N97 Firmware Upgrades after V20

Are there any chances of a firmware upgrade for N97 after V20 which will further increase the speed. The kinetic scrolling is still not very smooth and sometimes the screen freezes for a second or two. Anyone facing a similar problem ?

Nokia usually continue to update/improve software with anew model at least for 2 or 3 years, don't know what the next one holds, but I believe it is imminant, V2.1 due this month I believe. My phone's worked pretty well since V2.0.
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution' 

Similar Messages

  • SunRay 2FS DTUs dead after Firmware upgrade?

    Hi everyone,
    although I am fairly experienced in Solaris this whole Thin Client business is a bit of unchartered territory to me as of yet... following situation:
    I got 2 SunRay 2FS DTUs and I have a vanilla PC setup with Solaris 10 U6 for x86. Installation was smooth except for the onboard NICs - I had to locate and manually install the appropriate drivers (skge). Installed SRSS 4.1, no problems, made a basic configuration (skge0: standard LAN, skge1: SunRay LAN with the standard 192.168.128.0/24 network). Installation told me DTUs would be firmware-upgraded after next power-cycle. Fired up the first DTU, it displayed the firmware upgrade OSDs and power-cycled - so far so good. But after the power cycle nothing happened - LED on the front is green so obviously POST is okay but the OSD constantly display status "1" (waiting for ethernet link to come up) and nothing else happens. Link lights on the NIC are on, when I send packets on the skge1 network (pings) they even flash, so I assume it's not the cables. Strangest things of all: I tried DTU 2 and the exact same sequence happened - so I am sitting here with 2 dead DTUs - any chance of reviving them? I scoured the 'net for information but I got no description that was even close to my problem...
    Kind regards from Germany,
    Henning

    after installing sun ray server remember to:
    1) utadm
    2) utconfig
    http://docs.sun.com/source/819-2383/config.html#59570 <- old but right

  • N97 cannot use as modem after firmware upgrade

    Hi, sorry if this is a repeat post but driven to distraction.
    I use my N97 as a modem to connect to the internet from my laptop when I'm away from home. Since upgrading the firmware I cannot connect through 1 touch access or direct through dial up.
    When attempting to connect through 1 touch I get as far as connecting device and then I get the message "Failed to connect device".
    I have removed the modem through internet properties and reinstalled PC Suite (after using PC suite cleaner). I am running windows 7 but was connecting through 7 before the firmware upgrade.
    Now I'm at a loss. Anyone got any ideas?

    Saw another post here that said they make a completely new network with a different name and it worked. I decided to give it a try and it actually did work!!! Don't have any clue why but I don't really care since my network is running again.

  • PC-Suite sync fails after Firmware upgrade of E65

    After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
    - PC-Suite updated to 7.0.9.2
    - Outlook 2003
    - XP Prof.
    Any ideas?
    Solved!
    Go to Solution.

    The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
    Does somebody has an idea?

  • No power after firmware upgrade on nomad jukebox zen xtra

    I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

    I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

  • No contacs after firmware upgrade on N70

    Hi
    I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
    I did the upgrade again just to make sure that everything went OK with the same result.
    Can some help or has the same problem?
    Firmware V 5.0638.3.0.1 18-09-06 RM-84
    PC Windows XP SP2
    Nokia PC Suite 6.82.22.0
    NSU 1.2.0en
    Best regards
    Chris

    not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

  • HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

    Hello,
    I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
    After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
    Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on  my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
    Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
    Thank you in advance for a reply - especially from HP.

    Hi cyskim,
    Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • HP 5524 Wireless does not work after firmware upgrade

    HI,
    I have just purchased an HP5524.  After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
    The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully. 
    However, ever since wireless will not work.  Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum.  The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
    Thank you

    Hi,
    Thank you for posting you query,
    In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen  instructions.
    If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup  and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"
    (Although I am employed by HP, I am speaking for myself and not for HP)

  • After the firmware upgrade last week, the local WIFI networks pop up when I turn on my phone, I have WIFI turned off, how do I turn off the pop up?

    After the firmware upgrade last week, the local WIFI networks pop up when I turn on my phone, I have WIFI turned off, how do I turn off the pop up?

    What OS X version are you using?
    Can you take a screenshot of the pop-up notification?
    To take a screenshot hold ⌘ Shift 4 to create a selection crosshair. Click and hold while you drag the crosshair over the area you wish to capture and then release the mouse button. You will hear a "camera shutter" sound. This will deposit a screenshot on your Desktop.
    If you can't find it on your Desktop look in your Documents or Downloads folder.
    If you want to attach a screenshot to a response here, click the "camera" icon above the text field:
    This will display a dialog box which enables you to choose the screenshot file (remember it's on your Desktop) and click the Insert Image button.
    ⌘ Shift 4 and then pressing the space bar captures the window the cursor is on.
    ⌘ Shift 3 captures the entire screen.

  • Fans And Voume after FirmWare Upgrade

    Hey there!
    I have two very positive pieces of information, some repeated:
    1) The volume of my speakers and "line out" was weak at best prior to the FirmWare upgrade. Now, it is positively explosive! I mean, the volume control works just like I would have expected. Perfect...
    2) The fans are coming on more consitantly. I can actually hear them now, which makes me wonder... The temp on the Hard Drive has not gone above 92 since I upgrade the firmware (not that I have noticed however).
    Bob

    Hi Bob!
    What did you use to check the temperature?
    I installed the 10.4.6 and the firmware, and now I could cook an egg on the keyboard. I didn't have the heat problem before, now after the updates, I am fried (literally).
    Gus

  • Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

    Hi,
    I upgraded my device after I got an email that there is a new firmware:
    An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
    I installed the update but now it is stuck at 95% after rebooting.
    Never had any problem before the firmware upgrade. 
    Any advice?

    Hello BelgianTomas
    I recommend that you first power down the unit if the unit has not completed the boot process.  Then re-seat all disks and try booting the unit again.  Please do not try to access the web interface until the power led is solid white.
    Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot. 
    If that does not help, LenovoEMC suppor should be contacted for more advanced options.
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • Problem After 1.52.02 Firmware Upgrade

    I have a BEFW11S4 v4 wireless router.  I am frequently having to reset my router after the firmware upgrade to 1.52.02.  I have had this router for years and have had very few problems.  After the firware update,  I am constantly losing my connection to the internet.  If I unplug the router and plug it back in,  it works fine.  This happens to me several time a day sometimes.  I would go back to an older version of firmware if one were available.  Anyone else having this problem ?  Anyone have a solution ?

    Don't go with the older firmware version, try to hard reset your router...
    Press and hold the reset button for 45 seconds...Release the reset button...Unplug the power cable from your router, wait for 45 seconds and re-connect the power cable...Now re-configure your router...
    You should also adjust the wireless settings on your router...
    Wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
    In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4.
    Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers...

  • Failed to go through WRT54G v3.1 router after firmware upgrade

    Upgraded to latest 4.21.1 firmware.
    After upgrade I don't have access to internet anymore through the router.
    Symptoms :
    - Router has access to internet : ping OK, DNS resolution OK
    - Router has access to home PC (both wired and wireless) : ping OK
    - home PCS can ping router
    - home PCS can't go through router to internet (ping and DNS resolution won't work)
    Seems like the "forward chain" is forbidden in the router (I'm using linux iptables "forward chain" meaning here).
    Any ideas ?
    Tx
    David

    Yes, connecting the pc directly to the modem works fine (that's how I posted this message). Reconnecting/reconfiguring have been done __a_lot_of_time__ before going to this forum.
    I've finally installed DD-WRT and everything's working fine now.

  • After time capsule 7.6 Firmware upgrade I can't set up Access Control / Timed Access using mac adresses.

    After time capsule 7.6 Firmware upgrade I can't set up Access Control / Timed Access using mac adresses.
    I have a Time Capsule and an Airport express and when I change access control parameters on whatever one of those
    two devices through Airport Utility its duplicating the same setup on the other device !
    What a mess !
    I had to choose "Not Enabled" in the Access Control stup window.
    Has anyone experienced same problem ?
    Jean.

    I did downgraded firmware to 7.5.2 ...
    and the Acess Control Setting from Airport Utility is back to normal behaviour.
    Jean.

  • BEFW11S4 constant disconnect after firmware upgrade

    I was having trouble with my router losing connection every 2 hours or so . I have downloaded and installed the latest firmware and now it keeps disconnecting almost every 30 min. I have a static IP on my main pc and dhcp enabled for my xbox360. I have checked the cables if they were bad by swapping them but the problem was still there. Any help would be very much appreciated.

    After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch.  If you saved a router configuration file, DO NOT use it.
    Also, please list all the static LAN IP addresses that you are using on your network.
    If you are not using the default DHCP server range of 192.168.1.100  thru  192.168.1.149 , then please state your DHCP server range.
    Are you running any peer-to-peer (P2P) software?  If so, this is a known cause for router slow downs and disconnections.  Temporarily stop using the P2P software, then reboot router, and see if this corrects your problem.
    Who is your ISP?  Are you on a cable system?  Some cable systems monitor the MAC address of the devices connected to them, and eventually boot off any MAC address they don't recognize.  If you are on a cable modem, try cloning your MAC address (done in the router), and see if this corrects the problem.

Maybe you are looking for