N95-3 - really need wifi EAP-LEAP

hello all,
i have a nokia n95-3 and need to configure a wlan conecction using 802.1x EAP (LEAP) security.
i have created a new wlan and selected EAP but i can not see any EAP-LEAP plugin to configure.
type: rm-160
model: n95-3
current firmware: 20.2.011 (13-05-08)
thank you very much for any help.
jose
Message Edited by guindasoft on 29-Sep-2009 11:51 AM
Salud2, Guind@Soft
.: Haz lo que puedas, con lo que tengas, estés donde estés :.

guindasoft wrote:
hello all,
i have a nokia n95-3 and need to configure a wlan conecction using 802.1x EAP (LEAP) security.
i have created a new wlan and selected EAP but i can not see any EAP-LEAP plugin to configure.
type: rm-160
model: n95-3
current firmware: 20.2.011 (13-05-08)
thank you very much for any help.
jose
Message Edited by guindasoft on 29-Sep-2009 11:51 AM
I think that N95 may actually be one of the rare WLAN enabled Nokia phone models that doesn't support LEAP authentication method at all. It seems that you are out of luck connecting to that particular WLAN network unless authentication server on the network supports also some other EAP authentication methods e.g. PEAP, TTLS or TLS that are supported by the N95.

Similar Messages

N80 and WiFi EAP-LEAP

Hi Forum,
I have had huge problems with WiFi, hence I got it firmware upgraded to the p.t. latest fw version 4.0623.0.41 RM-92 N80 (03).
Now WiFi and Bluetooth works alot better and sure alot faster. I recommed getting latest fw !
I discovered that LEAP is supported for Wifi and since I have LEAP on the job i though I would give it a try.
Now I am the network administrator on my job, so I have 100% controll over the wireless installations etc.
I can not get the N80 to work with LEAP at all !
I get user authenticated, byt I never get an IP from DHCP.
I did debug, and the phone doesnt sent any DHCP requests etc, as clients must.
Ok - then I tell the phone to use static IP.
Still notthing happends - I get user auth ok and thats it !
I can only conclude that Nokia N80 and Cisco Systems Aironet platform doesnt work.
Are there ANYONE who has LEAP running on the N80 ??
I for sure would like to hear about the setup, so please di tell.

I am running a broadcast (public) SSID, and running on the N80 Internet Edition firmware.
I suppose I may have to accept that the N80 WIFI just does not work with EAP et al., I have debugged the EAP negotiation on the AP and the RADIUS server and everything appears normal - however the N80 will not assume an IP address nor will it pass traffic when performing link state tests from the AP (I am using a Cisco AP1220, 802.11g radio, and image c1200-k9w7-mx.123-8.JEA).
Such is life - hopefully the N95 will work...
JJ

Eap LEAP wifi standard missing in N95 ?

Hi there,
i need eap leap security standard in order to connect to office wi fi , when i started to set up the connection i cant seam to find it under EAP security settings ?
Now i had no problem settin this up on e60 e61 or even older s8 9300i ...
Now am i missing something or this is not on the N95 pls be so kind and check urse lookin forward for ure reply ...
PS ... have the latest fw my phone is sim free no branding there !
regards laz

guindasoft wrote:
hello all,
i have a nokia n95-3 and need to configure a wlan conecction using 802.1x EAP (LEAP) security.
i have created a new wlan and selected EAP but i can not see any EAP-LEAP plugin to configure.
type: rm-160
model: n95-3
current firmware: 20.2.011 (13-05-08)
thank you very much for any help.
jose
Message Edited by guindasoft on 29-Sep-2009 11:51 AM
I think that N95 may actually be one of the rare WLAN enabled Nokia phone models that doesn't support LEAP authentication method at all. It seems that you are out of luck connecting to that particular WLAN network unless authentication server on the network supports also some other EAP authentication methods e.g. PEAP, TTLS or TLS that are supported by the N95.

Wifi Syncing really needs a fix. Or at the very least some manual parameters.

After installing IOS5 , itunes 10.5 and making sure eveything works i've come across a snag like many others.
Wi-fi syncing simply doesn't work for me.
I have the option in summary , it is clicked and enabled.
I've followed the trouble shooting guide here : http://support.apple.com/kb/TS4062 a few times over.
Still my phone claims not to see the computer itunes is installed on.
On my phone , in settings - general - iTunes Wi-Fi Sync the button is greyed out and under it it says "Sync will resume when "HOUSE-03-PC-05" is available".
It is available LOL , ios stop lying to me.
I have installed a few ping apps , where pinging to the ip of said computer works fine from my phone.
I have disabled my windows firewall to be sure nothing is being blocked by it.
I checked if bonjour still works with other apps that need it. And they work.
Airvideo for example can connect to the computer that has my itunes installed just fine.
I installed "ip scanner" , it seems to discover the netbios name of the "HOUSE-03-PC-05" computer just fine.
The wireless access point I use is a D-link 2100AP, it doesn't block nor firewall anything. . Everything else wifi related I do works fine.
Itunes is running , my power cable is plugged in , and i'm not sitting at the wrong side of the desk while looking at the back of my screen.
I have even started a few tcp server programs of my own making on various ports on the pc itunes is installed on and connected to those ports using issh in telnet mode , and it works just as it's suposed to.
Something really needs fixing when it comes to the phone finding the computer that it uses for syincing.
Maybe the option to indicate the IP to try and connect to would fix it ? is it a resolve issue?
I was thinking the problem could be from uisng hyphens in my netbios names , but i really would doubt that .
Any more ideas on what more I could test for would be apreciated .
Kind Regards
Phoenixxl.

I had exactly the same problem and couldn't find the answer anywhere. However after playing a bit I found out that my computer name (i.e. Right click on "Computer" and select properties) contained a hypen. I renamed the computer to delete the hypen, restarted and now it syncs wirelessly like a charm!
Obviously something that apple overlooked which will probably right itself in the next release but should get you up and running fingers crossed!

I REALLY NEED HELP WITH MY CURVE 9300'S WIFI!

HI !
i have a blackberry curve 9300, OS5. I got it secondhand. It worked really great, but the problem started when I've done that thing within the host routing table. Though my wifi is connected, I can't use the internet. whenever I tried the BB browser and any other application (e.g. facebook, opera mini, etc.) i get a message that says 'i am not in an area that supports blah blah...' or 'unable to connect to internet please try again later'. I checked the browser under browser config and it is set to my local network provider. i changed it to hotspot browser, saved it. But whenever I go back it also goes back to my local network provider. i have tried almost EVERY troubleshooting I've read on this forums and in other forums but still no luck. The problem worsened when I did a security wipe on the emails, contacts, etc.
-APN settings are disabled
-default browser set to hotspot browser
-firewall disabled
-data services are on
Everyone said that it has nothing to do with that activation enterprise so I did not configured it after wiping.
I also tried doing a hard reboot (pulling the battery out and waiting for 5 minutes before turning it on) but it will only fix the problem for sometime and it will go back again.
Calling my network provider would just suggest to get a plan when in fact, I was able to use the device's wifi well before without any plan.
I don't want to upgrade my BB to OS6 coz it easily drains the battery of device and I cannot afford doing that because I go out a lot.
I also tried changing my sim card and network provider but wasn't successful.
I also tried deleting the name of my local network provider in the service book under options.
What do you think could be the problem? Any suggestions? I really, really, REALLY, need help.
PLEASE ! THANK YOU VERY MUCH IN ADVANCE!

Hi miochan984,
Welcome to the support community!
A supported data plan from your mobile network provider may actually be required to use the Facebook for BlackBerry smartphones application as well as the browser. I would recommend verifying with them which services they support over a Wi-Fi connection without a data plan.
Let me know if you have any other questions.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

Really need help BBM not working on wifi

ok so I've just updated my torch 9800 software and with it all of the apps, but there's the problem that my BBM wont work on wifi. why is that? I'd tried to resend the service books but there was a message about server conection problems, then I'd even tried by the BBM configuration icon in the setup menu but there was another message (imposible to configurate BBM, a temporary error was notified with the server) so I dont really know what to do... really need help this is my only comunication way with my family on the other side of the world.

On the handset, go to:
For OS5 and 4.x
Options - Advanced Options - Host Routing Table
and click Register now, and escape back to the home page.
For OS6 and higher
in options, device , advanced, host routing table, click on menu and choose register now.
Wait 2 minutes and see if registration to network happens.
Resend your service books from your carrier BIS site:
From your handheld device: http://www.blackberry.com/btsc/KB15402
Go to the Personal Email Set Up icon and log in. Then under Help!, select Service Books, then select Send service Books.
From your desktop PC: http://www.blackberry.com/btsc/KB02830
North American Carriers - scroll down to select your carrier
WorldWide Carriers - Find your carrier on the list
3. With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot. This reboot, even if you have already done this, is often needed to install the service books.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Is a device w/an ethernet connection REALLY needed to modify wifi password?

I'm not all that tech savvy. About 6 years ago my son helped us set up our wifi and router. We opted to NOT have a password as we were the only home in the area at the time and never understood the risks of unlocked despited being lectured by our son. Times have changed, a development went in where farms used to be and now we have decided to use a password. I've looked up how to do so witelessly and have accessed the screens and now what needs to be done, BUT I'm leary to do so as all the tutorials I've look at seem to suggest an ethernet connection is needed. The issue is we have no devices with an ethernet port. We use our wifi for our mobile devices, tablets, smartTV and Roku. My son now lives in another state. Is the ethernet really needed to simply add a password? Or is there another way to handle this. Thank you!
Solved!
Go to Solution.

Hi! An ethernet cable is only required to establish a connection with the router. Since you've been connected to the router wirelessly, there's no need to connect a cable connection anymore. To secure your network, follow the instructions from this link: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=22751 . Have a good one!

Ios 5 phone as your only device ? Really ? Stiil need wifi

Ok so ios 5 sposed to be pc free , but i dont have wifi but have unlimeted 3g well 450gb yes gb !! But i cant face time or down load app bigger than 20mb !!! That aint fair no backup over 3g ? Shouldnt it be our choice how much data we use ? Maybe a warning to say about data ! Thats all its my 3g not apples plz apple let me get bigger apps an face time

That just makes no sense. If you want WiFi for whatever devices you have, you get internet access. I have an AppleTV, a PS3, a couple of phones, a scale (yup, the kind you weigh yourself with) that use WiFi. And, of course an iPad. Even if I didn't have a computer, I'd still need WiFi.
And, at this moment, I'm sitting in a cafe using WiFi. I don't have a computer. I'm using my iPad. As I said, access to WiFi has nothing to do with being "PC free".

E6-00 and Belle update : Cannot use Wifi and LEAP ...

Upgraded the E6-00 yesterday. First issues arise and even after a full reset, it still does not work.
- Wifi connection using LEAP authentication
Network is found, popup to enter username and password, all is good. Except the phone keep trying to connect while I type the password and each time, it re-ask the username. In short I cannot use connect at all as I don't have time to enter both username and password before it loop.... No more wifi connection possible as it use this LEAP authentication. Any way to increase the connection retry timeout ?
- IMAP folder not found
Same config as under Anna, but under Belle, it does not find any folder for IMAP account (and yes, the mail root folder is right), refreshing the folder list, just do nothing.
- MAPS
Say that it's empty and need maps. Give few options:
   * use OVI on the PC : OVI doesn't find MAP on the phone
   * use wifi to download map : .... if wifi would work, why not
Anybody else got the same issue ? Or found solution ?
L.\
Solved!
Go to Solution.

Upgraded the E6-00 yesterday. First issues arise and even after a full reset, it still does not work.
- Wifi connection using LEAP authentication
Network is found, popup to enter username and password, all is good. Except the phone keep trying to connect while I type the password and each time, it re-ask the username. In short I cannot use connect at all as I don't have time to enter both username and password before it loop.... No more wifi connection possible as it use this LEAP authentication. Any way to increase the connection retry timeout ?
Ok try to delete your apn, reset the device and resintall the OS. Don't restore any backup ans configure the WLAN apn: settings> connectivity> settings>destinations. Into the WLAN settings go to WI-fi security settings> in the fifrst field select EAP> in the second field EAP plugin settings > select EAP-LEAP.
This way the apn will work again
- IMAP folder not found
Same config as under Anna, but under Belle, it does not find any folder for IMAP account (and yes, the mail root folder is right), refreshing the folder list, just do nothing.
Please delete your mailboxes and configure them as you want. To create a IMAP access mailbox , for example Nokia Mail (outside of Messaging server) select Other. Put you credentials and choose Standard. You will see into Settings> your mailbox > sync content > Folder subscriptions> choose which folder to sync and it's done
- MAPS
Say that it's empty and need maps. Give few options:
   * use OVI on the PC : OVI doesn't find MAP on the phone
   * use wifi to download map : .... if wifi would work, why not
Anybody else got the same issue ? Or found solution ?
Please delete on mass memory the folder Cities and the file Qf, then open Maps and close the application. Verify that the folder Cities and the file Qf are again in E. Connect your device to Nokia Suite and redownload the cartography.

Is EAP-LEAP plug-in supported in Nokia X6 version ...

For those who has upgraded Nokia X6 16GB to V20.0.005 NAM version, does it still have the EAP-LEAP plug-in available. And, does LEAP still work?
LEAP is a little bit out of date and not included in WPA2. I see the reasoning to drop its support. But I just need it.
The V20.0.005version has some features I would really like but LEAP is a must for me. Given that downgrade is not formally supported, a little bit nervous to try it. Some seems to encounter problem as reported in this post.
Share your experience please. Thanks very much!

Answer my own question. Nokia support said LEAP is still available. It is true. I upgraded to V 20.2.005 and it still have EAP-LEAP and working fine.

EAP-LEAP Module for Windows Vista & 7?

I’m trying to understand the 802.1X clients/modules Cisco offers. I found the Cisco Secure Services Client and the EAP-FAST Module for Win Vista/7. But where do I download or learn more about the EAP-LEAP Module for Win Vista/7?

Well you can try this:
http://blogs.msdn.com/b/eapteam/archive/2008/10/17/how-do-i-install-cisco-eap-fast-on-my-computer.aspx
http://blogs.msdn.com/b/eapteam/archive/2008/10/17/how-can-i-download-the-ecp-methods-from-the-web.aspx
however I dont know if it is needed, but on my computer I already have LEAP EAPFAST and cisco PEAP
From intel, EAP-SIM, EAP-TTLS and EAP-AKA
Im running Windows 7 ultimate
I can see these options on WZC when I am setting up the security options on the profile.
I recently downloaded the wireless drivers for my Intel 3945ABG wireless card. So I cant really explain if there were since the begining or thru a windows update or maybe due to the manually updated Intel drivers...
Hope it helps you

E90 eap-leap connectivity, as usual not working...

Sorry folks, here we go again.... I have already made some search in the forum about the topic and also tried them accordingly to no avail. First try, general error, second try it will crash (screen will blank out and restart, what a graceful exit!!!) Well I cant count how many restart I made and Im a little bit tired, maybe I need some help. =)
Anyway here's my settings : (this setting is working perfectly on windows XP, so I assume its a handphone or handphone config issue)
Model : E90
Firmware : 07.24.0.3
Name : CompanyRoam
Data Bearer : Wireless LAN
WLan Net name : CompanyRoam
Network Status : Public
WLan Net. Mode : Infrastructure
WLan Security Mode : 802.1x
Wlan Security Settings :
WPA/WPA2 : EAP
EAP plug-in settings : EAP-LEAP (Disabled everything but this)
Username : *username* (also tried *username*\*domain*)
Prompt Password : No (tried yes then no, as said in some forum)
Password : myDomainPassword
Others : ip address using dhcp

After more research on Eap-Leap connectivity, I found someone that can connect to our corporate wifi but using a Nokia E60.
My settings were the same as his E60, i even ask him to place his username and password to my Nokia E90 and still it crashes. So finally conluded this is a firmware problem.
It is so embarrasing the same NOKIA manufacturer, even the same E-SERIES and does not work. Hopefully by next firrware this should work.
So for E90 users out there, no eap-leap connectivity as of my current firmware. I will continue to update this thread as new firmware arrives.

I need to connect my iPad to a projector and USB ports. What do I need to do this and where can I get the suitable fittings? I really need to have more than one USB connection port. Help

I need to connect my iPad to a projector and have USB ports. What do I need to do this and where can I get the suitable fittings? I really need to have more than one USB connection port. Help

You can connect via a cable or wireless using an Apple TV.
http://ipad.about.com/od/iPad_Guide/a/How-To-Connect-Your-Ipad-To-Your-Tv.htm
Connect an iPad to a Television or Projector
http://www.everymac.com/systems/apple/ipad/ipad-faq/how-to-connect-ipad-to-tv-te levision-projector.html
Connecting iPad iPhone or iPod to TV or Projector
http://www.disabled-world.com/assistivedevices/computer/ipad-tv.php
iPad Accessories: Connections for a TV or Projector
http://www.dummies.com/how-to/content/ipad-accessories-connections-for-a-tv-or-p rojector.html
You may be interested in AirPlay on the Apple TV:
http://www.apple.com/airplay/
Alternately, there are Apple Digital AV Adapters for hardwired connections:
http://support.apple.com/kb/ht4108
If your location does’t have wifi to use with the Apple TV, use a portable router.
Portable routers http://compnetworking.about.com/od/routers/tp/travel_routers.htm
 Cheers, Tom

Restrictions Really needs improvement for Business use

Hi
We have written an app and are replacing our industry standard barcode scanning devices with over 100 iPod Touches worldwide using a third party barcode sled accessory. This is much cheaper (Around $800 vs $1500) and offers a much richer and less confusing user interface to the end-user. However our end-users are often low paid seasonal workers employed by our clients, so when it comes to the restriction settings in iOS we try to lock the devices down as much as possible.
I think more and more people are treating the iPod/iPhone/iPad in commerical environments and so the ability to secure and maintain these devices really needs to be improved. Our situation aside you can use your iPhone as a point of sale with a credit card swipe, if you have a retail chain with several of these devices for use by employees you don't want them to be messing around on them or making choices that you don't want them to purposfully or accidently.
For instance:
iOS6 upgrade seems to download automatically and prompt the user if they want to install. There is no way to turn updates off, and not even a password is required to do it. In my scenario if someone gets the upgrade push and then clicks ok they then can't work for 30 minutes, not good if there is a long line of people waiting to be served.
WiFi/VPN connections can be changed
Passcode lock can be turned on/off/changed
Date/Time / Keyboard / International / Accessibility settings can all be played with
Weather app always available
Stocks app always available
Maps can be used (location can be disabled at least!)
etc..
If I (as a developer) tell our deployment manager to tell our client's manager to tell their scanning manager to tell their temporary workers to not mess around with things like the above....someones not going to listen, and our IT department is just going to have to check each device and clean up.
I know that apple's portable devices are aimed more at consumers, but I personlly think it's about time that we have some more attention to more business scenarios.
I don't want to come accross negative so i'll finish by saying that a lot of the restrictions in place are very useful. Being able to disable the store, iTunes and safari are very big wins, without those we wouldn't have switched to iOS devices.
Anyone else have a similar need for more administrative ability?
Thanks for reading.

One of these might be good for a POS (assuming you need touch screen), but those are terrible for graphic artists to use. All-in-ones are to be put bluntly, over-priced pieces of junk with crappy power supplies and worthless integrated video cards. They will run too hot most likely and need maintenance more often than larger well-ventilated desktop towers. Your graphic artists staff will hate the small low resolution monitors as well as the lack of decent GPU acceleration. The only good thing about them is the small form factor, a sacrifice well worth looking past IMHO.
Graphic artists should be using high-end monitors, IPS panels for accurate colors and high resolution displays of 2560x1600 pixels. I strongly recommend looking at Dell's Ultra Sharp models (particularly the 30"). If you end up getting three Dell Ultra Sharps then you might as well get the whole system from them as well and develop some sort of professional relationship and support system like most businesses.
*The monitor should be the most expensive component by far and it is the most important for work productivity, do not skimp out here, you run a graphic design firm after all!
Look for reasonably priced desktops with 4-8GB RAM, Intel or AMD quad core processors. Stay away from discrete graphics, Photoshop uses GPU acceleration found on higher end video cards and it is useful. Larger hard drives perform better than smaller ones because of areal density, so buy larger hard drives than needed (1-2TB drives with 500GB or larger platters) and run them in RAID1 for redundancy, because I doubt you have a storage area network.

My ipod touch got stolen and i didnt download the tracker... i really need it back it has all my information on it.. What should i do? Can i download it on another ipod to find it?

My ipod touch got stolen and i didnt download the trackking app i really need it back it has all my music and information on it.. What should i do? Can i use another ipod to download the app and find it on someone elses? Please help

No app is required.
- If you previously turned on FIndMyiPod on the iPod in Settings>iCloud and wifi is on and connected go to iCloud: Find My iPhone, sign in and go to FIndMyiPhone. If the iPod has been restored it will never show up.
- You can also wipe/erase the iPod and have the iPod play a sound via iCloud.
- If not shown, then you will have to use the old fashioned way, like if you lost a wallet or purse.
- Change the passwords for all accounts used on the iPod and report to police
- There is no way to prevent someone from restoring the iPod (it erases it) using it.
- Apple will do nothing without a court order
Reporting a lost or stolen Apple product
- iOS: How to find the serial number, IMEI, MEID, CDN, and ICCID number

N95-3 - really need wifi EAP-LEAP

Similar Messages

Maybe you are looking for