N82 V30.0.013 Bluetooth and Wireless LAN problems

I am using an N82, but it looks like there are similar problems with everything using similar firmware. I didn't have any of these problems with the V20 firmware that came with the phone or after the first V20 upgrade I used.
I find that my wireless LAN connections sometimes only let me browse a few pages before I get the "web connection timed out" message. If I change wireless LAN connection (I have two, mostly for testing purposes) I can continue browsing. Of course the same error may happen causing me to switch again. Sometimes it just works. Both have WPA set up and the passwords are clearly correct. If I use Real Player I can typically listen for as long as I like. Sometimes the connection to the server will drop for Real Player but reconnecting will work (don't have to change wireless LAN network). With the web browser it seems like the data connection is dead, not a server timing out - the message appears instantly. I think have seen the same problem once with my 3G connection, but I haven't recreated it. Could be my imagination!
I have never had any problems with IMAP email using either the Nokia client or Profimail on either the wireless LAN connection or 3G. It leads me to believe that there is nothing wrong with the wireless LAN side of things and it may be more to do with the web browser, or perhaps just that the email clients are only talking to one server helps (DNS problems?). Has anyone experienced similar problems with an alternative browser?
I have also found that when I get to work my bluetooth dongle doesn't connect to my phone. If I disable/enable bluetooth on my phone it will connect. I had this problem with my N80 with the first firmware I had on it and the problem went away after an upgrade.
So, it seems that both connections are fixed by turning them off and on again.

Having both routers the same IP address is a little bit confusing, but possible since each router creates it's own subnet and provides full PNAT support. Actiontec DSL modem has to have DHCP enabled since Linksys WAN (not LAN) port should be connected to one of 4 Actiontec LAN ports. Linksys should not have any configuration setup in regards of your WAN account. Just set it to dynamic address. In ohter words:
1. RJ-11 connect to Actiontec mode/router.
2. Actiontec modem should be configured to acquire an IP address from Verizon and to provide all authentication info to Verizon.
3. Actiontec modem should be configured to allow clients to acquire dynamic IP addresses -- DHCP enabled.
4. Linsys WAN (not LAN!) port should be connected to Actiontec LAN port.
5. Linksys should be configured to acquire dynamic IP address and no authentifacations.
6. Configure Linksys to be DHCP enabled or you can use static IP addresss if you want.
7. Wireless devices would be connected to Linksys and on the way to the Internet addresses would go through double NAT conversions. Any wired device connected to Linksys would have similar  features. Any device connected to Linksys should be able to connect 192.168.1.1 assigned to Linksys, but not to Actiontec.
8. To be able to connect Linksys and Actiontec would no be able to communicate unless you split 192.168.1.0/24 into smaller subnets and set specific routes in the table. But even you do so you will not be able to access 192.168.1.1 accross subnets boundary.
Hope it helps.

Similar Messages

  • Hello Everyone, I just bought a HP Photosmart Premium All-in-One Printer - C309g but i find it very difficult to connect to it via BLUETOOTH and WIRELESS on my IPAD 3...i will be very greatfull if i'll get a solution as soon as possible. Thanks

    Hello Everyone, I just bought a HP Photosmart Premium All-in-One Printer - C309g but i find it very difficult to connect to it via BLUETOOTH and WIRELESS on my IPAD 3...i will be very greatfull if i'll get a solution as soon as possible. Thanks

    Hi Tomiwa,
    You cannot print from the iPad to that printer. AirPrint and Bluetooth are completely different.
    There may be apps you can buy that will enable using that printer, but that is not an ideal solution.
    That particular printer has had many bad reviews, and is unreasonably expensive for its features. Considering that you just bought the printer, as well as its lack of AirPrint, I suggest you return it and buy a printer that supports AirPrint.

  • How to completely turn off Bluetooth and Wireless

    Hey everybody,
    I'm running Windows XP SP3 via Boot Camp and I was wondering if anyone can assist me in how to completely turn off Bluetooth and Wireless connectivity so that I can reserve as much batter life while being in class taking notes without a plug-in source, but not uninstall. I know there is a Bluetooth control panel and I disabled it there but under "connect to" its still remains there. Basically I want to have the Bluetooth and Wireless turned off completely when I startup and still have the icons shown in the taskbar to let me know that they are still there.
    Thanks!

    Joergen Thomson, I can see that you have the same thoughts like I do, I wish they could release a software that is stable and better then this.
    I dont have the energi or time to report all flaus back to cisco, this product have taking to much of my time and frustration already. Thank you so much for all the time you spend to try get this product stable and hopefully a good product.
    I have a costumer that have a webservice that is IP restricted, For now I have to define more then 93 policys openening for the same service because this doesnt handle address list and groups. And all the times I had to set it back to factory default becasue of HTTP Admin server stopped, VPN Problem, Firmware Upgrades, "Packet Loss" and so on takes alot of time becasue I need to reconfig policies back.
    For now to they release a firmware is stable I have take this piece off the network and put the back a old Fortinet 60 box.

  • 802.1x Authentication on Wired and Wireless LAN

    I have successfully configured 802.1x authentication on wired and wireless Lan. We have Cisco Switches, ACS SE and Windows AD.
    But i have one issue regarding the Single Sign on while authentication using the 802.1x with Windows Active directory the users that are login first time not able to logon but the users that have their profiles already existed in their PC then there is no issue and they successfully authenticated and login easily.
    Is there any way of login successfully for the users first time using 802.1x authentication with Windows AD like a Single Sign On?

    We ran into the same situation from time to time. We implemented 802.1x authentication using the Cisco Secure Services Client (SSC) on the windows hosts.
    At the beginning we were completly unable to logon on the maschines where no locally stored windows profile exists. After change to timeout to authenticate at the network in the SSC options we are able to logon to the network and also be authenticated by the domain controller.
    Sadly this works out often as a timing issue. Most times the user needs to try a couple of times. At the moment, I'm also very interessted in a good way to avoid this (as it seems to be) racecondition.
    Hope that someone else has any clue?

  • S10-3t bluetooth and wireless not working with windows 8

    S10-3t bluetooth and wireless not working with windows 8. I tried everything but doesn't work at all. I don't know where to find the new drivers that are comatible with windows 8 ???!!! please help me to solve this problem because i tried everything....

    Do you still have your windows7 install files ? 
    ( installation image is usually in LENOVO_PART OKRBackup/Factory ) ? I lost them :\
    if yes I fear you have to enable it in win7 and then use it in win8
    http://rzr.online.fr/q/lenovo# g470 s103t (Please Contact me if your s10-3T is booting win7 or support bluetooth, 3g)
    Lenovo S10-3t | Model Name : 0651 | Mfg Date: 2010/06/08
    Lenovo G470 | Model Name : 20078 | M fg Date: 11/03/23 | BIOS: 40CN23WW(V2.09) 06/20/2011 | CPU: i5-2410M | Linux version 3.3.4lenovog470+ (root@lap) (gcc version 4.6.3 (Debian 4.6.3-4) ) #8 SMP Tue May 1 10:23:48 CEST 2012
    OS:GNU/Linux/Debian

  • TPC-2106 bluetooth or wireless Lan

    1.Could I Add Bluetooth function into the TPC-2106
       such as add a usb Bluetooth dongle on the back of the TPC-2106 Usb Port
    2. Could I add Wireless Lan function into the TPC-2106
        such as add a usb Wireless dongle on the back of the TPC-2106 usb port

    I think that what you want to do is possible. But you have to make sure that you have drivers for the device that are compatible with the TPC-2106 (drivers for win CE x.x / I don't know which release is running on the TPC.)
    Another solution for WLAN is to place a small router next to the TPC and use it's feature to enable a wireless connexion. 
    Matthieu

  • Inline Posture between Cisco ISE and Wireless LAN Controller

    Hi,
    I was looking into Cisco ISE solution for deploying NAC.
    I have a question about the network topology.
    In  the user guide documents of cisco ISE, it is written that for Wireless  LAN Controllers (WLC) and VPN devices, an additional server, Inline Posture, is needed.
    However, in the following integration document, there is not an inline posture between WLC and Cisco ISE server.
    https://supportforums.cisco.com/docs/DOC-18121
    I  want to know if Inline Posture is a requirement, if not a  requirement, what are the benefits of having it between Cisco ISE Server  and WLC.
    Thanks & Regards
    Sinan

    Hello,
    Please go through below mentioned links which might be helpful for you.
    http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_ipep_deploy.html
    http://www.cisco.com/en/US/docs/security/ise/1.2/installation_guide/ise_deploy.html
    Best Regards,

  • Incompatible Config Free and Wireless LAN driver/manager

    Hi,
    The *ConfigFree 5.90.05AB*, available in the Satellite MCE A100-498 download drivers area, is incompatible with the wireless lan manager *Intel PROSet Utility 12.4.0.0.3* (driver *Intel PRO/Wireless 3945/4965/5100/5300 12.4.0.21.1*), also available in the same place.
    When both installed, the *Conectivity Doctor* and *Profiles* tool returns the error "+cfmain.exe has encountered a problem and needs to close. We are sorry for the inconvenience+".
    Is there any other version of ConfigFree that works with this wireless lan driver/manager version? Will Toshiba release another ConfigFree version?
    Best regards,
    FilipeSilva

    You can install what you want but please follow the exact installations order .
    It is very important.
    All offered drivers, tools and utilities are tested and I cannot imagine Toshiba will offer some new version for 3 years old notebooks.

  • MAIL and Wireless LAN

    I've put together a basic, two computer (Mac Mini Duo Core and Powerbook G4 both running 10.4.6), wireless LAN. The G4 serves as the base station and is connected to the internet via a DSL modem. I have wep security enabled 128 asccii password. I have web sharing enabled on the base station but not on the satelite (Mac Mini). I have an email account through att-yahoo and I can send and receive email on the base station. However, i can't send/receive email on the satelite?!? What do I have to do to get MAIL to work on my mini?

    I have a similar setup. I created the same mail account on both computers. Both can read and send mail with no problem. Are you getting an error message when you try to send/receive mail fromt he satellite machine?
    Jim

  • SA60-742 and Wireless LAN

    Hi
    I was told when I bought this that it had support for wireless LAN, but to me it seems that there is no such built in functionality. Am I correct?
    No button to turn on/off the wireless function, and no trace of such communication in control panel.

    Hi
    I am sure that your notebook supported wireless card. First of all you must be sure do you have one or not. Please check in device manager under Network adapters if there is wireless card listed. If not you must buy one. In your case it can be some Wireless LAN Mini PCI Card or you can buy PCMCIA Wireless card and use it in PC Card slot.
    Both solutions are ok but the second one is maybe easier because Mini PC Card must be build in on right place and it is necessary to open the notebook cover.

  • Dreamweaver and wireless network problem

    This isn't about Airport, but I couldn't find the proper place to post this, so I put it here. Please advise if I'm wrong.
    I'm running Tiger (10.4.2) on a dual G5. My husband is running Windows XP on a 2GHz Dell, and also a Dell laptop. We just moved and HE is wireless now, not me. I am hardwired to a Netgear router (doesn't seem to have a name but the number on the bottom is CD814WG). We are using RoadRunner as our ISP, as we have done for seven or eight years, since its introduction into our city. TimeWarner did our installation, and everything is fine with my machine (although my husband's problems are another issue altogether!).
    I should also say that we are in no way networked, and that is not our goal or plan. We have the Netgear router, and as I mentioned, I'm wired directly to it. We both use broadband individually, and have no need to share a connection.
    I'm not having any problems at all with my broadband connection -- internet and Mail are fine -- but since the installation of the Netgear router I can't use Dreamweaver to upload HTML pages I create. I can use Fetch just fine, which doesn't surprise me since I've always powered right through my firewall with Fetch, while I always had to turn it off, with Dreamweaver. And of course I should say that my firewall is down when I have the uploading problem. The built-in OS X firewall is currently the only one I have installed, BTW.
    When I try to upload, DW gives me a dialog box saying "Dreamweaver cannot determine the remote server time. The Select Newer and Sychronize commands will not be available." And of course I can't upload anything.
    Any ideas? I have the information the TimeWarner guy left here so I can go onto the Netgear admin page, but I don't know what to change/add so that I'm able to upload with DW. It's my understanding that port 80 is for internet connections, but as I mentioned, it's not blocked -- I can go online just fine. It's just that I can no longer upload HTML pages with Dreamweaver.
    Thanks in advance...

    I'm getting the same error message as you (Dreamweaver cannot determine the remote server time...).
    I found that I could no longer upload with Dreamweaver (or see all the remote files) but I could with Transmit. However (and here the similarity ends) when I turned off the OSX firewall everything was fine.
    This didn't make me feel very easy, however, as I preferred having the firewall up. I found that it would work with the firewall up if I checked the "use passive FTP" box in Remote Info in the Site Definition menu.
    The Netgear router also has an NAT Firewall but I am using a Netgear router too, both hardwired on my iMac (via Airport Extreme - don't ask!) and wirelessly on my laptop. I haven't configured the firewall on that at all (I wouldn't dare!) and I'm getting through OK now. Try the passive FTP thing; it might work!

  • Broadband/internet and wireless connection problem...

    Towards the end of 2101 I received an email informing me that BT would be upgrading my local line and I could expect a much improved service. Whether this 'upgrade' has been the cause of my problems or is merely coincidental I cannot say. Prior to my experience since this time I could count lost broadband in hours per year (I never had internet or wireless connection problems). 
    Since the end of 2010 I now regularly lose my broadband completely every six to eight weeks. 'Home Hub cannot connect to broadband.' There is a worsening loss of speed? over a period of two to four days at the end of which I need to phone BT three/four/five, etc. times until they manage to locate the problem and fix it. It is always some problem they find on the line or with their equipment.
    I always mention that this is an ongoing problem. Never do they take any action to escalate the issue.
    This week things have become considerably worse.
    I have started to lose my internet connection now. 'Safari cannot connect to the internet'.
    There are now two issues which arise concurrently.
    I phoned BT, finally the operative in India (through a very poor BT wireless phone connection) changed the channel of my router for me. He mentioned something about changing the address and password. This seriously exacerbated the situation. My password is not recognised now when I am asked to reconnect by selecting a network.
    The next occasion on which I lost my INTERNET connection and tried to reconnect I got the message 'Airport has the self-assigned IP address (...........) and is unable to connect to the internet.
    I phoned BT to report this and was told that this indicated an adapter problem and the problem was now out of BT's hands. I Should contact Apple. 
    I did so. Apple said I should contact BT to change channels. I explained this had caused the problem and they were now refusing to assist me. Apple tried everything that they could think of to resolve the issue (despite not being required to do so). Eventually the only suggestion they could make as BT had refused to help was to reinstall my operating system. Extremely drastic. But I can now connect wirelessly again.
    Service is still intermittent requiring constant restarts to regain connections.
    BT's response to a formal complaint was more of the usual banal questions, the usual tests, the usual promises of 'something would be done'.
    Their systems are not set up to make any sort of accurate diagnosis of customers' issues. They seem to have a set number of 'fixes' into which they try to fit all problems - one would assume simply to save costs - their cost saving exercises are now costing me money.
    That's all for starters.
    Any suggestions?
    Solved!
    Go to Solution.

    fredderf99 wrote:
    I have a similar problem, since BT "upgraded my broardband" my home hub looses internet connection at least twice a day and I have to power reset it. the broadband shows as connected but the internet connection is lost, if I try reconnecting it fails and only a power resetr will work. I have a temp solution by fitting a time switch to the mains adaptor and reseting it at 0200 each day. but before the upgrade the home hub had worked for years and no problems. i have also replaced the origonal home hub 1 with a home hub 2 to see if that improves the situation.
    welcome to the forum
    This subject has been marked as solved by the originator and you will get more response if you start your own subject rather than continue here.
    if you start your own subject just cut and paste your post and then in order to help please can you post the adsl stats from your router may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or use a-z, if netgear enter 192.168.0.1) and run btspeedtester (MAC users may have problems) http://speedtester.bt.com and post the results .
    are you connected directly to the NTE5 master or test socket or to somewhere else? Do you have any phone extension sockets in your home?
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    Someone may then be able to offer help/assistance/suggestions to your problem
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Bluetooth and Finger sensor problem

    I am using Windows Vista HP PAVILION DV5 1104TU FZ 730PA ENTERTAINMENT PC. I am not able to connect automatically my cellphone Samsung with PC via bluetooth. Every time i have to select a file and send it through bluetooth file transfer wizard manually. Second query is about that the biometric finger print sensor is not working. In fact device manager doesn't show the driver..Kindly help

    Hello Khushii,
    Welcome to the HP Forums!
    I understand you are experiencing Bluetooth and FIngerprint issues on your Windows Vista computer. I will do my best to troubleshoot the issue with you!
    To fix the Bluetooth issue, you need to follow the steps in this document: Fixing Bluetooth Problems
    As well, check to see if the Samsung can work properly with a different Bluetooth device.
    In regards to the Fingerprint issue, I believe installing the driver is a good place to start. Here is the driver that needs to be downloaded and installed: Validity Fingerprint Sensor Driver
    If for some reason the issue is still not resolved, you can find some other suggestions in this document: Troubleshooting a Fingerprint Reader (Windows 7, Vista, XP)
    Please let me know your results. Thanks and have a great day!
    Mario
    I worked on behalf of HP.

  • HP Updated USB and wireless Lan Failed to install

    my USB Hard drive cant be found and i've noticed the Intel USB 3.0 extensible host controller FAILED to install the update , and also the Ralink Wireless network driver update / LAN also failed to install , i have tryed other USB hard drives and they also cant be seen , whats the fix for this Please , Thanks 
    This question was solved.
    View Solution.

    Hi,
    Happy Computing!
    Jaco
    Errare humanum est.

  • Making Bluetooth and Wireless Internet on a IBM ThinkPad T41 work

    Hello Everybody,
    I’ve bought a second hand IBM ThinkPad T41 yesterday. I want to connect wireless with my wireless internet point. But I’ve come to notice that there isn’t any wireless support on my ThinkPad 41T. Also I want to make an original Bluetooth connection point on my IBM ThinkPad T41.
    My question is: what is wise to do first, is it wise to check in my ThinkPad to search my wireless component (and how do I do that). Or should order parts in order to make the wifi and Bluetooth work on my ThinkPad. And so where is the best place to buy and witch parts do I need?
    Thank you for reading my question, I hope someone has the answer.

    To add Bluetooth you would need to replace the existing modem card with the following FRU; 91P7315 ThinkPad Integrated Bluetooth with 56K Modem (BMDC) for T40/p, T41/p.  Then you would also need to install the Antenna FRU; 13N5515 Bluetooth Wireless Antenna Assembly XGA.
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

Maybe you are looking for