N95 Display/Software error?

My N95 recently started behaving very strange just 1 month after warranty ran out (typical)
The Phone boots up nicely but then after a short while the display starts to "flicker" or display snow on the screen.
If you push a button the display lights up with a grey background and after ~5 seconds I can see the background image which then dissappears again - into the grey color.
At first I thought, well this could just be a display replacement needed since the display didn't work on another n95 either. I ordered a new one, replaced it - same thing happens! so it is not the display itself unless the phone somehow already damaged the new one.
One note, after you push a button and the display turns grey the "side buttons" (play/camera) blinks blue within seconds of each other - could this be an error code of some kind?
I've already checked the humidity label inside and the phone has not ever been dropped in water of any kind, the error occured while web browsing. I've also updated to newest software release. Previously I had QT installed also.
Any thoughts on this? .. thinking other brand next time since i really think a phone should last more than 1 month after warranty.

Seems like you've messed up the display electronics. You should've taken it to the experts (Nokia Care) instead of doing it yourself. It will cost you dear anyway. Better take it to a Nokia Care Point. They will be able to fix it. I don't think it's a software error.
Good luck
Cheers,
DeepestBlue
5800 XpressMusic (Rock Stable) | N73 Music Edition (Never Say Die) | 1108 (Old and faithful)
If you find any post useful, click on the Green "Kudos" Button on the left to say Thank You...

Similar Messages

  • HT4623 Unable to update to iOS 7.0. Error displayed "Software Update Unavailable"

    I have an iPhone 4. I was able to download iOS 7 but it did not install. Now when I try to install it and error is displayed "Software Update Unavailable"

    Have you tried to update via iTunes or via Wifi?  Here is the article on how to do both - http://support.apple.com/kb/ht4623
    Tell us what it's telling you when you try if you are having issues.
    Some common things to try if you are having issues doing it over wifi:
    1) Turn on Airplane Mode in Settings.
    2) Turn the iPhone off completely for about 2 minutes by holding the power button and sliding the red bar.
    3) Turn the iPhone back on and turn off Airplane mode from Step #1. Try to update again.
    4) Go to Settings > General > Reset > Reset Network Settings. Then reconnect to your Wifi and try to update again.
    If you are getting an error about space, you can delete some apps or information to free up space on your iPhone (You can view what's taking up space in Settings > General > Usage) or you can update via iTunes on the computer. http://support.apple.com/kb/ht4623

  • BlackBerry Desktop Software displays the error "Caught _com_error exception. Description(): (null): Error(): -2147319779 (0x8002801D). ErrorMessage(): Library not registered.:Source(): (null)." when attempting to synchronize organizer data

    BlackBerry Desktop Software displays the error "Caught _com_error exception. Description(): (null): Error(): -2147319779 (0x8002801D). ErrorMessage(): Library not registered.ource(): (null)." when attempting to synchronize organizer data.Can someone help me with this?  

    Tried clean wipe and reinstall. Immediately after reinstall of DM, in setting up my 9900 "for the first time", I received the following error message...
    "Either there is no default email client or the current mail client cannot fulfill the messaging request. Please open Microsoft Outlook and set it as the default mail client."
    I opened Outlook 2013 and checked that it was the default mail client. It was already.
    After going in and clicking to confirm default email client, I was allowed to proceed to configure organizer sync settings. I configured memo only (one way from device). I then received the same error message that I was receiving (per my original post in the last message). I've previously tried configuring only one type of organizer sync and not one of them completed a successful sync, so it can't be a bad entry in the calendar or contacts. I also tried deleting CICAL entries for all of email addresses other than my primary one. No difference. Also, prior to setup and sync, I confirmed that my 9900 was not on wireless sync.
    I was hoping that this was an old issue and I could use one of the old work-arounds, so if anyone has any ideas for something else to try, please let me know.
    In the mean time, I  have to assume that it's something that's changed with Outlook 2013 (particularly given the new error message I reported above. I hope that someone at RIM is aware of these error messages and is working on a compatibility fix for Office 2013.
    Thanks in advance,
    Sheldon
    Twitter: @sheldonbk
    Twitter: @sheldonbk

  • HT1766 my backup is failling to restore and displays an error message: backup either corrupt or not compatible with the device. This happened after updating to the latest software IOS7

    My backup is failling to restore and displays an error message: backup either corrupt or not compatible with the device. This happened after updating to the latest software IOS7

    I have the same issue and I KNOW my backup IS good. What happen is when you try to restore your phone apple says something like can I check for new updates and if you choose no, it just takes you back to the restore screen and a loop from then on.  If you dont update from you phone then when you back up you will have the 5.0.1 back up and then when you update to 5.1.1 and then try to restore the backup from 5.0.1 it say it EITHER corrupt or incompatible.. It is incompatible and its hard as **** to restore back to 5.0.1. I followed the restore to a T and still getting errors. I lost all text history and have to reset up email. All just because I wanted a 1.2 Gigs of "other" space back.

  • Huey Pro calibrator- error message  display measurement Error

    i am using this huey pro calibration.. it had been a year without problem... but now i am trying to calibrate my apple cinema display LCD 30 inch it keep saying error message- display measurement error.. and huey support never answer my e-mail. any idea? how can i fix it.. i did re install software many times but same thing happen.. so right now i can;t calibrate my monitor.. any help please

    >a nice NVidia card... Please help Adobe!
    1a - what is the model nVidia card, and what is your driver version?
    1b - for instance, I have a GTX 285 and driver 296.10
    2a - aside from the occassional Adobe employee, this is a user to user forum, not Adobe suport
    2b - how to contact Adobe...
    Adobe contact information
    http://www.adobe.com/support/contact
    In the US - Adobe General support 800-833-6687 M-F 5am-7pm Pacific
    In the US - Adobe Install Problems 800-642-3623
    In the US - Adobe Activation 866-772-3623 Open 24/7

  • Internal Software error PGC  for encore CS3 !!! solved  !!!

    Almost everybody here knows the next error:
    PGC "timeline name" has an error at xx:xx:xx:xy internal software error : %0, line timeline name - PGCINFO: name= timeline name, ref=BPGC, time=xx:xx:xx:xy
    Where the y in time stands for the length of the timeline minus 2 frames. The BPGC error can also be FPGC or DPGC dependant on how many menu's there are in the project.
    It kept me awake for weeks and after reading this forum several times and comparing encore CS3 with encore 2.0 filenames I found the solution.
    This Error is a bug in encore witch has nothing to do with blank filename spots and sonic coding or codecs or planning your workflow with a pencil but pure with the combination Adobe Premiere Pro CS3 and Encore CS3.
    This is what generates the problem:
    In Adobe Premiere Pro CS3 you build project with video, sound and chapters. Then you export the project via the Media Encoder not Multplexed.
    Premiere CS3 then creates the following files:
    filename.M2V (video file mpg)
    filename.AC3 (audio file ac3)
    filename.M2V.XMPSES (an adobe file with preview info and chapter pointers)
    filname.XMP (??)
    It is the .M2V.XMPSES file witch creates the PGC error. If you use the MULTIPLEX DVD option then ADOBE will not create the .M2V.XMPSES file so there will not be an error. This trick mentioned by ADOBE and many others is just to go around the bug instead of solving it. Also with multiplex you have just one sound track. I use two sound tracks like 5.1 and a 2.0 track witch you can choose in a menu.
    Some people say it is the blank spots. Also not true. They have probably just erased the blank spots of the M2V file and forgot the .M2V.XMPSES file.
    When you just delete the .M2V.XMPSES file and then open the M2V and AC3 file in Encore as a new asset, make a timeline and menu's and the project will built and burn. Only if you delete this .M2V.XMPSES file Encore takes a longer time to import the M2V file and will be without the chapter points.
    Almost everything else will work like menu with sound and even a movie background (use M2V files). Only the motion buttons in a menu still wont work unless you use a black background !?!. Haven't figured this out yet. Only solution for this is use Encore 2.0. In this older version also the motion buttons will work without error's (everything else also so why buy CS3??)
    Here is what you must do create a DVD without errors:
    -Create a project in Premiere Pro, even with chapters.
    -Write down all chapter points (minutes:seconds:frames)
    -Create two new unique maps in explorer for example D:DVD1 and D:DVD2
    -Export in Premiere with Media Encoder without the Multiplex:DVD but with NON to the D:DVD1 map
    -Copy from D:DVD1 only the M2V and AC3 files to D:DVD2
    -Start up Encore DVD CS3 or 2.0
    -Create a new unique project in Encore for example "DVD" and save this in the map D:DVD2\
    -Then use Save-as (under file) and pinpoint to D:DVD2\dvd to be sure that all Encore's files are placed in this folder.
    -Select M2V file and make new timeline.
    -Make chapter points (you wrote down the points, did you?)
    -Create menu's, even with sound (AC3) and movie background (M2V)
    -Then render project if you have used a video for menu background
    -Finally Built and burnnnnnn!!
    -If you like to use motion buttons in a menu then use Encore 2.0
    I have double checked my work flow and it really works. I have built a project and burned with success Then I deleted the timeline and the M2V file. Copied the .M2V.XMPSES file in the used folder. Re loaded the M2V file in encore (this time much faster! and with chapter points). Tried to built and burn and back was the error. Also this happened in in Encore 2.0!!
    Hope that this will solve the PGC error once and for all !!!
    Marcel W
    system:
    acer aspire AMD 64 3800+
    2 GB
    250 GB hard drive for system
    750 GB hard drive for movie
    software Adobe Encore 3.0.1.008, Premiere PRO 3.2.0, Photoshop CS3 10.0, All upgraded
    NERO 7
    No Internet

    > Where the y in time stands for the length of the timeline minus 2 frames.
    This can actually vary, and so far at least, I don't think we've seen a pattern as to type of pgc error based on how many frames from the end it reports.
    > The BPGC error can also be FPGC or DPGC dependant on how many menu's there are in the project.
    Number of menus is not relevant; the iteration of the first letter is more related to subsequent occurrences of the error. In my current tests it did not always update; they may have been too similar.
    > This is what generates the problem...
    Well, the problem does not occur every time you do what you describe, any more than it occurs every time spaces are left in the file names. What you have is, as some other suggestions, a workaround. Thats not bad, and I wonder if you are onto something as to what is contributing to the problem.
    So, on to the interesting part whether the xmpses file, or at least what Encore is doing with it, is contributing something. I took an old test project that throws the PGC error and did some experiments.
    Background. I am a user who does get the pgc errors regularly, but not always. Creative Suite Production Premium, with PPro CS3 3.2.0 (374) and Encore 3.0.1.008. Pentium 4 2.8GHz 2G RAM, XP SP3, Multiple drives, Nvidia GEforce4 MX440 i.e. an older system. I have lots of stuff loaded and running, including virus protection and firewall, so there are any number of potential conflicts. But I get no crashes, and only one problem other than the pgc. (PPro and Encore monitor windows do this diagonal thing I suspect the display card, but the drivers are up to date. Maxing and then back to fit fixes it.)
    If you want to attempt to replicate my studies, here is a link to my problem clip and the first Encore project I describe.
    http://www.videoandcomputer.com/test/pgc_test.htm
    This project involves a very short AVI export from PPro CS3 - just over 8 seconds - called pgcbad_clip1.avi. Just to answer any question, the source is dv camera capture, and the source and avi export I use are dv avi type 2. There were no effects added on the timeline.
    Test 1: Create a project in Encore CS3. Use the sunset menu and delete all the buttons except "play all." Import the avi as a timeline. Set the timeline end action as "return to last menu" and set the button link to the timeline. Auto transcode. (Project settings are 8mbps max and a3c.) Check project shows okay; there is never a problem with that. Build to a DVD folder in a new folder. This project throws the pgc error.
    Test 2: Now create a new Encore project in a new folder. Use the same process, except import as timeline the m2v and a3c files from the first run. (I.e. if the clip is pgcbad_clip1.avi, in the test1 project folders, there is a folder called pgcbad_clip1.avi that has 6 files.) Note that in the folder they are imported from is an xmpses file from the first project's encore transcode. The build again fails with the pgc error - same frame, etc, but I really think the frame number doesn't matter.
    Test 3: Now create another new Encore project in a new folder. Use same process, but before importing the m2v and a3c as timeline, delete the xmpses file. Drumroll...... Build succeeds!
    Go figure.
    This is not the repeatable bug option weve been looking for, but based on a clip that always fails, it does demonstrate the odd event of deleting the xmpses file as a workaround. I wonder if that will give adobe something to work with.
    Can anyone else get my clip to work/not work in a straight project?
    Test 4: Just to answer the question since the avi file fails here, will the elemental option succeed? I exported elemental m2v and wav from PPro, used the same project process, and transcoded the wav. That build also works! I have seen this work both ways. I have had projects where the elemental failed, and an avi export worked. I do believe the elemental options work more consistently. But my project that I completed yesterday used all avi exports, animated buttons in the submenu, - no pgc error.

  • I have Acrobat 9.5 and when I try to create pdf from scanner, it displays an error "Adobe acrobat has stopped working". Is there any way I can use this functionality?

    I have Acrobat 9.5 and when I try to create>pdf from scanner, it displays an error "Adobe acrobat has stopped working". Is there any way I can use this functionality?

    Provide you have Acrobat 9 installed in an OS for which Acrobat 9 is compatible then you can use the functionality.
    As well, you need a scanner connected, powered up, and the software installed. Acrobat 9 "prefers" TWAIN drivers.
    Always visit the scanner vendor's site and download - install the latest greatest software.
    n.b., The Acrobat 9.x product family passed into "End of Support" mid-year 2013.
    As well the Acrobat 9.x product family is not compatible with contemporary OSs.
    Be well...

  • Internal Software error

    Hi, 
    When I compile my fpga target vi i got an internal software error shown in the attached picture.
    The program I'm working on is somehow complicated and the target file size is about 801KB and I also used 15 target-scoped FIFOs to transfer data within the target. I've also attached the log file. Does anyone know what caused this problem? Thanks in advance.
    Attachments:
    Untitled.png ‏40 KB
    lvlog2011-10-06-13-05-10.txt ‏4 KB

    It is an internal error generated by the application. I think the disc is still ok since the application is still preparing the data for burning to the disc and the actual burning has not yet started. Try running the program again and see if the error is still the same. If it displays a constant error every time you try burning the project, it is either the application can’t handle the size of the data that is going to be burned or there is an error in your system.
    Run a disk check on your computer to see if there is any error that is preventing the application from working properly.
    Right click on drive C and then select Properties.
    Click Tools tab.
    Click Check Now button.
    Check Automatically fix file system errors and then click Start.
    If no error was found try launching the application again. If it’s the same, use other video editing application where you can burn a video also.
    http://www.techyv.com/

  • "My Music" app .. song name displayed in error

    Hi,
    I have a C1-01. I have stored some mp3s on the memory card, and I checked with an ID3 editor on my PC, they have their ID3 tags correct. But in the "My Music" app on the phone, when I go to "All Songs", many songs have their name displayed in error (they have extra information that I deleted from their ID3 tag). Eg: I have changed the "title" field of a song to say "Welcome", but in the song list, it is displayed as "Welcome - mp3albums.net". I checked with the ID3 editor software on my computer, the song has just "Welcome" for its title field. The music player on the phone is picking up the extra information from I don't know where. I updated the music library on the phone, it doesn't help. Switched off the phone, removed the battery, waited for a few minutes, switched on, same problem. Deleted temp files on the memory card, and the .trash folder on the card, same problem.  Any ideas?
    Also, is it possible to change the font size in the music player to extra small font?
    (My phone has the latest software update, version 5.50)
    Thanks.

    There are several versions of ID3, did you change ID3v1? or V2? what editor do you use anyway? I've found mp3tag to always be correct
    If you find my post helpful please click the green star on the left under the avatar. Thanks.

  • Internal Software Error: .\Vobulator\MuxPlanner\AudioPackPlanner.cpp, Line 530

    I am trying to make a movie and burn it to a disk for school but I keep getting that error (Internal Software Error: .\Vobulator\MuxPlanner\AudioPackPlanner.cpp, Line 530)  It occures after about 5 or 10 minutes of transcoding.  The original file was a mkv file format with a dts audio and a avs video track.
    Here is the detail of the video.
    Format                           : Matroska
    Format version                   : Version 2
    File size                        : 6.56 GiB
    Duration                         : 2h 10mn
    Overall bit rate                 : 7 197 Kbps
    Encoded date                     : UTC 2011-10-26 03:46:55
    Writing application              : mkvmerge v4.8.0 ('I Got The...') built on May 24 2011 03:12:58
    Writing library                  : libebml v1.2.0 + libmatroska v1.1.0
    Video
    ID                               : 1
    Format                           : AVC
    Format/Info                      : Advanced Video Codec
    Format profile                   : [email protected]
    Format settings, CABAC           : Yes
    Format settings, ReFrames        : 5 frames
    Muxing mode                      : Header stripping
    Codec ID                         : V_MPEG4/ISO/AVC
    Duration                         : 2h 10mn
    Bit rate                         : 5 689 Kbps
    Width                            : 1 280 pixels
    Height                           : 528 pixels
    Display aspect ratio             : 2.40:1
    Frame rate                       : 23.976 fps
    Color space                      : YUV
    Chroma subsampling               : 4:2:0
    Bit depth                        : 8 bits
    Scan type                        : Progressive
    Bits/(Pixel*Frame)               : 0.351
    Stream size                      : 5.05 GiB (77%)
    Writing library                  : x264 core 119 r2106 07efeb4
    Encoding settings                : cabac=1 / ref=5 / deblock=1:0:0 / analyse=0x3:0x133 / me=umh / subme=7 / psy=1 / psy_rd=1.00:0.00 / mixed_ref=1 / me_range=16 / chroma_me=1 / trellis=1 / 8x8dct=1 / cqm=0 / deadzone=21,11 / fast_pskip=0 / chroma_qp_offset=-2 / threads=12 / sliced_threads=0 / nr=0 / decimate=1 / interlaced=0 / bluray_compat=0 / constrained_intra=0 / bframes=3 / b_pyramid=2 / b_adapt=2 / b_bias=0 / direct=3 / weightb=1 / open_gop=0 / weightp=2 / keyint=250 / keyint_min=23 / scenecut=40 / intra_refresh=0 / rc_lookahead=50 / rc=2pass / mbtree=1 / bitrate=5689 / ratetol=1.0 / qcomp=0.60 / qpmin=0 / qpmax=69 / qpstep=4 / cplxblur=20.0 / qblur=0.5 / ip_ratio=1.40 / aq=1:1.00
    Language                         : English
    Audio
    ID                               : 2
    Format                           : DTS
    Format/Info                      : Digital Theater Systems
    Muxing mode                      : Header stripping
    Codec ID                         : A_DTS
    Duration                         : 2h 10mn
    Bit rate mode                    : Constant
    Bit rate                         : 1 510 Kbps
    Channel(s)                       : 6 channels
    Channel positions                : Front: L C R, Side: L R, LFE
    Sampling rate                    : 48.0 KHz
    Bit depth                        : 24 bits
    Compression mode                 : Lossy
    Stream size                      : 1.38 GiB (21%)
    Language                         : English
    Knowing that Encore does not support mkv I demuxed the mkv taking out the video track into a .h264 file using mkvextract.  I then muxed it into a mp4 without the audio using mp4box then dragged it into encore without any problems.  For the audio, I just demuxed it out into a dts and dragged that in as well.  I then created a new timeline and dragged each peice of media into there corresponding sections on the time line.  I tried to play the video but there was no audio.  I treid to import the dts and got a warning saying something like, "DTS is supported in this version of Encore (CS5) but just not in preview.  When I burn it to the disk there will be no problems"  So I just went ahead and tried to build the video into a dvd folder for a dual layer disk.
    The setting I have for the DVD is default except I changed the bitrate to 9.4mbps.  That's the only thing I changed.  (I used NTSC)
    I played the audio using an external player to see if it plays and it did.  When I check to see if there is any problems with the build it only says something about start remote and end action.  I have never set them before so I don't think that should matter.
    I have Encore installed on my secondary drive (Not C: which is windows) and I treid to create the DVD Folder on that drive.  When I got this problem I just thought it was that it could not create the files on the drive because the program isn't running off that drive which it should be, I treid to create the DVD Folder on the C: drive and I still revieve the same error.
    Does anyone know how I can get past this?  I need this to be done by tomorrow for school in the morning.

    Hi Stan and thank you for your concern, I was (I am) getting that in a timeline. and also a kind of general error when I was trying to build ether a folder or an image. I had made a copie of the project for me to delete all menus I also  change all "end actions" who were on "stop" configuration but still my problem was there. In this project in encore two things I did witch may be the coz ot the problem?
    -first when changing the menu styls and edition with Ps (maybe I did some thing wrong there?) and
    -second when changing throught encore the markers on my principal time line witch maybe a did in a wrong way.
    whatsoever thank you and sorry that I took a long time to answer, regarding my english writting you allready undertand that it is not my language. In addition I'm not a professional in editing but I'm still learning. I think it will be quiker for me to do the project again till the start on encore even if for me it wood be good for  to know where the problem came from for me not to do it again.
    Thanks a lot best regard
    Fabian

  • Isntalling software error message for location

    Hi all
    I have been Trying to install  Illustartor CS2 and at the install its displaying a Error message "cannot install to the disk (mac HD or Drive that comes with install) The contents of these disks cannot be changed, i have done a disk repair to ensure nothing is wrong. My macbook air is only 2 weeks old. I have the latest model. Is this a permissions issue or actually something wrong with my hard drive? Can someone shed any light on this issue? The pop up box with the two hard drives available to install this software on has an orange excalmation mark across each hardrive location as if it is blocking it for being used as a install location.

    do i need to return this to where i purchased from under warranty or even take into apple?

  • In adobe Encore "internal software error"

    If you try to create a DVD image in adobe encore,
    It is not possible to create is displayed: "Volumes / Builds / Amawat / Main / XcodeProjects / AuthorCore / / / Sonic / DVDCreator / FormatL ib / Vobulator / BlockPlanner.cpp, line 217 internal software error...." He said.
    Those of other projects can be created without any problems.
    Please tell us the cause.
    Machine specs
    iMac (2013)
    OS: 10.9.3
    Memory: 16GB
    Adobe Version: CS6
    Since it has been translated using the "Google Translate" in this sentence,
    There is a possibility that there is a portion that is disturbed, such as some grammar.
    Please note.

    This links may help
    http://forums.adobe.com/thread/1309029 http://docs.roxio.com/patches/pxengine4_18_16a.zip
    http://corel.force.com/roxio/articles/en_US/Master_Article/000012592-PX-Engine-Description -and-Download

  • HT201302 The laptop I was using to upload photos from my iphone is no longer good and I want to use my desktop instead but it is displaying an error that the iphone has no photos in it. How do I start using my desktop to upload my photos from my iphone5?

    The laptop I was using to upload photos from my iphone is no longer good and I want to use my desktop instead but it is displaying an error that the iphone has no photos in it. How do I start using my desktop to upload my photos from my iphone5, is there any software I need to download?

    Photos on the phone in the DCIM folder are those located in the camera roll. Photos that are synced to the phone from the computer cannot be accessed in this manner. They are synced and the only way to manage them is to connect the phone, go to the photos tab and un-select the folders you want to remove or go into the folder photos are located in and remove the photos you no longer want to sync. Then sync the phone and the photos will be removed.

  • ICI - How to display custom error messages in SAP CRM

    Hello,
    we are working on a custom Contact Center which interfaces with SAP CRM Version 7 with Enhancement Package over ICI.
    The basic call functions like accepting, hanging up, holding and retrieving are fully implemented and are working already.
    Our goal is to display error messages in the CRM so that clients know there is something wrong, for example why he can't be log in successfully (e.g. the telephony server isn't reachable).
    We already found the ICI Documentation file which provides us the CRM SOAP error codes and tried to send SOAP Fault messages, but never got
    them to screen.
    Please find an attached example screenshot what we mean exactly, reproduced by trying to make a call with CRM user while BCM CDT isn't
    running in the background.
    Regarding to this topic we've the following questions:
    - Is it possible to display custom error messages on the CRM or is this functionality limited to SAP?
    - Could you provide us some further information on how to use this feature exactly (implementation details?) and how the SOAP XML should look like to get it work?
    Thank you in advance!
    Best regards
    René Holy

    NewUser7 wrote:
    Please correct me if I am wrong
    I need to create an entity adapter and attach an error handler with the adapter? or can i handle that in the event handler itself. I coulnt find any api for handling errorsYou can do it both ways but since we are talking about event handler now, then in 9.x you need to extend com.thortech.xl.client.events.tcBaseEvent class for creating a event handler. In tcBaseEvent class there are various flavors of handleError method. So use that as per my note earlier and you should be good.
    HTH

  • Display Custom Error Message in OIM 11g

    Hi,
    I'm trying to display an error message from a validation event handler but seems that am missing something. When the "oracle.iam.platform.kernel.ValidationFailedException" is thrown from a validation handler an error message is displayed: "An error occurred". If an error code is provided (see code below) then the message looks like: "An error occurred. The corresponding error code is ERR-0001". I guess that some resource bungle with corresponding messages should be provided.
    the code used:
    package test;
    public class UserGeneralValidationHandler implements oracle.iam.platform.kernel.spi.ValidationHandler
    @Override
    public void validate(long processId, long eventId, Orchestration orchestration)
                   throws ValidationException
    String errorCode = "ERR-0001";
    String message = "Simple validation message.";
    ValidationFailedException ex = new ValidationFailedException(message);
    ex.setProcessID(processId);
    ex.setErrorCode(errorCode);
    throw ex;
    Q:
    1.What is missing for complete solution?
    2.What is the algorithm that used by OIM to find default or non default resource bundle?
    3.How to change out-of-box validation messages? For a sample "The organization ABC does not exist." message is shown if non existing organization is provided during user creation and I'd like to have a different one.
    Regards
    Serge

    rename OIMUI.jar  to OIMUI.zip
    find logging_en and loggin.properties.
    Modify the "IAM-2050512" error message with your custom message
    Find Agent and agent_en.properties.
    Find Note[ERROR_SUBMITTING_REQUEST].text.  Modify the message. Make sure the message must be the same with in logging.properties("IAM_2050512")
    Deploy
    change the  OIMUI.zip to jar
    replace the existing OIMUI.jar
    login to weblogic  and redeploy OIM (oim.ear)
    no need to restart OIM server.
    Test:
    create a request in web console again, you must see the custom message when you hit the submit button
    hope this helps.
    -rad

Maybe you are looking for