N97 Mini Notes traveler connection error

I have installed Notes traveler on Nokia N97 Mini. I could log on to our corporate Notes traveler server, download the client and installed it also. On completing the installation, Initial sync starts. I could never got it completed. I get an error "connection with serverort 80 lost initial sync not completed" exactly after 1 minute sync starts. I have might have tried and retried over 100 times with no success. Any suggestions?
Thanks,
Sanjay Bhagwat

I have experienced the "Connection error" problem for the past 6 months on the N97 Mini. There are no software updates to fix the problem and I have had the phone replaced 3 times by Vodafone. I have also had the SIM card swapped. Unfortunately, none of the above has worked.
The error does not seem to have a particular pattern, but happens several times a day, sometimes near the start of a call, sometimes 15 mins or so in. It doesn't seem to matter whether I am calling someone else or they are calling me. I'm not sure whether it matters if the other person is on a landline or a mobile. It also seems unrelated to the actual network signal I have.
The call goes silent and the then drops off with the error message "Connection error" on screen.
This is incredibly embarrassing if you're in the middle of a business call as it would appear to the other person that you have deliberately cut them off.
A software/firmware fix for this would be appreciated as it is difficult to use this device adequately for its main purpose: as a phone!

Similar Messages

Heart beat could not open connection, error code 110

Hi, where can I find error codes for NFR and NSM?
I have problems with some agents connecting to the engine:
2/17/2010 16:02:55 EngineInterface: Heart beat could not open connection, error code 110
Both engine and agent runs on the same server (10.236.19.147):
AgentNCP Service Config
Host Address: 10.236.19.147
Service Ports: HTTPS: 3037 HTTP: 0
Data Path: /var/opt/novell/filereporter/agentncp
Debug Logging: Enabled
Heartbeat: 60 seconds
Engine Address: 10.239.19.147:3035
Use SSL: Yes
Alternate Hostname: huanovellfs1
Engine Service Config
Host Address: 10.236.19.147
Service Ports
Client HTTPS: 3033 HTTP: 0
Agent HTTPS: 3035 HTTP: 0
Data Path: /var/opt/novell/filereporter/engine
Debug Logging: Enabled
Heartbeat: 60 seconds
DSI Address: 10.236.19.89:8009
Use SSL: Yes
Scans per Volume: 2
Another OES2 server connects fine to the engine, butI have a Netware agent, which also fails to connect:
Feb 17, 2010 4:08:11 PM SR Interface: Heart beat could not open connection.
NFR is 1.0.0
Thanks for any input.
Istvan

Hi Istvan! Sorry for the delay in our response! we are in the process
of building a list of error codes for everyone! in the meantime the 110
means the following:
// Couldn't create a new network interface
#define CC_STATUS_CCS_CANT_CREATE 110
Is this an NSM integration installation?
Also, remove the alternate hostname.
If you don't mind, let's move this support issue to
filereporter"@"novell.com!
Thank you!
icseke wrote:
> Hi, where can I find error codes for NFR and NSM?
>
> I have problems with some agents connecting to the engine:
>
> 2/17/2010 16:02:55 EngineInterface: Heart beat could not open
> connection, error code 110
>
> Both engine and agent runs on the same server (10.236.19.147):
>
>
> AgentNCP Service Config
> ------------------------------------------------------------------------------
> Host Address: 10.236.19.147
> Service Ports: HTTPS: 3037 HTTP: 0
>
> Data Path: /var/opt/novell/filereporter/agentncp
> Debug Logging: Enabled
> Heartbeat: 60 seconds
> Engine Address: 10.239.19.147:3035
> Use SSL: Yes
> Alternate Hostname: huanovellfs1
>
> Engine Service Config
> ------------------------------------------------------------------------------
> Host Address: 10.236.19.147
> Service Ports
> Client HTTPS: 3033 HTTP: 0
> Agent HTTPS: 3035 HTTP: 0
>
> Data Path: /var/opt/novell/filereporter/engine
> Debug Logging: Enabled
> Heartbeat: 60 seconds
> DSI Address: 10.236.19.89:8009
> Use SSL: Yes
> Scans per Volume: 2
>
> Another OES2 server connects fine to the engine, butI have a Netware
> agent, which also fails to connect:
>
> Feb 17, 2010 4:08:11 PM SR Interface: Heart beat could not open
> connection.
>
> NFR is 1.0.0
>
> Thanks for any input.
>
> Istvan
>
>

N97 mini not BT with anything

OK i've just upgraded from N95 8gb to N97 mini. Great I thought I'll have no issues with paring and making calls with JVC car kit. Now my N95 worked perfectly with no dropped calls and it could stream audio and video to the JVC unit all day long with no issues...
I have a few questions.
The JVC has:-
HFP (hands free profile) 1.5
OPP (object push profile) 1.1
A2DP (advanced audio distribution profile) 1.2
AVRCP (audio/video remote control profile) 1.3
What has changed in the N97 from the N95 that none of this no longer works and more importantly how can I resolve this with phone software updates?? Is there anywhere on the planet that can make software's/apps to solve these gripes until BT is standardized??
Also I'm not interested in contacting Nokia as they'll do noting for me but when could I find the MD's email address as this option usually works alot better and faster from experience..

It would be nice to know if this phone works Bt with anything. I coonot connect to my HP notebook either!!! This is something never ever happened..tried USB, it works occasionally.
To expensive phone nort worth it

N97 mini USB cable connectivity issue

Hello all,
I've tried to connect my N97 mini with the micro USB cable, and it seems not to work.
When I connect the device, It asks me to pick PC Suite, I choose it, but then, when it tries to install the phone on my laptop, it just doesn't work, and it says that the hardware might not work ok.
I have uninstalled and installed Ovi Suite 2 times, I have resetted the phone and it doesn't work.
It worked first with Bluetooth, but now that I try again, it just doesn't work anymore.
Please let me know what I can do.
Thank you!
Luisa
Message Edited by luisalunac on 21-Jan-2010 07:38 PM

Same issue here. Reset phone, cleaned and reinstalled all software but no success.
I tried the cable with different nokia models and it works fine, it is definitely a N97 mini issue.
Waiting for a firmware update to get this really basic function

N97 mini not synching with Nokia Ovi Suite 2.2.1.2...

I've had my N97 mini for a few days and I was so hoping that it would be a better experience than the Sony Ericsson I had. Seems not.
Running Win7 32-bit, NOS 2.2.1.23, all software updated on PC and phone, but I just cannot get the phone to sync with the PC. When I connect the phone to the PC with the USB, it does its recognition, and all the Sync button light up and become live. But clicking them does nada.
The strange thing is that it has worked, when I first installed it on the PC.
Also, PC Suite does not start up when I connect the phone to my PC even though I've told PC Suite to start up when the phone is connected. What's going on?
And one last rant... why on earth is there no timed auto-sync facility on PC Suite?? Everytime I want to sync, I have to press buttons. Even my dumb Sony Ericsson software could do that!
Cheers,
Mart

Could you please follow this?
1. Uninstall Ovi Suite, PC Connectivity solution and Nokia Connectivity cable drivers from Add/remove program if anything is there.
2. Delete the files from here If anything is there
C:\Documents and Settings\User\Application Data\Nokia\Ovi Suite
C:\Documents and Settings\user\Local Settings\Application Data\Nokia
C:\Documents and Settings\All Users\Application Data\OviInstallerCache
3. Please search and download MSI clean up utility from microsoft website
Once installed please select the programs related to Nokia and click remove.
Restart Computer.
Then download from microsoft website and install Windows Installer, so that the installer is upto date.
4. Restart the PC
5. Download and Install latest OviSuite http://europe.nokia.com/support/download-software/nokia-ovi-suite
Please THANK me by clicking on the ****WHITE STAR** ( Giving KUDOS) the big GREEN BOX to your LEFT .
It will help me to serve you better !!!!!
Thanking You

N97 Mini - Pop-up connection Internet

Hello,
I have a N97 mini since 3 month.
I not have a phone plan with internet and i don't need that.
But i have always a pop-up for a internet connection. I would like remove this pop-up.
Thanks,
Alexandre.

You mean the pop up asking for internet connection?
its likely due to some preinstalled app like Nokia email. Go to Menu>Settings>Application manager>installed apps.
If you find my post helpful please click the green star on the left under the avatar. Thanks.

Adobe Air Bug: embedded .flv in .swf does not start - Connection Error

Hi,
I have embedded an .flv video into an .swf (using Captivate CS5)
Then I use Dreamweaver and insert the swf into html.
So far everything works ok, the video is displayed.
Now I create an Air File in Dreamweaver.
Result; The video is not displayed. Message: "Connection Error"
I am not a programmer. Do I have to change the .xml file or is there any other fix for this?
Thank you very much!
Claus

This would be somewhat usefull if we where calling the FLV from javascript. However, both Clause and I are calling the flash object from the object tag. This is the default from Dreamweaver and also the prefered method for embeding a swf (my case) into a HTML Air app. The codebase I am using to create my Air app is modified html5 from the client's current website. (they would like this app to "look and work like the site")
For me, all is good exept the video. This app has to work offline or I'd just call the video from the website.
Is there a working example somewhere out there we can look at?
Life would be so much simpler if AIR supported the <video> tag in the webkit html engine. I'll use h.264. I promise!
Chris

Mac mini not keeping connection with Cisco wireless access point

I am trying to get my wife's Mac Mini to keep it's connection with the wireless network at her school. They are using a Cisco access point (not sure of the model) which works fine with my G4 Powerbook and the numerous Macbooks being used there, but for some reason her Mac Mini drops the connection after 4 or 5 minutes, at which point she needs to log right off for it to reconnect (as opposed to just turning the card off and on again). I have already gone through the deletion of the Networkinterfaces.plist file, and recreation of the Airport card profile process, but this only kept the interface active for about 36 hours, then it was back to the same old problem. At this point I am thinking "flakey card"...before I ship it off to Apple, can anyone offer any other possible solutions?

After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!

N97 mini: Automatic WAP connection during the nigh...

Only recently got the phone and I've noticed that, usually at around 11.50pm, there is an outwards WAP connection for about 3.30 mins.
This would be fine if I had free mobile internet on my contract but I don't. My network (Vodafone) charges 50p a day (counted from 12am to 12pm) for unlimited internet so I can see this getting unnecessarily costly.
Has anyone got any idea why it is connecting and how I can prevent it?
Thanks in advance

If you can find the app that's connecting you may be able to go into installed apps and select it, then select suite settings and set to always ask or One in internet access point. Also in browser settings set access point to ask when needed, then it won't connect unless you allow it ! You can of course , as suggested, remove all access points (or get a data bolt on from vodafone )
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

N97 mini - losing WLAN connection

Hi Again!
IS there anyway to set the phone to stay connected to your wirelss internet - it connects fine but as I browse seems to disconnect itself and go back to mobile internet??
ANy advice?
Anna
Solved!
Go to Solution.

Sounds like your browser setting to me. There are 2 things you need to do.
First is to make sure that your wifi is filed under Internet in your list of Destinations. To do this, goto Settings>Cnnectivity>Settings>Destinations>Internet, Make sure your wifi is listed here and it is higher than the mobile internet on the list of priorities. If not you need to reorganise by longpressing your wifi access point and following the on screen instructions.
The second thing you need to check is from withing the browser. So start the browser, now click on Options>Settings>General>Access Point, make sure this is set to Internet.

N97 Mini not starting up

Yesterday my battery went flat, and now it is not starting up any longer, I can charge it, sometimes I get vibration, but nothing more. What data will I lose when hard resetting? SMS? Pictures? Notes?

You will lose anything saved on C phone memory, but it will be far more use than a 'Brick' ? Stuff on E or F will be ok !
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

N97 Mini Bluetooth problems

Hi: I have used to have a N86 which worked flawlessly with my 2005 Mitsubishi Outlander Handsfree system. But when I changed my phone to the N97 mini, it pairs fine but doesn't work properly.
When I call manually from the phone, the handsfree takes over and I can carry on conversation with the handsfree.
When I initiate a call from my car's voice activated handsfree bluetooth, nothing happens with the phone. It freezes my handsfree (radio) for two minutes. Then after two minutes, my phone says disconnected from handsfree, then reconnects automatically. I still cannot initiate a call from the car. But i can still call out as aforementioned.
When I receive a call in the car, the handsfree engages my phone as it should. So no problem receiving calls.
Please advise if this is a bug with the N97 becuase I have no problems with the N86.
THanks

Well, - I'm having the same problem as described in the first post. The N97 mini connects flawlessly with some PCs, headsets, and handsfree car systems.
I disagree with the purpose of remote SIM mode as before mentioned. Remote SIM access is to support the rSAP (remote SIM access profile) installed in some premium handsfree systems (like in my Skoda Superb) and basically lets the handsfree system 'steal' your SIM, including PIN etc. over BT for use with its own built in phone.
But in my new Mazda MX-5 I am having trouble to place calls with the handsfree car system. It is not a rSAP capable system and I have tried with and without rSAP in the N97 mini enabled, to no avail.
The N97 mini pairs fine and I can receive incoming calls. Also, I can place calls from the device itself, but when I try to place a call over the car's handsfree system it basically freezes for a few minutes before the car system throws an error. During these minutes I can see on the car display that it looses connection to the phone, albeit the N97 mini still shows connected state. Once these 1 or 2 minutes have passed, the phone shows disconnected, and then reconnects immediately. By experimenting a bit, I found that when I change the BT visibility, from not visible to visible or vice versa, during those minutes, the phone catches up with the number and dials.
And yes, my N97 mini is on the latest FW (12.0.110).
It's a pity that this problem is obviously already so old, that I have little hope Nokia is going to fix it. My old 6600i slide, and my wifes 6131 are working like a charm, unfortunately I need the N97 mini to work for other reasons ...
Despite I don't know if the N8 would work, it's not an option since it's not supported by PC Suite anymore, thus doesn't synchronize with Lotus Notes, which is what I need at work.
Any help would be greatly appreciated ... thanks

N97 mini won't save wep key

when setting my n97 mini up to connect via wireless it doesn't remember the wep key and asks for it every time I try to connect - how can I get it to save it?

Then you both need to look at this thread.......
/t5/Software-Updates/quot-Internal-module-error-quot-in-NSU-fix-offered-here/td-p/88351
If a reply has solved your problem click Accept as solution button, doing it will help others know the solution. Thanks.

Connection Error - Phone, SIM or Network? - am rea...

Hello,
For the past week I have been having the odd problem with when trying to make a call, or sometimes recieving a call (when in a full signal area my phone not ringing at all). Usually when I make the call what happens is I get the "Connection Error" message appear, sometimes as well during a call this comes up.
Now like I said this was happening for a week (maybe a little bit longer), it was occasionaly though so didn't casue too much of a problem. I have however just changed my handset for a SIM-free N85 and the problem got a whole lot worse so I contacted T-Mobile who were very helpful in checking it out, initially their response was handset issue but as it was happening on my old handset as well I managed to get them to change the SIM.
Well the calls I make now are going through ok, so far not one connection error but I am still getting the drop outs during the calls but not all the time. I have bene ont he phone for 30 mins without an issue, then a drop out after 10 mins on a different call, then maybe a call for 25 mins before a drop out.
Personally I think this is sounding like a network issue more than a handset. The new SIM has helped and the last one did get transfered betwee phones several times over the space of 2 1/2 years so a bad connection would not supprise me.
The next thought is that it could be the handset but this seems really unlikely as it was affecting my old N95 as well. Is anybody aware of any issues with the N85 having connection problems? (I know there is the N-Gague one from a search of the forum).
I am basically looking for some opinions as I am quite stumped, having to change the phone although not impossible will only happen if it is deemed to be a handset fault. I am not sure that it is but a new SIM and T-Mobile saying the network is ok is ruling out the list of things it could be. But then the fact that it affected my old handset as well would imply that it is more network related.
As far as the network I have had this problem in a wide area, not just at home. In areas that are 15 miles upto 60 miles away from where I live.
Any suggestions of what else to try would be greatly appreciated.
Lee
Message Edited by lsr1981 on 01-May-2009 01:14 PM

I was JUST checking that. It was in fact unchecked. I started messing around with it, I checked it and set the limit to 50GB and the warning to 25GB and I was able to turn the hotspot back on. (Not that I'd hit the limit of 50GB) I wonder if that setting is left unchecked, that there is a preset limit configured to it that can't be changed?
OH, and it's a DROID4 phone, I picked the wrong phone when posting the question.

Sun Java Web Console can not be connected over a browser through port 6789

Symptom:
If i want to connect the Sun Java Web Console with a Browser (Tried: Firefox and IE) over https://x6220:6789 the browser connects to the server but nothing more occures. Important: It is not a connection error!
What is the Problem:
I now cannot access the Sun web console server through a browser over port 6789. Before the installation of the Sun Management Center 4.0 it worked.
System Overview:
I have a Sun Blade x6220 with Solaris 10 8/07 witch is member of a two node sun cluster 3.2.
Some Troubleshooting information:
*# netstat -an | grep 6789*
*.6789 *.* 0 0 49152 0 LISTEN
127.0.0.1.6789 127.0.0.1.32852 49152 0 49152 0 CLOSE_WAIT
172.16.18.66.6789 172.16.18.67.32856 49640 0 49529 0 CLOSE_WAIT
172.16.18.66.6789 172.16.18.67.32858 49640 0 49529 0 CLOSE_WAIT
172.16.18.66.6789 172.16.18.67.32865 49640 0 49472 0 CLOSE_WAIT
172.16.18.66.6789 172.16.18.67.32866 49640 0 49529 0 ESTABLISHED
127.0.0.1.32916 127.0.0.1.6789 49152 0 49152 0 FIN_WAIT_2
127.0.0.1.6789 127.0.0.1.32916 49152 0 49152 0 CLOSE_WAIT
Who is listen on port 6789:
12930: /usr/java/bin/java -server -Xmx128m -XX:+BackgroundCompilation -XX:Per
*# svcs |grep webconsole*
online 10:10:01 svc:/system/webconsole:console
*# smcwebserver status*
Sun Java(TM) Web Console is running
*# svccfg -s svc:/system/webconsole listprop*
options application
options/stability astring Evolving
options/tcp_listen boolean true
console-multi-user dependency
console-multi-user/entities fmri svc:/milestone/multi-user
console-multi-user/grouping astring require_all
console-multi-user/restart_on astring none
console-multi-user/type astring service
general framework
general/entity_stability astring Unstable
*# cat /usr/share/webconsole/webapps/console/WEB-INF/app.xml*

<authTypes>
<authType name="">
<classType></classType>
<permissionParam name=""></permissionParam>
</authType>
</authTypes>
But now:
*# wcadmin list*
I'm waiting for some output till today but nothing...nothing---nothing!
Question:
What else could not work probably? Thank you for help.

I also couldn't attach to port 6789
+21:38:33:helaman:root>svcadm enable webconsole+
+21:38:58:helaman.:root>svcs webconsole+
STATE          STIME    FMRI
offline*       21:53:17 svc:/system/webconsole:console
+21:54:02:helaman:root>+
Looking at the log didn't help
+21:55:26:helaman:root>cat /var/svc/log/system-webconsole:console.log+
+[ Aug 24 21:54:06 Executing start method ("/lib/svc/method/svc-webconsole start") ]+
Starting Sun Java(TM) Web Console Version 3.1 ...
Cannot determine if console started successfully
+[ Aug 24 21:54:55 Method "start" exited with status 0 ]+
+[ Aug 24 21:54:55 Stopping because all processes in service exited. ]+
+[ Aug 24 21:54:55 Executing stop method ("/lib/svc/method/svc-webconsole stop") ]+
The console is stopped.
+[ Aug 24 21:54:56 Method "stop" exited with status 0+ ]
The service started and stopped ....
so I looked at the debug file in */var/log/webconsole/console/console_debug_log*
+==============================================================+
Java Web Console Version 3.1 started on Sun Aug 24 21:54:54 PDT 2008
+==============================================================+
java.lang.ClassNotFoundException: org.apache.catalina.core.ApplicationContextFacade$1
+ at java.net.URLClassLoader$1.run(URLClassLoader.java:200)+
+ at java.security.AccessController.doPrivileged(Native Method)+
+ at java.net.URLClassLoader.findClass(URLClassLoader.java:188)+
+ at java.lang.ClassLoader.loadClass(ClassLoader.java:306)+
+ at java.lang.ClassLoader.loadClass(ClassLoader.java:251)+
+ at org.apache.catalina.security.SecurityClassLoad.loadCorePackage(SecurityClassLoad.java:53)+
+ at org.apache.catalina.security.SecurityClassLoad.securityClassLoad(SecurityClassLoad.java:40)+
+ at org.apache.catalina.startup.Bootstrap.init(Bootstrap.java:210)+
+ at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:390)+
Looks like the updates that I did lost a jar file ... Does anyone know what JDK I should use ... I have the following
+22:03:21:helaman:root>uname -a+
SunOS helaman 5.10 Generic_137112-05 i86pc i386 i86pc
+22:03:26:helaman:root>cat /etc/release+
+ Solaris 10 5/08 s10x_u5wos_10 X86+
+ Copyright 2008 Sun Microsystems, Inc. All Rights Reserved.+
+ Use is subject to license terms.+
+ Assembled 24 March 2008+
+22:03:32:helaman:root>java -version+
java version "1.6.0_07"
Java(TM) Platform, Standard Edition for Business (build 1.6.0_07-b06)
Java HotSpot(TM) Server VM (build 10.0-b23, mixed mode)
+22:03:36:helaman:root>env | grep JAVA+
JAVA_HOME=/usr/java
+22:03:41:helaman:root>ls -dall /usr/java+
lrwxrwxrwx   1 root     root          10 Aug 24 21:45 /usr/java -> jdk/latest
+22:03:53:helaman:root> smpatch analyze+
+ You have new messages. To retrieve: smpatch messages [-a]+
No patches required.
+22:06:06:helaman:root>+
Any insight on this would be much appreciated.

N97 Mini Notes traveler connection error

Similar Messages

Maybe you are looking for