N80 V4 Firmware and vodafone

I have recently bought TOM TOM Navigator 6 and have been having problems with the Bluetooth Connection for the GPS Unit.I have read on various forums that Firmware V4 will cure this issue, but the updater tells me I have the latest version which is V3.0617.0.6. Is this an issue with Vodafone.

Hi,
Vodafone have yet to approve V4... please see:
here

Similar Messages

N80 v5 firmware and dire battery life

Updated to the v5 firmware for the N80 (5.0719.0.2) and apart from the annoying loud warning tones, the biggest problem I have with this is the extremely short battery life now.
Charged last night, left on standby for maybe 10 hours, and the thing is flat in the morning!
I doubt the battery has suddenly died. Before updating to v5, the phone would last several days on standby.
I can't see that it is connecting to any access points during the night. Bluetooth is off. WLAN scanning is off.
I know the N80 is old now, but anyone found a solution to this or have some tips?
Only other thing I can think of doing is a total reset of phone and media memory, and reinstall everything from scratch.
E72-1 UK CV 052.005

I have had V5 on my N80 a year or more now and there is definitely no reduction in battery life.
Make sure that things you don't normally use like 3G, bluetooth and wlan scanning is switched off. If this doesn't work then try resetting and failing that, reinstall V5.

N80 On 3 And Firmware Upgrades

Hi, I'm hoping to use Navicore satnav software on my N80, but the Navicore website suggests a version of firmware higher than I have on my phone. Link below states the requirement for '4.0623.0.41 or later': http://www.navicoretech.com/Consumer/Support/Compatibility My current firmware is at 3.0618.0.2. I phoned my nearest Nokia service centre, and they were happy to discuss upgrading of the firmware, and seemed OK about doing it. However, when I mentioned I was on the 3 network, this seemed to raise some problems. I was told that the firmware for 3 is somewhat proprietary, and that my version number didn't map directly onto generic firmware versions. This being the case, they would have to connect my phone up, and see what happened when their software went looking to Nokia for information. In addition, I was told that 3 firmware lagged behind the generic by some margin. So, my queries are: 1) Is there a later version of 3 firmware than mine (dated 23-05-2006)? 2) How does it compare to the Navicore required 4.0623.0.41 version in terms of currency? 3) What are the chances of Navicore software running on 3 firmware at all? Thanks in advance, Kieran

The GENIRIC-firmware of the N80 is updated; this doesn't mean that the Operator-variants, i.e. Vodafone & T-Mobile, updated THEIR firmwares as well . . .
Nokia Software Uploader looks for the Production-Code of your GSM.
With NSU, you can NEVER change your Operator-Firmware to the GENERIC Nokia one!
See this topic:
http://discussions.europe.nokia.com/discussions/board/message?board.id=swupdate&message.id=451
Greeeetzzz, Henk.
RM-159 / Nokia N95-1 (8Gb)
V 21.0.016 (02.01) / 14-02-08

N80 new firmware release date and wishlist

It has been no update on firmware since the latest release V.5.0719.0.2 for N80 since 24 May 2007. With so many models rolling out and firmware revision released for other new and old models, one might wonder if N80 is being forgotten and the firmware revision is put on-hold forever in cold storage?!
There has been so much discussion on the expectation for last firmware release but what we get is only product stability without signficant boost of functionality and performance. I believe this has made many proud owner of N80 phone waiting with a long neck.
After reading through the forum, I have summarised some of the common expectation on the next release (hopefully) in a wishlist below. All is welcome to provide input on the improvement they expect in next firmware release. It is also hope that any status of firmware upgrade for N80 news to be shared here.
The N80 new firmware wishlist
i) AD2P bluetooth profile support
ii) Nokia Maps application support (currently, N80 is not support model for Nokia Maps application)
iii)Enhanced digital music player (similar with N73 ME with album art browsing)
iv) Music file IDD tag editing (change artist, song title, genre information)
v) Video ringtone
vi) Skype VOIP support
vii)Mymobilesite.net intergration for seamless moblogging interface
viii)Auto birthday reminder storing from Contact entry
Thats all I can think of for now.
was: 3310--> N80 v5.0719.0.2--> N82 v31.0.016; now: 5800xm v40
KeN82Ny

Hi Jacob,
Thanks for your quick response but if you go to the download section of Nokia Maps, N80 is not listed for selection on Nokia Maps setup file download. It is obvious that the compability page does show N80 is supported but which setup version to choose? I myself have Nokia Maps installed previously. But I believe there are new feature and interface in the latest version of Nokia Maps.
Yes, mymobilesite.net is available for N80, but perhaps the new firmware can include it in the new firmware release to save other the hassle to install
something to add:
ix) HSDPA mobile internet surfing speed (3.5G?)
was: 3310--> N80 v5.0719.0.2--> N82 v31.0.016; now: 5800xm v40
KeN82Ny

Gallery Bug in N80 v5 firmware?

Since i have the new V5 Firmware installed on my N80 it wont randomly display all the images that are on the storage card. All i will see then are the two Links in the gallery. The only solution to this problem is to restart the phone. Then it will display all images again.
I never experienced this problem with the predecessors of the v5 firmware and it really annoys me a lot.
Anybody else having these problems with the v5 n80 gallery?

I have had V5 on my N80 a year or more now and there is definitely no reduction in battery life.
Make sure that things you don't normally use like 3G, bluetooth and wlan scanning is switched off. If this doesn't work then try resetting and failing that, reinstall V5.

Vote of thanks For New N80 V4 Firmware

After previously moaning about my N80, I just wanted to say thanks to Nokia for the last N80 v4 firmware upgrade, so far it has made my N80 a much better, usable and stable phone.
I hope that you will provide further enhancements to this great phone.
Thanks.

18-Oct-2006
05:26 PM
dougieth wrote:
I have contacted Orange and told them to get a move on or I will be changing service provider to one that allows new firmware upgrade. All Orange users should e-mail Orange and let them see how disappointed we all are.
Been there, done that, no reply from Executive Office (yes I emailed them direct several times - much better than cust services if you want something resolved!)
I'm currently looking at my contract VERY carefully so I can shove it somewhere painfull, and move networks OR get a handset which they WILL support (which prob means not a Nokia!)
edited to removed irrelevant linkMessage Edited by orinoco on 19-Oct-2006
09:35 AM
Orange Handsets : Nokia 51 > NK702 (6130) > 6210 > 6310i (silver)> 7210i > 6230 > 6230i (silver) > N80 (silver) > N95-1
T-Mobile: N96

Latest firmware and updates!

Hello, I am new and as far as I searched this forum, I still havent found any info about latest firmware and its updates
Anyone can give me some link or something where I can see what is new in the latest update?
I am sorry if I was blind, but at least I tried to find something
Thanks
EDIT: Thats meant to be for Nokia N80 Message Edited by ikey on 25-Apr-200701:34 AM

25-Apr-200701:31 AM
ikey wrote:
Hello, I am new and as far as I searched this forum, I still havent found any info about latest firmware and its updates
Anyone can give me some link or something where I can see what is new in the latest update?
I am sorry if I was blind, but at least I tried to find something
Thanks
Well, the latest N80 Firm. is 4.0707.0.7 but it's craap. It contains a looooot of bugs u can find the bugs discussed here.
Seriously, I do not recommend updating to this version trust me i have an N80 too..Message Edited by tekso on 25-Apr-200701:38 AM
www.symbiano-tek.com

New o2 N73 firmware gives vodafone screensaver!

I have an N73 from o2-UK (0539976). I just upgraded to firmware version 3.0704.1.0.1 through NSU, turned my phone back on and it had the vodafone screensaver. Surely this should not be happening?
When you type in the different product codes for o2 n73s (0539976) and vodafone (0541044) it gives identical firmware, should that be the case?

Well the variant doesn't appear to have been changed to vodafone UK which is either a good or bad thing depending on how you look at it.
I wouldn't worry to much if it's not affecting functionality, this update will probably be pulled and updated soon, and then you'll have to install it again, hopefully the NSU team will send word to the mods as to when that will be.
First use the search to see if your question has already been answered...
Secondly I will not knowingly assist in breaking the forum rules.
My information is always changing, what I post at the time is usually true.

IMac G3 won't boot after updating the firmware and upgrading the OS!

Hi! Everyone,
I have an iMac G3 333MHz (five flavors) which comes with 192MB of RAM and 6GB of hard drive. Originally, it was OS 8.5.1 installed, later upgraded to OS 9.2.2. Of course, the firmware has been updated by the appropriate method provided by the on-screen instructions before the installation of 9.2.2. After successfully updating the firmware and installing Mac OS 9.2.2, the system booted up and worked fine. However, after shutting it down and powering it up a few days later, I have encountered a critical problem:
1. At first, the iMac would chime and displayed a smiley-mac finder face.
2. No question mark appeared and the system halted because it stayed at the same screen for about 5 minutes! Also, the keyboard wouldn't respond. For instance, the LED signal light wouldn't light on when Caps Lock was pressed.
3. I assumed that this is just a typical crash and rebooted the machine via the "reset" button on the right side of the machine.
4. After restarting, well, no luck, the same condition. Therefore, I rebooted it again by using the method mentioned above.
5. The condition of sticking at the smiley-mac finder face occurred again! However, this time the iMac wouldn't chime and just displayed the mac face.
6. Another restart, well, it was getting worse... no chime and no smiley-mac finder face but a white screen.
7. I was frustrated then and shut the machine down forcefully by rebooting it again and pressing on the power bottom quickly before the screen appears. Also, I unplugged the power cord.
---------- After a few hours later ----------
8. Okay, I then plugged the power cord in and booted it up again, this time, it would chime but stuck at the white screen. => No smiley-mac finder face appeared!
9. Rebooted it again, the result was as same as step 8.
10. Another restart, the smiley-mac face finally appeared but still... stuck here and this time, no chime.
11. I then shut the machine forcefully by using the method mentioned above and let the machine rest for about a day with the power cord unplugged.
---------- After resting for a day ----------
12. I booted it up and it would chime, but no screen (the power button was orange, not green). I then forcefully shut down the machine.
13. Waited for about a minute and powered it up. This time, I tried to clear the PRAM, but no chime and gave me a white screen. => No luck! As mentioned, the keyboard's LED signal light wouldn't light on even though the Caps Lock key has been pressed.
*Note: The keyboard has been tested on the other computers and it worked. Also, I tried different USB ports to plug the keyboard in. => The USB ports were all in working condition， as I can know from the last successful start up.
14. Forcefully shut the machine down and tried to enter the Open firmware, no luck. It didn't enter and gave my a white screen.
15. Conclusion:
1) After resting for a while, the iMac would chime.
2) Rebooting too much times would cause the machine not to chime and leaded the screen to become white instead of the smiley-mac finder face.
3) However, rebooted the machine when the screen became white, the smiley-mac finder face would appear again without chime.
By the way, I could hear the hard disk spinning up so that means the hard disk is working.
Can anyone help me solve this problem? Is it related to the firmware update? Any suggestions will be appreciated! Thanks!
Andy

OK, I will try replacing the PRAM battery. Also, the PowerMac G3 and the other iMac 233MHz had the dead batteries. They are still working though... Should I replace them along with the iMac 333MHz? In case of not replacing, will they malfunction in future times? There are some symptoms on this two machines: 1. iMac 233MHz - No chime and no sound when adjusting system volume (the bi sound is not available), but iTunes and other applications can still use the audio device and output the sound via internal speakers; 2. PowerMac G3 450MHz - Will chime but sometimes hard to boot: 1) Chime but no screen; 2) No respond after pressing the power button => the power signal light won't light on. Every time I experienced this, I would open its case, pressing a small button (not quite understand what it does... anyway, just works if system halted.) near the PRAM battery and wait for about a minute, then close the case, and it boots. However, I have to reset "Date & Time"...

HT4623 I trying to update my iPad using iTunes. After connecting to MacBook Pro where is installed all latest software iPad is recognised as iPad, Serial Number: n/a. iTunes run recovery mode, trying to restore iPad firmware, and in the end unknown error

There was some updayts for my iPad 4 automatically downloaded. After installing it, the iPad began to restart itself every few minutes.
I tryed to update my iPad using iTunes. After connecting to MacBook Pro, where is installed all latest software, iPad is recognised as "iPad", Serial Number: n/a. iTunes run recovery mode, trying to restore iPad firmware, and in the end unknown error occured (3). Tried many times, not results. And now iPad stays only in recovery mode, can't switch it off. How can I solve this problem please?

When I restart my iPad the connect to iTunes comes up and stays on until it shuts down again, I have read a report from Apple support suggesting I reinstall iTunes so I might try that again and also your suggestion which i shall also try, but thanks again - rg1547

I am from turkey and Iphone4 can be used Turkcell and vodafone(carriers) in turkey but i bought my iphone in usa and it only works with at&t.Is there anything i can do to use my iphone with turkcell or vodafone?

I am from turkey and Iphone4 can be used Turkcell and vodafone(carriers) in turkey but i bought my iphone in usa and it only works with at&t.Is there anything i can do to use my iphone with turkcell or vodafone?

No. Return it and get your money back if still within the 30 day return window. All US iPhones are carrier locked and cannot be officially unlocked.

The bottom part of my iphone4 screen cannot tap.. restored 2 times with latest firmware and yet still the same..is it possible to fix this?how?

The bottom part of my iphone4 screen cannot tap.. I restored it 2 times with the latest firmware and yet still the same..is it possible to fix this?how? please guys help me =(

iPhone and iPod Touch: Troubleshooting touchscreen response: http://support.apple.com/kb/TS1827

I connected my iphone 3g to itunes which was in 4.1 firmware and itunes ask for an update which i downloaded an updated the phone to version 6.1.3 but my phone cannot start it shows no service my sim card is not getting network and i cannot use the phone.

i connected my iphone 3g to itunes which was in 4.1 firmware and itunes ask for an update which i downloaded an updated the phone to version 6.1.3 but my phone cannot start it shows no service my sim card is not getting network and i cannot use the phone. what should i do.?

First, you do not have a 3G if you could upgrade it to 6.1.3, because 4.2.1 is the last version that will work on the 3G. So you either have a 3GS or you somehow hacked the phone to install an incompatible version. You can check the model you have by entering your serial number here: https://selfsolve.apple.com/agreementWarrantyDynamic.do
Assuming you have a 3GS the most likely reason for your problem is you have a gray market phone that was hacked or jailbroken to unlock it. When you upgraded it you removed the hack, so the phone is now locked to its original carrier.

No firmware and no contact with PC with zen visio

I wanted to upgrade firmware and followed an instruction that told me to rebuild firmware first and then install the firmware upgrade. The update program doesnt say it is docked - although it states docked in the Vision M screen.
Appreciate any helpMessage Edited by borge on 04-3-20070:50 PM

Ok, I am assuming that either pc suite is so buggy that no one has had a chance to emulate this or that no one has this issue other than me and everyone is synchronising their outlook contacts with their N70 and are still able to us voice Tags?
If anyone is experiencing this issue can they please let me know I am not the only person having this problem or preferably if anyone knows a fix please let me know so I can either ignore and forget ever using voice tags or allow me to use what would be a really useful feature?
I am beginning to think this may be like a Microsoft built in feature
Cheers, B

Firmware and third party updates

Hi Everyone,
Currently I am running ARD version 3 on tiger server and I have Tiger and Leopard OS X running on my client machines (G5, Intel Mac).
I was wondering if there is a way to send Apple firmware and third party application updates to all of my Mac clients using ARD.
I have used "softwareupdate -i -a" and this command seems to be only working with Apple software but nothing else.
1. Is there a command that I can send (using ARD) to update firmware on all my Mac clients?
2. Is there a command to update third party software such as Adobe, Roxio etc?

1. No
2. Only by repackaging the updates into an Apple standard package installer and pushing them out via ARD. I suggest you use LanREV's InstallEase (Free) to package up the updated files on your master build system and deploy those packages.

N80 V4 Firmware and vodafone

Similar Messages

Maybe you are looking for