N97 Memory Problem after Firmware Update

Hi all,
im having trouble with my N97.
i recently updated the software using the nokia software updater....
now, when the phone turns on it comes up " not enough memory to perform the operation "
then after it says " memory full, delete or move some data from C: Phone memory. " 
before i get chance to do this the phone crashes and goes through the same process.
ive tried deleting and moving files when the phone is just plugged into my laptop.
but it persists in restarting after like 30 seconds of being switched on...
any suggestions ? 
thanks

 make sure you have a back up of your device which you s hould have anyway since you just did update and reformat your phone 
*#7370# the default code is 12345 and then try the things listed below as well  
/discussions/board/message?board.id=topfaq&thread.id=159
try this and also when you install y brower or similar go to c drive
system and delete drmg and cache folders. no worries they self replicate.  
Message Edited by radical24 on 15-Dec-2009 03:37 PM
Message Edited by radical24 on 15-Dec-2009 03:38 PM
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Similar Messages

  • Problems after firmware update 52.0.007

    Hi,
    I got my phone back after the shop fixed a problem and updated the firmware to the latest version 52.0.007.
    But now I have following problems:
    I can't get the calendar anymore to show up on the homescreen, even after checking the checkbox to do so
    The Radio app. is gone
    Does anyone has a solution for this?
    Iwan

    It may sound crazy but sometimes you need to "hard reset" device after firmware update (beware all data erased) by keying in *#7370# followed by 12345 (default Nokia lock code unless altered by yourself). Sometimes UDP = User Data Prersevation feature of 5800XM can carry over corrupt entries when updating.
    Happy to have helped forum with a Support Ratio = 42.5

  • T43 1875 upper memory ERROR after firmware update

    Hi, I got new HD hts541612j9at00 and run a bootable CD with the latest firmware update file to correct the Error 2010. However, after rebooting the system I am getting the following message (and the system freezes):
    Starting Caldera DR-DOS
    ...(Copyright  bla..bla ...bla) 
    EMM386: Cannot find an unused 64 kb range reserve of upper memory to use for an EMS page frame.
    Any thoughts how to solve this problem with the upper memory ?

    I'm haveing exactly the same problem with my Thinkpad.
    Nobody around with any thoughts?

  • C3-01 Problems After Firmware Update

    After updating the firmware from v5.65 to v6.0 the phone lost some features -namely:
    Chat
    Media Player
    Ovi Store
    "Favorite Contacts" on homescreen
    default wallpapers
    Solved!
    Go to Solution.

    Finally, I've fixed the problem!
    Going back, I updated the phone from 5.65 to 6.0 via OTA(over-the-air) update -in other words, I updated the firmware using the phone while connected to my home wi-fi network.
    In desperation to find a solution, I hesitantly re-updated the phone... But this time via PC.
    I opened Ovi Suite and updated the phone -again, expecting it would reinstall version 6.0 .
    After the update, all the apps that I've lost came back.
    I then checked to confirm if it was indeed version 6.0 -alas, it was not... It was version 6.05.
    Now, everything is working as it should be; mail, chat, ovistore, calculator, favorite contacts on homescreen -everything!
    It feels good to figure it out all by myself.  Hehehehe!!

  • Audio in problem after firmware update

    hey all,
    I've recently started using garageband to record and play around with my music, and I love it. Unfortunately, after installing the recent firmware update, my computer's audio in jack doesn't work anymore. It recognizes that there's something plugged in, but instead of having an signal, I get this clicking that clips the audio input at almost any input volume. I have tried it both with my bass and just the cable, and I have also just plugged some headphones into the jack- same results for everything. Is there anything i can do about it or do I just have to wait for another firmware update before I can use garageband again?
    2.2Ghz Macbook Pro   Mac OS X (10.4.10)  

    well what happened was I was updating iTunes (7.3.1) and the updater said a quicktime update and a firmware update were both available so I downloaded and installed and now the problem. It's like a really fast click track when I plug in and it's not just in garageband, I'm getting it in the audio-in option in the system preferences menu. Do you think doing a system restore would solve this problem?
    PS- I believe the update was something along the lines of a "kmbp firmware update" I think that's what it was called... :/

  • Overheating problem after firmware update

    Hi,
    A friend of mine noticed a CPU temperature increase in between 10 and 15 per cent, after the MacBook EFI Firmware Update 1.1. Has anyone else noticed a similar behavior? Any ideas or suggestions?
    Thanks in advance,
    Gonzalo

    Originally Posted by ketter
    HP DL380 G7
    OES 11 SP1 / SLES 11 SP2
    patched up to March 29, 2013
    HP LTO-5 Ultrium 3000 tape drive
    Arkeia backup software
    Everything was running fine. I updated the server firmware using the
    HP Proliant Service Pack on Apr 10, 2013 and haven't been able to get
    a good backup since. Arkeia support says problem with the hardware.
    But testing with the HP diagnostics says the hardware is fine. I
    checked with HP support and they agree that the hardware is fine but
    there are some communication issues. They recommended that I upgrade
    the driver. They sent me here:
    HP Smart Array P212 Controller*-* * RECOMMENDED * HP ProLiant Smart Array Controller (x86/AMD32) Driver for SUSE LINUX Enterprise Server 11 (x86) - HP Business Support Center
    I attempted to install that, but it failed due to dependencies. So
    before I go any further and risk messing something up. Does anyone
    have suggestions for this? If I do need to update the driver, is
    there another way I am supposed to do it vs using the driver from the
    HP website? Or how do I deal with the dependency issues...the only
    patching I have done with SLES so far is through the channel.
    Ken
    may i ask what kind of dependency issues you're facing? i've installed the SP2 (kernel 3.0.x) based package last weekend without any issues on a default kernel. are you sure that you've grabbed the rpm matching your kernel version?

  • N78 problems after firmware update

    I have recently updated my N78 (RM235) firmware to 13.052.231.6.
    Before the update the internal GPS worked very well, finding satellites quickly and holding a strong lock. After the update the GPS is very poor, taking a long time to find satellites and loosing signal very easily.
    Can anyone help with this problem or tell me how to re-install the previous firmware?

    Has everything else stayed the same and only the GPS antenna reception got worse?
    If that is the case you are right, but maybe the update made other improvements and for some reason one of them worsened the GPS antenna...just guessing...  
    By clicking the "Kudos!" or the "Solution?" button on the right you can say "Thank You" and you´ll show the author and others that the post is useful.
    The day we stop improving is the day we stop being good.

  • Problems after Firmware update

    I have a big problem with my ipod nano, @ the firmware update it disconnects from pc and now it didn't work anymore because of a mistake in the firmware what can i do? please help me

    If you have symptons stated on this thread, try the steps there.
    http://discussions.apple.com/thread.jspa?threadID=544840&tstart=0

  • E3000 problems after firmware update

    It seems internet browsing doesn't work after the firmware update.  Everything else works , aim steam msn, bittorent but anything http related will not work.

    on both computers i have run some tests
    ping 127.0.0.1 -fine
    ping 192.168.2.1 - fine (gateway)
    ping 192.168.2.3 (another computer) fine
    ping 192.168.2.254 dsl modem (fine)
    ping www.comcast.net fail
    I have thought it could be the DSL modem but it works  just fine when i use my Belkin pre-n router and the Belkin never needs a power cycle.
    I can get HTTP functions when i reboot the router. 
    I have also set up a DYNDNS to see if a friend could ping me and connect to  a server for me thru my IP address and it was successful its just websites and this is happening on all the computers and playstations (theres 2)

  • Sony SBH50 Multipoint problem after firmware update

    I recently updated the firmware on Sony SBH50 bluetooth headset and now, I cannot use Multipoint anymore.  I have to switch off and pair individual devices while Multipoint was working well before the firmware update.  Please advise what to do

    I just purchase it and I cannot connect to my Z3 in same time as my Z3 tablet compact.  it is last version of soft and on firmware

  • Z68A-GD65 (G3) Memory problems after BIOS update

    Good day, i'm russian, so sorry for my english.
    Friend of mine had MSi Z68A-GD65 (G3), i5-2500K, memory pair 2*2GB with bios 22.8 (latest version with no red letters about ME8 and IvyBridge).
    He decided to upgrade the processor to IvyBrydge and updated bios with new ME8. Then the computer went into a state of continue restarting every 3 seconds. After replacing the CPU to the new Ivy - computer works good, the impression is that the computer does not understand Sandy now and switched toIvy. But it has seen only one of memory pair. My friend just bought a new motherboard. Now he has no problems. I took his MB and SandyBridge CPU.
    Flashing the bios to the old version by M-Flash - it does not see the BIOS file, although it is there (in the root, FAT, 2G). Flashed it under dos with AFUDE238 with a key -x, it said about mismatched ROM ID. After the old BIOS flashing (with an Ivy) computer went three-second reset mode. CPU changed to Sandy i5-2500K - now works good. By the way, now M-Flash see the firmware on a flash drive - I flashed it again from the M-Flash, just in case, reset the settings.
    What is the problem: if I set the memory into the slot 3 or 4, the computer goes into a three-second reboot, it does not matter is the memory in the first two slots or no. If this memory is inserted in the first two slots - all ok. So I work now - in the first two slots with no dual-channel mode.
    The feeling is that the problem appeared after first flashing to Ivy and remained after flashing back to Sandy.
    Question 1: What to do to get working the memory slots?
    Question 2: Is BIOS 22.8 - the latest which I will have with Sandy? (There is a problem now when the computer starts - 1 times out of 10 will not boot - reset is helping, and the BIOS at starting not very fast).
    There are posts about people with the same MB and the CPU and the new BIOS (25.2) that supports Ivy. I'm confused. It means I can use the new firmware from SandyBridge. But there are many posts about problems with new firmware. Where is the true?
    Just checked BIOS version -  P.1 (25.1) 2012-04-16 - by the way with Ivy support. But I flashed with 22.8, I'm sure. ME version in BIOS isn't shown, but while booting - ME 7.0
    What does it mean? Can it be repaired? What should I do?

    Thanks to all. My system is working fine now.
    What it was. I flashed BIOS with tool from this forum. Bios flashed good, but problem still was here. Then I flashed to the first bios version from support site. And again flashed ok but memory still not working in slots 3 and 4. Then I decided to flash back to last flash with Sandy support 22.8 (or 23.8). Then I flashed to the last bios at all - 25.4. Flashed it from dos - this was pretty long. It rebooted 3 times (ME updated too). I still don't know  - what it was with first flashing to Ivy. Now it's ok.
    So I decided the problem is bent pin. With magniglass and needle I've found some uncertain pins (these were not BENT, but slightly bent) and touched these with my needle. And that was the answer. Now all works fine. Thank you all.
    On the russian msi forum no one answered and helped me at all.

  • 5800 problem after firmware update

    hi!
    I updated my nokia 5800 yesterday to  the new firmware v50. But today the whole touchscreen does not work at all. Only the three physical buttons and the unlock button on the side works. I have tried to turn it of but it did not help. I took out the battery and the memory card but i have still the same problem. Does anyone of you know what is wrong?

    /t5/Nseries-and-S60-Smartphones/5800XM-hard-reset-after-upgrade/m-p/462564#M137151
    So.. might have to go for a Hard Reset.. but Take a Back-up before doing...
    --------------------------------------------------​--------------------------------------------------​--------------------------------------------------​--If you find this helpful, pl. hit the White Star in Green Box...

  • N97 homepage problems after software update

    Hi Everyone,
    After updaing my N97 to software version 21.0.045, which was a nightmare as the phone memory ran out, I have lost several applications from the home screen.
    The email summary widget, music widget and date/time part, and they're not available in the list of available content if I try to add them.
    Any ideas anyone?
    James

    psychomania wrote:
    I'm not being offensive. Just stating facts.
    I am simply highlighting the fact so that the user will see it and be aware of what you suggested would do.  Sorry if you took offence at that but the user comes first.
    of course customer first , i'm doing this with happiness , cause i'll be very happy to help them without reaso
    psychomania wrote:
    starting petty arguments to cover up your mistakes like you did yesterday. 
    i'm not covering up my mistakes , what mistakes do u mean ?? yesterday , i said that i said that because it's in Nokia warranty of the authourised nokia resellers in my region and didn't know that this doesn't apply all over the world
    psychomania wrote:
    This forum exists to help people, not for you to spam posts without thinking about the consequences.
    it's not for me, it's for all NOKIA users, and i'm not spamming as if i was that, so how could i stay all that time, solving others problems with alot of thanx
    even if i solved 2 problems , that proves that i'm not spamming
    so .... welcome bro in NOKIA USERS discussion board
    -you can show appreciation to my posts if it helped or useful by pressing the green Kudo star beside my post that hepled
    -if my answer was the solution , so click accept as solution button
    Started From Nokia 3310 , Now with Nokia N97 v.22.0.110 + N900 PR1.2

  • Scanjet 7000n EWS problem after firmware update

    I recently upgraded the firmware on our 7000n scanner in the hopes it would add smtp over ssl. I updated the firmware by uploading it via the embedded web server. The update appeared to go smoothly with no problems or errors, however, the embedded web server no longer functions properly.  
    If I  enter the IP into the web browser it initially takes me to a blank page. I can refresh the page and then the "home page" of the scanner comes up. If I click the admin login, the login page comes up, but after logging in, I once again receive a blank page. At this point, refreshing the page does not work, but if I remove "/hp/device/SignIn/Index" and hit enter, the page comes back up and I am logged in as administrator. 
    The main problem comes when I go to try to reconfigure email settings. I can make it to "/hp/device/Send/Index"  where I select the check box for the server I want to edit, but once again, clicking edit takes me to a blank page.  At this point I can hit enter in the address bar, and it will bring the email settings page back up, but I never get to the Edit page after hitting the edit button. 
    I tried reflashing the firmware from a USB flashdrive, which also completed with no problems, but the EWS issue is still present. 
    I haven't been able to find any information about the issue online, and all google searches I've tried just bring up pages on how to install the firmware, and information on using the embedded web server, so it doesn't appear to be a common issue. 
    Does anyone have any idea what I can do to fix this? 

    Hello there,
    To get your issue more exposure, I would suggest posting it in the commercial forums since your product is a commercial product. You can do this at Commercial Forums.
    Enjoy your day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • E71 Backup/Restore problem after firmware update

    after i restore the data using the PC suite, I'm facing a connectivity problem, No MMS and web browsing are working, even after i re-install the settings from the provider and setup wizard, same thing, even the wireless connectivity is not working.
    note that they are working be4 i do the restore (plain phone).
    any recommendation.
    It's never too late to learn ....

    I upgraded my firmware (why do nokia call it 'software'?), which i kind of regret now. I don't see any difference to my phone, plus i hit a major problem.
    Before upgrading i backed-up my phone.
    After upgrading firmware i tried to restore the backup to my phone - wouldn't work!?!?!?!?! - plus the phone said that i had a massive error and had to take my phone back to retailer. it would not restart.
    Seriously crazy
    FIX:
    'Hard-reset' the phone (erases memory and takes you back to basic nokia phone software) -  While turning the phone on you hold down 3 buttons: " green-phone & 3 & * ". Hold down for about 10 sec's. The phone should start working again with the new firmware - albeit with only basic settings.
    Go to the backup-restore, and restore from your last backup.
         HOWEVER, UNTICK 'phone settings'.
    This should get almost everything back for you (calendar,contacts,etc), except for any software that you had previously downloaded and installed on your phone (e.g. google maps, fring, skype, youtube, etc). Easy enough to download & install again. Also, you might want to ring your phone company and get them to mms you the configuration settings for internet and mms again.
    WHY WAS THERE A PROBLEM? I believe that the old settings of the previous firmware are NOT compatible with the new firmware. This makes the phone effectively stop working when you restore the backup.

Maybe you are looking for