N82 dead after software update

Good evening,
I was just updating my phone via the nokia suite, when my computer suddenly restarted.. After this incident I have been unable to power up my phone, and I fear the worst..
Is there any way to fix this, apart from turning it in for a service?
-J

First remove the battery for 5 minutes, reconnect the battery, connect it to your pc and run the updater again. Leave it for a few minutes and it should go into recovery mode.
If not disconnect it and try a hard reset.
Hard reset:
1. Switch off the phone.
2. Hold down the following three buttons: Green (the call answer button), * button, and '3' button.
3. While holding these buttons, press the power button and switch on the phone.
4. Release when the phone shows the nokia logo or shows other signs of life like the language selection screen.
If that fails to fix it try the advice offered in this post by drummer27:
/discussions/board/message?board.id=swupdate&message.id=14152#M14152
If that still fails then the last option is to take the phone to a nokia care point.
Care points/service centres and repair info:
UK • Europe • Asia-Pacific • USA •
Canada • Middle East and Africa
Elsewhere: Click here, select your country, go to the support section, then select repair.

Similar Messages

  • Nokia E52 dead after software update using Nokia S...

    I bought my Nokia E52 the day before yesterday. It is an early model (arrived at the store i September). But it worked fine, except for the bluetooth connection.
    I tried to update the software using Nokia Software Updater via the USB cable. But it lost connection (I didn't touch the cable nor the phone at the time, and the computer was workning fine). After that I tried it again a couple of time, but it lost connection. It seems the USB-micro connecter on the phone is defective. 
    Finally its seemed to worked, but after a long period of time it lost connection again and this time the phone was dead. The computer couldn't find it when I connected the USB cable and the screen was dead, nothing happend when I push the powerbutton, except it vibrated once as normal after that nothing happend.
    The screen was dead, the numberpad was not lighted. I removed the battery and waited a couple of minutes and tried again. Nothing happend. I tried to reset the phone by using buttons '3', '*', 'anwesring-bottun' and powerbutton. Nothing happend.
    Obvious the software update were unsuccesful but is my phone beyond repair? Is the warrenty/guarantee still valid?

    Your phone will be repaired in a nokia care point. Usually they fix this problem whenever it occurs during a software update. If that key combination didn't help in your case, then it's definitely a point to go to a care point. I think it is covered by warantee but I'd advise you to call the service point just in case to check with them.

  • Nokia 301 dead after software update

    I just updated my Nokia 301 from its software version 2.something to the latest (8.03 I believe). After the update process the phone is dead. It won't start up, nothing.
    Is there anything I can do?

    Beck_DK:
    we are investigating your report about Mail for Exchange.
    pbomta:
    Nokia 301 does not support SW updates via Nokia Suite (like all the more recent phones), so that would be the expected result.  
    http://www.microsoft.com/en/mobile/nokia-x-updates/
    http://www.microsoft.com/en/mobile/nokia-x2-update/
    http://www.microsoft.com/en/mobile/asha-software-update/
    http://www.microsoft.com/en/mobile/support/software-update/wp8-software-update/
    http://www.developer.nokia.com/Community/Wiki/Nokia_firmware_change_logs
    https://twitter.com/LumiaSWUpdates

  • IPhone 4S went dead after software update

    My iPhone 4S is telling me to connect to iTunes after latest software update. I can't do this as my laptop is not working at the moment. Any ideas on what I can do

    The same happens to me. It don't work in my phone the apple logo does not appear.. I tried to do a hard reset to my phone because it was frozen and now it seems like the phone is dead.. need help please..!!

  • Dead after software update

    I noticed after work tonite the software update shortcut was up with needed updates. I told it to do it and noticed later it has shut down, not restarted. I started it back up and it made it thru the tone, grey screen with apple and swirl thing and shut down.
    I tried it again watching the lights.. same thing no code flashed just stopped
    So... I tried resetting everything on the board
    This time the monitor dropped out before the computer shut off.. ahaa reset video card again.. cured... no.. now no monitor at all no chimes either no code either
    One more time..No lights no tones no monitor so I let it go and the dreaded fans slowly climbing to high speed began, shut off and started typing this on my pc.
    Main board right?
    how do I verify?
    Best place to get a replacement board? Man this is a drag.... Cant afford a new mac
    Please any help?
    Thanks Kurt

    See if you can Boot off your original G5 Install Disk while holding down Option/alt key to select AHT, then run the extended Apple Hardware Test.
    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Tiger Install disc that came with your computer, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair. Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
    If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
    The usual reason why updates fail or mess things up, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions. (Well, the Installer actually uses superuser Permissions to do it's work, but after reboot it doesn't guarantee communication with other existing needed files Permissions.)
    Some people get away without Repairing Permissions for years, some for only days.
    If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
    If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates.
    May even need to do an Archive and Install if you have room on the HD, but saves all your files and gives a new OS...
    http://docs.info.apple.com/article.html?artnum=107120
    I only use Software Update to see what is needed, then get them for real via...
    http://www.apple.com/support/downloads/
    That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.
    If all the above fails, then it appears to be time for a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
    http://docs.info.apple.com/article.html?artnum=107120
    Just be sure to select Preserve Users & Settings.

  • IMac DEAD after software update!

    HELP! I have a new-ish (january or so) aluminum iMac, worked perfectly up until the recent software update to Leopard v. 10.5.3... after the update, it began spontaneously restarting. I could only use it for a brief amount of time before it reset itself again (and usually getting stuck with applications 'Not Responding' until then). I ran the latest iMac Firmware Update, thinking maybe that would be the solution, but it only made things worse (stupid). With each reboot it got worse, and eventually got stuck in a restart loop, making it to the blue screen and rebooting before reaching the desktop. I unplugged it to let it rest a bit, plugged it back in a couple hours later, and NOTHING. no response to the power button. NOTHING. Now I have a $2200 paperweight until I can get some kind of help on this..
    fwiw, no problems post-software update on my 1&1/2 year old macbook...

    Ok, here's my latest... I've got it back running again (for now, and hopefully for a while).
    I did something similar to what the earlier poster said. hit the power button (the cd drive made it usual noise for a few seconds) then held the power button (i.e. cycled it off), then hit the power button again... it took a couple times but I heard the apple boot sound (whatever that's called) and it booted.
    I actually had to do it again cause the machine got stuck in that reboot loop again before I could do the SMC reset but the second time I was quick enough to do the shutdown.
    So far it's been up for the last 8 minutes or so...

  • Phone dead after software update failure - Error symbol

    I updated my BB device software, but the update process froze at the very end when the device is supposed to initialze. Now, when I turn on the phone, all I get is an error symbol looking like a crossed out application symbol with the number 543 underneath. When I plug the USB cable in, the computer recognizes the phone and desktop manager finds it as well, however I cannot connect to the device.
    Urgent help needed!
    Thanks.
    Solved!
    Go to Solution.

    LarsLondon wrote:
    I updated my BB device software, but the update process froze at the very end when the device is supposed to initialze. Now, when I turn on the phone, all I get is an error symbol looking like a crossed out application symbol with the number 543 underneath. When I plug the USB cable in, the computer recognizes the phone and desktop manager finds it as well, however I cannot connect to the device.
    Urgent help needed!
    Thanks.
    Error 543 is an OS error.  Follow this link to resolve it.  If you need any additional help, post back with any specific questions.
    If you find a post here helpful, please consider giving the poster some Kudos

  • P1i dead after running Update Service - any suggestions

    Hi
    My P1i appears completly dead after running Update Service.  I've tried removing the battery, fully charging the battery etc.  When i run Update Service again it just says my phone is up-to-date.
    any suggestions?

    Unfortunately, in this case, we would only be able to suggest sending the handset for service. Usually when running the Update Service, you should get the option for EXIT but also for INSTALL when you are advised that you have the latest software. If you do not have this, the handset may need to be flashed by an engineer.
    If you wish to do this, I'd recommend contacting your local support team to be advised of your nearest service location. Contact details can be found here:
    http://www.sonyericsson.com/cws/corporate/common/contact

  • IMac 10.10.3 crashed completely after Software Update - Wouldn't boot

    Hi,
    My iMac Desktop crashed completely and would not startup after software update. I accidentally clicked on the software update and now the desktop is completely dead. It does boot into "Safe Boot" mode upon click the shift button, in the Safe Boot, the keyboard and mouse is hangs and can't type anything in the username/password. Lastly, I tried command line but can find Crash logs in the CrashReporter as pasted below.
    System Software Overview:
          System Version: OS X 10.10.3 (14D131)
          Kernel Version: Darwin 14.3.0
          Boot Volume: Macintosh HD
          Boot Mode: Safe
          Computer Name: X2
          User Name: System Administrator (root)
          Secure Virtual Memory: Enabled
          Time since boot: 11 minutes
    Diagnostic Report:
    X2:DiagnosticReports root# cat Kernel_2015-04-13-183008_X2.panic
    Anonymous UUID: 
    ED5DFD2E-7807-4352-1413-690BEDB208AA
    Mon Apr 13 18:29:58 2015
    *** Panic Report ***
    panic(cpu 6 caller 0xffffff80007bfe45): "Process 1 exec of /sbin/launchd failed, errno 2"@/SourceCache/xnu/xnu-2782.1.97/bsd/kern/kern_exec.c:4060
    Backtrace (CPU 6), Frame : Return Address
    0xffffff83a4b43df0 : 0xffffff800033a811
    0xffffff83a4b43e70 : 0xffffff80007bfe45
    0xffffff83a4b43ef0 : 0xffffff8000799368
    0xffffff83a4b43f10 : 0xffffff80007dc2b1
    0xffffff83a4b43f50 : 0xffffff8000336e46
    0xffffff83a4b43f80 : 0xffffff800041eeae
    0xffffff83a4b43fa0 : 0xffffff800043a40f
    BSD process name corresponding to current thread: init
    Boot args: -x
    Mac OS version:
    Not yet set
    Kernel version:
    Darwin Kernel Version 14.0.0: Fri Sep 19 00:26:44 PDT 2014; root:xnu-2782.1.97~2/RELEASE_X86_64
    Kernel UUID: 89E10306-BC78-3A3B-955C-7C4922577E61
    __HIB  text base: 0xffffff8000100000
    System model name: iMac12,2 (Mac-942B59F58194171B)
    System uptime in nanoseconds: 1563758911
    last loaded kext at 1443586415: com.apple.driver.AppleIRController    327.5 (addr 0xffffff7f81dbc000, size 28672)
    loaded kexts:
    com.apple.driver.AppleIRController    327.5
    com.apple.BootCache    35
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
    com.apple.driver.AppleFileSystemDriver    3.0.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless    1.0.0d1
    com.apple.driver.XsanFilter    404
    com.apple.iokit.IOAHCIBlockStorage    2.6.5
    com.apple.driver.AppleUSBHub    705.4.1
    com.apple.iokit.AppleBCM5701Ethernet    10.1.2b3
    com.apple.driver.AirPort.Atheros40    700.74.5
    com.apple.driver.AppleFWOHCI    5.5.2
    com.apple.driver.AppleAHCIPort    3.0.7
    com.apple.driver.AppleUSBEHCI    705.4.14
    com.apple.driver.AppleUSBUHCI    656.4.1
    com.apple.driver.AppleRTC    2.0
    com.apple.driver.AppleACPIButtons    3.1
    com.apple.driver.AppleHPET    1.8
    com.apple.driver.AppleSMBIOS    2.1
    com.apple.driver.AppleACPIEC    3.1
    com.apple.driver.AppleAPIC    1.7
    com.apple.driver.AppleIntelCPUPowerManagementClient    218.0.0
    com.apple.driver.AppleIntelCPUPowerManagementDriver    218.0.0
    com.apple.security.quarantine    3
    com.apple.security.TMSafetyNet    8
    com.apple.nke.applicationfirewall    161
    com.apple.driver.AppleIntelCPUPowerManagement    218.0.0
    com.apple.kext.MojoKDP    1.0.4
    com.apple.iokit.IOUSBHIDDriver    705.4.0
    com.apple.driver.AppleUSBMergeNub    705.4.0
    com.apple.driver.AppleUSBComposite    705.4.9
    com.apple.driver.AppleThunderboltDPOutAdapter    4.0.6
    com.apple.driver.AppleThunderboltDPInAdapter    4.0.6
    com.apple.driver.AppleThunderboltDPAdapterFamily    4.0.6
    com.apple.driver.AppleThunderboltPCIDownAdapter    2.0.2
    com.apple.driver.AppleThunderboltNHI    3.1.7
    com.apple.iokit.IOThunderboltFamily    4.2.1
    com.apple.iokit.IOEthernetAVBController    1.0.3b3
    com.apple.driver.mDNSOffloadUserClient    1.0.1b8
    com.apple.iokit.IO80211Family    700.52
    com.apple.iokit.IONetworkingFamily    3.2
    com.apple.iokit.IOFireWireFamily    4.5.6
    com.apple.iokit.IOAHCIFamily    2.7.0
    com.apple.iokit.IOUSBFamily    705.4.14
    com.apple.driver.AppleEFINVRAM    2.0
    com.apple.driver.AppleEFIRuntime    2.0
    com.apple.iokit.IOHIDFamily    2.0.0
    com.apple.iokit.IOSMBusFamily    1.1
    com.apple.security.sandbox    300.0
    com.apple.kext.AppleMatch    1.0.0d1
    com.apple.driver.AppleKeyStore    2
    com.apple.driver.AppleMobileFileIntegrity    1.0.5
    com.apple.driver.DiskImages    389.1
    com.apple.iokit.IOStorageFamily    2.0
    com.apple.iokit.IOBluetoothFamily    4.3.0f10
    com.apple.driver.AppleFDEKeyStore    28.30
    com.apple.iokit.IOReportFamily    31
    com.apple.driver.AppleCredentialManager    1.0
    com.apple.driver.AppleACPIPlatform    3.1
    com.apple.iokit.IOPCIFamily    2.9
    com.apple.iokit.IOACPIFamily    1.4
    com.apple.kec.pthread    1
    com.apple.kec.corecrypto    1.0

    Thank you for the quick response with the link. Unfortunately, it does not have the exact fix for the process launchd:
    panic(cpu 6 caller 0xffffff80007bfe45): "Process 1 exec of /sbin/launchd failed, errno 2"@/SourceCache/xnu/xnu-2782.1.97/bsd/kern/kern_panic(cpu 6 caller 0xffffff80007bfe45): "Process 1 exec of /sbin/launchd failed, errno 2"@/SourceCache/xnu/xnu-2782.1.97/bsd/kern/kern_exec.c:4060exec.c:4060,
    I had installed ManyCam long time ago but this was removed from the command line after the first crash this morning. Removing ManyCam, didn't fix the problem.

  • My iphone 4 is dead after I updated to ios 6.1.3 it doesnt turn on and doesnt respond to itunes also. Visited Apptronix service desk but they say there is nothing they can do about it, and they have charged INR 10640 for a new one. Is there anybody same..

    My iphone 4 is dead after I updated to ios 6.1.3 it doesnt turn on and doesnt respond to itunes also. Visited Apptronix service desk but they say there is nothing they can do about it, and they have charged INR 10640 for a new one. Is there anybody with similar problem....

    Hm... Try this----> http://support.apple.com/kb/ht1808 or http://osxdaily.com/2010/12/04/ipad-dfu-mode/

  • Ipod touch4g  is not detected in pc and itunes after software update

    after software update is done. when i connect my ipod touch it is not detected in pc (windows 7) and in itunes please help me anyone.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • New iPad with retina display with 30 pin connector mirroring to TV with dvi adapter problems after software update

    Hi. Good day to everyone my New iPad with retina display 30 pin connector will not mirror to TV even with divi adapter after software update. Adapter works fine. Or is it a software glitch with IOS 7.04? I've tried resetting and reconnecting nothing seems to work.

    That's one of the weird things.. it recognizes it maybe 10% of the time. And usually, only after I do the two-button reset. Problem is.. since it won't charge above 2%, anytime I try to do a restore or anything like that using iTunes, my device shuts off and I lose whatever progress I'd made.
    So, an update... after reading through a bunch of similar complaints (there are literally 1000's of them so there's NO WAY this isn't somehow ios7 related, thanks a lot APPLE ) I decided to try a restore in recovery mode. After 3 hours and several disconnections... I ended up having to just set it up as a new iPad, as the restore did nothing. Weirdly though... as I was doing the restore in recovery mode.. I noticed I'd gotten up to a 10% charge.. higher than it's been since September, so after setting it up as a new device, I turned it off and plugged it in using the wall charger. 2 hours later and I was up to 38%. Still not great, as my iPad, before ios7 could've fully charged twice in the amount of time it took for me to now get 28% more of a charge. And that's with a fully cleaned out device.. so that really ***** and I'm now more confused than ever.
    But I'm gonna leave it overnight charging and see what I come up with tomorrow. Sadly, when I paid $600 for it in February, I never expected to have to play "wait and see" with it...

  • IPhone went bad after software update - iPhone 5 is now stuck on Itunes connect and has vertical lines

    iPhone went bad after software update - iPhone 5 is now stuck on Itunes connect and has vertical lines.
    I found a video on youtube with similar issues - http://youtu.be/Xuuqxx18-bA
    EVERYTHING HAS BEEN TRIED: Restore, Reboot, Recycle, Replacing Cables, etc....
    I don't have Apple Care, what to do? Spend more money and buy a new phone?

    Here is another person who has a problem with the iPhone 5 screen https://www.youtube.com/watch?v=sc1ZPWSA8dc and they have just received them NEW!!!!!
    I myself, two days ago purchased a  2nd hand iPhone 5 that was advertised as having a line of squares at the bottom of the screen. I Googled it and found people saying it was a screen issue and to replace the screen, so I did this and it is still happening with a new screen.
    I am starting to dislike Apple intensely after reading forum posts and watching videos where people are asking for help and telling us about issues that they are having with their phones.
    Why is Apple getting it so wrong with their updates and manufacturing that they are completely destroying iPhones that cost a lot of money and then expecting the owner to purchase another phone unless they are still in warranty.
    Apple you should be going out of your way to put things right for people but instead there is a wall of silence over so many of the issues destroying peoples phones.
    SHAME ON YOU!

  • Thin white line acroos the top of my screen after software update. Can NPRAM reset help to solve this or is it a permanent pixel problem?

    Sudden thin white line acroos the top of my screen after software update. Can NPRAM reset help to solve or is it permanent pixel problem?

    Try PRAM reset.
    Reset PRAM:   http://support.apple.com/kb/PH14222
    Best.

  • HT1338 iphone 3gs cant be activated after software update to ios5

    iphone 3gs cant be activated after software update to ios5

    What does it say when you look at Settings=>General=>About=>Carrier?
    Which version of Cydia is on your iPhone - the one with the black & white
    icon or another one? What color is the Cydia icon?

Maybe you are looking for