N900 still restarting after update,

my n900 restarts everytime it goes to sleep wether it times out or i use the slide lock thing, i have flashed the firmware with the newest and the oldest ones using the NSU and the flasher util, I have also flashed the emmc.
The code when using terminal with cat /proc/bootreason is 32wd_to everytime. The only time it doesnt reboot is when I have media player open playing a song in which case it work as it is suppoed to. I can use the device for hours without a reboot aslong as I dont let it go to sleep.
Any ideas im stuck I have not installed any apps since flashing firmwares and emmc and have tried the echo 0 > /sys/power/enable_off_mode fix with no avail.
Any help?

The latest firmware (well, 2.2009.51) fixes the most common bug that caused handsets to reboot.. however, as stated in the bug thread on bugs.maemo.org, if your device keeps rebooting especially after a firmware update, it is very likely to be a hardware problem..
Which firmware versions have you used?

Similar Messages

Installed latest iOS on my iPad mini, it got stuck while restarting after update. It is still in that stage even after 7 hours.

installed latest iOS on my iPad mini, it got stuck while restarting after update. It is still in that stage even after 7 hours.

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Stop requiring system restart after update

I turn on my machine. Acrobat says there's an update available. I let it update. Then I get a dialog saying:
"You must restart the system before using Acrobat. Click Restart Now to restart automatically".
Come on! It's 2010... Requiring system restart after update is sooo 1990's...
Or put another way, I cannot remember when another app required system restart after updating. Only Acrobat does this nowadays. Please, stop this madness!

While Adobe doesn't deliberately try to annoy users,
it does not deliberately try to remove documented annoyances either.
There are still bugs in Acrobat 9 which have been documented for years, and no one seems interested to fix them.
Serious flaws ... like crashes and corruption of PDF files so they cannot be saved. Hours of work lost.
Every 3rd time I select the Crop icon, I can expect Acrobat 9.4.5 to crash.
There is no excuse for an app to require full reboot on update. C'mon, spend some time at
Microsoft Tech Support and figure it out. Acrobat is also the last application I can remember
requiring reboot.
I turn off Auto Update on both Acrobat and Windows.

HT4623 My ipad2 is not restarting after updating to iOS7, I now only get the apple symbol? Please advise what I need to do to get it working again. Thanks.

My ipad2 is not restarting after updating to iOS7, I now only get the apple symbol? Please advise what I need to do to get it working again. Thanks.

Try reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

Mac won't restart after updating to OS X Mountain Lion

Mac won't restart after updating to OS X Mountain Lion. Please help?

Like what happens? Is it just spinning?
If you've waited sufficiently long (say 10 minutes) you could just hit the power button which will do the trick. A little more gentle would be to open a terminal window (if you can) and type 'sudo reboot' (without the quotes) and enter your password when it asks. That will do it too.

HT204347 My MacBook Pro won't restart after update to lion

My Mac book pro won't restart after updating to lion ! Said problem a cured at startup press any key ! No Goodrich

Press and hold power button for up to 30 seconds. Remove battery and reinsert then repeat.

HT2827 i just updated my software for the apple tv and the light is flashing and it wont restart after update thoughts?

i tried to update my software for apple tv and it will not restart after update. flashing lights

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

My MacBook Pro won't restart after updating iTunes, and so the update doesn't work. I have just purchased an iPad mini and can't sync it - can anyone help?

My MacBook Pro won't restart after updating iTunes, and so the update doesn't work. I have just purchased an iPad mini and can't sync it - can anyone help

Press and hold power button for up to 30 seconds. Remove battery and reinsert then repeat.

MBP 17" will not restart after updating Java... why?

MBP 17" will not restart after updating Java...why?
It would actually try to restart for about 10-15 seconds but would quit and then shut down. Tried using P_R_Command_Options but that too failed and again it just shut down. Tried using D at startup which ran a test of the hard drive. No issues there which tells me there's a software problem.
Can any one help?

Disk Utility suggest reformating
Reformatting is not a Recovery Aid. When Disk Utility suggests reformatting, it is because it considers your drive unsalvageable. Yes, you lose all the data on the drive when you reformat.
And yes, Mac OS X Extended, journaled is the method you will need for a Mac OS X Boot drive.
You should also consider buying a replacement drive to have on hand the next time this internal drive gives you the slightest bit of trouble. Possibly an external enclosure to put it in as well. and it would not hurt to go ahead and Install Mac OS X on it and try booting from it, to make sure it is ready.
And make sure your Backups are current, as the next time that internal drive screws up you may get no warning whatsoever.

Restarting after update - Windows has encountered a critical problem and will restart in one minute?

This is a worrying one - I updated Reader today and restarted after it promted me. Soon after the pc rebooted I got an error message that said "Windows has encountered a critical problem and will restart in one minute". After it restarted, I checked the event logs and came up with this error: "A critical system process, C:\Windows\system32\lsass.exe, failed with status code 1. The machine must now be restarted.". This has never happened before and I want to know if the Reader update did anything bad. I restarted several times afterwards and it didn't happen again, but still.. it's worrying me. Is this a common error after the update or am I missing something? Running Windows 7 Home Premium 64-bit

I understand that you are worried.
I have a very similar setup as yours, and nothing happened after the Reader 10.1.3 update. The one difference is that the update did not prompt me to restart Windows. (It did prompt me on several other [XP] systems.)
Let's wait and see if anyone else encountered a similar problem.

Speakerphone still lame after update

I was just reading a thread on this, but cant find it now. I guess it was deleted.
My speakerphone is still lame after the update, (unless I am in a totally sound free environment). My verizon razr probably has twice the volume.

Hi macu,
Thanks for using Firefox OS and for reporting this issue. Can you tell me your provider or country (in case we have a known bug on this it will help me to find it)?
If you hold the power button and select Restart from the menu to reboot the device, does the notification appear again? If the rest of the system is working and you definitely have v1.1 installed (with the search box on the home screen). It is safe to ignore and should not prevent or block further updates. (But, we will file an issue for it to let the provider and OEM know about it.
Best regards,
Michelle Luna

Lockup on first restart after updating OS and wireless was left on.

Hi everyone,
I was wondering if there were any steps to take if you experience a lockup right after updating and restarting your Mac Book Pro to 10.4.6 starting from 10.4.5 with wireless previously configured and left on ?
Thanks !

I deploy a lot of X230 laptops and have been dealing with this issue. Since I cannot find any information about the cause and how to fix it I started looking more into it. The "No internet access" yellow icon starts appearing after installing items from System Update. So, with a new X230 I applied all Windows Update (which installed without issues) before going into System Update. After doing the Critical and most of the Rcommended (don't care for Access Connections) I proceeded to the Optional updates which I installed one at a time. When I installed the WiFi Driver for Intel cards 7(64), Version 15.6.1 and rebooted the system the yellow icon appeared with the "No internet connection" status. Everything still works though, I can still connect to the internet. Doing a driver rollback does not fix the problem. I did a system restore from a restore point prior the last System Update and the yellow icon went away. finished the rest of the Optional updates except the WiFi driver and all is well. This is what I did and went through, not sure if it will be the same for everybody. But Lenovo needs to look into that driver version.

Iphone 5 keeps restarting after update of 7.1.2

Hello Everyone,
I have iphone 5. After updating ios 7.1.2 phone keeps restating itself until battery die. Rare time I can see my home screen during restart. I can't do anything to my phone.Touch doesn't work. But when I connect my phone to itunes it shows me everything. Even I have backed up my photos to my pc when phone was restarting. Warranty is expired. Pls help if anyone have idea regarding this issue.

My iPhone 5 started the restarting problem after I updated (OTA) from ios6 to ios7.1.1. The restarts became so frequent that the phone became impossible to use. I then bought a cheap android phone as I believed apple were going to release an update to solve the issue. Imagine my disappointment today after upgrading to ios 7.1.2, and immediately after the upgrade, the phone goes back to the restarting loop!! I doubt that restoring the phone will do any good, I restored mine many times after my previous upgrade.......& still the problem persisted.I am not prepared to go through that pain again. I think I will just save-up & get myself the Galaxy s5 (never thought I would live to see the day that I would say this ). I am deeply disappointed by apple .

How can I keep my old stock still running after updating to Maverick ?

OK --» I bought a wonderful Architect software, but surprise ! it works only with higher OS than 10.6.8....
I know my stuff is OLD and I'm okay to update to MAVERICK, but !! I don't want to lose my old softwares that I know by heart !
So, I was thinking : if I make a BACKUP on a large USB Key... Will I be able to start my old Photoshop CS (for example) from the key ?... or something like that...
In the past, this option worked (from a external disk) from my very old iMac... but am wondering if it still could be possible ?
And BY THE WAY : my new ARCHITECT software has been downloaded to my actual 10.6.8 (but does not start...) will it STILL BE THERE after updating???
Thankssssss a LOT for your support !
Isabelle

You need to know that "USB Key" technology may not be appropriate for a system disk. Check out "wear leveling" on Wikipedia for a sobering discussion of the service life of solid-state drives. Also read "solid-state drives" (Ibid.) for a detailed comparison with hard disk technology.
--Gil

Help...MacBook Restarts and Restarts After update ...won't stop

Hello, I just ran the Leopard 10.5.1 software update on my MacBook and it restarted and now it just keeps restarting and makes the sound and it won't stop. Does anyone know what's going on?

That just happened to me. Help. I just did a regular software update, which included a combined operating system update, a QuickTime update and a security update. I restarted after the download as instructed, and now the computer keeps restarting. The little dial keeps spinning and the Apple restart bell goes off, but it never finishes. Then after a few minutes, it restarts itself again.
I've got a big college project in that computer and it's due Monday. Please someone help.

N900 still restarting after update,

Similar Messages

Maybe you are looking for