N96 Maps not working after hard reset

Hey Everyone
Merry Christmas! I've recently done a hard reset on my N96 (V11) and I used the copier in PC suite to reload everything back on, however I can't get maps working properly. It shows my current location but can't calculate a route, it's just hangs on 'calculating route'. I've tried renewing my licences but this doesn't seem to be working?????? any ideas????

Try this.
This problem is usually caused by corrupt map data.
To fix this issue, you first have to delete the current map data. Using File Manager, delete the "Cities" folder on your memory card/mass storage.
Then start up the Nokia Maps application so that it recreates the folder and file structure required for the map data.
Finally, reinstall your map data and voices to the phone using Map Loader.
The latest version of Map Loader can be downloaded from
http://europe.nokia.com/A4984199

Similar Messages

Time Capsule Not Working After Hard Reset

A few weeks ago my MacBook Pro started slowing down to a crawl. Eventually ralised it was due to Time Machine not finding the Time Capsule - a known problem.
Reset the Time Capsule (2TB, 8 months old) but although the Internet is working the light is still flashing amber. Carried out a hard reset and still get back to the same situation - the internet is working through the Time Capsule's wireless network but I am getting the flashing amber light.
My internet connection comes into the house and into a wireless modem. An ethernet cable from the back of this modem comes up to my office where the Time Capsule is located into a fast ethernet swtich and then an ethernet cable goes from the switch and is then plugged into the back of the Time Capsule in one of the three internet ports with the <<->> markings.
AirPort Utility shows me that the internet is working and has a green light whereas the Time Capsule has a flashing amber light and 2 errors. When I click the Time Capsule it tells me that the status is:
- Double NAT
- Ethernet Unplugged
Does anybody have any ideas?
TIA

I was having problems with the 7.3.1 firmware as well. For me, in manifest as though the internal disk had went bad--a blinky amber light and a "Disk needs repair" error. Rolling back the firmware solved it for me.
To do this:
--Open AirPort Utility.
--Click on your TC.
--Click on the "Manual Setup" button.
--When the configuration summary pops up, click on the word "Version".
--From the "Upload" drop-down list that is on the new pane that pops up, select "7.3", and click "Ok".
--Once it reboots, it'll be at 7.3.
Hope this helps. I'll be waiting a few weeks after 7.3.2 comes out to upgrade. I'm not real impressed with 7.3.1. As far as I can tell, it broke more than it fixed.

My ipod shuffle (4th gen) don't works after hard reset with itunes

My ipod shuffle (4th gen) don't works after hard reset with itunes, it don't reads too like USB by Windows.
Before that i've seen error (-50) in iTunes, so i reset ipod.
I've read all tips on this site, but nothing helps me.

No, USB works good. I've tried reset on my friend's PC, and it saw my ipod and reset was done. But when i tried to load music, it wrote me, that i've installed incorrect software.

Ovi Store Not Installing after Hard Resetting c7

Hello Nokia. M from India and new here... Plz help me. After hard resetting by three buttons (home,volume,camera) everything gone like ovi store,ovi maps, social,and many other apps in video and tv.and now when i m installing ovi store it says unable to install.. I also went to Nokia care center to reinstall the software bt still not ovi icon.plz help me
Solved!
Go to Solution.

Hey Frnds Ovi Store Is Working.............yupppyyyyyyyyyyyyyyyy Finally it installed on my c7 and n8 too......
What should hv to do(for those whose ovi is unable to install):
* just Format your phone via *#7370#
* And after that no need to install any qt etc software,just check for SW update in your device.
* And it will show an update of ovi store about 15 MB .
* Thats it.
why it was not showing an update before?
ans. because i hv installed qt 4.7 and qt webkit.so SW update wasn't showing any update.
I will request admin to move this thread to Solution section...
thanx to every one 4 repling

Restore not working after a reset?

Due to problems with some apps I had to reset the iPhone three times now.
After the restore of the iPhone software iTunes asked me if I want to restore the last saved backup. I agreed. But after some scanning the restore failed saying that is is the wrong version.
Anyone an idea? And what is the purpose anyway when restore is not working after reinstalling the iPhone software.
By the way: I have the latest versions of iTunes and the iPhone software.

Izit software or hardware? Confuse:(
Only can use wifi now.
Any way thanks guys for ur suggestion:) amishcake and simes

Ram slots not working after CMOS reset

Im using MSI K9N Neo V2 mb, and it was doing fine until i reseted CMOS. Now 3 out of 4 ram slots are not recognized by BIOS nor Windows. Im sure that ram memory is ok, cause ive checked all of it by replacing it between ram slots, and they're only working in slot nr 4.
I know that the MB is old, but everything was working fine, and suddenly went wrong after CMOS reset
Things i did to fix:
Updated BIOS
Msconfig memory uncheck box
Cleared CMOS with jumper
Replaced CMOS BAT
Checked if smth's wrong with cpu
Cleared RAM slots with rubbing alcohol
System wont even boot without memory in DIMM 4 (ram slot 4), and BIOS only recognizes memory in DIMM 4
This is really frustrating, because there is no reason for smth to not work all of a sudden
Any help? Tnx
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

There is a known issue with Powerbooks with the lower memory slot failing, and it sounds like yours may be starting to fail. At one point there was an Apple recall for a small sliver of Powerbook systems to fix that.
The alternatives are to run with 1GB in the upper slot, try one of the internet vendors that say they can fix that (check references), or install a used logic board. I don't believe Apple is repairing Powerbooks anymore, so if you want to buy a used logic board, you'll need to install it yourself, or perhaps an Apple Authorized Service Provider would be willing to do the work.

Auto spellcheck not working after a reset

I had to reset firefox and since then my automatic spell check has stopped working. I have been into options and the 'check spelling while typing' is checked. I have rebooted, it is still not working. How do I get it working?

Hi purplequeennl,
Did the attribute change?
In about:config check these settings:
layout.spellcheckDefault
It should be 1.
The Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information. <br>
'''Note''': ''This will cause you to lose any Extensions and some Preferences.''
*Open websites will not be saved in Firefox versions lower than 25.
To Reset Firefox do the following:
#Go to Firefox > Help > Troubleshooting Information.
#Click the "Reset Firefox" button.
#Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
#Firefox will open with all factory defaults applied.
Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
Did this fix your problems? Please report back to us!
Thank you.

3gs not working after factory reset

restored factory settings and now have apple logo on screen and phone is doing nothing please help

If you got this after choosing "Erase all content and settings" in the Reset area of the Settings App on the iPhone the fix is DFU Mode Restore.
But first do a Reset, Hold both Home and Power buttons until the iPhone begins to restart. Usually less than 20 seconds.
If nothing, then DFU Mode Restore.
With iTunes open on Computer, connect iPhone, hold both Home and Power buttons for exactly 10 seconds, release Power button, keep holding Home button until iTunes recognizes iPhone in Recovery Mode. This is usually less than 30 seconds more time. If the iPhone screen is now blank, then this is DFU Mode. Restore iPhone Firmware. If you have the Connect to iTunes screen on iPhone this is Recovery Mode, you try the Restore anyway. If it works great, if not try again to get DFU Mode as I described. Even experienced users can have trouble getting DFU Mode, just keep trying you will get it. DFU = Recovery Mode with blank screen.
If this does not work and you have Warranty or AppleCare Coverage take iPhone to Apple for resolution.

IPad not responding after hard reset

My iPad 2 is not responding normally, voice assistance has turned on automatically, I need to triple tap icons to open, and the device is generally operating slowly. I have tried a hard reset, but the issue remains and I can't seem to find the reset function in the general menu settings. Anyone else experienced similar problems. Any assistance greatly appreciated?

If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup).
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.
You may have to force iPad/iPod into Recovery Mode
http://support.apple.com/kb/ht4097

Serial Number does not work after hard drive was replaced

My hard drive was replaced and now FCP 7 does not work even when I type in the correct serial number. Help please. Thanks

You posted your question in the Final Cut Pro X forum.
You should repost it in the Final Cut Studio forum.

Login not working after password reset.

we migrated our ebs system from linux to AIX last week.
previous: 11.5.10.2, 10.2.0.2, linux5.5
present: 11.5.10.2, 10.2.0.2, AIX 6.1
Users are not able to login after they reset their password.
As workaround, we asked them to try the direct forms url: https://host.domain/dev60cgi/if60cgi.exe and they are able to login.
Can anyone help me on this?
Thanks.

Users are not able to login after they reset their password.What is the error they get?
Can you reproduce the issue when you reset the password from the backend (using FND_USER_PKG) or using FNDCPASS?
As workaround, we asked them to try the direct forms url: https://host.domain/dev60cgi/if60cgi.exe and they are able to login.
Can anyone help me on this?Please check Apache log files for details about the error.
Also, please confirm that AutoConfig completes successfully with no errors.
Thanks,
Hussein

HERE maps not working after update

I have a Lumia 822, and after installing the updates yesterday, HERE maps (formerly Nokia Maps) crashes immediately after finding my location. I literally can't do anything with the app.
This doesn't seem to be an isolated problem (Several users at WPCentral commented on it), but I haven't seen anything in the Nokia Support discussions yet, so figured I'd open up the floor.
Anyone else experiencing issues?

Do you have any suspicions as to what may have started it working again? Did you restart or reboot the phone or anyting like that?

Messages on my MacBook Pro is not working after factory reset, how can I enable it?

I just recently (yesterday) got my MacBook Pro Mid-2012 restored after having a few issues with it. So it is totally "clean."
Today I tried to open Messages which worked previously, but it wouldn't let me send a message to anyone (who I could message before the restore) and if I was able to send a message it would show an "Message Can't Be Sent" symbol next to it. I went to Messages > Preferences > Accounts > and saw that my account was enabled but my email used is in a grey font and it will not let me add my iPhone number.
I have signed in and out, deactivated and reactivated the account and I still cannot message anybody.
Please help guide me into fixing this, I have looked at other boards and it doesn't really help me with my predicament. How can I send a message?
Also in the Messages menu, "My Status" is grey and I can't click anything and as well with the "Log In" option. If this can help developing an idea of what might be wrong.

It won't send it to other emails, but it will for phone numbers. Not sure why, but if you can help with sending to other iMessage emails I would appriciate it :-)

Keyboard Backlight not working after SMC reset

I have a Late 2009 MacBook Pro, and I noticed that the backlight for my keyboard stopped working last night. I Performed an SMC reset and powered the computer back up. Again the backlight never came on, but I noticed that if I pressed the keyboard brightness buttons the icon that used to show on the screen showing what the brightness is at, (like the volume one), was not showing up anymore. I checked the keyboard settings and noticed that the auto brightness for the keyboard dissapeard. Anyone have any suggestions?

try to reinstall your firmware, im having the similar problems, but reinstalling wont let me.... http://support.apple.com/kb/HT1237

Bootcamp not working after hard drive transfer

A problem with my bootcamp has occurred. Recently my Macbook Pro (2008 model w/ Leopard OS) broke, and I replaced it with a brand new Macbook Pro 15" (w/ Snow Leopard OS). I transferred all of the files from my old hard drive to my new hard drive, and everything worked fine except for my Windows 7 partition. Every single time I try to boot my partition, it tells my windows fails to start correctly due to a recent hardware or software change, and gives me the option to start it normally, in safe mode, ect. Each one of these options results in the blue screen of death. When I run it in safe mode, the boot gets stuck on the line "windows/system32/drivers/classpnp.sys" I have tried repairing the windows with the OS disc to no avail. I just keep getting the blue screen. I have tried to undo the partition, but when I click on bootcamp assistant I get the message, "Boot Camp Assistant cannot be used. You must update your system software before using this setup assistant." I have run all available software updates (to my knowledge) and bootcamp still refuses to work.
Does this have to do with me switching from Leopard to Snow Leopard? Can anyone help me, I'm completely stumped.

Mark-Kopec wrote:
Prior to replacing the drive I backed up the iTunes folder.
describe in detail how.
Then I restored the folder from an external drive to the new internal hard drive.
again, what did you do ?
iTunes Preferences is set to the iTunes folder location on the new drive.
that tells iTunes where to put newly added items, not where the current media is.
But every time I double click on any song I get the error message, "The song … could not be used because the original file could not be found. Would you like to locate it?" I clicked Cancel every time.
if worse comes to worst, this script may work for you:
_*iTunes Track CPR v1.3*_
This script attempts to locate the files of so-called "dead tracks"--iTunes tracks designated with (!)--that you assume are not actually missing but are still located in the iTunes Music folder in their "iTunes File Order" (Music -> Artist -> Album -> file.xxx)."
JGG

N96 Maps not working after hard reset

Similar Messages

Maybe you are looking for