N80 Firmware Upgrade Problems.

Hi I have just used the Software update utility to update my N80 from V3.x to the latest one v4.x. It now hangs when trying to open menus ie when trying to open the SMS menu or gallery. It has also locked up a few times after hanging up a call. Trying to take a picture worked but it took ages to open the camera application. Can anyone tell me if there is some way to fix this? Cheers

I got similar hanging problem when I had restored data after upgrading. There are some sis application which does not restore properly. A format will only help here otherwise you have to identify the sis in the memory card and delete it in data transfer mode.

Similar Messages

  • Nokia n80 firmware upgrade problems

    Hi all i just tried to do a firmware upgrade using the nokia sites stuff and my pc crashed and now my fone wont turn on could some1 please tell me
    1 if this is terminal
    2 if i can sort this out myself
    3 point me in the right direction for the info i need to sort out my 3 week fone
    4 how much i should expect to pay if i HAVE to go to a shop to get it sorted
    thanks in advance for any help given

    Right first thing I would try is to connect your mobile to your pc and try running NSU again. If it connects to your N80 great you should be able to just start over.
    (Tips: Run only the NSU on PC close all other programmes down. and ensure your N80 is charged fully or at least plug your charger into the N80 whilst doing the update.)
    If your N80 Isn't recognised by the NSU then its dead and the only way go revive the poor little things is to:
    1: Take is to a Nokia Service Centre. Carphone warehouse is usually your closest NSC, If your lucky they will have an 'on site' techinician and he will fix your N80 within an hour or same day, if not then you will have to leave it with them for a week or so.
    2: Call your Service provider, tell them your N80 just went bye bye and they should swap it for you or at least give you a refurbished N80.
    You won't be charged by the Nokia Service Centre for any work done as your within your warrenty and if you choose to go back to your service provider you should also be covered. This has happened to me and I sent my N80 back to O2 they had a refurbished model sent back to me within a couple of days with no charges.

  • Nokia n80 firmware upgrade problem

    hi, i have an nokia n80 and i-ve downloaded the pc software for upgrading the phones firmware and when remaining 53 seconds before finish phone went off and it doesnt decets my phone anymore...so i can not continue upgrading...the phone now doesnt event power on :X
    What should i do ?
    the phone has like 1 year since i baught it...if i go to nokia center i must pay to restore my phone ?
    Message Edited by jokerady on 28-Feb-2008 10:03 PM

    Sadly something has gone wrong with the update leaving the phone unusable. You can try a hard reset but remove the sim and memory card first.
    Hard reset:
    1. Switch off the phone.
    2. Hold down the following three buttons: Green (the call answer button), * button, and '3' button.
    3. While holding these buttons, press the power button and switch on the phone.
    4. Release when the phone shows the nokia logo or shows other signs of life like the language selction screen.
    If this fails the your only option is to get it repaired. If you are in Europe you get a 2 year warranty, not 1 year.

  • N80 Firmware Upgrade

    Hey, I have had an N80 for nearly a year now, and last night when I was attempting to back up my phone it seems to have gone a bit mad.
    Every now and again a Message flashes up saying
    MESSAGE: SUPPORT NOT FEATURED
    This is when going into Text messages or phone gallery, consequently I am unable to view the messages and the gallery as they will not load.
    I would be grateful if you had any ideas on what it could be and what I could do? Could it need a firmware upgrade?

    I think it's unlikely that a firmware problem like that would suddenly appear after a year.
    I would check the memory card first as it sounds like it could be problems there. Failing that, I would back up the phone and memory card and do a factory reset on the phone (see the pinned thread on the smartphone board for details of how to do this) and a reformat of the card.
    If you still have problems, then it's a trip to the service centre, I'm afraid.

  • N80 firmware upgrades (how?)

    Hello,
    There has been some discussion here about the N80 firmware. My N80 is orange and suffers from a few issues. Firstly the web browser is pretty much useless for me, out of memory errors on almost every page. Relatively frequent out of memory errors in Gallery whilst attempting to play a video taken with the camera. Snakes is not playable it crashes out as soon as you actually try to start the game.
    I'm wondering how firmware upgrades are peformed with a network like orange? I presume Nokia service centres wouldn't do this because of the altered firmware for the network.
    I'm in the UK if it makes a difference.
    Thanks,
    Richard

    Yep, but it's a pain to do as you have to keep backing up on the PC every time you get a new contact.
    Is that an N95 in your pocket or are you just pleased to see me?!?
    Life's too important to take seriously.
    Nokias I've owned 3210, 3310, 6100, 7650, 6600, 6680, 6630, N80, N95
    I'm a 26 year old boy BTW

  • **SPA2102 FIRMWARE UPGRADE PROBLEM WITH 5.2.12

    I'm having problems loading firmware 5.2.12 onto my SP2102-R ATA.  I have my laptop PC running Windows 7 directly with an ethernet cable from my laptop to the ethernet connection on the back of the SPA2102.  I run the .bin file and In order to get the software to the upgrade stage I have to enter ****, 73738 1# to move to the next stage.  I have now been waiting for 1/2 hour waiting for firmware download request from SPA.  IT DOESN'T GET PASS THIS STAGE.......CAN SOMEONE PLEASE TELL WHAT I'M DOING WRONG OR WHAT I NEED TO DO DIFFERENT?
    Thanks......

    Based on my experience with the SPA2102-NA, it is not necessary to do a factory reset (*73738) in order to perform a firmware upgrade/downgrade.
    However, now that you have done so, any and all previous user settings will have been reset to the original factory settings (including user set passwords - assuming your ATA is an un-locked SPA2102-NA).
    If you think the firmware 5.2.12 is faulty, then repeat the upgrade/downgrade process by downgrading back to an earlier version:
    http://www.cisco.com/cisco/software/release.html?mdfid=282414111&softwareid=282463187&release=5.2.12&relind=AVAILABLE&rellifecycle=&reltype=latest
    If you are still having problems, see if this tutorial will reveal any procedural issues:
    http://blog.cqvoip.net/2009/12/linksys-cisco-spa2102-updating-firmware.html
    Regards,
    Jeff - cqvoip.net

  • N80 Firmware Upgrade success!!

    I had been waiting for this firmware upgrade for the N80 since this service started. I am glad to say that the upgrade was successfull. I was a little worried because i'm not from the UK, but from South Africa and so doing the upgrade was a bit of a risk, but there was no risk!
    Finally. I'm happy now

    What is your n80 variant?
    Type *#0000# on your phone, whats the number after "NOKIA N80"
    example: (58.01)

  • E90 firmware upgrade problems

    Recently, I upgraded my E90's firmware from the version 7.xx to 300.34.84. I backed up all the data on the phone prior to the firmware upgrade - as required for the retention of software certificates and data. 
    Some of the trouble I'm having now is with the Download! folder, specifically the Applications subfolder - it does not update it's content - actually, it's totally unaccessible. Also, the Windows Live Application no longer works - and I'm unable to download a fresh copy as a result of the problems with the Download! folder. Prior to the firmware upgrade, I had using the Windows Live Messenger application and the Windows Live email/messaging synchronising facility in the Messaging folder hitch-free for about three months.
    Any ideas?  Thanks  
    By the way, I don't think the upgrade in this case has much merit. Other than the A-GPS, there's no real substance in 300.34.84.
    Symbian connected me to the world, to my dreams.. Thank-you Nokia

    I just saw a post for the exact same problem on an E71. Search 'E71 Download! folder: Service Not Available' by hazz on this site. See my problem is I'm not too interested in the third-party software available from ea.mobile.nokia.com/ea/apps/. I'm interested in the ones that become available in the Download! folder, under Applications. When I click on Applications, the chevron appears, followed by the progress bar, which fills almost completely, then shows the this message: 'Catalog update failed!' I believe my internet connection is working fine - I watch youtube on the device often.
    This week, a new link appeared - U2 - Get On Your Boots - which great, 'cause U2 rocks. But, Applications remains dead - even if I remove it from the list and click - Options/Select/Refresh List.
    I got around the Windows Live problem by using the awesome Nokia Messaging (email) [http://email.nokia.com], and the instant messaging application mxit. Besides those minor issues, I think the E90 is a pretty awesome device.
    Thanks
    Symbian connected me to the world, to my dreams.. Thank-you Nokia

  • X4600m2 bios/ilom firmware upgrade problem

    In the X4600m2 downloads, under Software 2.3, in the firmware category, I downloaded ILOM-3_0_3_31_r42822-Sun_Fire_X4600M2.ima (md5 checks out). I can't install the new firmware however (using the ILOM cli):
    -> load -source tftp://172.22.95.215/ILOM-3_0_3_31_r42822-Sun_Fire_X4600M2.ima
    NOTE: A firmware upgrade will cause the server and ILOM to
          be reset. It is recommended that a clean shutdown of
          the server be done prior to the upgrade procedure.
          An upgrade takes about 6 minutes to complete. ILOM
          will enter a special mode to load new firmware. No
          other tasks can be performed in ILOM until the
          firmware upgrade is complete and ILOM is reset.
    Are you sure you want to load the specified file (y/n)? y
    Do you want to preserve the configuration (y/n)? n
    Image is not for this platform.
    Firmware image update failed.
    ->With all previous releases this worked fine.
    Update: the upgrade on the ILOM web interface also fails.
    I'm running this version currently:
    -> version
    SP firmware 2.0.2.10
    SP firmware build number: 38791
    SP firmware date: Tue Nov 4 18:36:42 PST 2008
    SP filesystem version: 0.1.14
    Any idea why this is failing? I've tried both preserving and not preserving the configuration.
    Edited by: kaufmann on Jul 22, 2009 9:27 AM

    Quote from: renewest on 14-July-12, 19:43:52
    Are you saying that it worked before because of an error? I've worked with boards before tha supported 2 monitors, 1 on the mainboard and 1 on a graphics card.
    Quote from: renewest on 14-July-12, 19:43:52
    Are you saying that it worked before because of an error?
    Yes.. normally onboard become automatically disabled, when dedicated card is installed.

  • E71 firmware upgrade problems

    Hi,
    when I want start my firmware upgrade (today 100.07.76 - Vodafone branded) to the actual one via NSU, it stops always ~60 MB. Tried many things already, everything is up-to-date from Nokia and PC with XP.
    Any ideas ?
    cheers
    cafri
    Message Edited by michaels on 18-Mar-2009 12:33 PM

    It should not be anything to do with branding if the update starts downloading, if the branding was an issue you wouldn't even get acces to the update.
    There are conflicting stories about Nokia service points and debranding. It can only be done if the phone has had any SIM lock officially removed by the network, and the service point may in some cases ask for a letter from the operator stating their approval for the action to be taken. Service points are not required to offer this service and so may not do, and if they do it will be at your cost.

  • N80 firmware upgrade: No upgrade available.. not t...

    The nokia software updater for my N80 IE say no update available but it's not true .
    My firmware on N80 IE is v.40707.0.7 28-3-07 rm 92 I need to upgrade to 5.0719.0.2 , but when i try to update them essage says :" Not update available" .
    Where do I post my product code to solve this issue ???
    Thanks to allMessage Edited by thehawk on 23-Sep-200710:59 AM

    25-Sep-200711:25 AM
    prabin wrote:
    Hey Guys!
    To be very frank with you, first of all you have to decide why you are upgrading your firmware in Nokia N80IE?..... Recently I have also upgrade my N80IE with latest version V.5.0719.0.2 (24-05-2007)but I encountered so many problems. And it is like a one way street once you upgrade the version you can downgrade the version again. Therefore... be careful before you change the version.
    Prabin
    I know that the downgrade is not possibile ...
    Read the previous post

  • After firmware upgrade problem CP1025NW

    I am trying to upgrade the firmware on my CP1025NW printer.  I downloaded and ran the firmware updater and it runs for a bit and then reports that it "Could not find appropriate firmware file". I have tried running the updater both through a USB connection to the printer and a wireless connection. Both result in the same error.
    After that on the printer is blinking caution sign and I cant print anymore (, I think soft erase old firmware and did not record new one.
    Exist some kind of special software for an force firmware update ? or how can I restore it ?

    hi there,
    could you provide the community with a little more information to help narrow troubleshooting? What operating system are we running the update from?
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Airport Extreme 7.1 Firmware Upgrade - problems with Airdisk

    I recently upgraded the Airport Extreme firmware from 7.0 to 7.1 but have experienced several problems.
    After the initial upgrade, I encountered a double NAT warning, which was fixed by switching into Bridge mode, followed by an invalid IP address warning. I rebooted the AE and the warning disappeared.
    Connecting to the wireless network is ok, except that it can never remember my connection (which is a closed WPA2 Personal network) and I have to manually re-connect every time I switch on the nac - with my previous Airport Express this would remember the network and re-connected automatically.
    Worst of all however is that I can no longer see my AirDisk - a LaCie 500 GB USB HD connected to the AE.
    The disk name is simply upper case ASCII and so I cannot understand why this is occurring. It worked perfectly using version 7.0. Has anyone else had these problems or aware of a workaround?
    MacBook Pro (Core 2 Duo)   Mac OS X (10.4.9)  

    The 7.1 update has caused problems for many many people.
    What I did to solve problems was to revert back to 7.0. here's a link to a post I made over at jmacrumors.com explaining how to do it:
    http://forums.macrumors.com/showthread.php?p=3690572&posted=1#post3690572

  • Creative Zen Xtra Firmware Upgrade Problems v1

    While trying to upgrade the firmware on my Creative Nomad Jukebox Zen Xtra, there was a problem with the upgrade. I'm now stuck in rescue mode v.3. When I plug the MP3 player into the computer, Windows will recognize it and asks me what to do. I exit that window and try to run the firmware update again. The firmware program tells me "Your player is not connected, please connect your player."? there are 2 options "Upgrade" and "close". Upgrade is greyed out, but close is clickable. I've tried
    1. clean up,
    2. format all,
    3. reload OS and
    4. Reboot.
    None of those options seems to do me any good. I've uninstalled all the Creative software from my computer, but still no luck. Please help me. I'm doing my best to avoid having to go buy an iPod, but if I can't get my Creative Mp3 player to work, I guess I will have to. I have spent a lot of money between cables, the docking station and the leather case. I'd hate for all this to be wasted, so please help me.
    I've tried to "reload the OS" and then clicked on the language the moment the Player told me to start the update. Someone please shed some light on this for me. I've tried email Customer Support. I've searched Google. I've put my best skills on it and of course I've scoured this website to no prevail. Someone help me out.

    READ ALL BEFORE PROCEEDING You do need to install the driver. http://support.creative.com/Products...e=MP3+Players# When you get to the page for your player bottom left the manual selection choose Xp & clik submit the driver should be the first one version 2.0.00 .After the driver is installed when you plug in the player check in device manager to see that it shows up there Start>Control Panel> System>Hardware>Device Manager look under Portable Devices or for the name of the player. Use a rear USB Port to assure a good connection. Then run the firmware file on the computer ,choose reload firmware or Os on the player,choose language when player asks for update(the pop-up from windows indicating that it "sees" the device DO NOT CLOSE IT.)

  • WRT54G v8.2 failed firmware upgrade problem

    Today I tried to upgrade my WRT54G v8.2 router to the latest firmware from Linksys. But the upgrade kept repeating itself every time when the progress bar reached about 75%. This lasted more than 30 minutes and I had to stopped the upgrade. Then the router stopped working. I've reset and hard reset the router. I also tried the tftp method to upgrade the firmware again. But the problem is still there. When I ping 192.168.1.1, I constantly get the "Destination host unreachable" message. Anyone could help me fix this problem? The power light and the ethernet port light are always on. Is there any way to fix the problem? Any information is appreciated. Thanks a lot.
    Solved!
    Go to Solution.

    Do not use the wireless computer to upgrade the firmware.Hard-reset the router for 1 minute and try this link and check if that works...

Maybe you are looking for