightweight AP
    - Radio Resource Management - let the controller make the channel and power setting decisions for you
    - If you use PoE, you may never have to get on a ladder and use the console port of a lightweight AP. The AP is managed by the controller, and for the rare occasion that you can't get an AP to respond - just cycle the power to the AP via the switch port.
    There are some downsides:
    - Cost of the controller (since you're buying AP's one way or the other)
    - Most cost: If your wireless network is important, then you typically want a second wireless controller as a backup
    - Probably more downsides, but my brain hurts today

  • When using EA6400 as an access point only, certain features lost

    I've set up my EA6400 and have it connected to my Verizon MW424WR(Gigabit) and it works fine as an access point and the Twonky Server uses the USB drive I have attached to the router's USB port. Problems:
    1)I can not use the linksyssmartwifi link for management, I have to use the IP(set for 192.168.1.50) for this. When trying to register/login, the Linksys end is trying to find a Linksys router but can not and will not allow any action.
    2)Although Twonky will use the attached HD, I can not share the device over the home (Windows) network. I've tried various incantations of the IP \\192.168.1.50\(whatever share name I can think of) with no avail.
    3)Using the Linksys admin, the Device List is incomplete. Devices connected wirelessly  such as my iPod, Roku, Sony Media Player and WD HD TV Live do not show as wirelessly connected and do not have an IP listed.
    4)Is there any point in using the Media Prioritization settings since no routing is done by an access point. Or will it actually prioritize the wireless connection.
    BTW, the Verizon router can not be set in bridge mode so I have to use the router as an access point to accomplish what I wish.
    TIA,
    Randy

    Some applications and router features require the use of the WAN port. If the router is set up for LAN to LAN AP mode only, then those features won't work in this mode. Only Router mode. 
    If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Then connect the router in router mode using the WAN port to the ISP modem, then features and apps should work.
    tduong44 wrote:
    I am having the same problem, not being able to use ANY apps like USB drive, FTP, etc when setting the device in bridge mode because I want to access the drive outside of my network using port forwarding.  Contact Linksys/Cisco support and was told that I needed to setup the Verizon router in Bridge mode..   That was it, that was the solution... AND also to check with provider for instruction how to.. WTH kind of support is that>??

  • An Error Occurred while trying to join "my wireless access point"

    Hi,
    I've been using wireless access for a year and never had a problem connecting.
    But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
    I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
    I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
    I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
    Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
    Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
    I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
    I get the strange feeling that they planted some kind of bug/virus!!!
    I don’t know what else to do.
    Anyone knows that problem? What can I do?
    Any help is greatly appreciated!
    I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
    http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

    Hello Tesserax,
    I get the same error message again...
    I tried the 3 suggested steps again, but unfortunately it did not work.
    After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
    Even if the Computer was asleep for just a second!
    I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
    Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
    And it works fine…until the screensaver comes on or it sleeps again
    I have the Problem with my IMac and Mini but the IMac at least remembers my password…
    Any Ideas
    I’m connected through a Buffalo WZR2-G300N wireless router

  • How to use Home Hub 3 as a 2nd router(access point...

    Hi guys hope you can help; I am trying to add my Home Hub 3 as a 2nd router (ie an access point) to my home network and struggling.
    What am I trying to achieve.
    I have a fully functioning home network which is working great but the wireless range does not extend to the room above my garage, some distance away from the main house. I currently service it with an Ethernet link from my E4200 router, via the mains wiring, to link to a PS3 there. But I want to extend this to have a wireless network in the remote room so I can link multiple devices - rather than spend more money, deploying a 2nd router which I already have  is preferable.
    What have I got.
    I have a Linksys E4200 router (nice piece of kit) attached to my ADSL line via a Belkin N1 wireless modem-router set to  “modem only” mode (I was using a DSL modem until yesterday but that went AWOL and digging out the Belkin router I saw that it had a modem only function – and it/they worked first time )
    All of my gear in the house is attached wirelessly to the E4200 which is delivering circa 11.5mbps from a maximum of 12.5mbps for the line measured by BT onsite. So  all is  fine there.
    What have I done to try and use the HH3
    Linked an Ethernet cable between one of the Ethernet ports on the E4200 to a mains plug.
    Linked an Ethernet cable from a mains plug to one of the Ethernet ports on the HH3 router.
    Ie as the PS3 was linked.
    3.  Switched on the HH3 router: the power light is solid blue, the wireless light is solid blue, the broadband light is off
    4. Connected my laptop to the HH3 network and loading up a web page on IE9 displays a web page from bthomehub.home/etc etc with title BT Home Hub and a message “Can’t connect to Broadband”. It is the start of a self- diagnostic routine. Answering all the questions I eventually get a Home Hub Administrative Home Page displayed.
    Is there a quicker way of getting to this admin page??
    5.  I switched off DHCP
    I changed the IP address from 192.168.1.254 to 192.168.1.200 as this seems to be what the other threads on this subject did.
    When I went to apply the change a message came up telling me that I might not be able to access the HH3. I ploughed on disregarding this and needless to say I could not then access the HH3 via the web interface and trying to access a web site nothing happened.
    6.  I did a hardware reset on the HH3
    7. Going through the motions again, when I got to the admin pages again, I switched off DHCP and this time left the IP address alone, ie 192.168.1.254.
    When I went to apply this  I got the message
    “After changing these settings you will need to renew the IP address of all devices connecting to your BT Home Hub. Please follow the instructions provided with your devices.”
    I applied the change – but have not yet done any fooling around with IP addresses on my laptop because I don’t want to start mucking around with my laptop
    I then tried to access a website, and failed, but on this occasion rather than nothing happening, the Home Hub website came up  again displaying the error message page.
    And that is where I stand. All looks so easy when reading other threads on this and other forums but it is not working for me.
    Any help greatly appreciated.
    The IP settings on the E4200 are
    IP  192.168.1.1
    Range  192.168.1.100  to 192.168.1.149
    Also connection type on the E4200 is POE not POA – as far as I  recall that is what it needed to be to connect to the DSL modem and work.

    Thanks for the speedy reply!
    I have actually came across this page before - I seem to hit a snag when I connect the repeater hub (my HH3).  As outlined, I have at all times kept the repeater hub connected via ehternet into one of the regular LAN ports to my main HH5.
    But when I connect my laptop to the repeat hub (HH3), I am actually connected to the internet somehow (I assuem using the HH5 network) but under my network connections it says I am connected to the HH3.  As a result, when I go to the homehub settings page 192.168.1.254, it brings me to the main HH5 settings page and not the repeater HH3.
    According to the instructions it says I should "Ignore the not connected page", but I am connected and I cant seem to alter any of the settings on my HH3 while it is connected to the HH5.
    Any other pointers?
    Thanks!

  • What is the WPS button on my access point?  I am trying to setup wirelessly with a canon MX892 printer

    Printer setup instructions say to press the WPS  button on the access point (my 4th gen Time Capsule).  Does that mean hit reset and will I have to setup every other device again by doing that?

    No, do not hit reset .. it is not a WPS button.
    Apple products do not use WPS, so no WPS button is needed. And they have no need to implement one.. nothing exists outside the Apple bubble.. didn't you know that??
    Read the forum expert Tesserax instructions for using WPS. https://discussions.apple.com/message/16034147#16034147
    But it is better to plug in your printer to a mac by usb and use the disk provided to do a full manual setup of wireless.. WPS is simply the easy way.

Maybe you are looking for