N95-1 FW V21.0.016 query...pls help!!!
anybody suffer any problems for this new FW v21.0.016 for N95-1 upgrade? if i don insert memory card , everything seem OK after fresh upgrade...but when i restore back back-up folder via PC suite b4 upgrade (only bac up all phone memory data) & insert my Sandisk 4GB memory card which got mp3, photos...& start my phone...cannot boot up forever...hang..no choices u hav to take out battery...when open menu also very slow like goin to stop...
Yes I have problems too, I backed it up, charged it, connected to Nokia Charger with Nokia supplied memory in. Half way through it said error, remove battery and power, reapply and push power switch. Then it said it was disconnected but it was not and it has been dead ever since. I have tried other usb slots, battery only, battery and another charger.
One thing though. With battery only at least it vibrates when you push the power switch. Add the charger and it does not. Also on battery only, a few devices momentarily show up as being connected, just to vanish again.
I have a feeling it is dead now as it just sits saying nokia.
Message Edited by 1tonnefc on 16-Apr-2008 11:24 AM
Similar Messages
-
N95 camera problem v21.0.016
Need help!!! After updating my N95 into v21.0.016, the quality of the camera degraded... I don't know if its the flash.... the flash still flashes but seems that it doesn't have any effect in the image.... TO explain further, I'll give an example: Before, when I take a picture on newspapers or books, I can clearly read the letters printed on it, but now, after upgrading, it's blurred, I can't barely read the letters....
The only good side of this upgrade is that the battery life increases... But still, it really sucks... I want my original camera quality back...try updating again....im guessing u did a data restore?
instead of doing a data restore try dragging all ur data onto ur desktop and use the same method to replace the data to ur phone......rather than doing a backup
also try to reformat your memory card(this will delete all your data) so make sure u save everything u want via a drag and drop to desktop method
after uve saved everything reinstall the fw
hope this works -
I have a row output like this
select * from test;
s.no C1 C2 C3
1 a1 b1 x1
2 a1 b1 x2
3 a1 b1 x3
i want the output as with the new added column as like this
s.no C1 C2 C3 C4
1 a1 b1 x1 a1
2 a1 b1 x2 b1
3 a1 b1 x3 x3
pls help me in this query its urgent for the solutionHello,
So, what is the complexity in this query? Would you like to mention from where you will get that C4 column?
-Ammad -
Hi all,
I m creating a table dynamically and after that i m inserting records in tht table dynamically..
After tht i want to fetch all the records from tht table into a cursor which is a SYS_REFCURSOR. as i have to return the data to frntend ..
But when i m opening tht cursor like
OPEN cur_GetCertDetails
FOR
SELECT TRIM(certrefno) As CertNo,
TRIM(damagedno) As Damagedno,
TRIM(personname) As Name,
TRIM(icnumber) As Icnumber,
TRIM(coursename) As CourseName,
TRIM(organiser) As Organiser,
TRIM(location) As Location,
TRIM(TO_CHAR(startdate,'DD-MON-YYYY') ||' ~ '||
TO_CHAR(enddate,'DD-MON-YYYY')) As StartEndDate
FROM ACprintInductionCert;
Its giving error as
64/5 PL/SQL: SQL Statement ignored
73/10 PL/SQL: ORA-00942: table or view does not exist
Dynamically created table name is ACprintInductionCert
Pls help me out ..
I have tried to use EXECUTE IMMEDIATE after FOR but its givin errsince your table is created dynamically, you can not
have the name hardcoded in the cursor....which is precisely the point (or one of them) I made in your Procedure Problem Urgent on this topic.
Once you start down the road of dynamic code execution it is very difficult to stop. Dynamic code has its uses but it should be very much the last resort. Dynamic code means you are literally running untested code in a production environment, and is consequently more likely to fail. Its failures are also more difficult to recover from. It also makes dependency tracking extremely difficult.
Cheers, APC -
Hi all
i am new to abap
I have the following requirement.
kindly help me how to write the select queries to achieve it.
its urgent
pls help me
thanks in advance
In June of year 1, new budget prices must be determined for the following year (year 2). The budget prices for year 2 are calculated out of the average contract prices in the first 5 months of year 1 (January May). The average contract price will then (outside the system) be corrected with an index. To calculate new prices for Campina Netherlands, a report is needed to show all materials with current budget price, volumes and contract prices during the first five months of year 1
The purchasing assistant creates an excel file per Material type, based on the Budget pricelist out of SAP.
Purchasers check the file on:
 being correct,
 materials marked for deletion in SAP
 changes to be made in data
The new prices, calculated based ion the output of the SAP Budget pricelist, are sent to controlling in june year 1.
On the 1st of January year 2 the new budget prices are inserted in SAP as the new standard price / budget price.
the fields for display are as follows
<b>table</b> <b> field<b>[/b</b>] <b> description</b>
ekko ekorg pur org
ekpo matnr mat no
makt maktx mat des
cawn zunspsc unspsc code
mbew stprs standard price
mbew peinh price unit
mara meins base unit of measure
s012 menge purchsed amount of mat
in month 1
s012 menge purchsed amount of mat
in month 2
s012 menge purchsed amount of mat
in month 3
s012 menge purchsed amount of mat
in month 4
s012 menge purchsed amount of mat
in month 5
ekpo netpr net price on date criteria 1
ekpo peinh price unit
ekpo bprme order price unit
ekpo netpr net price on date criteria 2
ekpo peinh price unit
ekpo bprme order price unit
ekpo netpr net price on date criteria 3
ekpo peinh price unit
ekpo bprme order price unit
ekpo netpr net price on date criteria 4
ekpo peinh price unit
ekpo bprme order price unit
ekpo netpr net price on date criteria 5
ekpo peinh price unit
ekpo bprme order price unitHi,
DATA: begin of i_ekpo,
menge........
netpr............
date ..........
end of i_ekpo.
Select menge netpr date
from ekpo
into table i_ekpo
where ....
if sy-subrc = 0.
LOOP AT i_ekpo.
v_month = i_ekpo-date+4(2).
CASE v_month.
WHEN '01'
itab-menge1 = i_ekpo-menge.
itab-menge5 = i_ekpo-menge.
itab-netpr1 = i_ekpo-netpr.
itab-netpr5 = i_ekpo-netpr.
WHEN '02'.
itab-menge1 = i_ekpo-menge.
itab-menge5 = i_ekpo-menge.
itab-netpr1 = i_ekpo-netpr.
itab-netpr5 = i_ekpo-netpr.
WHEN '03'.
itab-menge1 = i_ekpo-menge.
itab-menge5 = i_ekpo-menge.
itab-netpr1 = i_ekpo-netpr.
itab-netpr5 = i_ekpo-netpr.
WHEN '12'.
itab-menge1 = i_ekpo-menge.
itab-menge5 = i_ekpo-menge.
itab-netpr1 = i_ekpo-netpr.
itab-netpr5 = i_ekpo-netpr.
ENDCASE.
APPEND itab.
ENDLOOP.
Please be more specific with some sample outputs how is should be. -
N95-1 Firmware v21.0.016 Changelog
I am the one asking
Based on Nokia site, the changelog:
1. Flash Lite 3
2. Widget
3. Standby-Time Improvements
4. Improvements to Bluetooth Headset Interoperability
Actually what is the changelog beside those as nokia has never released full changelog?Wow...
Thanks a lot. Never know there are many other website reviewing it.
Quoting from symbian-freak.com :
New features:
* Flash Lite 3 support added
* Widget (Web runtime) support added
* Default year changed to 2008
Improvements:
* General stability improvements.
* Pre-defined access point kept after switching to different type SIM card.
* Localization improvements.
* Standby time improvements.
* Improvements to BT headset interoperability.
* Improvement to Calendar data restoring.
* Switch from landscape to portrait mode & screen rotations improvements.
Browser:
* Improvement to long text writing to web page text boxes.
* Browsing from WLAN wizard improvement.
Media Player:
* Localizations improvements in Music player.
* Windows Media Player recognizes device as Nokia N95.
Gallery:
* Image rotation improvement in album view.
* Gallery & Slideshow performance improvements.
Messaging:
* Improvement to SMS reception.
Java:
* Midlet installation improvement.
* Improvement to Java application start.
* Java midlet certificate checking improvement.
Navigation:
* General improvements to Maps application.
* Localization correction to Search in Maps application.
* Improvement to Navigate To –function when started from search application.
SIM:
* Contact names with accents and more than 11 characters can be copied to SIM card. -
Error in Query (Pls help)
Hi friends,
When i executed one of the queries, i get this error:
Abort System error in program <b>CL_RSDM_READ_MASTER_DATA and form_sidval_direct</b>
Diagnosis
This internal error is a targeted termination since the program has an incorrect status.
Procedure
Analyse the situation and inform SAP.
I have check all my infoobjects and master data...everything is in active but still i dont understand why i get this....
please suggest how to get rid of this error? its urgent
Regards
BalajiHi balaji,
This can be program error, need to apply support package or correction,
seems no oss found for form_sidval_direct .....
perhaps it's sid error, try to analyze and repair the infoprovider where the query created on, use transaction RSRV.
hope this helps.
assign points if useful
Regards,
Archna -
Large number of attributes reduces data display in Query (PLS HELP).
Dear Guru's
We have newly upgraded our system to 7.0, Currently i have a Query based on master data info object(0 equipment) which contain several attributes, due to huge number of attributes, i cannot see data for few attributes( Ex:-0service descrip), but data exists for these atrrib, when i check in RSA1. my client want to use heavy number of 0Euipment numbers(nearly 10000) in selection screen. thats the reason for data not to be seen.
WE are under SP 16 also(Note 562162 - Additional selection of attribute reduces query result set is allready exists), and did not found any proper note.
So guru's can any one please tell me how i can get the data in Query for these attribute by keeping the same selection option for Equipment numbers (10000).
Dude's give me some good suggestion please...client is waiting from 1 week
Thanks in adv
Dev
Edited by: Srinivas dev on Jun 10, 2008 11:52 AMDear Yogesh,
Thanks a lot dude...
I assigned points for your kindly help....
Got any idea about by initial post Large number of attributes reduces data display in Query
Thanks and Regards
Dev -
Ok heres the table I hope u can see it...
date id citypair tail delay_minutes
1/1/2007 1 BZEIAH 466 10
1/2/2007 2 BZESJO 467 16
1/3/2007 3 BZEMIA 468 22
1/4/2007 4 BZELAX 469 21
1/5/2007 5 BZEYYZ 470 10
1/6/2007 6 BZEGUA 471 5
1/7/2007 7 BZETGU 472 8
1/8/2007 8 BZELIM 473 19
1/9/2007 9 BZEJFK 474 27
1/10/2007 10 BZEBOS 475 3
I would like to get the following, to add a new column where i get these
(all the flights that have a delay>15) / (count(id))
thank you for the help.....(all the flights that have a delay>15) / (count(id))I would understand if it was for the current id on a row, but in your case, all rows will have the same value...
How I see a logic business rule :
SQL> select * from tbl_airplane;
DT ID CITY TAIL DELAY_MIN
01/01/07 1 BZEIAH 466 100
02/01/07 1 BZEIAH 466 10
01/02/07 2 BZESJO 467 16
01/03/07 3 BZEMIA 468 22
01/04/07 4 BZELAX 469 21
01/05/07 5 BZEYYZ 470 10
01/06/07 6 BZEGUA 471 5
01/07/07 7 BZETGU 472 8
01/08/07 8 BZELIM 473 19
01/09/07 9 BZEJFK 474 27
01/10/07 10 BZEBOS 475 3
11 rows selected.
SQL> select dt, id, city, tail, delay_min,
2 count(case when delay_min>15 then 1 end) over (partition by id) / count(id) over (partition by id) avg_delay
3 from tbl_airplane ;
DT ID CITY TAIL DELAY_MIN AVG_DELAY
01/01/07 1 BZEIAH 466 100 ,5
02/01/07 1 BZEIAH 466 10 ,5
01/02/07 2 BZESJO 467 16 1
01/03/07 3 BZEMIA 468 22 1
01/04/07 4 BZELAX 469 21 1
01/05/07 5 BZEYYZ 470 10 0
01/06/07 6 BZEGUA 471 5 0
01/07/07 7 BZETGU 472 8 0
01/08/07 8 BZELIM 473 19 1
01/09/07 9 BZEJFK 474 27 1
01/10/07 10 BZEBOS 475 3 0
11 rows selected.
SQL> Nicolas. -
Newbie query .Pls help!!!
Hii
All,
i have started using java very recently.Now for a forthcoming project in jsp/servlet i am trying to install necessary things.
my os :windows 2000(prof).
java :jdk1.4
servelet --jsdk2.0
tomcat :jakarta-tomcat3.2.3
Tomcat is installed by unpacking the tar file.
i have compiled normal java files and also that using servlet classes successfully.
i have set the classpath from my computer -->properties-->advancec-->environment variables as follows
classpath =C:\jdk1.4\bin;C:\jdk1.4\lib;C:\JSDK2.0\lib\jsdk.jar;C:\jdk1.4\lib\tools.jar;C:\jakarta-tomcat-3.2.3
JAVA_HOME=C:\jdk1.4
SERVLET_HOME=C:\JSDK2.0
TOMCAT_HOME=C:\jakarta-tomcat-3.2.3
NOW I AM GETTING THE FOLLOWING ERRORS IN TWO CASES :
1. when i am trying to run servletrunner i am getting the following output:
C:\JSDK2.0\bin>servletrunner
servletrunner starting with settings:
port = 8080
backlog = 50
max handlers = 100
timeout = 5000
servlet dir = .\examples
document dir = .\examples
servlet propfile = .\examples\servlet.properties
java.net.BindException: Address in use: bind
at java.net.PlainSocketImpl.socketBind(Native Method)
at java.net.PlainSocketImpl.bind(Unknown Source)
at java.net.ServerSocket.<init>(Unknown Source)
at java.net.ServerSocket.<init>(Unknown Source)
at sun.servlet.http.HttpServer.run(HttpServer.java:222)
at sun.servlet.http.HttpServer.main(HttpServer.java:432)
there is no IIS running in my pc .
2) when i am trying to browse a jsp page in tomcat (even the example .jsp pages given with tomcat) ,i am getting the following errors:
Error: 500
Location: /examples/jsp/num/numguess.jsp
Internal Servlet Error:
java.lang.NoSuchMethodError: javax.servlet.ServletException.getRootCause()Ljava/lang/Throwable;
at org.apache.tomcat.context.ExceptionHandler.doService(DefaultCMSetter.java:289)
at org.apache.tomcat.core.Handler.service(Handler.java:287)
at org.apache.tomcat.core.ServletWrapper.service(ServletWrapper.java:372)
at org.apache.tomcat.core.ContextManager.handleError(ContextManager.java:1183)
at org.apache.tomcat.core.Handler.service(Handler.java:312)
at org.apache.tomcat.core.ServletWrapper.service(ServletWrapper.java:372)
at org.apache.tomcat.core.ContextManager.internalService(ContextManager.java:812)
at org.apache.tomcat.core.ContextManager.service(ContextManager.java:758)
at org.apache.tomcat.service.http.HttpConnectionHandler.processConnection(HttpConnectionHandler.java:213)
at org.apache.tomcat.service.TcpWorkerThread.runIt(PoolTcpEndpoint.java:416)
at org.apache.tomcat.util.ThreadPool$ControlRunnable.run(ThreadPool.java:501)
at java.lang.Thread.run(Thread.java:579)
please help me to sort out these problem .
regards
Arnabhii
in addition to what i hav written earliar ,i would like to add over here the error i am getting while executing the startup.bat file
C:\jakarta-tomcat-4.1.24-LE-jdk14\bin>startup
Using CATALINA_BASE: C:\jakarta-tomcat-4.1.24-LE-jdk14
Using CATALINA_HOME: C:\jakarta-tomcat-4.1.24-LE-jdk14
Using CATALINA_TMPDIR: C:\jakarta-tomcat-4.1.24-LE-jdk14\temp
Using JAVA_HOME: C:\jdk1.4
java.lang.NoSuchMethodError: java.util.logging.Logger.logp(Ljava/util/logging/Le
vel;Ljava/lang/String;Ljava/lang/String;Ljava/lang/String;)V
at org.apache.commons.logging.impl.Jdk14Logger.log(Jdk14Logger.java:126)
at org.apache.commons.logging.impl.Jdk14Logger.info(Jdk14Logger.java:192
at org.apache.commons.modeler.Registry.loadRegistry(Registry.java:264)
at org.apache.catalina.mbeans.MBeanUtils.createRegistry(MBeanUtils.java:
1702)
at org.apache.catalina.mbeans.MBeanUtils.<clinit>(MBeanUtils.java:163)
at org.apache.catalina.mbeans.GlobalResourcesLifecycleListener.<clinit>(
GlobalResourcesLifecycleListener.java:117)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstruct
orAccessorImpl.java:33)
at sun.reflect.InflatableConstructorAccessorImpl.newInstance(InflatableC
onstructorAccessorImpl.java:38)
at java.lang.reflect.Constructor.newInstance(Constructor.java:273)
at java.lang.Class.newInstance0(Class.java:290)
at java.lang.Class.newInstance(Class.java:249)
at org.apache.commons.digester.ObjectCreateRule.begin(ObjectCreateRule.j
ava:253)
at org.apache.commons.digester.Rule.begin(Rule.java:200)
at org.apache.commons.digester.Digester.startElement(Digester.java:1268)
at org.apache.crimson.parser.Parser2.maybeElement(Parser2.java:1452)
at org.apache.crimson.parser.Parser2.content(Parser2.java:1717)
at org.apache.crimson.parser.Parser2.maybeElement(Parser2.java:1469)
at org.apache.crimson.parser.Parser2.parseInternal(Parser2.java:500)
at org.apache.crimson.parser.Parser2.parse(Parser2.java:305)
at org.apache.crimson.parser.XMLReaderImpl.parse(XMLReaderImpl.java:433)
at org.apache.commons.digester.Digester.parse(Digester.java:1543)
at org.apache.catalina.startup.Catalina.start(Catalina.java:449)
at org.apache.catalina.startup.Catalina.execute(Catalina.java:400)
at org.apache.catalina.startup.Catalina.process(Catalina.java:180)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:30)
at sun.reflect.InflatableMethodAccessorImpl.invoke(InflatableMethodAcces
sorImpl.java:48)
at java.lang.reflect.Method.invoke(Method.java:306)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:203)
any further suggestions upon this post will be gr8ly appreciated
regards
arnab -
N95 8GB buttons or wiring problem? Pls Help!!!
Got me the weirdest problem. If anyone could help please!
For some odd reasons, the buttons 7,5,9,0 as well as my red and green button do other functions. For example pushing the 7 button would bring out 7283# 5 would bring out 5164, my red button would start playing music. Anyone encounter this problem?
Bought the phone in San Francisco and said I had a year factory warranty. However, when I called Nokia for the support, they had said my phone was a Malaysian model so they wouldn't fix it in the US.
Any help or suggestions is welcome. Thank you so much!!!I have formatting using the *3+call and did not solve the problem. I even updated to the newest firmware. So far those buttons still do other functions. i would try the *#7370# but the 7 and 0 puts out other numbers... bummer -_- someone said it's due to the internal wiring of slider phones? I appreciate everyone's input!
-
now after get my N95-1 upgraded to latest V21.0.016, i hav to on my phone without memory card insered first only can start my phone smoothly...after thst i put my memory card by way of "hotswap" into the phone...if i just on my phone with memory card in, u all know my phone will wait until 10 to 15 minutes to boot up & access menu...when press *#0000# or *#06#, the phone will not shown the details, but if i on my phone without memory card, it will show ...my 4GB memory card is no problems at all...moreover i only restore setting to my phone & all my file were saved to memory card...this indicate there is firmware system hav problem in boot up to get access to memory card...pls pls solve this serious bugi..u know my memory card always swap in & out will spoil 1t !
hi...
I understand your predicament... Its awful 2 experience such a thing.
By the way, i am also using n95 v21 and a sandisk 4gb card.
If i understand it right, after you updated your firmware, you restored the back up settings. And you also mentioned that problem only occurs when you are inserting the memory card.
It doesn't necessarily mean that your memory card is faulty. When i still have v12 and i updated it to v20, i was using a 2gb and it happened to me, so what I did was 2 copy the files stored in my memory card to computer, put back mmc to n95, format mmc and then manually copy back my files from computer to n95/mmc. And it worked for me!
Hope this works for you too.
CeS
"The best index to a person's character is how he treats people who can't do him any good, and how he treats people who can't fight back" -
N95-1 V21.0.016 CANNOT READ MEMORY CARD WITH PREVI...
After i done my upgrade for my N95-1 fr V12.0.014 to latest V21.0.016, everything seem fast & good with the formatted standard 1GB micro Sd card..but when restore phone memory setting (which were previously bac up thru latest PC Suite mode to PC), it restore very slow...nevermind coz a lot of activation key, licence key to be put into phone, after 3 hrs only successfully restored just the setting...phone auto ask for restart now...terrible nightmare happen...my phone became very very slow to respond...nevermind coz 1st time restart...after wait i think half an hr, only can move the menu smoothly...to my BIG SUPRISE ! when i off my phone & restart 2nd time...it wait even longer ...abt more than 20 minute to start the phone...after that seem like hang . WHAT IS THIS , NOKIA ! U DID NOT TEST ON RESTORE ALSO CAUSING PROBLEM TOO, PLS REALLY SOFT OUT WHY SUCH PROBLEM HAPPEN IN THIS LATEST V21 ??? WHAT FOR NOKIA ASK OUR USER TO UPGRADE ?
anybody suffering this annoying problem ? pls voice up pls....now i also don't know what to do...really sad...
-
N95 V21.0.016 UPGRADED WITH 4GB CARD - PHONE DEAD ...
IT IS WELL, VERY GOOD & FAST FOR MY N95-1 UPGRADED WITH V21.0.016 IF NO MEMORY CARD IS INSERTED. ONCE INSERTED MY SANDISK 4GB (WITH ONLY 3GB USED), IT CAUSE THE PHONE CANNOT BE STARTED....THIS IS REALLY NOT MAKE SENSE AS LATEST VERSION EVEN CAN FUNCTION PROPERPLY EVEN TO 8GB CARD ! NOKIA PLS CHECK WHY MEMORY CARD ALREADY CAUSE THIS PROBLEM! V12.0.014 IS BETTER FOR ME IF NGAGE IS NOT SUPPORTTED V12, I SWEAR I WILL NOT UPGRADE TO V21...PLS SOLVE OUT QUICKLY FOR OUR V21 USER WHO FACING THIS PROBLEM AROUND THE WORLD
i guess this is because of the applications and files already in the memorycard.
why don't you try formating the card (after copying the data elsewhere, if you need it later) and switching on the phone with the formatted card.
if it works, you can install the applications one by one back again and figure out which application is causing the problem.
please let me know if this works. -
N95-1 V21.0.016 WITH 8GB MICRO SDHC CARD ?
Any one hav used n95-1 with latest version V21.0.016 8GB micro SDHC card up to more than 50% of the card capacities? any problems of slow response or other kind of problems? Which brand is better? Sandisk or Kingston or ? pls help! thanks
18-Jun-2008 01:32 PM
psychomania wrote:
Definitely a no brainer!
I find it very odd that a sandisk class 6 card is cheaper than a sandisk class 4 card???
Of course it's odd!
I think the answer is just that prices are quickly dropping, especially on newer models, and the "class 4" prices are just "old" prices of items already in stock.
The italian online-shop site I was browsing (a reliable site, AFAIK), looking for the card, sells "class 4" for 39,49 euros and "class 6" for 35,89 euros.
And it seems they just retouched the higher price: just a couple of days ago, on the same site, "class 4" model price was about 45 euros! I think now they are trying to sell all "class 4" they have in stock, whereas they say they have no "class 6" in stock at the moment (I could just order it).
Thanks everybody for the clarifications.
Message Edited by freesailor on 18-Jun-2008 01:48 PM
Message Edited by freesailor on 18-Jun-2008 01:59 PM
Maybe you are looking for
-
[Solved] serial to usb not working - gpsbabel with garmin etrex
I'm trying to transfer some data from an old garmin etrex gps via a serial cable (Startech.com 1 Port FTDI USB to Serial RS232 Adapter Cable with COM Retention) which claims to work with linux. However, I try: $ sudo gpsbabel -i garmin -f /dev/ttyUSB
-
JFileChooser - after slecting save -- the JFC reappers
Hello, I having a problem with JFileChooser. After inputing the filename in which to be saved and slecting the save button - JFileChooser re-appears! Does anyone know why? I just want the JFileChooser to dissapear after I select Save. i'm using j2sdk
-
After updating software ipad not working
I can log in but no apps are working after updating to IOS 5
-
Changing leave request status.
Dear all expert, I am trying to customize my leave application wf (12300111) to 2 level of approval. I am facing a problem, after my first approval approved the leave request, the status in PTREQ_HEADER will change to approved. How can i reset the st
-
Why can't I write to my external hard drive?
I have a new Macbook pro, but when I plug in a USB hard drive it is "Read Only." I can find various places to change this, but they are never active for me. Anyone know what to do? Thanks!