N95 NOT registering with service provider.

Hello, I have an unlocked N95 that I am unable to use.
whenever I try to make a call it just says "Connection Error"
My problem is described in detail here...
http://forums.afterdawn.com/thread_view.cfm/507509
please help

Hi and Welcome to the Community!
Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Best!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Similar Messages

  • SPA112 not registering with voip provider

    Hello, I have been trying for weeks to have my SPA112 working but can't make it. My voip provider (voip.ms) says that my device doesn't seem to be working fine. I'm a little new to voip and would like some help to troubleshoot.
    Firmware is the latest (Version 1.2.1 (004)), we have tried many ports, put my router in DMZ, etc. All I get is Registration State:    Failed
    I know my account info is good since I able to register with X-Lite and Zoiper.
    Any idea?
    Thanks.

    I have the same problem. I didn't realise it was happening for quite some time. Then my provider (Three, Australia) wasted my time with service calls and failed attempts to fix it. Finally it went to the store for a few weeks. By the time it went in, the problem had gone from failed txt receipt to failed calls and eventually the phone just shut down completely I think?
    Now, a few weeks later, I've recently been told that people are unsuccessful trying to txt me again. So, again, it's taken weeks to become aware of the problem and I have to take it in tomorrow (at last). Today, I'm told people couldn't call me either.
    If I'd gone in to repair everytime I had a prob I should have had a replacement long ago. Is mine just a bad unit or are these all this bad?
    Does anyone know how you can go about swapping a handset without being penalised for wanting a functioning unit ? Mine will be out of warrantee in just over a month and, unless there's a miracle at the service centre, it'll need work again a week or two after the anniversary of my purchase.
    Three say they can't swap it because they don't have any stock. I just want a reliable phone that syncs with my mac. I don't use it for anything other than calls, sms, diary and alarm clock so I can't be straining it to capacity.
    Any suggestions welcome.
    Thanks,
    mouldfield

  • 11gR2 Install Error, Listener is not up or database service is not registered with it

    Hi all,
    I'm currently studying towards my OCA, I've passed 1z0-051 (SQL Fundementals I), and now I'm moving onto 1z0-052 (Admin 1).
    Im really having trouble creating a database in Oracle 11g R2 Enterprise Edition. I install the software no problem. Then I create a database, and during the creation I have to createsa listener which uses TCP (default port:1521) and IPC. whilst creating the database I get the following error
    'Listener is not up or database service is not registered with it. Start the Listener and register database service and run EM configuration Assistant again.'
    Now, before you lynch me, I have searched this forum for answer to this for a day and a half. I've also tried google, i just can't find a answer that sorts out my problem. please assist me.
    I'm running on Windows 7 Professional (32bit) (I have previously tried on the 64 bit version with teh same results).
    Here's teh contents of my listener.ora file:
    # listener.ora Network Configuration File: C:\app\Damien\product\11.2.0\dbhome_1\network\admin\listener.ora
    # Generated by Oracle configuration tools.
    SID_LIST_LISTENER =
    (SID_LIST =
    (SID_DESC =
    (SID_NAME = CLRExtProc)
    (ORACLE_HOME = C:\app\Damien\product\11.2.0\dbhome_1)
    (PROGRAM = extproc)
    (ENVS = "EXTPROC_DLLS=ONLY:C:\app\Damien\product\11.2.0\dbhome_1\bin\oraclr11.dll")
    LISTENER =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = IPC)(KEY = ipc))
    (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.10.4)(PORT = 1521))
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
    ADR_BASE_LISTENER = C:\app\Damien
    Here's the contents of my tsnames.ora:
    # tnsnames.ora Network Configuration File: C:\app\Damien\product\11.2.0\dbhome_1\network\admin\tnsnames.ora
    # Generated by Oracle configuration tools.
    ORACLR_CONNECTION_DATA =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
    (CONNECT_DATA =
    (SID = CLRExtProc)
    (PRESENTATION = RO)
    Here is the last fe lines of my emConfig.log:
    Jan 18, 2014 9:38:22 AM oracle.sysman.emcp.util.GeneralUtil isLocalConnectionRequired
    CONFIG: isLocalConnectionRequired: true
    Jan 18, 2014 9:38:22 AM oracle.sysman.emcp.util.GeneralUtil initSQLEngine
    CONFIG: isLocalConnectionRequired: true. Connecting to database instance locally.
    Jan 18, 2014 9:38:22 AM oracle.sysman.emcp.util.GeneralUtil initSQLEngineLoacly
    CONFIG: SQLEngine connecting with SID: orcl, oracleHome: C:\app\Damien\product\11.2.0\dbhome_1, and user: SYSMAN
    Jan 18, 2014 9:38:22 AM oracle.sysman.emcp.util.GeneralUtil initSQLEngineLoacly
    CONFIG: SQLEngine created successfully and connected
    Jan 18, 2014 9:38:23 AM oracle.sysman.emcp.ParamsManager checkListenerStatusForDBControl
    CONFIG: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
    oracle.sysman.assistants.util.sqlEngine.SQLFatalErrorException: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
    at oracle.sysman.assistants.util.sqlEngine.SQLEngine.executeImpl(SQLEngine.java:1655)
    at oracle.sysman.assistants.util.sqlEngine.SQLEngine.executeSql(SQLEngine.java:1903)
    at oracle.sysman.emcp.ParamsManager.checkListenerStatusForDBControl(ParamsManager.java:3230)
    at oracle.sysman.emcp.EMReposConfig.unlockMGMTAccount(EMReposConfig.java:1001)
    at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:346)
    at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:158)
    at oracle.sysman.emcp.EMConfig.perform(EMConfig.java:253)
    at oracle.sysman.assistants.util.em.EMConfiguration.run(EMConfiguration.java:583)
    at oracle.sysman.assistants.dbca.backend.PostDBCreationStep.executeImpl(PostDBCreationStep.java:968)
    at oracle.sysman.assistants.util.step.BasicStep.execute(BasicStep.java:210)
    at oracle.sysman.assistants.util.step.Step.execute(Step.java:140)
    at oracle.sysman.assistants.util.step.StepContext$ModeRunner.run(StepContext.java:2667)
    at java.lang.Thread.run(Thread.java:595)
    Jan 18, 2014 9:38:23 AM oracle.sysman.emcp.EMConfig perform
    SEVERE: Listener is not up or database service is not registered with it. Start the Listener and register database service and run EM Configuration Assistant again .
    Refer to the log file at C:\app\Damien\cfgtoollogs\dbca\orcl\emConfig.log for more details.
    Jan 18, 2014 9:38:23 AM oracle.sysman.emcp.EMConfig perform
    CONFIG: Stack Trace:
    oracle.sysman.emcp.exception.EMConfigException: Listener is not up or database service is not registered with it. Start the Listener and register database service and run EM Configuration Assistant again .
    at oracle.sysman.emcp.ParamsManager.checkListenerStatusForDBControl(ParamsManager.java:3245)
    at oracle.sysman.emcp.EMReposConfig.unlockMGMTAccount(EMReposConfig.java:1001)
    at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:346)
    at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:158)
    at oracle.sysman.emcp.EMConfig.perform(EMConfig.java:253)
    at oracle.sysman.assistants.util.em.EMConfiguration.run(EMConfiguration.java:583)
    at oracle.sysman.assistants.dbca.backend.PostDBCreationStep.executeImpl(PostDBCreationStep.java:968)
    at oracle.sysman.assistants.util.step.BasicStep.execute(BasicStep.java:210)
    at oracle.sysman.assistants.util.step.Step.execute(Step.java:140)
    at oracle.sysman.assistants.util.step.StepContext$ModeRunner.run(StepContext.java:2667)
    at java.lang.Thread.run(Thread.java:595)
    Jan 18, 2014 9:38:23 AM oracle.sysman.emcp.EMConfig restoreOuiLoc
    CONFIG: Restoring oracle.installer.oui_loc to C:\app\Damien\product\11.2.0\dbhome_1\oui
    My Listner status output is here:
    LSNRCTL for 32-bit Windows: Version 11.2.0.1.0 - Production on 18-JAN-2014 10:14:39
    Copyright (c) 1991, 2010, Oracle.  All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=ipc)))
    STATUS of the LISTENER
    Alias                     LISTENER
    Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.1.0 - Production
    Start Date                18-JAN-2014 09:27:34
    Uptime                    0 days 0 hr. 47 min. 6 sec
    Trace Level               off
    Security                  ON: Local OS Authentication
    SNMP                      OFF
    Listener Parameter File   C:\app\Damien\product\11.2.0\dbhome_1\network\admin\listener.ora
    Listener Log File         c:\app\damien\diag\tnslsnr\LONDON\listener\alert\log.xml
    Listening Endpoints Summary...
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\ipcipc)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=192.168.10.4)(PORT=1521)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1521ipc)))
    Services Summary...
    Service "CLRExtProc" has 1 instance(s).
      Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
    The command completed successfully
    I can login as sys into my database through sqlplus, so it seems the database is up and running, it just seems to be a listener problem maybe??
    Many thanks for any assistance that you give. I'm learning so be gentle...
    Damien

    SOLVED!
    OK all solved now, thanks to the link to Ed Stevens website that Baris posted (mucho respect )
    Seems that like Barus said I was not using Dynamic Registration, which means that I would need to manua
    ly update the listerner.ora file. On top of that it seems that for some my tnsnames.ora wasn't resolving mt database name so the tnsping wasfailing.
    What I did to solve the name resolution problem
    1. Opened the
    Network Configuration Assistant and saw that my listener didnt have my DB registered with it. So I added it. What this horrible GUI tool does is update the tnsnames and listener.ora files for you. So once that was done I went to the command prompt and did ;'tnsping <dn name> and hey presto it was getting a nice response.
    Then I re-ran my DB Configuration Assistant and tried to reconfigure my database. However it aing failed and gave me the same message that I was originally getting about the DB Service not being registered etc..the lister status still said that same thing:
    Services Summary...
    Service "CLRExtProc" has 1 instance(s).
      Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
    the 'unknown' means that the DB  didnt tell the listener that it was there but instead the listener is in manual mode and will just use the configuration in the listener.ora to know where the DB is.
    So then I followed the steps on the ED Stevens website (follow the link). He has steps which show how to enable Dynanmic registration so that your DB regusters itself with the listener. In a nutshell, he states that he listener actually doesnt need the listerner.ora if using dynamic registration. I shutdown the DB, stopped the listener then I renamed the lsitener.ora to listerner.old, then started the lietener and checked the status and it said 'the listener supports no service' I then started the DB and, then resched teh listener status, it then read 'status: READY'... hooray!, the DB had dynamically registered itself with the listener. I then was able to successfully start up and run Enterprise Manager.
    Thanks for all your help Baris, and Ed Steven website.
    I know more now than when I started so I'm happy.
    Thanks.

  • The collection you specified does not exists or is not registered with the ColdFusion Search Service.

    While upgrading to CF7 from CF5, I am creating the new collections from Cf Admin. After creating, I indexed it from cf admin and then trying to search for the documents in that collection, and i am getting the following error. This was working yesterday. I have cheched the logs etc and nothing seems helpful in discovering what the issue is.
    Document count is 11,745 and the size is 25,948 kb, which is not too much for a collection. I have tried to restart Cold Fusion Search Services and then ColdFusion Application services, but all in vain.
    Any help on this would be greatly appreciated.
    Detail
    The collection you specified does not exists or is not registered with the ColdFusion Search Service.
    Message
    The collection rc_collectiom does not exist.
    StackTrace
    coldfusion.tagext.search.CollectionDoesNotExistException: The collection rc_collectiom does not exist. at coldfusion.tagext.search.SearchTag.verifyLocale(SearchTag.java:819) at coldfusion.tagext.search.SearchTag.doSearch(SearchTag.java:200) at coldfusion.tagext.search.SearchTag.doStartTag(SearchTag.java:159) at coldfusion.runtime.CfJspPage._emptyTag(CfJspPage.java:1915) at cfeFull2dText2dReDirect2ecfm511389924.runPage(C:\Inetpub\wwwroot\External\FullText\eFull- Text-ReDirect.cfm:43) at coldfusion.runtime.CfJspPage.invoke(CfJspPage.java:152) at coldfusion.tagext.lang.IncludeTag.doStartTag(IncludeTag.java:349) at coldfusion.runtime.CfJspPage._emptyTag(CfJspPage.java:1915) at cfApplication2ecfc179940445$funcONREQUEST.runFunction(C:\Inetpub\wwwroot\External\Applica tion.cfc:114) at coldfusion.runtime.UDFMethod.invoke(UDFMethod.java:344) at coldfusion.runtime.UDFMethod$ReturnTypeFilter.invoke(UDFMethod.java:290) at coldfusion.runtime.UDFMethod$ArgumentCollectionFilter.invoke(UDFMethod.java:254) at coldfusion.filter.FunctionAccessFilter.invoke(FunctionAccessFilter.java:56) at coldfusion.runtime.UDFMethod.runFilterChain(UDFMethod.java:207) at coldfusion.runtime.UDFMethod.invoke(UDFMethod.java:169) at coldfusion.runtime.TemplateProxy.invoke(TemplateProxy.java:194) at coldfusion.runtime.TemplateProxy.invoke(TemplateProxy.java:146) at coldfusion.runtime.AppEventInvoker.invoke(AppEventInvoker.java:72) at coldfusion.runtime.AppEventInvoker.onRequest(AppEventInvoker.java:178) at coldfusion.filter.ApplicationFilter.invoke(ApplicationFilter.java:215) at coldfusion.filter.RequestMonitorFilter.invoke(RequestMonitorFilter.java:51) at coldfusion.filter.PathFilter.invoke(PathFilter.java:86) at coldfusion.filter.LicenseFilter.invoke(LicenseFilter.java:27) at coldfusion.filter.ExceptionFilter.invoke(ExceptionFilter.java:69) at coldfusion.filter.BrowserDebugFilter.invoke(BrowserDebugFilter.java:52) at coldfusion.filter.ClientScopePersistenceFilter.invoke(ClientScopePersistenceFilter.java:2 8) at coldfusion.filter.BrowserFilter.invoke(BrowserFilter.java:38) at coldfusion.filter.GlobalsFilter.invoke(GlobalsFilter.java:38) at coldfusion.filter.DatasourceFilter.invoke(DatasourceFilter.java:22) at coldfusion.filter.RequestThrottleFilter.invoke(RequestThrottleFilter.java:115) at coldfusion.CfmServlet.service(CfmServlet.java:107) at coldfusion.bootstrap.BootstrapServlet.service(BootstrapServlet.java:78) at jrun.servlet.ServletInvoker.invoke(ServletInvoker.java:91) at jrun.servlet.JRunInvokerChain.invokeNext(JRunInvokerChain.java:42) at jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:257) at jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:541) at jrun.servlet.jrpp.JRunProxyService.invokeRunnable(JRunProxyService.java:204) at jrunx.scheduler.ThreadPool$DownstreamMetrics.invokeRunnable(ThreadPool.java:318) at jrunx.scheduler.ThreadPool$ThreadThrottle.invokeRunnable(ThreadPool.java:426) at jrunx.scheduler.ThreadPool$UpstreamMetrics.invokeRunnable(ThreadPool.java:264) at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)

    So at last I figured this out myself and found a temporary resolution for this kind of problem. Majority of the times try creating the Collection through Cfcollection tag and then index it using cfindex tag, rather than performing these operations from the Cold Fusion 7 administrator.
    The only reason I can think of which might have caused the issue is – I have thousands of documents in the collection which I indexed. So while indexing the page gets expired. So I tried again to index it. This time the collection got indexed fairly quickly and I got the response that the collection has been indexed successfully. So for the first time when I tried to index the collection, there might be some piece of code, which did not register the collection properly and hence giving this error.
    When I did the same function using the code, with exactly same set of documents, it did not throw any error, even when I executed it for the first time. So the collection indexed properly.
    I am not claiming that technically this theory is correct, but this seems to be the problem.
    If someone knows technically what has happened at the back, please share it. For the time being, this is the fix – if you experience any problem in creating/indexing collections through cfadmin in CF7, do it thorough code.

  • Essbase server is invalid. Not registered with Shared Services

    Hi,
    I am trying to deploy EPMA Essbase application after we upgrade to 11.1.2.2 from 11.1.2.0. I get this error.
    Application server '<Server>:1423' is invalid. It is not registered with Shared Services.
    URI: http://<Server>/awb/integration.verifyApplication.do
    Code: com.hyperion.awb.web.common.BaseServiceException
    Description: Application server '<Server>:1423' is invalid. It is not registered with Shared Services.
    Actor: noneAny specific post configuration task needs to be performed?
    Regards,
    Ragav.

    Hi,
    We were able to resolve the issue. The "Invalid Deployment Information" test in the application diagnostics failed. We had to synchronize the deployment data and later we were able to validate the application.
    Regards,
    Ragav.

  • CF8 Verity "The collection you specified does not exist or is not registered with the ColdFusion Search Service."

    I'm running ColdFusion 8 Enterprise on linux. I'm able to
    create collections and index them through cfadmin as well as in cfm
    application pages, but when trying to search I get the error
    &quot;The collection you specified does not exist or is not
    registered with the ColdFusion Search Service.&quot;
    I'm using the collection name in cfsearch and not the full
    path.

    Would I have been better off posting this in the General
    Discussion section? Could the moderators move it if so,
    please?

  • Cisco 877 router - Cisco IP phone won't register with SIP provider

    Hi all,
    I'm having a problem with a Cisco SPA504G phone not registering with the SIP carrier over the Internet. We've recently rolled out a Cisco 877 router onto a new NBN business connection and can't get the pre-configured IP phone to register.
    When we tested the phone with the NBN-provided Netgear router, it worked fine, as it did with the previous Cisco 1841 router we were using on a different link.
    The way it's setup is using VLANs to define the internal subnets, which are then assigned to the physical interfaces (since the 887 doesn't allow IP assignments to the interfaces directly).
    VLAN 100 is the internal network and has a SBS2011 server – assigned to F0 – IP range is 192.168.1.0
    VLAN 200 is the guest network and has Internet access only – assigned to F1 – IP range is 10.1.1.0
    VLAN 500 is the WAN network and connects to the NBN upstream box – assigned to F3 – external IP address assigned by DHCP
    I've been playing around with access lists, nat rules, basically everything in my limited Cisco knowledge to try and figure this out, but to no avail. I have even configured what I believe is unrestricted access to IP, UDP and TCP outbound and inbound to all VLANs and still can't get it to register.
    Tried isolating the issue by creating a new VLAN and assigning it to the spare interface and basically allowing everything in and out, but still no luck.
    The problem has to be something on the router – probably some small line of config I haven’t removed or added.
    I am going to pull my hair out soon, so would really appreciate some assistance from the Cisco gurus out there.
    My client has just purchased about 10 of these handsets from their provider so I need to fix this ASAP. The guy who provided them wasn't very helpful, and basically said I'm on my own once we tested using the NBN-provided Netgear router.
    Happy to post my config as well.
    Please help!!!!

    Current configuration : 4912 bytes
    version 15.1
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname Router1
    boot-start-marker
    boot-end-marker
    no aaa new-model
    memory-size iomem 10
    crypto pki token default removal timeout 0
    no ip source-route
    ip dhcp excluded-address 10.1.1.1
    ip dhcp pool GUEST
     network 10.1.1.0 255.255.255.0
     dns-server 10.1.1.1 203.50.2.71 139.130.4.4
     default-router 10.1.1.1
    ip cef
    no ip domain lookup
    ip domain name network.local
    ip name-server 192.168.1.123
    ip name-server 203.23.53.12
    ip name-server 197.12.32.86
    ip name-server 8.8.8.8
    no ipv6 cef
    license udi pid CISCO887VA-K9 sn FGL171220XY
    username admin privilege 15 secret 5 $1$aNsm$N1BCQYkoi8gnURyvloYEX/
    controller VDSL 0
    interface Ethernet0
     no ip address
     shutdown
    interface ATM0
     no ip address
     no atm ilmi-keepalive
     bridge-group 10
     pvc 8/35
    interface FastEthernet0
     description NAC - Internal network
     switchport access vlan 100
     no ip address
    interface FastEthernet1
     description NAC - Guest network
     switchport access vlan 200
     no ip address
    interface FastEthernet2
     no ip address
     shutdown
    interface FastEthernet3
     description **** WAN Port ****
     switchport access vlan 500
     no ip address
    interface Vlan1
     no ip address
     bridge-group 10
     hold-queue 100 out
    interface Vlan100
     description NAC - Internal Vlan
     ip address 192.168.1.1 255.255.255.0
     ip access-group IN-100 in
     ip access-group OUT-100 out
     ip nat inside
     ip virtual-reassembly in
    interface Vlan200
     description NAC - Guest Vlan
     ip address 10.1.1.1 255.255.255.0
     ip access-group IN-200 in
     ip access-group OUT-200 out
     ip nat inside
     ip virtual-reassembly in
    interface Vlan500
     description **** WAN Vlan ****
     ip address dhcp
     ip nat outside
     no ip virtual-reassembly in
    no ip forward-protocol nd
    ip http server
    ip http access-class 23
    ip http secure-server
    ip dns server
    ip nat inside source list NAT-100 interface Vlan500 overload
    ip nat inside source list NAT-200 interface Vlan500 overload
    ip nat inside source static tcp 192.168.1.123 25 interface Vlan500 25
    ip nat inside source static tcp 192.168.1.123 443 interface Vlan500 443
    ip nat inside source static tcp 192.168.1.123 3389 interface Vlan500 3399
    ip nat inside source static tcp 192.168.1.123 80 interface Vlan500 80
    ip nat inside source static tcp 192.168.1.123 4125 interface Vlan500 4125
    ip nat inside source static tcp 192.168.1.124 3389 interface Vlan500 3390
    ip nat inside source static tcp 192.168.1.123 987 interface Vlan500 987
    ip nat inside source static tcp 192.168.1.123 1723 interface Vlan500 1723
    ip route 0.0.0.0 0.0.0.0 55.234.52.43
    ip access-list extended IN-100
     permit udp any any range bootps bootpc
     deny   ip 10.1.1.0 0.0.0.255 any
     permit ip 192.168.1.0 0.0.0.255 any
    ip access-list extended IN-200
     permit udp any any range bootps bootpc
     permit ip 10.1.1.0 0.0.0.255 any
    ip access-list extended NAT-100
     deny   ip 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255
     permit ip 192.168.1.0 0.0.0.255 any
    ip access-list extended NAT-200
     deny   ip 10.1.0.0 0.0.255.255 10.1.0.0 0.0.255.255
     permit ip 10.1.1.0 0.0.0.255 any
    ip access-list extended OUT-100
     permit udp any range bootps bootpc any
     deny   ip 10.1.1.0 0.0.0.255 any
     permit ip any 192.168.1.0 0.0.0.255
    ip access-list extended OUT-200
     permit udp any range bootps bootpc any
     deny   ip 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.255
     permit ip any 10.1.1.0 0.0.0.255
    access-list 23 permit 59.23.164.52
    access-list 23 permit 192.168.1.0 0.0.0.255
    access-list 23 permit 10.1.1.0 0.0.0.255
    access-list 23 permit 120.146.0.0 0.0.255.255
    access-list 23 permit 149.185.12.0 0.0.0.255
    access-list 23 permit 110.44.28.0 0.0.0.255
    access-list 23 permit 110.44.26.0 0.0.0.255
    access-list 23 permit 103.25.212.0 0.0.0.255
    access-list 23 permit any
    bridge 10 protocol ieee
    banner motd ^C
    *      Authorized personnel only!       *
    ^C
    line con 0
     login local
     no modem enable
    line aux 0
    line vty 0 4
     password password01
     login local
     transport input all
    end

  • Getting "The server {85DE1C45-2C66-101B-B02E-04021C009402} did not register with DCOM within the required timeout." on WinXP machine

    Hi,
    I have a windows service written in .Net which access a COM component(This conponent is also written by me).
    The COM component launches Acrobat and uses it for generating Thumbnail files.
    I get following error is logged into event viewer  when CreateDispatch("AcroExch.App", &e)) line is exicuted.
    Error Message: The server {85DE1C45-2C66-101B-B02E-04021C009402} did not register with DCOM within the required timeout.
    This problem occurs only when the windows service run under a specified user account say "TestUser". i.e if service runs under "Local System" account then everything works fine.
    Also this problem only occurs on WinXP machine. i.e same thing on Windows2003 server works fine.
    I have given all required permissions for "TestUser" on  AcroExch.AVDoc and AcroExch.PDBookmark using dcomcnfg.
    Any help will be appriciated.
    Thanks and Regards,
    Anand Mahadik.

    Hello,
    start by running sfc /scannow to check if there is corrupt system files.
    If this does not hellp, I recommend performing an in -place upgrade of your OS.
    This
    posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
    Microsoft
    Student Partner 2010 / 2011
    Microsoft Certified
    Professional
    Microsoft Certified
    Systems Administrator: Security
    Microsoft Certified
    Systems Engineer: Security
    Microsoft Certified
    Technology Specialist: Windows Server 2008 Active Directory, Configuration
    Microsoft Certified
    Technology Specialist: Windows Server 2008 Network Infrastructure, Configuration
    Microsoft Certified
    Technology Specialist: Windows Server 2008 Applications Infrastructure, Configuration
    Microsoft Certified
    Technology Specialist: Windows 7, Configuring
    Microsoft Certified
    IT Professional: Enterprise Administrator
    Microsoft Certified IT Professional: Server Administrator 

  • The server {3EB3C877-1F16-487C-9050-104DBCD66683} did not register with DCOM within the required timeout

    Windows Server 2012 becomes slow and unresponsive, event logs show DCOM errors in event logs. After server reboot server works normally.
    Log Name:      System
    Source:        Microsoft-Windows-DistributedCOM
    Date:          10/28/2014 9:06:32 AM
    Event ID:      10010
    Task Category: None
    Level:         Error
    Keywords:      Classic
    User:          NETWORK SERVICE
    Computer:      ServerName
    Description:
    The server {1F87137D-0E7C-44D5-8C73-4EFFB68962F2} did not register with DCOM within the required timeout.
    Event Xml:
    <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
      <System>
        <Provider Name="Microsoft-Windows-DistributedCOM" Guid="{1B562E86-B7AA-4131-BADC-B6F3A001407E}" EventSourceName="DCOM" />
        <EventID Qualifiers="0">10010</EventID>
        <Version>0</Version>
        <Level>2</Level>
        <Task>0</Task>
        <Opcode>0</Opcode>
        <Keywords>0x8080000000000000</Keywords>
        <TimeCreated SystemTime="2014-10-28T13:06:32.743836700Z" />
        <EventRecordID>165767</EventRecordID>
        <Correlation />
        <Execution ProcessID="760" ThreadID="5560" />
        <Channel>System</Channel>
        <Computer>ServerName</Computer>
        <Security UserID="S-1-5-20" />
      </System>
      <EventData>
        <Data Name="param1">{1F87137D-0E7C-44D5-8C73-4EFFB68962F2}</Data>
      </EventData>
    </Event>

    Hi Avinash,
    If this issue occurs again, please follow steps below to troubleshoot it,
    Use the GUID in the error message to find what application it is.
    Using Regedit, navigate to the following registry value:
    HKEY_CLASSES_ROOT\CLSID\clsid value\LocalServer32. The clsid value is the information displayed in the message. Such as, {3EB3C877-1F16-487C-9050-104DBCD66683}
    In the right pane, double-click
    Default. The Edit String dialog box is displayed. Leave this dialog box open.
    Click
    Start, and then click This PC.
    Using the information displayed in the
    Value data box of the Edit String dialog box, navigate to the program.
    Right-click the program name, and then click
    Properties. The Properties dialog box for the program is displayed.
    To determine who the vendor is for this program, refer to the
    Version tab.
    If you can’t find the file in the corresponding path, please replace with a good file.
    Check if the related service have started. Stop and try to restart it.
    If you have 3<sup>rd</sup> party applications, please disable it temporary, to see if this issue was caused by them.
    For more details, please refer to links below, it provides more possible causes about event ID 10010.
    DistributedCOM Error ID 10010
    https://social.technet.microsoft.com/Forums/windowsserver/en-US/77b1db1d-f186-4515-8f7d-2241942eb9b7/distributedcom-error-id-10010?forum=winservergen
    Best Regards,
    Tina

  • The server {4D8E7D87-0103-42F6-BE82-598C7E90A42C} did not register with DCOM within the required tim

    hello all.....
    when i try to convert .indd file to PDF file in C# , i got the following error
    The server {4D8E7D87-0103-42F6-BE82-598C7E90A42C} did not register with DCOM within the required timeout.
    just 1 day ago i installed adobe indesign cs4 in my system.
    do i need to install anything else???????
    please let me know.
    Thanks in advance.

    Hi Avinash,
    If this issue occurs again, please follow steps below to troubleshoot it,
    Use the GUID in the error message to find what application it is.
    Using Regedit, navigate to the following registry value:
    HKEY_CLASSES_ROOT\CLSID\clsid value\LocalServer32. The clsid value is the information displayed in the message. Such as, {3EB3C877-1F16-487C-9050-104DBCD66683}
    In the right pane, double-click
    Default. The Edit String dialog box is displayed. Leave this dialog box open.
    Click
    Start, and then click This PC.
    Using the information displayed in the
    Value data box of the Edit String dialog box, navigate to the program.
    Right-click the program name, and then click
    Properties. The Properties dialog box for the program is displayed.
    To determine who the vendor is for this program, refer to the
    Version tab.
    If you can’t find the file in the corresponding path, please replace with a good file.
    Check if the related service have started. Stop and try to restart it.
    If you have 3<sup>rd</sup> party applications, please disable it temporary, to see if this issue was caused by them.
    For more details, please refer to links below, it provides more possible causes about event ID 10010.
    DistributedCOM Error ID 10010
    https://social.technet.microsoft.com/Forums/windowsserver/en-US/77b1db1d-f186-4515-8f7d-2241942eb9b7/distributedcom-error-id-10010?forum=winservergen
    Best Regards,
    Tina

  • I can't texted people on iMessage that are not registered with iMessage

    hello,
    I have my iphone, ipad and mac book pro all link together with imessage my phone works fine but if i want to text a person from my mac book or my ipad that are not using an apple product it says the number is not registered with imessage how can i send regular texted with my mac book or ipad.
    thank you

    Hello there, DJ Jason B.
    The following Knowledge Base article provides clarification about how Messages works and which options are available:
    iOS: Using Messages
    http://support.apple.com/kb/ht3529
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • The ELResolvers for JSF were not registered with the JSP container

    I'm trying to configure mojarra on tomcat6 (because I want to use Elastic Beanstalk). tomcat complains:
    Feb 8, 2011 10:24:17 AM com.sun.faces.lifecycle.ELResolverInitPhaseListener populateFacesELResolverForJsp
    INFO: JSF1027: [null] The ELResolvers for JSF were not registered with the JSP container.
    I have tried all sorts of combinations of replacing EL2.2 libs in tomcat/lib, putting the libs in WEB-INF/lib, and the context param:
    <context-param>
    <param-name>com.sun.faces.expressionFactory</param-name>
    <param-value>com.sun.el.ExpressionFactoryImpl</param-value>
    </context-param>
    JSF pages seem to work but I'd rather have a clean startup. Please assist. Thx in advance.

    Thx for replying.
    I have jstl-1.2.jar:
         <dependency>
                   <groupId>javax.servlet</groupId>
                   <artifactId>jstl</artifactId>
                   <version>1.2</version>
    <scope>provided</scope>
              </dependency>
    Which version numbers are you referring to in *.xml? The following?
    <web-app xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
    xmlns="http://java.sun.com/xml/ns/javaee"
    xmlns:web="http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd"
    xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd"
    version="2.5">
    <faces-config xmlns="http://java.sun.com/xml/ns/javaee"
    xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
    xsi:schemaLocation="http://java.sun.com/xml/ns/javaee
    http://java.sun.com/xml/ns/javaee/web-facesconfig_2_0.xsd"
    version="2.0">

  • Property Editor not registered with the PropertyEditorManager

    I´m trying to integrate a fully working jsf 1.1 application into JBoss 4.2.2 which uses jsf 1.2 which isn´t that compatible at all.
    I just have one implementation of the jsf-libs and not any in the application war.
    "ERROR [org.apache.catalina.core.ContainerBase.[jboss.web].[localhost].[samigo].[jsp]] Servlet.service() for servlet jsp threw exception
    org.apache.jasper.JasperException: Unable to convert string "#{authorFrontDoorMessages.auth_front_door}" to class "javax.el.ValueExpression" for attribute "value": Property Editor not registered with the PropertyEditorManager".
    And yes, i have been searching a lot on google and read a lot of the article and forum threads but i haven´t been able to solve this.
    I have been struggling with this problem more than a week now, so please give me a tip on what the problem might be.
    Any idea?

    You shouldn't have any appserver specific libraries in WEB-INF/lib (covered by the webapp's default classpath). Further on the appserver/lib (covered by the appserver's default classpath) should only contain appserver specific libraries and at highest 3rd party libraries which are going to be shared among all webapps. Finally you should NOT have added or modified anything in the jdk/lib (covered by the runtime's default classpath).
    So in case of a default and unmodified environment everything should just work flawlessly. In your specific case it seems that you've unnecessarily added/copied appserver specific libraries in the WEB-INF/lib or that you have duplicated EL libraries from (another) appserver in the appserver/lib or maybe -more worse- in the jdk/lib.

  • Private Expenses with Service Provider and Automatic Assignment

    Hi,
    I have created Private Expense Type in Create Travel Expense Types for Individual Receipts.
    In TRIP- Travel Expense Report when I try to split credit card transaction in TRIP, with the wizard, I see that system is throwing errors, that Private Expenses not assigned to any Service Provider, example- AX (AMEX).
    1. Do I have to assign AX as service provider in Assign Wage Types to Travel Expense Types for Individual Receipts
    2. Do I have to assign Private Expense type during splitting of Private expenses in Private Expense Wizard? I see there is a list of expense types in the drop down in Priv Expense Wizard. Cant system determine automatically the Private Expense Type ?
    Please suggest.

    Dear Vijay,
    1. Do I have to assign AX as service provider in Assign Wage Types to Travel Expense Types for Individual Receipts
    If you maintain Service provider in "Assignment of Credit Card Transact.to Travel Expense Type", then yes you have assigned it as well in wage type assignment. In Wizart you try split or change assignment of another expense type and it seems it by pass it together with Service Provider assignment. 
    Unfortunately for the second question I will be not able to answer.
    But you can check for all expense types you use for AMEX card transaction in "Travel Expense Types for Receipt" in bottom, there you set "Allow Wizard for this Expense Type" assign your Private expense type.
    SAP Help documentation for this field:
    Expense Type for Private Shares
        The receipt wizard uses this expense type to record the personal portion of an expense. This is required, in particular, when a receipt amount paid by credit card includes personal portions. In some cases, the company can be liable for such personal receipts. Therefore, they need to be recorded even when they are not reimbursed.
    Use
        In the view "Create Travel Expense Types for Individual Receipts", you need to mark the expense type in this field as "private costs; no reimbursement to employee."
    Example
        Your employer has received, and paid, a hotel bill for EUR 450. The bill lists the cost of EUR 400 for the hotel room, and the cost of EUR 50 for personal expenditures.
        The best way to record this with the receipt wizard is to enter the expense type for private receipts in the "Expense Type for Private Share" field, in addition to the expense type HOTL. Also, to be able to run the receipt wizard for expense type HOTL, you need to select the "Allow Wizard for This Expense Type" indicator.

  • Greetings everyone, I am knew to this, but all of a sudden my Macbook Pro 13" stopped sending iMessages and claims that my iContacts are not registered with iMessage. HELP PLEASE!

    O I guess my question was too long. To reiterate, my Macbook stopped sending iMessages and states that my fellow iContacts are not registered with imessages. My phone is dead and I need to get a hold of a couple of people, but can't due to this problem. HELP!

    You always do better with the forum for the type of mac or service or programs
      MacBook Pro
    https://discussions.apple.com/community/notebooks/macbook_pro
    https://discussions.apple.com/community/mac_os?view=discussions
    http://www.apple.com/support/macbookpro
    http://www.apple.com/support/
    http://www.apple.com/support/iphonehttp://www.apple.com/support/iphone
    the TITLE is just for a brief catch all like iMessages.  The real part is the body of the question you created for this thread.
    Mac OS X Help
    Isolating Issues in Mac OS
    http://support.apple.com/kb/TS1388
    https://www.apple.com/support/osx/
    https://www.apple.com/support/quickassist/
    http://www.apple.com/support/mac101/help/
    http://www.apple.com/support/mac101/tour/
    Get Help with your Product
    http://docs.info.apple.com/article.html?artnum=304725
    TimeMachine 101
    https://support.apple.com/kb/HT1427
    Mac OS X & Mountain Lion Community
    https://discussions.apple.com/community/mac_os
    https://discussions.apple.com/community/mac_os/os_x_mountain_lion?view=discussio ns

Maybe you are looking for