N97 doesnt boot after disconnection during sw upd...

just vibrates when i press power on and nothing else... and doesn't connect to pc... SOS ...

Then unfortunately you need to send it to your local Nokia Care Point.
You can find your nearest Nokia Care Point at:
For UK
http://www.nokia.co.uk/A4228006
For Europe:
http://europe.nokia.com/A4388379
For Asia-Pacific
http://www.nokia-asia.com/A4416070
Elsewhere:
http://www.nokia.com select your country, go to the support section, then select repair.

Similar Messages

Laptop doesnt boot after installing a new hard drive

HP G60-630us laptop ...replaced hard drive ...installed 3 startup discs.. after you remove the last disc, when you hit continue it is supposed to boot up ...it reads no bootable device ......if you put the first disc in to boot up, you end up back where you started.....i changed the boot order & put hard drive first ...still doesnt boot up
This question was solved.
View Solution.

Hi,
The image you download should just appear as 1 file. You should then use the 'Burn a disc image' option in Power2Go to write this correctly to a disc.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

N97 doesn't go on after disconnected during update

Hi,
i wanted to update my n97 from 12 to version 2.0. During the update my phone disconnected and connected back to my computer while it was busy doing the update. This made the program flip a couple of times and in the end it said can't continue updating. I couldn't do anything with the program, nothing was happening so i took out the cable and now my phone won't work anymore. The phone doesn't go on anymore, it does vibrate when i push the on button but nothing happends. If i try to do the update again my computer can't find my phone. Please help. Thanks!
Solved!
Go to Solution.

Hi lad
If you have not already got your handset fixed, then I will be able to help you out...
Feel free to add me on to my MSN:
Moderator Note: Personal details removed. We kindly ask you not to share your personal contact details on this forum.
Message Edited by zipper22 on 10-Jan-2010 12:37 AM

X220 doesnt boot after spill

Hello,
i spilled water on my keyboard. at first my x220 continued working without any issues but i took the opportunity to take off all the keys and whipe it clean. my computer was in standby at this time. after reinstalling all the keys i intended to start my system and it refuses to boot.
while reinstalling the keys i noticed that the display "flashed up" once what apperead to me as if the computer was switching from standby to hibernating mode. it did this as i was applying pressure to put the left shift key, being just above the vga slot.
when i know press the power button it starts blinking a few times but the screen stays black, no further reaction. if i take out and replace the battery and press the power button, the screen flashes up shortley as it did while replacing the keys of the keyboard and it does so showing a few colored vertical stripes.
what can be the problem here? will it be due to possibly entered water (are they not supposed to be spill resistant) or might i have squeezed the graphics adapter or other sort of hardware when reinstalling the keys? is there anything i can do now? hooking the x220 up to an external monitor doesnt help either. the external screen stays black and the system still does not boot;
thanks for any help. unfortunately i will not be close to any lenovo dealership for support for the next few weeks as there arent any in northern chile.

Hi,
The image you download should just appear as 1 file. You should then use the 'Burn a disc image' option in Power2Go to write this correctly to a disc.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

My MBP doesnt boot after update / Prohibition sign flashes twice and then goes straight to OX Utilities

Hello all,
I thought I would never be here, but I am.
After updating iTunes and Memory Clean in App Store (nothing unusual) my MAC stopped booting properly.
MBP / early 2011 / Mountain Lion
It shows the Apple logo flashing twice the prohibiting sign (cancel circle), after that it goes straight to the OS X Utilities.
Note:
- It recognizes the HD and the Recovery partition.
- Verify permission shows a lot of /Applications/iTunes issues, but I have repaired like 5 times and still showing issues.
- Hardware test passed OK.
- Repair disk, no issues.
- Shift (safe mode) doesn't work (lot of flashing ? folder, apple logo, etc).
- PRAM restarted, twice.
I can't reinstall or launch the ML installer, when I go trough the install process which mandatory requires Internet connection and AppStore login, it states: This item is temporarily unavailable. Try again later.
Please help me, I'm desperate this is my production machine and I'm travelling.
What I'm missing?

You cannot reinstall Mountain Lion from the App Store, but you can install Mavericks which is free and will run on your computer. Here's what you do:
Install or Reinstall Mavericks or Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
OS X Mavericks- Erase and reinstall OS X
OS X Mountain Lion- Erase and reinstall OS X
OS X Lion- Erase and reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.

VM doesnt boot after expanding VHD

Hi,
I am running Win2008 R2 HyperV and i was running a VM with a VHD.
I expanded 50 GB disk to 80 GB after expanding the VM boots into repair mode and when i click command prompt it goes to x: drive but i can't see C: drive.
what are the options to repair this VM i don't have any backup for this? please suggest.
Regards,
Maqsood
Maqsood Mohammed Senior Systems Engineer MCITP-Enterprise Admin & ITILv3 Foundation Certified

Follow procedure here
http://blogs.technet.com/b/danstolts/archive/2011/04/02/how-to-expand-and-extend-to-increase-capacity-on-a-virtual-hard-disk-the-easy-and-fast-way-solve-the-problem-of-out-of-disk-space-on-drive-c-forever.aspx
HTH
Milos

Satellite M200 doesn't boot after RAM 4GB upgrade

Hi,
I recently upgraded my RAM just to speed things up a little as RAM is soo cheap these days.
I have a M200 T2130 Vista came with 1GB (2*512) sticks.
The new sticks are 2 *2GB Dane-elec DDR2 pc2-5300, when I put the two in and rebooted the hard drive light came on briefly and then it just stayed idol, no POST, Bios options.
I tried using a single 512 stick with both new sticks and they both work in a 2.5GB setup just not together also this only works when the 512 stick is in the more internal slot and not the other way around.
So if anyone has had a similar prob or can give me some advice that would be great, I'm not to sure if the motherboard can support 4GB?
Thanks, Dave.

Hi
There are two possibilities why your M200 doesnt boot after the RAM upgrade.
Firstly the installed RAM could be not compatible or could be faulty or the notebook doesnt support the 4GB RAM.
I dont know what M200 do you have exactly but you could check the installed chipset and could check on the Intel page if this chipset would support the 4GB RAM.
Greets

My ipod touch accidentally disconnected during sync, after that it wont sync at all. although it appears to be syncing on botht he computer and ipod, it rushed through "determining which tracks to sync' step and no changes are actually made.

my ipod touch accidentally disconnected during sync, after that it wont sync at all. although it appears to be syncing on both the computer and ipod, it rushes through "determining which tracks to sync' step and no changes are actually made.i restarted both and reset the ipod. i checked to see that the computer recognizes the ipod (yes) and tried to sync over wifi with the same result...(i am afraid to retore to factory original beacuse the problem is about transferring from th computer itunes to the ipod)

There is no good way for yur problem since iTunes sees the iPOd. Yu can ry removing and reinstalling all the Apple software using:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
However, I suspect a restor, first try from backup, is required.

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Can't Boot After New HD + Time Machine Restore

So a couple days ago my 27" iMac running Snow Leopard started making some weird noises and stalling out. Annoyed, I talked for a couple hours with apple tech support which eventually lead me to run an Apple Hardware Test. This test returned the error
"Alert! Apple Hardware Test has detected an error.
4HDD/11/40000000 SATA(0,0)"
I scheduled an appointment at the Genius Bar, and they replaced the hard drive.
After that I got it home and did a System restore from my time machine backup. It finished fine, but when I restarted it got stuck on the grey apple screen with the spinning dial thing.
I called apple back and they had me do a couple things like repair disk, verify disk, and one person had me reboot into this command line mode and type some stuff in. Nothing worked. After that They had me try to reinstall the OS first from archive, and next by erasing the hard drive and doing it. Both times the install fails with a big yellow exclamation point saying that it couldn't install support files and the OS couldn't be installed.
Any ideas how to fix this?
I'm currently trying to restore from my time machine backup again, but I'm not hopeful.

Here's what I got - apologies for any formatting peculiarities.
The problem: 10.6.6 mac won't boot after time machine restore to disk.
Further symptoms: Booting with Command-v shows several errors: usually blued and loginwindow collapse with errors from launchd. Errors will be of the style "dyld: Symbol not found: CSSMOID_APPLE_TP_MACAPPSTORERECEIPT" and other CommerceKit / CommerceCore framework errors.
A solution: Your Framework Security library may be an older version (possible cause with Time Machine below). The easiest way to fix this is to find another, working 10.6.6 Mac, and update the Security library on the broken machine.
Identifying if you're affected:
1) Boot the broken machine into "target" mode - hold "Command-t" during boot until the [Firewire|http://itunesu.utah.edu/terms/images/Firewire_Icon.png] icon appears.
2) Connect the broken machine to the working 10.6.6 machine with a firewire cable.
3) On the working machine, the disk of the broken machine should mount.
4) Open Terminal
5) Run "ls /Volumes" - the name of disk you mounted should be there (in this example, we'll use "Macintosh HD".)
6) Typing in the path of the broken machine, run:
<pre>
nm /Volumes/Macintosh HD/System/Library/Frameworks/Security.framework/Versions/A/Security | grep random_fd | cut -d. -f2
</pre>
(this does a dump of the library, looking for the version value)
If this comes back with the value 22457 (or less?), your Mac is not booting because it does not have the updated version of the Security library, which is required in 10.6.6 since Snow Leopard added the Appstore / Commerce framework.
Fixing if you're affected:
1) First, make sure the working 10.6.6 Mac has a correct version of the framework:
<pre>
nm /System/Library/Frameworks/Security.framework/Versions/A/Security | grep random_fd | cut -d. -f2
</pre>
For 10.6.6, this should be at least "22458"
2) *Be extremely careful at this point* - Make sure on the mounted disk (not the machine you are working on!) run the following
<pre></pre>
2a) Make a backup of the broken library
<pre>
mkdir /Volumes/Macintosh HD/savedLibrary
cp /Volumes/Macintosh HD/System/Library/Frameworks/Security.framework/Versions/A/Security /Volumes/Macintosh HD/savedLibrary
</pre>
2b) Copy the working version over the non-working version:
<pre>
cp /System/Library/Frameworks/Security.framework/Versions/A/Security /Volumes/Macintosh HD/System/Library/Frameworks/Security.framework/Versions/A/Security
</pre>
3) Eject the mounted disk from the working Mac, disconnect the firewire cable, and reboot the "broken" Mac. It should come up.
If it doesn't, you have problem(s) that are probably outside the scope of this. I'd also suggest restoring your original security library that you saved off.
Suspected cause:
It appears that Time Machine never recorded the change to the Security library after the update. If the library hadn't changed, the machine should have failed to boot like it did after restore the moment a 10.6.6 update was applied.
Inspecting the contents of my Time Machine backups before and after updating shows that Time Machine never updated the Security Framework library - why is still not 100% determined, but restoring from it is definitely broken. Combing through the backup databases on my Time Machine disk:
(I upgraded to 10.6.6 on January 6)
<pre>
for name in 2010-12-30-093337 2011*
do
echo -n "In backup on ${name}, version of Security library is: "
nm "${name}/Macintosh HD/System/Library/Frameworks/Security.framework/Versions/A/Security" | grep random_fd | cut -d. -f2
done
</pre>
In backup on 2010-12-30-093337, version of Security library is: 22457
In backup on 2011-01-04-100707, version of Security library is: 22457
In backup on 2011-01-05-082402, version of Security library is: 22457
In backup on 2011-01-06-092846, version of Security library is: 22457
In backup on 2011-01-07-094827, version of Security library is: 22457
In backup on 2011-01-10-093559, version of Security library is: 22457
In backup on 2011-01-11-110542, version of Security library is: 22457
In backup on 2011-01-12-094137, version of Security library is: 22457
In backup on 2011-01-13-103238, version of Security library is: 22457
In backup on 2011-01-14-113145, version of Security library is: 22457
In backup on 2011-01-18-112856, version of Security library is: 22457
In backup on 2011-01-20-114953, version of Security library is: 22457
In backup on 2011-01-21-103642, version of Security library is: 22457
In backup on 2011-01-24-102321, version of Security library is: 22457
In backup on 2011-01-27-002508, version of Security library is: 22457
In backup on 2011-01-27-011931, version of Security library is: 22457
In backup on 2011-01-27-104406, version of Security library is: 22457
In backup on 2011-01-27-114322, version of Security library is: 22457
In backup on 2011-01-27-123928, version of Security library is: 22457
In backup on 2011-01-27-134523, version of Security library is: 22457

Lenovo G400 doesnt boot

Hi Guys
my lenovo doesnt boot
the installation was messed up
windows was setup in drive d
doesnt really matter
is there something i can download to format the laptop
it keeps on restarting
doesnt even reach the login page
thanks

If the battery-LED is blinking fast (approx. 2 times per second) remove the battery, disconnect from power supply and press the power-button for 30 seconds. Then attach the power-supply leave the battery off and try to poweron the notebook. Dead batteries also can lead to the symptoms you described.
More hints:
The Z60 is based on the ThinkPad T43. It also can get "Flexing".
Other causes may be contact with liquids in the past, damaged keyboard, crashed BIOS-update, a short in the USB-ports.
To reset the CMOS you also can remove the BIOS-battery but take care: If BIOS-passwords had been set, you only can run the computer after entering the supervisor-password.
My home-forum: http://www.thinkpad-forum.de
Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
My ThinkPad-Collection

Macbook Pro dark screen after disconnecting from Cinema Display

Dear all,
the issue I am having:
- after disconnecting from Cinema display (having first put my Macbook Pro in "sleep" mode) I just ca't make the Macbook pro scren show anything....black display
- but is it really asleep? NO!!! It just STILL believes it's connected to the Cinema Display
That's what I though was happening, so I thought: "if I now plug in the thunderbolt-to-VGA dongle that I use for the videoprojector then the screen might come back... and.... Voilá! It comes back, BUT starts flickering until in the end it just dissappears....
I can reproduce the error all the time. Worse than that: a reboot does not help at all.
Looks like there is an internal hardware switch that must be left "engaged" and then the Mac just believes it is connected to an External screen and sends the signal though the thuderbolt port instead of through the screen!!!
WEIRD error/bug or whatever!!
I have no idea how to make this reach the Apple guys.... I tried to report a Bug but they asked me to join in as Apple developer which I just can't do (for working issues).
Can anyone tell me if they have had this problem, and whether Apple is taking care of it?
(this reminds me of an issue with an internal switch with the headphones in my old MacBook Pro.... after disconnecting the headphones, the internal switch was not being disengaged, so sound would NEVER come out as it was being sent to the headphones instead of to the speakers... Same problem here but with the Image??? :-((( )
Thanks a lot.
BTW: here go my Mac characteristics:
Mac OSX 10.8.2
Model Name:          MacBook Pro
Model Identifier:          MacBookPro10,1
Processor Name:          Intel Core i7
Processor Speed:          2.6 GHz
Number of Processors:          1
Total Number of Cores:          4
L2 Cache (per Core):          256 KB
L3 Cache:          6 MB
Memory:          8 GB
Boot ROM Version:          MBP101.00EE.B02
SMC Version (system):          2.3f32
Intel HD Graphics 4000:
Chipset Model:          Intel HD Graphics 4000
Type:          GPU
Bus:          Built-In
VRAM (Total):          512 MB
Vendor:          Intel (0x8086)
Device ID:          0x0166
Revision ID:          0x0009
gMux Version:          3.2.19 [3.2.8]
MacBook Pro:
Vendor Name:          Apple, Inc.
Device Name:          Macintosh
UID:          0x0001000D11C0EF80
Firmware Version:          11.1
Port:
Status:          Connected
Link Status:          2
Link Controller Firmware Version:          0.11.4
Port:
Status:          No devices connected
Link Status:          7
Link Controller Firmware Version:          0.11.4

Sometimes I experience the same after disconnecting my 24" display (in seldom cases, the mouse cursor is not painted correctly, as well).
Can you check - when it happens - if in System Profiler > Hardware > Graphic > Quartz Extreme is listed as 'supported'. I found it to be 'not supported' when the scrolling and display behaves strangly. Also the Menu Bar is not transparent any more.
Next to rebooting, logout and login again fixed the issue for me. But I am also looking for a better fix/explanation.
marcus

Right USB Port stops working after disconnecting device since 10.9.2

Hi,
Since updating to 10.9.2 the right USB port on my MBA stops working after diconnecting a device (tested: external hard drive, USB flash drive, USB HSPA Modem). The only way to get the port recognizing the device on that port is to do a restart. If the device is connected from starting the MBA it works fine, if I then eject the drive and reinsert it or a different USB device the device doesn't get recognized. The devices do get power, my WD passport ultra spins up just fine, the USB HSPA modem also indicates it's working (with signal) but nothing shows up in finder or diskutility. If the modem is connected from start (and thus working) and then disconnect from the internet but not remove the drive I can reconnect to the internet. The problem only occurs after disconnecting the device. The port becomes inactive. The left USB port works as expected.
Steps I've taken:
Disk Persmission
PRAM
SMC
Reapplied the 10.9.2 update
Sent feedback to Apple
Some Output:
Boot Mode: Normal
Total CPU usage:
   User 11%                    System 10%
Max %CPU by process (name, UID, %):
   WindowServer         0   4.6
Loaded extrinsic kernel extensions:
   at.obdev.nke.LittleSnitch (4052)
   com.driver.JRDUSBModemData64 (4.0.5)
   com.protech.NoSleep (1.3.3)
Loaded extrinsic daemons:
   net.sourceforge.MonolingualHelper
   com.oracle.java.JavaUpdateHelper
   com.oracle.java.Helper-Tool
   com.microsoft.office.licensing.helper
   com.freemacsoft.appcleanerd
   com.adobe.fpsaud
   at.obdev.littlesnitchd
Loaded extrinsic user agents:
   com.oracle.java.Java-Updater
   at.obdev.LittleSnitchUIAgent
/Library/LaunchAgents:
   at.obdev.LittleSnitchUIAgent.plist
   com.oracle.java.Java-Updater.plist
/Library/LaunchDaemons:
   at.obdev.littlesnitchd.plist
   com.adobe.fpsaud.plist
   com.freemacsoft.appcleanerd.plist
   com.microsoft.office.licensing.helper.plist
   com.oracle.java.Helper-Tool.plist
   com.oracle.java.JavaUpdateHelper.plist
   net.sourceforge.MonolingualHelper.plist
/Library/PrivilegedHelperTools:
   com.freemacsoft.appcleanerd
   com.microsoft.office.licensing.helper
   com.oracle.java.JavaUpdateHelper
   net.sourceforge.MonolingualHelper
Extrinsic loadable bundles:
   /System/Library/Extensions/JRDMassStorageDriver32.kext
             (No bundle ID)
   /System/Library/Extensions/JRDMassStorageDriver64.kext
             (No bundle ID)
   /System/Library/Extensions/JRDUSBModemData32.kext
             (com.driver.JRDUSBModemData32)
   /System/Library/Extensions/JRDUSBModemData64.kext
             (com.driver.JRDUSBModemData64)
   /System/Library/Extensions/LittleSnitch.kext
             (at.obdev.nke.LittleSnitch)
   /System/Library/Extensions/NoSleep.kext
             (com.protech.NoSleep)
   /Library/Audio/Plug-Ins/Components/A52Codec.component
             (com.shepmater.A52Codec)
   /Library/Internet Plug-Ins/Flash Player.plugin
             (com.macromedia.Flash Player.plugin)
   /Library/Internet Plug-Ins/JavaAppletPlugin.plugin
             (com.oracle.java.JavaAppletPlugin)
   /Library/PreferencePanes/Flash Player.prefPane
             (com.adobe.flashplayerpreferences)
   /Library/PreferencePanes/JavaControlPanel.prefPane
             (com.oracle.java.JavaControlPanel)
   /Library/PreferencePanes/NoSleep.prefPane
             (com.protech.NoSleepPref)
   /Library/QuickTime/AC3MovieImport.component
             (com.cod3r.ac3movieimport)
   /Library/Spotlight/LogicPro.mdimporter
             (No bundle ID)
   Library/Address Book Plug-Ins/SkypeABDialer.bundle
             (com.skype.skypeabdialer)
   Library/Address Book Plug-Ins/SkypeABSMS.bundle
             (com.skype.skypeabsms)
   Library/QuickLook/Pacifist.qlgenerator
             (com.charlessoft.pacifist.qlgenerator)
   Library/Services/Clip to Day One.workflow
             (No bundle ID)
Login hook:
   /Library/Scripts/Hooks/login.sh
Global login items:
   $HELPER_PATH
   $HELPER_PATH
   $HELPER_PATH
   $HELPER_PATH
   $HELPER_PATH
User login items:
   iTunesHelper
   Sparrow
   Sort Menubar Items
   AppCleaner Helper
   SurplusMeterAgent
Safari extensions:
   Shut Up
   AdBlock
   SafariKeywordSearch
   Disconnect
   MapTricks
Restricted user files: 28
Font problems: 0
Elapsed time (s): 130
etrecheck output:
Hardware Information:
          MacBook Air - model: MacBookAir3,1
          1 1.4 GHz Intel Core 2 Duo CPU: 2 cores
          2 GB RAM
Video Information:
          NVIDIA GeForce 320M - VRAM: 256 MB
System Software:
          OS X 10.9.2 (13C64) - Uptime: 0 days 0:20
Disk Information:
          APPLE SSD TS064C disk0 : (60.67 GB)
                    EFI (disk0s1) <not mounted>: 209.7 MB
                    disk0s2 (disk0s2) <not mounted>: 59.81 GB
                    Recovery HD (disk0s3) <not mounted>: 650 MB
USB Information:
          EFI (disk2s1) <not mounted>: 209.7 MB
          Radha (disk2s2) /Volumes/Radha: 1.81 TB (1.73 TB free)
          disk2s3 (disk2s3) <not mounted>: 189.89 GB
          Boot OS X (disk2s4) <not mounted>: 134.2 MB
FireWire Information:
Kernel Extensions:
          at.obdev.nke.LittleSnitch          Version: 4052
          com.driver.JRDUSBModemData64          Version: 4.0.5
          com.protech.NoSleep          Version: 1.3.3
Problem System Launch Daemons:
Problem System Launch Agents:
Launch Daemons:
                 [loaded]          at.obdev.littlesnitchd.plist
                 [loaded]          com.adobe.fpsaud.plist
                 [loaded]          com.freemacsoft.appcleanerd.plist
                 [loaded]          com.microsoft.office.licensing.helper.plist
                 [loaded]          com.oracle.java.JavaUpdateHelper.plist
                 [loaded]          net.sourceforge.MonolingualHelper.plist
Launch Agents:
                 [loaded]          at.obdev.LittleSnitchUIAgent.plist
User Launch Agents:
User Login Items:
          iTunesHelper
          Sparrow
          Sort Menubar Items
          AppCleaner Helper
          SurplusMeterAgent
3rd Party Preference Panes:
          Flash Player
          Java
          NoSleep
Internet Plug-ins:
          Default Browser.plugin
          Flash Player.plugin
          FlashPlayer-10.6.plugin
          JavaAppletPlugin.plugin
          QuickTime Plugin.plugin
User Internet Plug-ins:
Bad Fonts:
          None
Top Processes by CPU:
              12%          com.apple.WebKit.Networking
               6%          Safari
               4%          WindowServer
               3%          EtreCheck
               2%          hidd
               1%          Terminal
               1%          notifyd
               1%          opendirectoryd
               1%          com.apple.WebKit.WebContent
               0%          Dock
Top Processes by Memory:
          147 MB          Safari
          137 MB          com.apple.WebKit.WebContent
          49 MB          mds_stores
          29 MB          com.apple.WebKit.Networking
          27 MB          TextEdit
          23 MB          WindowServer
          20 MB          Disk
          20 MB          Sparrow
          20 MB          CVMCompiler
          18 MB          Finder
Nothing out of the ordinairy. Thanks for any help

It's an Apple Pro keyboard and mouse, the dongle is
plugged into the Mac and not the keyboard. The same
set-up is, and has been working on all our other
Macs.
The sleep issue sounds interesting- hum, maybe...
Is your keyboard plugged into one of the USB connections on an Apple monitor? If so, you may want to change that connection to one that is on the G5 itself. My monitor came with a warning note indicating that problems will likely occur if the keyboard is connected to the monitor.
I also had a problem with the automatic sleep function. After much trouble-shooting and a logic board replacement, it was concluded that coming out of the automatic sleep function with any USB device active would freeze the entire USB bus. After disabling automatic sleep in system preferences, I've had no freezing problems. My machine works fine with the manual sleep function in the Apple Menu.
AndyH

HDMI does not come back after disconnect

Hello Archers,
this one is bugging me for a while now, perhaps someone has an idea.
I have a headless ARCH home server that mainly has the following purposes:
1. being a 24/7 file/backup/ssh server for family and friends
2. being an MPD server connected to my music system
The setup may seem a bit exotic. The computer is connected to the music system via HDMI over an S/PDIF audio extractor to the music system. This is because the machine replaced a RaspberryPi that really had crappy analog audio output and my music system has an optical input and can perform the digital to analog conversion itself. I have not installed Pulse just alsa and jack2-dbus.
aplay -l shows the following:
**** Liste der Hardware-Geräte (PLAYBACK) ****
Karte 0: PCH [HDA Intel PCH], Gerät 0: ALC887-VD Analog [ALC887-VD Analog]
Sub-Geräte: 1/1
Sub-Gerät #0: subdevice #0
Karte 0: PCH [HDA Intel PCH], Gerät 3: HDMI 0 [HDMI 0]
Sub-Geräte: 0/1
Sub-Gerät #0: subdevice #0
The Problem:
Whenever I switch off the music system and later switch it back on, the HDMI-connection is lost and does not get reestablished. I tried various things but essentially only a reboot of the machine helps (which opposes purpose 1 of the machine). On the RaspberryPi I did not have that problem, probably due to the hdmi_force_hotplug=1 in /boot/config.txt.
My Observations so far:
The first problem that made the sound disappear was the screen blanker on the console after 10 minutes. This can be prevented with
setterm --term linux --blank 0 >/dev/tty1 # You need write permission on /dev/tty1 for this to work!
There are no appearant error or warning messages when using e.g. aplay or speaker-test, just no sound at all
There are tipps in the forums/the internet sugesting to disable power management on the display involving xset and xrandr. However, I have no X running and the tools complain that they cannot find/open the display
In /proc/asound/PCH/codec#2 I find the HDMI codec to show the following as long as it is connected after a reboot:
Codec: Intel Valleyview2 HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862882
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D3
Power: setting=D0, actual=D0
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3
Power: setting=D0, actual=D0
Node 0x04 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="HDMI/DP,pcm=3 Jack", index=0, device=0
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="ELD", index=0, device=3
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=01, enabled=1
Power states: D0 D3
Power: setting=D0, actual=D0
Connection: 2
0x02* 0x03
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x80]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x58560020: [N/A] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D3
Power: setting=D0, actual=D0
Connection: 2
0x02 0x03*
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x80]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x58560030: [N/A] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D3
Power: setting=D0, actual=D0
Connection: 2
0x02 0x03*
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono
After disconnect/reconnect it changes to this:
Codec: Intel Valleyview2 HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862882
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
N/A
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power: setting=UNKNOWN, actual=UNKNOWN, Error, Clock-stop-OK, Setting-reset
Invalid AFG subtree
I figured that the problem is probably related to powermanagement, so I experimented with powertop. This resulted in a reduced consumption of 1W when idle, which is nice but did not solve the original problem...
The Questions
Is there a way to completely reinit the HDMI subsystem just like on a reboot?
Is there an option comparable to hdmi_force_hotplug=1 on the pi that forces the HDMI signal to stay up?
Thank You for Your time!
Best regards,
Lars

I can confirm what zofiel said. I have tested it by connecting a TV and HDMI reactivitated by switching from X to console. However, this option only works one time and requires X running in the first place, which I usually have not on a headless server, but it made me think: Obviousely the X server needs to activate the graphics in the first place. Then I came up with an idea for a really messy work around. I could try to remotely start X. Normally, this is not possible and you get:
% startx
/usr/lib/xorg-server/Xorg.wrap: Only console users are allowed to run the X server
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server error
You can force it to work:
sudo startx
You get lots of error messages, but HDMI audio is back, even if one kills the X process afterwards with Ctrl+C (Audio stops, but resumes two seconds later). The downside is that starting X with sudo messes up permissions with the x related files in your home directory and you will have problems to use startx afterwards, so it is probably better to use su instead of sudo. If root does not have a properly configured .xinitrc file then one can also just execute the desktop environment directly e.g., for XFCE:
su - root -c "startxfce4"
Then kill it with Ctrl+C and you should have HDMI Audio working.
So now I could pack this in a script followed by some command to kill it, but, well, it is an ugly workaround
Is there really no better way?

Apple TV disconnected during streaming and now I can no longer access the AT menu.

Our Apple TV3 suddenly disconnected during playback of a TV episode purchased from iTunes. I downloaded this episode onto our Mac OSX 10.8.5. earlier this year. We had watched it before with no problem, but tonight it quit midway through and we received the message that "Apple TV cannot connect with iTunes". I checked and found that Home Sharing was still on, but since I had this problem once before, I turned Home Sharing off in iTunes and the turned it back on, signing in as required. Despite several attempts, we could not get the program to restart. Then we got the message that "Apple TV cannot sign in to iTunes". We tried to reset Apple TV but now we cannot connect to the menu. I pressed the menu button on the remote several times but got nothing. The remote battery is relatively new and we haven't used the ATV much since then. All the ATV software is up-to-date and we have the most recent version of iTunes. Any help getting the menu to appear would be appreciated as well as any help getting the program to play. Thanks.

Hi Lourufmom,
Welcome to the Apple Support Communities!
I understand that you are unable to access your Home Sharing library on your Apple TV after it disconnected while watching purchased TV episode. The first troubleshooting step that I would recommend, that you may not have yet completed, in this situation would be to restart the Apple TV. Please let me know if the issue continues after restarting your Apple TV.
How to restart your Apple TV - Apple Support
If you can't restart your Apple TV because it's unresponsive, try the following:
Hold down Menu and Down on the Apple Remote for six seconds, and then release when you see the indicator light on the Apple TV blink rapidly.
Unplug the Apple TV power cord for three seconds, and then plug it back in.
Have a great day,
Joe

N97 doesnt boot after disconnection during sw upd...

Similar Messages

Maybe you are looking for